Tender For Kulpahar Nagar Panchayat Reorganization Water Supply Scheme Distt.Mahoba Under Amrut 2.0 - Civil Works 2 Wtp Works 3 Survey, Investigation, Soil Testing, Planning, Design And Drawing Construction, Commissioning Etc. As Per Design And Drawin, Mahoba-Uttar Pradesh

TDR : 51611976

Tender Notice
Corrigendum Details
BOQ

Expired

Mahoba , Uttar Pradesh

Tender Brief : Corrigendum : Tender For Kulpahar Nagar Panchayat Reorganization Water Supply Scheme Distt.Mahoba Under Amrut 2.0 - Civil Works 2 Wtp Works 3 Survey, Investigation, Soil Testing, Planning, Design And Drawing Construction, Commissioning Etc. As Per Design And Drawin

Document Fees
₹ 23600 /-

EMD
₹ 5107000.0 /-

Tender Value
Refer document

Submission Date
13-11-2025

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !

Sr No	Corrigendum Date	Corrigendum	Type	New Submission Date
1	03-11-2025	Date Extension	Date	13-11-2025

Name of Work: KULPAHAR NAGAR PANCHAYAT REORGANIZATION WATER SUPPLY SCHEME DISTT.MAHOBA UNDER AMRUT 2.0

Sl. No.	Item Description
1	CIVIL WORKS
2	WTP works
3	Survey, Investigation, Soil Testing, Planning, Design and Drawing construction, commissioning etc. as per design and drawing provided by the contractor all in accordance with the relevant latest I.S. Codes and approved by the Engineer as per conditions of the bid documents. The design and drawings provided by the contractor should be Vetted by any IIT Institute or Government Engineering College approved by the Engineer, on contractor\"s cost. For construction of 9 MLD WTP on latest technology ., Admin Building with Command Control Room, and fire fighting arrangements, first aid arrangements Cascading Aerator, Inlet chamber, alum dosing, pre-sedimentation Tank/Rapid Mix/Vertical Flow Clarifloculator/Rapid Gravity Filter with Back Wash Arrangement/Proper Sludge Disposal and Backwash water disposal arrangements to nearest drain/low laying area& Appurtenant Works of the above-mentioned capacity, automated through PLC with outputs to SCADA, walkway in between WTP components with railing, Guard Room, Chemical Store House, Gaseous Chlorination Plant with leak detection and absorption system (Cooling tower type), chlorine safty kit with tools, Development of WTP area with plantation, Rainwater harvesting unit andwith centraly located adequate LED light of 200 Watt High mask (12 M Hight, 8 nos LED) . Lean concrete to be used of grade not less than M-15 and other structures in minimum M-30 grade of concrete. Cement and steel should be as per approved by the Engineer/IS code.Collapsible MS steel doors and aluminum windows to be provided including of three-coat whitewashing, internal two coat snowcem painting, external painting with apex ultima/equivalent paint, all steelwork must be painted with red oxide paint and two coat of anticorrosive paint etc. and internal and external electrificationincluding automation, instrumentation & SCADA, wireless telemetry (voice & data), including Water Testing Kits, Lab Building and essential lab equipment as mentioned in the related Items Including of supply of all materials, labor T&P etc required for proper completion of works as per direction of the Engineer. All works complete as per design and drawing approved by engineer incharge. contractor will have to provide four wheelers, two wheelers, with fuel & driver for supervision of work and computer/laptop with operator as mentioned in tender document.
4	INTAKE WELL WORKS
5	Survey, Investigation, Soil Testing, Planning, Design and Drawing, construction, commissioning etc. as per design and drawing provided by the contractor all in accordance with the relevent latest I.S. Codes and approved by the Engineer as per conditions of the bid documents. The design and drawings provided by the contractor should be vetted by any IIT Institute or Government Engineering College approved by the Engineer, on contractor\"s cost.For construction of Intake Well of minimum internal size of 10.00M Dia & 20.00 M Height with required foot bridge, water inlet opening having minimum intake capacity to meetout the raw water required for WTP by different inlet points, construction of stair case, Pump house, Balcony, stair case post column beams etc. Such that to fix required nos. of VT Pump mention in item number 20.00, Power Control Panels, starters, intrumentation and SCADA & wireless telemetry (Voice & Data), internal and external electrification with adequate LED lightings including Excavation in soil i.e. Kankar mixed morrom/soft/hard rock and lean concrete of minimum grade of M-15 and R.C.C. in grade M-30 or above, in raft/ pile foundation, Intake R.C.C wall with supply of all type of steel bars of approved quality and cement OPC 53/43 grade of any make approved by the Employer as per design and drawings and binding the same including binding materials, diversion arrangement of flow during construction by making bundh across the dam supply gunny bags, sand, their filling suitable size of steel garder, with chain puli arrangement, dismantling and refixing etc. and also supply and fixing of collapsible gate, collapsible door, almunium window as per relevent specifications also including of three coat white washing, internal two coat snowcem painting, external painting with appex ultima or equivalent paint, all steel work must be painted with red oxide paint and two coat of anticorrosive paint etc. and internal and external electrification of intake well, supply and fixing of three-row of 20 mm dia G (Midium) pipe railing with 65X65X6 mm M.S. Angle iron posts. Supply and fixing of aniet opening of required capacity as per requirements including of supply of all materials, labour, T&P etc. required for proper completion of works as per direction of the Engineer. Cost of VT Pumps, panels, SCADA panel board, pipe manifolds etc. are not covered in this item.
6	Intake well cum pump house 10.0 m internal dia meter 4.50 m height above floor level, the depth of pump 5.0m below lowest water level and total height of intake well 20.0m from bed level of intake well to floor level of pump house the intake well shall firmly base onsuitable foundation in i.e.d raft foundation as per design requirements construction of RCC balcony or floor level, the pump house shall consisting of RCC column & bricks masonry walls. Construction of RCC Channel up to intake well in required size/length as per design for smooth raw water intake in summer days. Supply and fixing as door & windows, supplying and fixing ISMB350, chain piling blocks, supply and fixing CI D/F SV & etc. , supply and fixing GI pipe railing 20mm dia seperated on 65x65x6mm MS angles 1.50m C/C either wide as site core & other fase of balcony,construciton of floor of pump house using coata stone painting of doors and windows and all concrete cement using approved paint 3 coats with 80 M long and 3.5 M wide foot over bridge as per approved design and drawings. All works complete as per design and drawing approved by engineer incharge
7	Rising Main & By Pass arrangement
8	Supply of the following size pipes including railway freight, insurance charges F.O.R. etc. complete.
9	350 mm dia D.I. Class K-9
10	250 mm dia D.I. Class K-9
11	150 mm dia D.I. Class K-9
12	Supply of Specials for above pipe F.O.R destination including all Taxes and insurance.
13	Carting, laying and jointing of the following sizes of pipes into the trenches including cost of all jointing materials, labour and T&P, testing etc. complete. All works complete as per design and drawing approved by engineer incharge
14	350 mm dia
15	250 mm dia
16	150 mm dia
17	Excavation for pipe line trenches in Ordinary soil,(lime, clay or sand including lift up to 1.5m and lead up To 50m and refilling, watering, Ramming of excavated earth in to trenches and disposal of surplus earth up to 50 m from the center of the foundation trenches.
18	From Intake Well to WTP
19	Ordinary soil
20	Ordinary rock (mixed with kankar)
21	Hard rock (requiring blasting)
22	Hard rock (blasting prohibited)
23	Supply of following sizes of C.I. D/F sluice valves as per I.S. 780- 1960 tested to 10 Kg/sqm fixing in pipe line trenches, jointing and testing complete.
24	350 mm dia
25	250 mm dia
26	150 mm dia
27	Supply of C.I. Air valve
28	20 mm
29	Carting of D/F sluice valves of following sizes to the site of works lowering them into already prepared trenches and fixing them in position including supply of jointing materials such as bolt nut, rubber insertion white lead complete with excluding values and specials required but including the testing etc.complete excluding values and specials required but including the testing etc. complete.
30	350 mm dia
31	250 mm dia
32	150 mm dia
33	Air Valve
34	20 mm
35	Supply of all materials, labour, T&P and construction of following chambers as per type design including supply and materials, labour and T&P, testing etc. complete.
36	Masonry Type
37	Air Valve chamber
38	Provision of Thrust block
39	350 mm dia
40	250 mm dia
41	150 mm dia
42	Dismantling and reinstatement of following type of road surfaces for laying of pipe line including sorting out of serviceable materials and disposal of unserviceable materials. The firm must obtain permission from the relevant department for road cutting to lay the pipeline. onlycorrespondence will be done by the department .
43	C.C. Road
44	Crossing of Culvert/ Nala for laying pipe line including supply and materials labour, T&P etc. complete.
45	3.5M to 7.0M
46	Nahar Crossing (20M)
47	Crossing of road for laying pipe line including supply and materials labour, T&P etc complete.
48	Crossing of culvert/nala for laying pipe line including supply and materials labour, T&P etc complete.
49	Charges payable to PWD for permission of crossing Roads.
50	Charges payable to Forest Department for permission ofcrossing Roads.
51	Distribution System
52	Excavation for pipe line trenches in Ordinary soil,(lime, clay or sand Including lift up to 1.5m and lead up To 50m and refilling, watering, Ramming of excavated earth in to trenches anddisposal of surplus earth up to 50 m from the center of the foundation trenches.
53	Ordinary rock (mixed with kankar)
54	Hard rock (blasting prohibited)
55	Supply of the following sizes of pipes confirming to I.S. 4984:1995, I.S.-8329/2000 latest relevant of I.S.S. with couplers etc complete in all respect F.O.R. destination including all taxes and insurance.
56	HDPE Pipe PN-10 (O. D.) PE-100
57	110 mm dia
58	140 mm dia
59	160 mm dia
60	Supply of Specials for above pipe F.O.R destination including all Taxes and insurance.
61	HDPE Pipe PN-10 (O. D.) PE-100
62	DI Pipe K-7
63	200 mm dia
64	250 mm dia
65	300 mm dia
66	350 mm dia
67	400 mm dia
68	Addition (DI K-7) Pipe for connecting overflow to main supply
69	400 mm dia
70	Addition (DI K-7) Pipe for connecting overflow to main supply
71	350 mm dia
72	Supply of Specials for above pipe F.O.R destination including all Taxes and insurance.
73	DI Pipe K-7
74	Carting from the store (up to 8 Km.) The following sizes of pipe and specials to the site of work lowering them in to trenches and laying true to alignment and gradient including jointing, testing of pipeline and including supply of jointing material such as nut & bolts, rubber insertion, white lead etc. complate but excluding cost of trenching and cutting of pipes etc. Formaking of lengths but including making joints. All works complete as per design and drawing approved by engineer incharge
75	HDPE Pipe PN-10 (O. D.) PE-100
76	110 mm dia
77	140 mm dia
78	160 mm dia
79	DI Pipe K-7
80	200 mm dia
81	250 mm dia
82	300 mm dia
83	350 mm dia
84	400 mm dia
85	Addition (DI K-7) Pipe for connecting overflow to main supply
86	400 mm dia
87	Addition (DI K-7) Pipe for connecting overflow to main supply
88	350 mm dia
89	Supply of following types of fittings including railways freight,cartage up to store, all taxes and duties complete.
90	C.I. Double flanged Sluice /Scour Valves as per I.S. 780/1969 class-1 working pressure 10 Kg/sqm F.O.R Destination including all taxes and insurance.
91	C.I. Double flanged Sluice Valves
92	100 mm
93	125 mm
94	150 mm
95	200 mm
96	250 mm
97	Scour Valves
98	80 mm dia
99	Air Valves
100	25 mm
101	Fire Hydrants
102	80 mm
103	Carting of following fittings of following sizes to the site of works lowering them into already prepared trenches and fixing them in position including supply of jointing materials such as bolt nut, rubber insertion white lead complete with excluding values and specials required but including the testingetc. complete excluding values and specials required but including the testing etc. complete.
104	C.I. Double flanged Sluice Valves
105	100 mm
106	125 mm
107	150 mm
108	200 mm
109	250 mm
110	Scour Valves
111	80 mm dia
112	Air Valves
113	25 mm
114	Fire Hydrants
115	80 mm
116	Supply construction of following chambers as per type design including supply and materials labour, T&P etc. complete.
117	Masonry Type
118	Air Valves
119	Fire Hydrants
120	Dismantling of following type of surface including sorting out and staking of serviceable materials and disposal of unserviceable material up to a distance of 50m. The firm must obtain permission from the relevant department for road cutting to lay the pipeline. onlycorrespondence will be done by the department .
121	B.O.E. ROAD 60% old bricks
122	Bituminous Road
123	CC Road
124	Inter locking Road
125	Reinstatment of following type of road including supply of all material, labour etc complete. All works complete as per design and drawing approved by engineer incharge
126	B.O.E. ROAD 60% old bricks
127	Bituminous Road
128	CC Road
129	Inter locking Road
130	Crossing of Culvert upto 3.5M for laying pipe line includingsupply and materials labour, T&P etc. complete.
131	Crossing of Culvert 3.5M to 7.0M for laying pipe line including supply and materials labour, T&P etc. complete.
132	Crossing of Road for laying pipe line including supply and materials labour, T&P etc. complete.
133	3.5 M wide Road
134	7.00 M wide Road
135	Charges payable to PWD for permission of crossing Roads.
136	House connection on New Pipeline
137	Provision of House connection including Supply of all materials, labours T&P etc required for proper completion of work. (as following)
138	Making House Connection with distribution main including dismantling of road, supply, carting of specials, Lowering them into trances, fixing them in proper alignment and jointing including bailing out to water, necessary excavation for connection including all labour, T&P etc. required for propercompletion of the work. All works complete as per design and drawing approved by engineer incharge
139	In B.O.E. Roads
140	For 90 mm to 110 mm dia
141	For 140 mm to 160 mm dia
142	For 200 mm to 250 mm dia
143	For 250 mm to 300 mm dia
144	In Bituminous Road
145	For 90 mm to 110 mm dia
146	For 140 mm to 160 mm dia
147	For 200 mm to 250 mm dia
148	For 250 mm to 300 mm dia
149	For 350 mm to 500 mm dia
150	In C. C. Roads
151	For 90 mm to 110 mm dia
152	For 140 mm to 160 mm dia
153	For 200 mm to 250 mm dia
154	For 250 mm to 300 mm dia
155	For 350 mm to 500 mm dia
156	In C. C. Interlocking tiles Roads
157	For 90 mm to 110 mm dia
158	For 140 mm to 160 mm dia
159	For 200 mm to 250 mm dia
160	For 250 mm to 300 mm dia
161	For 350 mm to 500 mm dia
162	In Earthen Roads
163	For 90 mm to 110 mm dia
164	For 140 mm to 160 mm dia
165	For 200 mm to 250 mm dia
166	For 250 mm to 300 mm dia
167	RCC MCWR Cum Pump House
168	Supply of all materials, labour and T&P etc. complete for the construction of Ground RCC MCWR of 700 KL capacity & with 1.00m wide P.C.C. appron alround with 6 cm semi circular P.C.C. drain M.S. ladder with hand rails out side and inside the tank body proper ventilators at top, water level indicator, Lightening conductor as per latest I.S.I. or electricity rules, 1150mm dia medium pattern C.I. Manhole cover hinged with locking arrangement fixing and jointing vertical DID/F, pipes, specials and duck foot bends of required size for inlet, outlet fising of outlet sluice valve and wash out sluice valves with all jointing materials for proper completion and other appurtenant works including excavation in all type of soil & in rock etc. painting on exposed water proof cement paint, painting of pipes and ladder with approved anticorrosive paints also including testing of the CWR including carriage of construction materials by truck/ head load etc. upto site of work & also..
169	Supply of following size of DI D/F (K-7) (K-9) pipes conforming to IS8329/2000 or its latest amendment upto rail head including all taxes, duties insurance charges etc.
170	Inlet pipe 350 mm dia
171	Outlet pipe 350 mm dia
172	Over flow pipe 350 mm dia
173	Wash out pipe 100 mm dia
174	Carting of above size of DI K-7 and K-9 pipes upto site of work and lowering them into the trenches and laying true alignment and gradientand jointing of pipes complete (including testing of pipe lines and cutting of pipes for making up the length excluding the cost of trenches).
175	Inlet pipe 350 mm dia
176	Outlet pipe 350 mm dia
177	Over flow pipe 350 mm dia
178	Wash out pipe 100 mm dia
179	Supply of following dia ISI Mark sluice valve conforming to IS 780/1984 or its latest amendment of standard make (Kirloskar or IVC Make) including all taxes etc. and carting, loading and unloading upto departmental store.
180	100 mm dia (in wash out pipe)
181	Carting of following fittings/ sepicels to the site of work, lowering them into trenches, fising in position and jointing them with pipe lines and testing etc. complete (including supply of all jointing materials).
182	Sluice valves/ gate valves of 10 kg/cm2 working pressure
183	100 mm dia (in wash out pipe)
184	Supply of all materials, labour T&P etc all complete to construct sluice valve chamber of following sizes. Sluice valve chambers for 300 mm dia Sluice valve at outlet pipe.
185	Provide all materials, labours, T&P and construction over flow chambers as per departmental drawing or as directed by the Engineer.
186	Same as above but for wash out chambers.
187	Provision for the disposal of over flow water & wash out water from chambers to nearest suitable point of disposal including supply of pipes,its laying jointing excavation and protection work at the point of disposal.
188	PUMP HOUSE :
189	Supply of all materials labour T&P etc. for the complete construction of RCC Framed pump house adjacent to CWR as per approved design, drawing and standard specifications with 1 n wide PCC appron around along with 15cm semicircular PCC drains, RCC wall upto plinth level, to roof of pump house, laying case PCC 1:4:8, RCC floor, foundation and roof, 2m wide RCC plateform at plinth level, stair case from plateform to floor of pump house railing on the stair case and plateform foundation block of pumping plant RCC columns with bracket and longitudinal RCC beams to support moving gantry crane, plastering in the inner and outer brick masonary wall, flooring supply and fixing of doors, windows ventilators, painting on explosed surface with three coats of approved water proof cement paint, white washing in the inner surface, painting of door, windows ventilators, etc. supply and fixing of CI down pipes from roof to GL and other appurtenants works required to complete thepump house in all respect.
190	Capacity of MCWR 700 KL
191	Provision for soil testing
192	RCC OHT Zone-II
193	Supply of all the materials, labour T&P and construction of a R.C.C. Over head tank above ground level with main components, includingcost of soil testing and based on IS-3370 or liquid storage concrete in over head tank and foundation concrete as per specification in I.S.2911.
194	1000 KL with 22 m Staging
195	All components of OHT will be casted in M-30 concrete with cement, coarse sand and approved stone grit as per I.S. 11682 and I.S. 456
196	Minimum depth of foundation below original ground level will be 2.0
197	Seismic effects and wind load should be taken into consideration as I.S. 1893 for earthquake resistance and I.S. 875 part-III for wind load on structure.
198	The assumed bearing capacity of soil has been taken as 8 M.T. sqm
199	1 m wide RCC stair case from ground level to balcony.
200	M.S. ladder made of 50 x 50 x 6 mm angle section and 20 mm plain M.S. bars (specification of M.S. should be as per IS 800-2007) with hand rails of 20 mm medium class G.I. pipes on both sides in three rows from balcony to be top dome resting on an RCC plateform (75 x 75 cm and 10 cm thick) projecting from top ring beam and one alluminimum ladder inside thw tank body (from manhole in top dome to bootom dome).
201	1 m wide RCC balcony around the tank at the junction point of vertical wall and conical wall.
202	Proper R.C.C. railing and 20 mm dia medium class G.I. pipe (in 3 rows) on both sides of stair case, around the balcony at each landing from landing with top ring beam up to manhole on the top dome and at the periphery. The G.I. pipes will be supported on R.C.C. posts of 100 mm dia or on the posts made of 50 x 50 x 6 mm M.S. angle section, spaced at intervals not more than 1.5 m.
203	Proper ventilator at top dome in circular shape of 1.2 m dia along with an R.C.C. cover of minimum 1.50 m dia and 7.5 cm thickness, pillar of ventilator should be minimum 50 cm dia. The space between top dome and R.C.C. cover should be covered with mosquito net of standard quality along with expended mantled jail.
204	Lightening conductor as per I.S.S. 2309 of its latest electricity rules. It should consist proper elevation rod with 5test electricity rules. It should consist proper elevation rod with 5 of more fork points proper down conductors of prescribed mentale fork points proper down conductors of prescribed mental of proper size prescribed by ISS 2309-1969 and ISS 3013-1966.roper size prescribed by ISS 2309-1969 and ISS 3013-1966.
205	C.I. manhole of min 60 x 60 cm size made of M.S. channel section with adequate cover made of M.S. sheet of minimum 3 mm thickness hinged with locking arrangement. This manhole should be fixed at top domeat proper place.
206	Supply of fixing, jointing of following size of D.I. D/F pipes with D.I. D/F specials conforming to IS 329/2000 as vertical pipes for inlet, outlet, overflow and washout as per latest/ relevant I.S. specificationswith all jointing materials for proper completion of work including other appurtenant work and excavation in all types of soil.
207	Inlet pipe 250 mm
208	Outlet pipe 350 mm
209	Overflow pipe 250 mm
210	Washout pipe 100 mm
211	Supply and fixing of following sizes C.I. D/F sluice valves with Gear opreated as per I.S.S. 700/1969 or its latest pressure 10 kg/sqcm including cartage from its store to the site of work, lowering them into trenches, fixing in position & testing etc. complete.
212	Inlet pipe 250 mm
213	Outlet pipe 350 mm (Gear Operated)
214	Washout pipe 100 mm
215	Construction of bed blocks in 1:2:4 PCC with cement, coarse sand and approved stone grit under each duck foot bend to support the vertical pipes. These bed blocks should support on the raft not on the soil.
216	Construction of Masonary type sluice valve chamber for above sluice valve (3 No.) as per departmental type design and drawing including supply and fixing of 150 mm x 150 mm size C.I. surface box includinglocking arrangement.
217	Construction of washout/overflow chamber as per departmental type design and drawing.
218	Construction of P.C.C. floor & drain and all other necessary work as per departmental type drawing and design.
219	Weather Coat painting of all concrete surface and enamal painting of steel pipe works with three coats of approved cement paint and anticorrosive paints.
220	Testing & Commission etc. all complete work.
221	Testing of bearing capacity of soil from a reorganized Govt. Engineering college or as directed by department.
222	RCC OHT Zone-III
223	Supply of all the materials, labour T&P and construction of a R.C.C. Over head tank above ground level with main components, includingcost of soil testing and based on IS-3370 or liquid storage concrete in over head tank and oundation concrete as per specification in I.S. 2911.
224	350 KL with 24 m Staging
225	All components of OHT will be casted in M-30 concrete with cement, coarse sand and approved stone grit as per I.S. 11682 and I.S. 456
226	Minimum depth of foundation below original ground level will be 2.0
227	SMei. smic effects and wind load should be taken into consideration as I.S. 1893 for earthquake resistance and I.S. 875 part-III for wind load on structure.
228	The assumed bearing capacity of soil has been taken as 8 M.T. sqm
229	1 m wide RCC stair case from ground level to balcony.
230	M.S. ladder made of 50 x 50 x 6 mm angle section and 20 mm plain M.S. bars (specification of M.S. should be as per IS 800-2007) with hand rails of 20 mm medium class G.I. pipes on both sides in three rows from balcony to be top dome resting on an RCC plateform (75 x 75 cm and 10 cm thick) projecting from top ring beam and one alluminimum ladder inside thw tank body (from manhole in top dome to bootom dome).
231	1 m wide RCC balcony around the tank at the junction point of vertical wall and conical wall.
232	Proper R.C.C. railing and 20 mm dia medium class G.I. pipe (in 3 rows) on both sides of stair case, around the balcony at each landing from landing with top ring beam up to manhole on the top dome and at the periphery. The G.I. pipes will be supported on R.C.C. posts of 100 mm dia or on the posts made of 50 x 50 x 6 mm M.S. angle section, spaced at intervals not more than 1.5 m.
233	Proper ventilator at top dome in circular shape of 1.2 m dia along with an R.C.C. cover of minimum 1.50 m dia and 7.5 cm thickness, pillar of ventilator should be minimum 50 cm dia. The space between top dome and R.C.C. cover should be covered with mosquito net of standard quality along with expended mantled jail.
234	Lightening conductor as per I.S.S. 2309 of itslatest electricity rules. It should consist proper elevation rod with 5test electricity rules. It should consist proper elevation rod with 5 ofmore fork points proper down conductors of prescribed mentale fork points proper down conductors of prescribed mental ofproper size prescribed by ISS 2309-1969 and ISS 3013-1966.roper size prescribed by ISS 2309-1969 and ISS 3013-1966.
235	C.I. manhole of min 60 x 60 cm size made of M.S. channel section with adequate cover made of M.S. sheet of minimum 3 mm thickness hinged with locking arrangement. This manhole should be fixed at top dome at proper place.
236	Supply of fixing, jointing of following size of D.I. D/F pipes with D.I. D/F specials conforming to IS 8329/2000 as vertical pipes for inlet, outlet, overflow and washout as per latest/ relevant I.S. specifications with all jointing materials for proper completion of work including other appurtenant work and excavation in all types of soil.
237	Inlet pipe 150 mm
238	Outlet pipe 350 mm
239	Overflow pipe 150 mm
240	Washout pipe 100 mm
241	Supply and fixing of following sizes C.I. D/F sluice valves with Gear opreated as per I.S.S. 700/1969 or its latest pressure 10 kg/sqcm including cartage from its store to the site of work, lowering them into trenches, fixing in position & testing etc. complete.
242	Inlet pipe 150 mm
243	Outlet pipe 350 mm (Gear Operated)
244	Washout pipe 100 mm
245	Construction of bed blocks in 1:2:4 PCC with cement, coarse sand and approved stone grit under each duck foot bend to support the verticalpipes. These bed blocks should support on the raft not on the soil.
246	Construction of Masonary type sluice valve chamber for above sluice valve (3 No.) as per departmental type design and drawing includingsupply and fixing of 150 mm x 150 mm size C.I. surface box including locking arrangement.
247	Construction of washout/overflow chamber as per departmental type design and drawing.
248	Construction of P.C.C. floor & drain and all other necessary work as per departmental type drawing and design.
249	Weather Coat painting of all concrete surface and enamal painting of steel pipe works with three coats of approved cement paint and anticorrosive paints.
250	Testing & Commission etc. all complete work.
251	Testing of bearing capacity of soil from a reorganized Govt. Engineering college or as directed by department.
252	REPAIRING OF TWO NOS. EXISTING CWR/OHT (375 Kl &450Kl) (ZONE-I)
253	Supply and fixing on lightening Conductor on O.H.T. with proper arrangement and alignment including all labour and T&P etc. complete.
254	The lightening conductor consisting of an elevation rod, down conductor and earth plate shall confrom with the standars as required by the Electircal Inspector of U.P from time to time , Any amendment , addition etc. suggested or required by the Electircal Inspector shall be carried out.
255	Water lavel Indicator
256	Supply and fixing of water level indicator with suitable arrangement as per latest I.S. code with all labour T&P etc. complete.
257	All exposed surface of structure to be given three coats of approved exterior cement paint Berger/ narolac / Asian ( Such as apex) to give a smooth and even colour. the pipe system of above aprorn level along with the clamps to be painted with three coats approved synthetic paints. including supply of all labour material T&P necessory Scafolding etc. complete.
258	Repairs of O.H.T. wall, water tighteing work including all labour, material etc required for completion of work.
259	Repairs of cracks on concrete OHT including all labour material extraholding etc required for completion of work.
260	Repairs & Replacement of OHT pipes & Specials including all labour, material etc required for completion of work.
261	Repairs & Replacement of Valves & carting including all required for completion of work.
262	Replacment of both M.S. Ladder (inner & outer) & MS cover on top dome including all labour, material etc required for completion of work.
263	Site clearence and other unforseen items.
264	REPAIR OF EXISTING BOUNDARY WALL (ZONE-I)
265	First class brick work in 1:4 cement and local sand mortar in super structure and plinth including supply of all materials, labour T&P etc required for proper completion of work.
266	12 mm thick plaster with cement and local sand mortar in proportion of 1:6 over brick work, minimum thickness not be less than 10 mm including supply of all materials labour, T&P etc required for proper completion of work.
267	Provision of coping on the top of wall
268	Provision of barbed iron wire fencing to posts in four rows.
269	Provision M.S. iron angle (50x50x6mm) for the barbed wire fixing and 2 meter
270	Cement concrete with 20 mm gauge approved stone ballast coarse sand and cement in proporation 4:2:1 including supply of all materials, labour, T&P etc required for fixing M.S. Iron angle proper completion of work.
271	Raised pointing with cement mortar 1:4 consisting or cement and local sand on brick work including supply of all materials. labour, T&P etc, of the wrok.
272	White washing in three coat including supply of all materials, labour, T&P etc.
273	complete required for proper completion of the work
274	Providing plaster of Paris wall
275	to prepare the surface even and smooth complete.
276	Apex Ultima /Acrylic Exterior/ interior paint of approved brand & manufacturer & of required shade on under coated wall surface to give anuniform surface over one primer coat of white cement of approved brand after thoroughly brushing and rubbing the surface free from mortar droppings & other foreign matters including prepairing even surface with plaster of paris including supply of all material labour T&P etc required for proper completion
277	Site clearence &other unforceen item.
278	Existing Boundry Wall Length
279	Provide all materials, labour T&P etc. required for proper completion of work and construct pillars as per type design and fixing of gate 3.6 m wide gate and 1.2 m wicket gate.
280	Leveling, dressing, repairing of road in water works compound
281	REPAIR OF ONE NO. EXISTING STAFF QUARTER (ZONE-I)
282	Ist Class brick work in 1:4 cement and local sand mortar in superstructure including supply of all material, labour, T&P etc required for propercompletion of the work. (Thickness of wall to one brick thick).
283	12 mm thick plaster with cement & coarse sand mortar in 1:1:5 over brick work minimum thickness not to be less than 12 mm finished with 3 mmfloting coating of neat cement including supply of all materials, labour T&P etc. required for proper completion of the work.
284	Scraping old color washing and preparing the surface by removing loos material etc. including all labour and T&P etc complete.
285	40 mm thick over base concrete consisting of cement, local sand and 40 mm gauge first class brick ballast in the proportion of 1:4:8. For construction of apron 0.6 m wide.
286	White washing in three coat including supply of all materials, labour, T&P etc. complete required for proper completion of the work
287	Providing plaster of Paris wall putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.
288	Apex Ultima /Acrylic Exterior/ interior paint of approved brand & manufacturer & of required shade on under coated wall surface to give anuniform surface over one primer coat of white cement of approved brand after thoroughly brushing and rubbing the surface free from mortardroppings & other foreign matters including prepairing even surface with plaster of paris including supply of all material labour T&P etc required for proper completion of work.
289	Supply and fixing of flush doors including supply of all materials, paints, labour T&P etc. required for proper completion of the work.
290	Repair for electric fitting
291	Repair for sanitation work
292	Site clearence and other unforseen items.
293	BOUNDARY WALL, GATE SITE DEVELOPMENT & APPROACH ROAD (ZONE-II)
294	Provide all materials; labour T&P etc. for the Boundary wall as per direction of Engineer-in-charge.
295	Main compound
296	Long wall
297	Short wall
298	Deduction for Main Gate
299	Deduction for Wicket Gate
300	Total
301	Provide all materials, labour T&P etc. required for proper completion of work and construct pillars as per type design and fixing of gate 3.6 m wide gate and 1.2 m wicket gate.
302	Provide all materials, labour T&P etc. required for proper completion of work and construct Interlocking approach road.
303	Main road in compound
304	For OHT
305	For Staff Quarter
306	Total
307	Construction of Drain as per type design in all materials, labour T&P etc. required for proper completion of work inside campous for proper drainage. Size (300 mm x 300 mm).
308	Provision of Lighting in campous as per direction of Engineer-in-charge including all materials , labour T&P etc complete.
309	Provision of land ecapping and aboriculture in campous as per direction of Engineer-in- charge including all materials , labour T&P etc complete.
310	Excavation work in excavation by mechanical means (Hydraulic excavator)/manual means over are as (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer- in-charge.
311	Provide all materials, labour T&P etc. required for proper completion of work including leveling, dressing excavation and filling of earth where necessary for develop of water works site including carriage of earth.
312	For Main Compound
313	BOUNDARY WALL, GATE SITE DEVELOPMENT & APPROACH ROAD (ZONE-III).
314	Provide all materials; labour T&P etc. for the Boundary wall as per direction of Engineer-in-charge.
315	Main compound
316	Long wall
317	Short wall
318	Deduction for Main Gate
319	Deduction for Wicket Gate
320	BOUNDARY WALL, GATE SITE DEVELOPMENT & APPROACH ROAD (ZONE-III).
321	Provide all materials, labour T&P etc. required for proper completion of work and construct pillars as per type design and fixing of gate 3.6 m wide gate and 1.2 m wicket gate.
322	Provide all materials, labour T&P etc. required for proper completion of work and construct Interlocking approach road.
323	Main road in compound
324	For OHT
325	For WTP
326	For MCWR
327	For Staff Quarter
328	Total
329	Construction of Drain as per type design in all materials, labour T&P etc. required for proper completion of work inside campous for proper drainage. Size (300 mm x 300 mm).
330	Provision of Lighting in campous as per direction of Engineer-in-charge including all materials , labour T&P etc complete.
331	Provision of direction of Engineer-in-charge including all Engineer-in-charge including all materials , labour T&P etc complete.
332	Excavation work in excavation by mechanical means (Hydraulic excavator)/manual means over are as (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer- in-charge.
333	Provide all materials, labour T&P etc. required for proper completion of work including leveling, dressing excavationb and filling of earth where necessary for develop of water works site includingcarriage of earth.
334	For Main Compound
335	SUB STATION BUILDING (LT/HT ROOM / GENERATOR ROOM)
336	Provide all materials, labour T&P etc. and construct the sub statoinbuilding (LT/HT Room along with meter room) as per type design approved by Jal Nigam.
337	Raw Water Pumping Station Intake Well
338	Raw Water Pumping Station WTP
339	STAFF QUARTER FOR PUMP OPERATOR (ZONE-II)
340	Provide all materials, labour, T&P Complete and construction of a set of Single room Set Staff quarter for pump operator as per type design.
341	STAFF QUARTER FOR PUMP OPERATOR (ZONE-III)
342	Provide all materials, labour, T&P Complete and construction of a set of Single room Set Staff quarter for pump operator as per type design.
343	GROUND WATER RECHARGE WORK (ZONE-II)
344	Supply all materials, labour, tools and planta and provide arreangement for ground water recharge as per cost estimate attachment.
345	(i) At Water works
346	GROUND WATER RECHARGE WORK (ZONE-III)
347	Supply all materials, labour, tools and planta and provide arreangement for ground water recharge as per cost estimate attachment.
348	(i) At Water works
349	PUMPING PLANT AND ACCESSORIES FOR INTAKE WELL
350	Supply of Vertical type self-oil lubricated statically, dynamically, hydraulically balanced turbine pumpcapable of discharging at thefollowingdutyconditionasgivenbelowduetoallcauseswith surface discharge head confirming to IS:1710 and as amended as on date with accessories as per IS 5120/1977(Reconfirmed 2011) and as amendedthereaftertosuitthesitecondition.ThePumpBowlassembly and casing shall be CI IS 210 FG: 260 with suitable coating inside casing of 500 DFT, suitable for protection against corroision,erosion and prevent oxidation.Impeller and Wearing / Neckringshall be Duplex stainless steel CD4MCu (Chromium-24.5% minimum,Carbon < 0.04% ) as per ASTM A890 GrlA or DIN 1.4474-EN 10088, Hardness 220-260 BHN,pump shaft-Stainless steel AISI 410, pumps and line shaft sleeve - stainless steel with ceremic coating 700 BHN,Strainer-SS 304,coupling between pump ang motor - Flexible pin bush type and bearings shall be Anti friction L-10 with 60000 Hrs life at 1450 rpm.21mtr/suitablelengthcolumnassembly, with vertical hollow shaft.Squirrel cage induction motor(IS:126152011/IEC60034-1)suitablefortheabovepump continuous rated TEFC IP-55 with Class \"F\" insulation for operation in AC, three Phase/50 HZ (±5%), 415V (±10%), running with a speed of pump. Capacity as follows :-
351	3100 LPM / 80 Mtr. HEAD / 100 HP MOTOR (2w+1s) Head & discharge may increased as per site requirement
352	MAIN PIPING AND VALVES :-Supply of 200mm Main piping & valves complete of suitable size and quantity required for delivery side, bye pass arrangement and 250mm common Header upto 1 m. outsidethe pump house along with 250 x 200 x 250 mm A/F Tee (03 Nos) , 250 mm bend (01 Nos), 250 mm blind flange (01 Nos), D/F Pipes suitable sizeall necessary nuts, bolts, rubber packing, M.S Support for pipe, mechanical joints (04 Nos) and valve etc. complete in all respect Note -Suitable Sizeof Delivery line of each pumping plant and common header it may increase as per site conditions with best engineering manner
353	Motor operated actuator with sluice valve :- Supply of DI/DF sluice valve withElectrically integrated actuater (Totally enclosed,weather-proofanddustproofconstructionwithIP-67, protectionclass suitable for installationin any positionwithout lubrication,leakageorotheroperationaldifficultywithspecialgrease filledgearboxandsuitableformanualoperationforemergencywhich will automatically dis-engage on restoration of power to motor and with 10wattsingle phase spaceheaterandcontinuouslocalmechanical positionindicatorandindividuallyreplaceablecountergearassembly and with two torque and four limit switches with S.S. flap and operated withgeardrivencamsandofrating250Volt,5Amp,AC/DC,torque switch dialand with TEFC squirrel cageinduction) operatedsuitable to SCADAoperationsluicevalvehavingbodydoorcoverof gradedincast irontoIS:210Gr.Fg.260bodyanddoorringsofSSASTMA743Gr.CF8 andbearingblockofleadedtinbronzetoIS:318Gr.LTB2hingepinof stainlesssteelAISI:431.ValvesgenerallyconformtoIS:5312.Flangesto bedrilledasperIS:1538Part-IV&VI. Valves aresuitable for hydrostatictestpressureof10Kg./Cm2 forseatand15Kg./Cm2for body(PN-1.0)of following sizes
354	Valve actuator of size :- 200mm for pumpsor more suitable size as per site condition with best engineering manner
355	Valve actuator of size :- 250mm for common header or more suitable size as per site condition with best engineering manner
356	Non return valve :- Supply of DI/DF Single Door/ Multi Door Non return/reflux valve conforming to IS:5312/2003(partI & II) PN-16 to be fixed after pumps for 90% fast closing & 10% slow closing .
357	200 mm Dia for pumps or more as per site condition with best engineering manner
358	250 mm Dia for common header or more as per site condition with best engineering manner
359	CE/UL Certified Electromagnetic flow meter :- SupplyofCE/ULFullBorecElectromagneticFlowMeterofapproved make of following dia and specifications complete: Media : Water (Raw/ Chlorinated), Pressure:upto1.0 MPa,Processtemp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI316L/ HastelloyC276/ Tantalum, Lining Material : Hard Rubber/ Neoprene/ Poly-urethane(PU), Flange: SS /CS, FlangeStandard & Rating : ANSI 150, Coil housing : SS AISI 304/ Carbon Steel/ Die Càst Aluminium,with anticorrosivepaint&providecompletely sealed (leak proof) constructionasperrequirement‘ofIEC 60529, Accuracy : + 0.5 % M.V. velocity0.3to10m/s,Transmitter/signaconvertor Enclosure :Die CastAluminium, Power Supply: 80-240 V AC-5OHz,Output1: 4-20 mA,Output2:Pulse,CommunicationOutput:RS485/Heart, Display Type : LCD/ LED Display, Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibration and configuration parametersand totalizer value during power failure, Protection category- IP 68for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, cable.
360	Size 250mm for common header or more as per site condition with best engineering manner
361	ELECTRICAL ITEMS:-
362	Supply& laying of 1.1KV grade XLPE insulated armoured multi strand copper conductor cable of 3C x 35 sq.mm or more size suitable for pumping plant load from control Panel to respective Motors with lugs etc. (copperconductor should be electrlytic grade copper, purity >99.97% ISI marked asper IS:1554 P-I / IS :7098 P I)
363	MOTOR CONTROL CENTER (MCC) PANEL :-Single front, Indoor & floor mounted,cubical type Panel factory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shrouds and Gland Plate-3 mm thick) CRCA sheet duly power coateddust and vermin proof IP-54 /IS:2147, considered Earth Bus-Bar-GI Strip compitableto SCADA operation with RS485 Port consisting ofINCOMMING SECTION630A,50KA,TPN,ACB microprocessorbaseed (O/C,S/C)release-2 No with suitable rating auto phase reversal unit, Spreader Links & Extended ROH for - 1 No, 3 Phase Digital MultifunctionMeter -1No,DigitalVoltmeter0-500V -1No,Digital Ammeter 0-400A- 1 Nos, CT For meter Resin Cast CL-1400A/5A,15VA - 3 Nos, Phase indication light LED type 220V AC - 1 Set, Control MCB SP 6A ,10KA ABB - 3 Nos, CT Shorting Terminal - 4 Nos, Neutral Link - 1 No.OUTGOING SECTION200 A, 50KA, TPN, MCCBmicroprocessorbased (O/C,S/C) RELEASE - 3 No, SpreaderLinks &Extended ROH for MCCB- 3 Nos., 63A TPN MCCB 35KA- 2 Nos. Terminal 63A
364	Supply of Air Cooled Digital soft starter suitable for the LT motor offered for operation in AC three Phase 50Hz (+/- 5%), 415V(+/-10%) including linecontactorssuitablefornextstandardhigherKWrating,Over& Underloadprotection,shortcircuit&singlephasingprotectionwith frequency meter, Ammeter, Voltmeter, indicating lamp 6Nos, LED ON/OFF type and Start /Stop push button and Instrument Fuses, suitable to SCADA operation with RS485 Port rating suitable forcapacity 100 HP / 75 KW pumping plant
365	Supply of microprocessor based three phase sensing power factor correctionrelaypanel,IEC/EN61000-6-(2&4)having3CTsensing, sensitivity up to 50 milli amp secondary current , self analysing auto c/k settingaccordingtotargetedpowerfactorsetting,therelayshallhave digit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with RS 485, indication of switching on units, auto/manual status, and shall have overloadprotection,novoltrelease,havingmultiparameterlikeKW, KVA, KVAR rating capacity of 91 KVAR or more suitable as per site requirement
366	CE/UL Certified level transmitter for Intake well :- SupplyofCE/ULcirtifiedof RadarleveltransmitterCEmarkedwith following technical parameters and Interfacing with PLC panel including mounting arrangement.Output-4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68
367	CE/UL Certified Pressure transmitter for pumps and common header :- Supply of CE/UL Certified pressure transmitter CE markd with following technical parameters and Interfacing with PLC panel includingmounting arrangement. Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDAccuracy - +/- 0.1 % of full scale or better Enclosure- IP 68
368	Earthingwithcopperearthplate600mmX600mmX3mmthick including accessories, and providing masonry enclosure with cover plate havinglockingarrangementandwateringpipeof2.7metrelongetc. with charcoal/ coke and salt as required according to latest IS:3043Supplyingandlaying50mmX6mmG.I. stripat0.50metrebelow groundas stripearth electrode, including connection/ terminatingwith nut,bolt,spring,washeretc.asrequired.(Jointingshallbedoneby overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) ( 01 job = seprate Double Earthing of each pumping plant and its pannel as per IER )
369	Installation ,testing at site & manufacturer works or as per direction of Engineer Incharge andof all E/M equipments, power wiring of Electrical equipments and commissioning of the pumping plants.
370	3Ton or More suitable as per site requirement capacity hand operated over head Travelling (HOT)crane suitable for a span upto 6 Mtrs, and travel length upto 10 Mtrs. with clear lift upto 6 M including gear type chain pulley block and geared Travelling trolley complete with all accessories including girder
371	RubbermatsforelectricalpurposeasperIS:5424-1969, plain/chequered (1mX2m) - 10mm thickness
372	Cable trench Chequerred plate
373	Fire fighting equipments 4.5 Kg such as four nos. fire extinguishers ABC type, one set sand bucket with stand and grouting at site and one set Al strong plate and board.
374	Internal & External electrification of pumping station :-
375	Indoor Lighting
376	Surface Mounting
377	Providing & Fixing of IP-67 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non - yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85%, with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of ≥ 120 Im/Watt, THD < 10 % , p. f.≥ 0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K / 16000° / 6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard
378	Suspended Mounting / Surface Mounting
379	36W LED light fixture 2\"×2\" with acrylic / prismatic front cover.
380	Fans
381	Providing & Fixing of ISO Certified company made BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan as per PWD specification for electrical Works, Conform to all the performance requirements laid down in IS:374-2019 including all amendments, as applicable; & Carry BIS licensing (i.e. ISI marking) or Quality Certification such as ISO - 9001 or above. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc.) as required.
382	1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 )
383	Installation, testing and Commissioning of ceiling fan (any size) including wiring the down rod up to 30 cm with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required.with regulator
384	Providing & Fixing of Heavy duty capacitor start, copper wind Double ball bearing 900/1400 RPM single phase Exhaust fan as per PWD specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required.
385	450mm sweep (900/1400 RPM)
386	Fixing of fresh air fan/exhaust fan up to size of 300/450 mm on ply/ poly board of 6.0 mm in existing window frame including cost of ply, cutting of hole in ply. Nut bolts etc. as required.
387	Outdoor Lighting
388	Supply and fixing of all in one solar LED light fixturewith integrated high efficient Monocrystalline panel with Lithium (LiFePO4) Ferro Phosphate Battary wih BIS approved make. Luminaire should be secondary optic lences for better distribution with delivered efficacy of > 100 lumen per watt. Bidder shall have in house R & D Laboratory which is recognised by Ministry of Science & Technology Department , Govt of India/NABL.Bidder shall in house pole and luminaire manufacturing facility.Luminaire can be supplied with hybrid switch along with indicator to understand the source of power ( either from solar or AC supply).All the above should be integrated and should 1 system.
389	Compact Solar LED Street Light having protection of IP-67- 60W(MONO)18V / 12.8V27Ah /40W
390	Complete wiring of Pump house, HT & LT room with 1.5 sqmm and 2.5 sqmm with multistarned copper conductor 1.1 KV with required 6A,16A switches,sockets,MCCB etc .All sockets should be connected to sufficient size earth wire and seprate earthing for each pumphouse
391	250 KVA or more as per site requirement SUB STATION AT INTAKE WELL
392	Supplying of indoor type floor mounted metal clad, 11 KV VCB panel with 1No. VCBs, totally enclosed & fully interlocked, horizontal drawout, horizontal/ vertical isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and auto/manually closing breaker suitable for use on 11 KV, 3 Phase, 50 Hz A.C. supply with short circuit fault level of 100 KVa, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 1600Amps capacity, breaker featured with mechanical ON/OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 4 NO+4NC and equipped with following switchgears and accessories i/c connections suitable for 11 KV cable (cable entry from bottom/ top/side) end termination with heat shrinkable jointing material etc. as required. (Note- Cost of end termination not included in this item)(a) Incoming – ½ No 800Amp. VCB(b) 1* No. – 11 KV / 110 Volts PT Class 0.5 accuracy and 100 VA burder with 1 No. Voltmeter (0-15KV), analog/digital* type, selector switch for voltmeter and protection fuses/MCB for HT metering upto 12 KV on incomer.(c) 1* No. – (0-100 A) dual scale Ammeter, analog/digital* type, selector switches for ammeters.(d) 1* No. – Microprocessor based numerical relay with O/L, E/F and S/C protection.(e)1* No. – Set of dual core dual ratio 3 CTs 300/150/5/5 A of 15 VA burden and accuracy Class – 0.5 for metering and class 5P10 for protection.(a) Outgoing – 2Nos. 800Amp. VCB(b) 2Nos. – (0-100 A) Ammeters, dual scale analog/digital* type & selector switches for Ammeters.(c) 2 Nos. – Microprocessor based numerical relays with O/L, E/F & S/C protections.(d) 2 Nos. – Setofdualcoredualratio3CTs 100/ 50/5/5 A of 15 VA burden and accuracy Class-1.0 for metering and class 5P10 for protection.1. Supply of power pack 24 volts complete with battery and charging device.
393	Supply of 50 Sq.mm size XLPE HT cable from 11 K.V.UPPCL metering panel to 11 KV incoming H.T. switch gear panel and panel to transformer.
394	Supplying of 250 KVA or more suitable as per site requirements , 11/0.415 KV, 3 Phase, 50 Hz, Dyn 11, indoor ONAN type, copper wound transformer with OFF load tap changing arrangement on HV side in steps of +/- 7.5% to -7.5%,at each step of 2.5 %having cable end boxes on HV side suitable for 3x150sqmm XLPE cable of 33 KV grade and bus trunking arrangement on LV side complete with all accessories i/c first filling of filtered dehydrated oil and confirming to IS 1180 & as per specification attached complete in all respects as required at site.
395	Supplying of cubicall type LT panel suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized (preferably) design from CRCA sheet steel of 2 mm thick for framework and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, havingaluminium alloy bus bars of hight conductivity, DMC / SMC bus bars of high conductivity, DMC/ SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., bottom base channel of MS section not less than100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth barof size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from mainbus bar to switch gears with required size of Al. bus bars and control wiring with 50sq. mm. PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c providing following switch gears :-(I) Incoming : 2 Nos 630 Amps horizontal drawout type air circui+B12t breaker of fault breaking capacity 50 KA (Ics=Icu upto433 V manually operated, fitted with interlocked door, automatic safety shutters, mechanical ON/ OFF and service/test/isolated position indicators and frame earthing contact, conforming to IS 1397- 2 : 1993 as amended up-to-date complete with following accessories for each ACB.(a) Independent manual spring closing mechanism- 1 No.B10(b) Microprocessor release (EMI & EMC certified) for over current, earth fault & short circuit protection- 1 set.(c) Analog 96 mm square flush pattern /Digital* type Voltmeter (0-500 V), with selector switch & back up HRC fuses/ MCBs-1 set.(d) Analog 96 mm. square flush pattern/ Digital* type Ammeter (0-630Amp), with selector switch and one set of 3 nos. CT’s of ratio10/5A Class I accuracy and 15 VA burden- 1set. (e) 3 Nos. Phase indication LED lamps with2 Amp back up HRC fuse, breaker ‘ON’ indicating light with 2 A HRC fuse, test terminal block set, fuses, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required.(f) Shunt trip coil 220 V A.C.(II) Bus Couplers :1Nos. 320Amps drawout type, air circuit breakers offault breaking capacity 50 KA (Ics=Icu upto433 V) manually operated, with interlocked door, automatic safety shutters, mechanical ON/OFF and service/test/isolated position indicators and frame earthing contact conforming to IS 13947- 2 : 1993 as amended upto date complete with following accessories for each MCCB:(a) Independent manual spring closing mechanism- 1 No.(b) Breaker ‘ON’ indicating light with back up 2 A HRC fuse test terminal block, fuses, circuits contactors for positive electrical interlocking of breakers, etc. as required- 1 set.(III) Bus Bars :TPN aluminium bus bars of minimum of 630Amps capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bar cross section, size supports & their spacing etc. for withstanding fault level of 31 MVA for 1 Sec. (IV) Interlocking :Electrical through advance contacts in ACB’s (incomers & bus couplers) and mech- anical (castel key) interlocking should beprovided to ensure that only one supply is available at a time on each section of bus and to eliminate any possiblility of accidentally approaching two supplies at one bus section.(V) Outgoing :(a) 1 Nos. 630Amp 4 Pole ACB (Ics = kA upto 433 V)/SFU with HRC fuse (BC : 80 kA)(b) CT’s of ratio 10/5Amps 4Nos.4Set (1 set of 2 Nos.)(c) Analog 96 mmsq/Digital* type ammeter (0-100Amp) with selector switch set.
396	Supply and laying of 650/1100 volt grade 240sq mm 3½ core PVC Armoured Aluminium cable from transformer to L.Tpanel and from outgoing panel to distribution panel (1x3½x240 sq mm)
397	Making Earth pit for earthing complete in all respect. Earthing system shall executed as per IS:3043 and I.E. rules.
398	Installation and commissioning of 11 KV/0.4 KV substations including HT Panels and L.T. main control panel including all labor T&P complete in all respect.
399	Supply and making of indoor cable end termination joint kit of size 70 sq mm 3 core for 11 KV H.T. XLPE cable
400	Supply and making of outdoor cable end termination joint kit of size 240 sq mm 3 core for 11 KV H.T. XLPE cable
401	Provision for routine testing of equipments such as transformer, HT Panels and main LT Panel at manufacturer’s works.
402	NOC from Electrical safety department for all field installations such as pumping plants, substation etc.
403	PUMPING PLANT AND ACCESSORIES FOR MCWR TO ZONE-( I+II )
404	Supply of Vertical type self-waterlubricated statically, dynamically, hydraulically balanced turbine pumpcapable of discharging at thefollowingdutyconditionasgivenbelowduetoallcauseswith surface discharge head confirming to IS:1710 and as amended as on date with accessories as per IS 5120/1977(Reconfirmed 2011) and as amendedthereaftertosuitthesitecondition.ThePumpBowlassembly and casing shall be CI IS 210 FG: 260 with suitable coating inside casing of 500 DFT, suitable for protection against corroision,erosion and prevent oxidation.Impeller and Wearing / Neckringshall be Duplex stainless steel CD4MCu (Chromium-24.5% minimum,Carbon < 0.04% ) as per ASTM A890 GrlA or DIN 1.4474-EN 10088, Hardness 220-260 BHN,pump shaft-Stainless steel AISI 410, pumps and line shaft sleeve - stainless steel with ceremic coating 700 BHN,Strainer-SS 304,coupling between pump ang motor - Flexible pin bush type and bearings shall be Anti friction L-10 with 60000 Hrs life at 1450 rpm.06mtr/suitablelengthcolumnassembly, with vertical hollow shaft .Squirrel cage induction motor(IS:126152011/IEC60034-1)suitablefortheabovepump continuous rated TEFC IP-55 with Class \"F\" insulation for operation in AC, three Phase/50 HZ (±5%), 415V (±10%), running with a speed of pump. Capacity as follows :-
405	2400 LPM / 54 Mtr. HEAD / 50 HP MOTOR (2w+1s)Head and discharge may increase and suitable as per site requirement
406	MAIN PIPING AND VALVES :-Supply of 150mm Main piping & valves complete of suitable size and quantity required for delivery side, bye pass arrangement and 200mm common Header upto 1 m. outsidethe pump house along with 200 x 150 x 200 mm A/F Tee (3 Nos), 200 mm bend (01 Nos), 200 mm blind flange (01 Nos), D/F Pipes suitable sizeall necessary nuts, bolts, rubber packing, M.S Support for pipe,mechanical joints (04 Nos) and valve etc. complete in all respect as per site conditions. Note - Suitable Sizeof Delivery line of each pumping plant and common header it may increase as per site conditions with best engineering manner
407	Motor operated actuator with sluice valve :- Supply of DI/DF sluice valve withElectrically integrated actuater (Totally enclosed,weather-proofanddustproofconstructionwithIP-67, protectionclass suitable for installationin any positionwithout lubrication,leakageorotheroperationaldifficultywithspecialgrease filledgearboxandsuitableformanualoperationforemergencywhich will automatically dis-engage on restoration of power to motor and with 10wattsingle phase spaceheaterandcontinuouslocalmechanical positionindicatorandindividuallyreplaceablecountergearassembly and with two torque and four limit switches with S.S. flap and operated withgeardrivencamsandofrating250Volt,5Amp,AC/DC,torque switch dialand with TEFC squirrel cageinduction) operatedsuitable to SCADAoperationsluicevalvehavingbodydoorcoverof gradedincast irontoIS:210Gr.Fg.260bodyanddoorringsofSSASTMA743Gr.CF8 andbearingblockofleadedtinbronzetoIS:318Gr.LTB2hingepinof stainlesssteelAISI:431.ValvesgenerallyconformtoIS:5312.Flangesto bedrilledasperIS:1538Part-IV&VI. Valves aresuitable for hydrostatictestpressureof10Kg./Cm2 forseatand15Kg./Cm2for body(PN-1.0)of following sizes
408	Actuator with Sluice Valve of size :- 150mm or more size suitable as per site condition for pumps
409	Actuator with Sluice Valve of size :- 200mm or moresize suitable as per site condition for common header
410	Non return valve :- Supply of DI/DF Single Door/ Multi Door Non return/reflux valve conforming to IS:5312/2003(partI & II) PN-1.0 to be fixed after pumps for 90% fast closing & 10% slow closing .
411	150 mm Dia or more size suitable as per site condition
412	200 mm Diaor more size suitable as per site condition
413	CE/UL Certified Electromagnetic flow meter :- SupplyofCE/ULFullBorecElectromagneticFlowMeterofapproved make of following dia and specifications complete: Media : Water (Raw/ Chlorinated), Pressure:upto1.0 MPa,Processtemp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI316L/ HastelloyC276/ Tantalum, Lining Material : Hard Rubber/ Neoprene/ Poly-urethane(PU), Flange: SS /CS, FlangeStandard & Rating : ANSI 150, Coil housing : SS AISI 304/ Carbon Steel/ Die Càst Aluminium,with anticorrosivepaint&providecompletely sealed (leak proof) constructionasperrequirement‘ofIEC 60529, Accuracy : + 0.5 % M.V. velocity0.3to10m/s,Transmitter/signaconvertor Enclosure :Die CastAluminium, Power Supply: 80-240 V AC-5OHz,Output1: 4-20 mA,Output2:Pulse,CommunicationOutput:RS485/Heart, Display Type : LCD/ LED Display, Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibration and configuration parametersand totalizer value during power failure, Protection category- IP 68for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, cable.
414	Size 200mm or more size suitableas per site condition for common header with best engineering manner
415	ELECTRICAL ITEMS:-
416	Supply& laying of 1.1KV grade XLPE insulated armured multi strand copper conductor cable of 3C x 25 sq.mmOR more size suitable as per load of pumping plantfrom control Panel to respective Motors with lugs etc. (copperconductor should be electrlytic grade copper, purity >99.97% ISI marked asper IS:1554 P-I / IS :7098 P I)
417	MOTOR CONTROL CENTER (MCC) PANEL :-Single front, Indoor & floor mounted,cubical type Panel factory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shrouds and Gland Plate-3 mm thick) CRCA sheet duly power coateddust and vermin proof IP-54 /IS:2147, considered Earth Bus-Bar-GI Strip compitableto SCADA operation with RS485 Port consisting ofINCOMMING SECTION400A,50KA,TPN,MCCB microprocessorbaseed (O/C,S/C)release- 02 No with suitable rating auto phase reversal uint , Spreader Links & Extended ROH for - 1 No, 3 Phase Digital MultifunctionMeter -1No,DigitalVoltmeter0-500V -1No,Digital Ammeter 0-400A- 1 Nos, CT For meter Resin Cast CL-1400A/5A,15VA - 3 Nos, Phase indication light LED type 220V AC - 1 Set, Control MCB SP 6A ,10KA ABB - 3 Nos, CT Shorting Terminal - 4 Nos, Neutral Link - 1 No. OUTGOING SECTION160 A, 50KA, TPN, MCCBmicroprocessorbased (O/C,S/C) RELEASE - 6 No, SpreaderLinks &Extended ROH for MCCB- 6 Nos., 63A TPN MCCB 35KA- 2 Nos. Terminal 63A
418	Supply of Air Cooled Digital soft starter suitable for the LT motor offered for operation in AC three Phase 50Hz (+/- 5%), 415V(+/-10%) including linecontactorssuitablefornextstandardhigherKWrating,Over& Underloadprotection,shortcircuit&singlephasingprotectionwith frequency meter, Ammeter, Voltmeter, indicating lamp 6Nos, LED ON/OFF type and Start /Stop push button and Instrument Fuses, suitable to SCADA operation with RS485 Port rating capacity 45 KWfor operating 50 hp motor
419	Supply of microprocessor based three phase sensing power factor correctionrelaypanel,IEC/EN61000-6-(2&4)having3CTsensing, sensitivity up to 50 milli amp secondary current , self analysing auto c/k settingaccordingtotargetedpowerfactorsetting,therelayshallhave digit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with RS 485, indication of switching on units, auto/manual status, and shall have overloadprotection,novoltrelease,havingmultiparameterlikeKW, KVA, KVAR rating capacity of 50 KVAR
420	CE/UL Certified level transmitter for CWR :- SupplyofCE/ULcirtifiedof RadarleveltransmitterCEmarkedwith following technical parameters and Interfacing with PLC panel including mounting arrangement.Output-4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68
421	CE/UL Certified Pressure transmitter for pumps and common header:- Supply of CE/UL Certified pressure transmitter CE markd with following technical parameters and Interfacing with PLC panel includingmounting arrangement. Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDAccuracy - +/- 0.1 % of full scale or better Enclosure- IP 68
422	Earthingwithcopperearthplate600mmX600mmX3mmthick including accessories, and providing masonry enclosure with cover plate havinglockingarrangementandwateringpipeof2.7metrelongetc. with charcoal/ coke and salt as required according to latest IS:3043 Supplyingandlaying50mmX6mmG.I. stripat0.50metrebelow groundas stripearth electrode, including connection/ terminatingwith nut,bolt,spring,washeretc.asrequired Having resistance of Maximum 1 ohm.(Jointingshallbedoneby overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) (01 job = seprate Double Earthing of each pumping plant and its pannel as per IER )
423	Installation ,testing at site & manufacturer worksof all e/m euipments or as per direction of engineer incharge , power wiring of Electrical equipments and commissioning of the pumping plants.
424	3Ton capacity hand operated over head Travelling (HOT)crane suitable for a span upto 6 Mtrs, and travel length upto 10 Mtrs. with clear lift upto 6 M including gear type chain pulley block and geared Travelling trolley complete with all accessories including girder
425	RubbermatsforelectricalpurposeasperIS:5424-1969, plain/chequered (1mX2m) - 10mm thickness
426	Cable trench Chequerred plate
427	Fire fighting equipments 4.5 Kg such as four nos. fire extinguishers ABC type, one set sand bucket with stand and grouting at site and one set Al strong plate and board.
428	Internal & External electrification of pumping station :-
429	Indoor Lighting
430	Surface Mounting
431	Providing & Fixing of IP67LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non - yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85%, with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of ≥ 120 Im/Watt, THD < 10 % , p. f.≥ 0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K / 16000° / 6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard
432	Suspended Mounting / Surface Mounting
433	36W LED light fixture 2\"×2\" with acrylic / prismatic front cover.
434	Fans
435	Providing & Fixing of ISO Certified company made BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan as per PWD specification for electrical Works, Conform to all the performance requirements laid down in IS:374-2019 including all amendments, as applicable; & Carry BIS licensing (i.e. ISI marking) or Quality Certification such as ISO - 9001 or above. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc.) as required.
436	1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 )
437	Installation, testing and Commissioning of ceiling fan (any size) including wiring the down rod up to 30 cm with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required.with regulator
438	Providing & Fixing of Heavy duty capacitor start, copper wind Double ball bearing 900/1400 RPM single phase Exhaust fan as per PWD specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required.
439	450mm sweep (900/1400 RPM)
440	Fixing of fresh air fan/exhaust fan up to size of 300/450 mm on ply/ poly board of 6.0 mm in existing window frame including cost of ply, cutting of hole in ply. Nut bolts etc. as required.
441	Outdoor Lighting
442	Supply and fixing of all in one solar LED light fixturewith integrated high efficient Monocrystalline panel with Lithium (LiFePO4) Ferro Phosphate Battary wih BIS approved make. Luminaire should be secondary optic lences for better distribution with delivered efficacy of > 100 lumen per watt. Bidder shall have in house R & D Laboratory which is recognised by Ministry of Science & Technology Department , Govt of India/NABL.Bidder shall in house pole and luminaire manufacturing facility.Luminaire can be supplied with hybrid switch along with indicator to understand the source of power ( either from solar or AC supply).All the above should be integrated and should 1 system.( For MCWR )
443	Compact Solar LED Street Light- 60W(MONO)18V / 12.8V27Ah /40W
444	Supply installation tesling & Commissioning of IS0 certiftedcompany made high mast lighting system (as per PLG 07 of ILP UK technical report no 7 of ILE UK /IS:875 Part-1 - 2015//BSEN10025/and IS:2062 )consisting of totally hot dip galvanised by single dipped method high mast, lantern carriage suitable for up to 12 nos luminaries with welded arm (excluding luminares), mast head frame assembly with full cover, including 1 No. LED 15 Watts aviation obstruction lights, double drum type self sustaining winch, integral power tool accesible from door with padlocking arrangement ( winch motor with control circuit) hot dipped galvanised heavy duty pipe lightening finial, S.S. ropes (AISI 316, 7 / 19 costruction), EPR insulated PCP sheathed trailing cable, including outdoor type control panel for auto on / off, reverse / forward motor operation and CC foundation of M - 25 grade complete as required as per IS 456/IS 2911. The mast is constructed from mild steel plates (as per IS 5986 Gr. 510 ) cut and folded to form a polygonal (Octogonal) section, telescopic jointed and welding as per BS 5135 and also provide test certificate for wind tunnel test for High mast fixtures. complete in all respect. (for WTP)
445	12.5 Mtr. HM (in 2 Section)
446	Providing & Fixing of IK07 IP-66 protected high power LED flood light system with Pressure diecast aluminium housing LM6/ ADC12 material, toughened glass diffuser with suitable lenses on LED to achieve various beam angles, 240 volt, 50Hz, of high power LED lamps . Integrated driver must be potted & has a unique BIS R number shall be high efficiency having efficiency more than 85 % and in compliance to BIS certified and T.C. certificate. The System level Luminaire efficacy >=120 Im/ wt with High Power LEDs is to be used . LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety . Input Frequency 50Hz‡3%, Power Factor >0.95 ,driver Efficiency >85% .THD(I) <10% , driver current <1000mA shown in LM79 report. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector Must be provided, Surge Protection Min >=4KV internal and 10KV external, System life of 30000 Burning hours with 70% of Initial Lumens maintained, color Rendering Index >70 and CCT 5700K + 1355K, Driver current <1000mA shown in LM79 report. Manufactures Word Mark/Name Engraved/Embossing/Screenprinting on die cast housing to allow traceability/authenticity. Fixture-shall be IS 10322 Complianced and also provide test Certificate/ report with liable warranty of product/accessories.
447	High Power LED Flood Light 200W
448	Complete wiring of Pump house, HT & LT room with 1.5 sqmm and 2.5 sqmm with multistarned copper conductor 1.1 KV with required 6A,16A switches,sockets,MCCB etc.
449	250 KVA or more as per requirements SUB STATION AT ( MCWR+WTP )
450	Supplying of indoor type floor mounted metal clad, 11 KV VCB panel with 1No. VCBs, totally enclosed & fully interlocked, horizontal drawout, horizontal/ vertical isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and auto/manually closing breaker suitable for use on 11 KV, 3 Phase, 50 Hz A.C. supply with short circuit fault level of 100 KVa, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 1600Amps capacity, breaker featured with mechanical ON/OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 4 NO+4NC and equipped with following switchgears and accessories i/c connections suitable for 11 KV cable (cable entry from bottom/ top/side) end termination with heat shrinkable jointing material etc. as required. (Note- Cost of end termination not included in this item)(a) Incoming – ½ No 800Amp. VCB(b) 1* No. – 11 KV / 110 Volts PT Class 0.5 accuracy and 100 VA burder with 1 No. Voltmeter (0-15KV), analog/digital* type, selector switch for voltmeter and protection fuses/MCB for HT metering upto 12 KV on incomer.(c) 1* No. – (0-100 A) dual scale Ammeter, analog/digital* type, selector switches for ammeters.(d) 1* No. – Microprocessor based numerical relay with O/L, E/F and S/C protection.(e)1* No. – Set of dual core dual ratio 3 CTs 300/150/5/5 A of 15 VA burden and accuracy Class – 0.5 for metering and class 5P10 for protection.(a) Outgoing – 2Nos. 800Amp. VCB(b) 2Nos. – (0-100 A) Ammeters, dual scale analog/digital* type & selector switches for Ammeters.(c) 2 Nos. – Microprocessor based numerical relays with O/L, E/F & S/C protections.(d) 2 Nos. – Setofdualcoredualratio3CTs 100/ 50/5/5 A of 15 VA burden and accuracy Class-1.0 for metering and class 5P10 for protection.1. Supply of power pack 24 volts complete with battery and charging device.
451	Supply of 50 Sq.mm size XLPE cable from 11 K.V.UPPCL metering panel to 11 KV incoming H.T. switch gear panel and panel to transformer.
452	Supplying of 250 KVA or more rating suitable for site requirement, 11/0.415 KV, 3 Phase, 50 Hz, Dyn 11, outdoor ONAN type, copper wound transformer with OFF load tap changing arrangement on HV side in steps of2.5% with range+ 7.5% to -7.5%, having cable end boxes on HV side suitable for 3x150sqmm XLPE cable of 33 KV grade and bus trunking arrangement on LV side complete with all accessories i/c first filling of filtered dehydrated oil and confirming to IS 1180 & as per specification attached complete in all respects as required at site.
453	Supplying of cubicall type LT panel suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized (preferably) design from CRCA sheet steel of 2 mm thick for framework and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having 630Amp capacity extensible type TPN aluminium alloy bus bars of hight conductivity, DMC / SMC bus bars of high conductivity, DMC/ SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., bottom base channel of MS section not less than100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth barof size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from mainbus bar to switch gears with required size of Al. bus bars and control wiring with 50sq. mm. PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c providing following switch gears :-(I) Incoming : 2 Nos 630 Amps horizontal drawout type air circui+B12t breaker of fault breaking capacity 50 KA (Ics=Icu upto433 V manually operated, fitted with interlocked door, automatic safety shutters, mechanical ON/ OFF and service/test/isolated position indicators and frame earthing contact, conforming to IS 1397- 2 : 1993 as amended up-to-date complete with following accessories for each MCCB.(a) Independent manual spring closing mechanism- 1 No.B10(b) Microprocessor release (EMI & EMC certified) for over current, earth fault & short circuit protection- 1 set.(c) Analog 96 mm square flush pattern /Digital* type Voltmeter (0-500 V), with selector switch & back up HRC fuses/ MCBs-1 set.(d) Analog 96 mm. square flush pattern/ Digital* type Ammeter (0-630Amp), with selector switch and one set of 3 nos. CT’s of ratio10/5A Class I accuracy and 15 VA burden- 1set. (e) 3 Nos. Phase indication LED lamps with2 Amp back up HRC fuse, breaker ‘ON’ indicating light with 2 A HRC fuse, test terminal block set, fuses, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required.(f) Shunt trip coil 220 V A.C.(II) Bus Couplers :2 Nos. 630Amps drawout type, air circuit breakers offault breaking capacity 50 KA (Ics=Icu upto433 V) manually operated, with interlocked door, automatic safety shutters, mechanical ON/OFF and service/test/isolated position indicators and frame earthing contact conforming to IS 13947- 2 : 1993 as amended upto date complete with following accessories for each ACB:(a) Independent manual spring closing mechanism- 1 No.(b) Breaker ‘ON’ indicating light with back up 2 A HRC fuse test terminal block, fuses, circuits contactors for positive electrical interlocking of breakers, etc. as required- 1 set.(III) Bus Bars :TPN aluminium bus bars of minimum of 630Amps capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bar cross section, size supports & their spacing etc. for withstanding fault level of 31 MVA for 1 Sec.(IV) Interlocking :Electrical through advance contacts in ACB’s (incomers & bus couplers) and mech- anical (castel key) interlocking should beprovided to ensure that only one supply is available at a time on each section of bus and to eliminate any possiblility of accidentally approaching two supplies at one bus section.(V) Outgoing :(a) 02 Nos. 630Amp 4 Pole ACB (Ics = kA upto 433 V)/SFU with HRC fuse (BC : 80 kA)(b) CT’s of ratio 10/5Amps 4Nos.4Set (1 set of 2 Nos.)(c) Analog 96 mmsq/Digital* type ammeter (0-100Amp) with selector switch set.
454	Supply and laying of 650/1100 volt grade 240sq mm 3½ core PVC Armoured Aluminium cable from transformer to L.Tpanel and from outgoing panel to distribution panel (1x3½x240 sq mm)
455	Making Earth pit for earthing complete in all respect. Earthing system shall executed as per IS:3043 and I.E. rules.
456	Installation and commissioning of 11 KV/0.4 KV substations including HT Panels and L.T. main control panel including all labor T&P complete in all respect.
457	Supply and making of indoor cable end termination joint kit of size 70 sq mm 3 core for 11 KV H.T. XLPE cable
458	Provision for routine testing of equipments such as transformer, HT Panels and main LT Panel at manufacturer’s works.
459	NOC from Electrical safety department for all field installations such as pumping plants, substation etc.
460	PUMPING PLANT AND ACCESSORIES FOR ZONE-3 OF MCWR
461	Supply of Vertical type self-waterlubricated statically, dynamically, hydraulically balanced turbine pumpcapable of discharging at thefollowingdutyconditionasgivenbelowduetoallcauseswith surface discharge head confirming to IS:1710 and as amended as on date with accessories as per IS 5120/1977(Reconfirmed 2011) and as amendedthereaftertosuitthesitecondition.ThePumpBowlassembly and casing shall be CI IS 210 FG: 260 with suitable coating inside casing of 500 DFT, suitable for protection against corroision,erosion and prevent oxidation.Impeller and Wearing / Neckringshall be Duplex stainless steel CD4MCu (Chromium-24.5% minimum,Carbon < 0.04% ) as per ASTM A890 GrlA or DIN 1.4474-EN 10088, Hardness 220-260 BHN,pump shaft-Stainless steel AISI 410, pumps and line shaft sleeve - stainless steel with ceremic coating 700 BHN,Strainer-SS 304,coupling between pump ang motor - Flexible pin bush type and bearings shall be Anti friction L-10 with 60000 Hrs life at 1450 rpm.06mtr/suitablelengthcolumnassembly, with vertical hollow shaft. Squirrel cage induction motor(IS:126152011/IEC60034-1)suitablefortheabovepump continuous rated TEFC IP-55 with Class \"F\" insulation for operation in AC, three Phase/50 HZ (±5%), 415V (±10%), running with a speed of pump. Capacity as follows :-
462	900 LPM / 36 Mtr. HEAD / 15 HP MOTOR (1w+1s)Head & discharge may increase as per site requirement
463	MAIN PIPING AND VALVES :-Supply of 100mm Main piping & valves complete of suitable size and quantity required for delivery side, bye pass arrangement and 100mm common Header upto 1 m. outsidethe pump house along with 100 x 100 x 100 mm A/F Tee (2Nos), 100 mm bend (01 Nos), 100 mm blind flange (01 Nos), D/F Pipes suitable sizeall necessary nuts, bolts, rubber packing, M.S Support for pipe,mechanical joints (03 Nos) and valve etc. complete in all respect as per site conditions. Note - Suitable Sizeof Delivery line of each pumping plant and common header it may increase as per site conditions with best engineering manner
464	Motor operated actuator with sluice valve :- Supply of DI/DF sluice valve withElectrically integrated actuater (Totally enclosed,weather-proofanddustproofconstructionwithIP-67, protectionclass suitable for installationin any positionwithout lubrication,leakageorotheroperationaldifficultywithspecialgrease filledgearboxandsuitableformanualoperationforemergencywhich will automatically dis-engage on restoration of power to motor and with10wattsingle phase spaceheaterandcontinuouslocalmechanical positionindicatorandindividuallyreplaceablecountergearassembly and with two torque and four limit switches with S.S. flap and operated withgeardrivencamsandofrating250Volt,5Amp,AC/DC,torque switch dialand with TEFC squirrel cageinduction) operatedsuitable to SCADAoperationsluicevalvehavingbodydoorcoverof gradedincast irontoIS:210Gr.Fg.260bodyanddoorringsofSSASTMA743Gr.CF8 andbearingblockofleadedtinbronzetoIS:318Gr.LTB2hingepinof stainlesssteelAISI:431.ValvesgenerallyconformtoIS:5312.Flangesto bedrilledasperIS:1538Part-IV&VI. Valves aresuitable for hydrostatictestpressureof10Kg./Cm2 forseatand15Kg./Cm2for body(PN-1.0)of following sizes
465	Actuator with Sluice Valve of size :- 100mm or more size suitable for pumps
466	Actuator with Sluice Valve of size :- 100mm or more size suitable for common header
467	Non return valve :- Supply of DI/DF Single Door/ Multi Door Non return/reflux valve conforming to IS:5312/2003(partI & II) PN-1.0 to be fixed after pumps for 90% fast closing & 10% slow closing .
468	100 mm Dia or more size suitable for pumps and common header
469	CE/UL Certified Electromagnetic flow meter :- SupplyofCE/ULFullBorecElectromagneticFlowMeterofapproved make of following dia and specifications complete: Media : Water (Raw/ Chlorinated), Pressure:upto1.0 MPa,Processtemp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI316L/ HastelloyC276/ Tantalum, Lining Material : Hard Rubber/ Neoprene/ Poly-urethane(PU), Flange: SS /CS, FlangeStandard & Rating : ANSI 150, Coil housing : SS AISI 304/ Carbon Steel/ Die Càst Aluminium,with anticorrosivepaint&providecompletely sealed (leak proof) constructionasperrequirement‘ofIEC 60529, Accuracy : + 0.5 % M.V. velocity0.3to10m/s,Transmitter/signaconvertor Enclosure :Die CastAluminium, Power Supply: 80-240 V AC-5OHz,Output1: 4-20 mA,Output2:Pulse,CommunicationOutput:RS485/Heart, Display Type : LCD/ LED Display, Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibration and configuration parametersand totalizer value during power failure, Protection category- IP 68for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, cable.
470	Size 100mm or more size suitable for common header
471	ELECTRICAL ITEMS:-
472	Supply& laying of 1.1KV grade XLPE insulated armoud multi strand copper conductor cable of 3C x 6 sq.mmfrom control Panel to respective Motors with lugs etc. (copperconductor should be electrlytic grade copper, purity >99.97% ISI marked asper IS:1554 P-I / IS :7098 P I)
473	MOTOR CONTROL CENTER (MCC) PANEL :-Single front, Indoor & floor mounted,cubical type Panel factory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shrouds and Gland Plate-3 mm thick) CRCA sheet duly power coateddust and vermin proof IP-54 /IS:2147, considered Earth Bus-Bar-GI Strip compitableto SCADA operation with RS485 Port consisting ofINCOMMING SECTION100A,50KA,TPN,MCCB microprocessorbaseed (O/C,S/C)release-2 No with suitable rating auto phase reversal unit, Spreader Links & Extended ROH for - 1 No, 3 Phase Digital MultifunctionMeter -1No,DigitalVoltmeter0-500V -1No,Digital Ammeter 0-400A- 1 Nos, CT For meter Resin Cast CL-1400A/5A,15VA - 3 Nos, Phase indication light LED type 220V AC - 1 Set, Control MCB SP 6A ,10KA ABB - 3 Nos, CT Shorting Terminal - 4 Nos, Neutral Link - 1 No.OUTGOING SECTION63A, 50KA, TPN, MCCBmicroprocessorbased (O/C,S/C) RELEASE - 3 No(1w+1s+1 Spare), SpreaderLinks &Extended ROH for MCCB- 3 Nos., 63A TPN MCCB 35KA- 2 Nos. Terminal 63A
474	Supply of Air Cooled Digital soft starter suitable for the LT motor offered for operation in AC three Phase 50Hz (+/- 5%), 415V(+/-10%) including linecontactorssuitablefornextstandardhigherKWrating,Over& Underloadprotection,shortcircuit&singlephasingprotectionwith frequency meter, Ammeter, Voltmeter, indicating lamp 6Nos, LED ON/OFF type and Start /Stop push button and Instrument Fuses, suitable to SCADA operation with RS485 Port rating capacity 15 KWfor 15 hp motor
475	Supply of microprocessor based three phase sensing power factor correctionrelaypanel,IEC/EN61000-6-(2&4)having3CTsensing, sensitivity up to 50 milli amp secondary current , self analysing auto c/k settingaccordingtotargetedpowerfactorsetting,therelayshallhave digit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with RS 485, indication of switching on units, auto/manual status, and shall have overloadprotection,novoltrelease,havingmultiparameterlikeKW, KVA, KVAR rating capacity of 13 KVAR or more as per requirements
476	CE/UL Certified Pressure transmitter for pumps and common header:- Supply of CE/UL Certified pressure transmitter CE markd with following technical parameters and Interfacing with PLC panel includingmounting arrangement. Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDAccuracy - +/- 0.1 % of full scale or better Enclosure- IP 68
477	Earthingwithcopperearthplate600mmX600mmX3mmthick including accessories, and providing masonry enclosure with cover plate havinglockingarrangementandwateringpipeof2.7metrelongetc. with charcoal/ coke and salt as required according to latest IS:3043 Supplyingandlaying50mmX6mmG.I. stripat0.50metrebelow groundas stripearth electrode, including connection/ terminatingwith nut,bolt,spring,washeretc.asrequired.(Jointingshallbedoneby overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)( 01 job = seprate Double Earthing of each pumping plant and its pannel as per IER )
478	Installation of all equipments, power wiring of Electrical equipments and commissioning of the pumping plants.
479	RubbermatsforelectricalpurposeasperIS:5424-1969, plain/chequered (1mX2m) - 10mm thickness
480	Cable trench Chequerred plate
481	Automation For Intake Well
482	CE & UL Certified PLC/RTU with redudant CPU & Power supply in IP 54 enclosure suitable to Communicate with GSM based modem unit with redudant CPU & Power Supply with analog & digital parameter & features as specified for each ZPS/OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations with control panel as specified in tender technical specification.
483	GSM / GPRS based wireless communication with 4G modem for RTU/PLC Capable to transfer & gather data from remote sites to control stations all accessories including with signal enhancer antanna made for pumping plant internet charges as specified in tender technical specification.
484	CE/UL Certified Intelligent energy meters
485	CE/UL Certifiedthree phase Surge protector for control panel at main switch
486	CE/UL Certified 7\" touch screen suitable for communication with PLC/RTU for local display & control of process parameters.
487	Control Panel with IP-54 Protection, industrial grade for all equipment. Separate for control (24V) and power equipments
488	Cable
489	(i) Complete cabling upto 3 Pumps
490	Security Survelliance IP Camera with recorder (optional)
491	Installation, commissioning & testing
492	Local Control Station at WTP
493	CE/UL & BIS Certified industrial grade LED Monitor with latest configuration as per specification
494	Desktop / PC with i5/i7 processor for as per technical bid documents
495	CE/UL Certified 5KVA UPS with batteries as per technical bid documents
496	Full development version of required TAGS SCADA Software with customization of software for LCS as per requirement as per spec. mentioned in technical bid documents.
497	CE/UL certified local control room PLC with redundant CPU & power supply at LCS in IP 54 enclouser as per spec. mentioned in technical bid documents.
498	GSM based wireless/Broadband/Equivalent communication system for PLC capable to transfer & received data & gather from remote sites to control station, all accessories included signal enhancer anternna along with running expenses till DLP
499	CE/UL Certified firewall for network protection
500	SURGE PROTECTOR FOR ETHERNET communication protection.
501	CE/UL certified industrial grade Ethernet Swtich
502	Cannon/HP or equivalent Laser printer 1018 or equivalent
503	Security Survillance IP Camera with recorder (Optional)
504	Installation, Commissioning & testing including required furniture, A/C etc.
505	AUTOMATION FOR MCWR
506	CE & UL Certified PLC/RTU with redudant CPU & Power supply in IP 54 enclosure suitable to Communicate with GSM based modem unit with redudant CPU & Power Supply with analog & digital parameter & features as specified for each ZPS/OHT to store and transmit data on GSM backbone, RTU/PLC designed with logic to transfer data at multiple stations with control panel as specified in tender technical specification.
507	GSM / GPRS based wireless communication with 4G modem for RTU/PLC Capable to transfer & gather data from remote sites to control stations all accessories including with signal enhancer antanna made for pumping plant internet charges as specified in tender technical specification.
508	CE/UL Certified Intelligent energy meters
509	CE/UL Certified three phase Surge protector for control panel at main switch
510	CE/UL Certified 7\" touch screen suitable for communication with PLC/RTU for local display & control of process parameters.
511	Control Panel with IP-54 Protection, industrial grade for all equipment. Separate for control (24V) and power equipments
512	Turbidity Analyzer at MCWR
513	PH Analyzer
514	Chlorine Analyzer
515	Cable
516	(i) Complete cabling upto 3 Pumps
517	Security Survelliance IP Camera with recorder (optional)
518	Installation, commissioning & testing
519	ESTIMATE FOR AUTOMATION OF EXISTING STORAGE / HILLOCK /CWR ( 450 KL+350KL=800 KL )AGAINST ZONE-1
520	ESTIMATE FOR AUTOMATION OF EXISTING STORAGE / HILLOCK /CWR ( 450 KL+350KL=800 KL )AGAINST ZONE-1
521	CE/UL Certified level transmitter for CWR / HILLOCK :- Supply of Radartype leveltransmitter with battery powerCEmarkedwith following technical parameters and Interfacing with PLC panel including mounting arrangement.Output-4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68
522	CE/UL Certified Electromagnetic flow meter at CWR / HILLOCK outlet :- SupplyofCE/ULFullBorec ElectromagneticFlowMeterofapproved make with battary power for remote placesof following dia and specificationscomplete:Media: Water (Raw/ Chlorinated), Pressure:upto1.0 MPa,Processtemp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI316L/ HastelloyC276/ Tantalum, Lining Material : Hard Rubber/ Neoprene/ Poly-urethane(PU), Flange: SS /CS, FlangeStandard & Rating : ANSI 150, Coil housing : SS AISI 304/ Carbon Steel/ Die Càst Aluminium,with anticorrosivepaint&providecompletely sealed (leak proof) constructionasperrequirement‘ofIEC 60529, Accuracy : + 0.5 % M.V. velocity0.3to10m/s,Transmitter/signaconvertor Enclosure :Die CastAluminium, Power Supply: 80-240 V AC-5OHz,Output1: 4-20 mA,Output2:Pulse,CommunicationOutput:RS485/Heart, Display Type : LCD/ LED Display, Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibration and configuration parametersand totalizer value during power failure, Protection category- IP 68for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, cable and also interfacing with PLC panel.
523	300 mm dia
524	CE/UL Certified Pressure transmitter at CWR / HILLOCK outlet :- Supply of CE/UL Certified pressure transmitter CE markd with battary power following technical parameters and Interfacing with PLC panel includingmounting arrangement. Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDAccuracy - +/- 0.1 % of full scale or better Enclosure- IP 68
525	Residual chlorine analyser / meter :-Supply of RCA with battary power must have automatic sensor cleaning facility at pure water sump and Interfacing with PLC panel. Residual Chlorine meter shall comprises of 3 components i.e. sensors, flow through assembly and transmitter with indicator andgives 2 outputs one to Local display & other to PLC including Mounting arrangement.Overall Range : 0 - 8 mg/l (ppm)Accuracy : 2% of full scaleSupply Voltage : 230 V acOutput : 4-20 mAMembrane free sensor of 2 gold plated electrodes for long term stability and reference electrode (ag/Agcl) must beprovided to avoid maintenance. IP 65 Nema 4 housing protection class required.
526	Installation , cabling of CWR/HILLOCK including all power and control cable of all equipmentsand commissioning complete in all respect.
527	CE/UL Certified 5KVA UPS with batteries as per technical bid documents
528	ESTIMATE FOR AUTOMATION OF PROPOSED OHT ( 1000 KL ) AGAINST ZONE-2
529	Motor operated actuator without sluice valve at OHT outlet :- Supply of DI/DF Electrically integrated actuater (Totally enclosed,weather-proofanddustproofconstructionwithIP-67, protectionclass suitable for installationin any positionwithout lubrication,leakageorotheroperationaldifficultywithspecialgrease filledgearboxandsuitableformanualoperationforemergencywhich will automatically dis-engage on restoration of power to motor and with10wattsingle phase spaceheaterandcontinuouslocalmechanical positionindicatorandindividuallyreplaceablecountergearassembly and with two torque and four limit switches with S.S. flap and operated withgeardrivencamsandofrating250Volt,5Amp,AC/DC,torque switch dialand with TEFC squirrel cageinduction) operatedsuitable to SCADAoperationsluicevalvehavingbodydoorcoverof gradedincast irontoIS:210Gr.Fg.260bodyanddoorringsofSSASTMA743Gr.CF8 andbearingblockofleadedtinbronzetoIS:318Gr.LTB2hingepinof stainlesssteelAISI:431.ValvesgenerallyconformtoIS:5312.Flangesto bedrilledasperIS:1538Part-IV&VI. Valves aresuitable for hydrostatictestpressureof10Kg./Cm2 forseatand15Kg./Cm2for body(PN-1.0)of following sizes
530	400 mm dia
531	CE/UL Certified level transmitter for OHT :- Supply of Radartype leveltransmitter with battary powerCEmarkedwith following technical parameters and Interfacing with PLC panel including mounting arrangement.Output-4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68
532	CE/UL Certified Electromagnetic flow meter :- SupplyofCE/ULFullBorecElectromagneticFlowMeterofapproved make of following dia and specifications complete: Media : Water (Raw/ Chlorinated), Pressure:upto1.0 MPa,Processtemp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI316L/ HastelloyC276/ Tantalum, Lining Material : Hard Rubber/ Neoprene/ Poly-urethane(PU), Flange: SS /CS, FlangeStandard & Rating : ANSI 150, Coil housing : SS AISI 304/ Carbon Steel/ Die Càst Aluminium,with anticorrosivepaint&providecompletely sealed (leak proof) constructionasperrequirement‘ofIEC 60529, Accuracy : + 0.5 % M.V. velocity0.3to10m/s,Transmitter/signaconvertor Enclosure :Die CastAluminium, Power Supply: 80-240 V AC-5OHz,Output1: 4-20 mA,Output2:Pulse,CommunicationOutput:RS485/Heart, Display Type : LCD/ LED Display, Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibration and configuration parametersand totalizer value during power failure, Protection category- IP 68for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, cable.
533	400 mm dia
534	CE/UL Certified Pressure transmitter at OHT outlet :- Supply of CE/UL Certified pressure transmitter CE markd with following technical parameters and Interfacing with PLC panel includingmounting arrangement. Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDAccuracy - +/- 0.1 % of full scale or better Enclosure- IP 68
535	Residual chlorine analyser / meter :- Supply of RCA must have automatic sensor cleaning facility at pure water sump and Interfacing with PLC panel. Residual Chlorine meter shall comprises of 3 components i.e. sensors, flow through assembly and transmitter with indicator andgives 2 outputs one to Local display & other to PLC including Mounting arrangement.Overall Range : 0 - 8 mg/l (ppm)Accuracy : 2% of full scaleSupply Voltage : 230 V acOutput : 4-20 mAMembrane free sensor of 2 gold plated electrodes for long term stability and reference electrode (ag/Agcl) must beprovided to avoid maintenance. IP 65 Nema 4 housing protection class required.
536	Installation , cabling of CWR including all power and control cable of all equipmentsand commissioning complete in all respect.
537	ESTIMATE FOR AUTOMATION OF PROPOSED OHT ( 350 KL ) AGAINST ZONE-3
538	Motor operated actuator without sluice valve at OHT outlet :- Supply of DI/DF Electrically integrated actuater (Totally enclosed,weather-proofanddustproofconstructionwithIP-67, protectionclass suitable for installationin any positionwithout lubrication,leakageorotheroperationaldifficultywithspecialgrease filledgearboxandsuitableformanualoperationforemergencywhich will automatically dis-engage on restoration of power to motor and with10wattsingle phase spaceheaterandcontinuouslocalmechanical positionindicatorandindividuallyreplaceablecountergearassembly and with two torque and four limit switches with S.S. flap and operated withgeardrivencamsandofrating250Volt,5Amp,AC/DC,torque switch dialand with TEFC squirrel cageinduction) operatedsuitable to SCADAoperationsluicevalvehavingbodydoorcoverof gradedincast irontoIS:210Gr.Fg.260bodyanddoorringsofSSASTMA743Gr.CF8 andbearingblockofleadedtinbronzetoIS:318Gr.LTB2hingepinof stainlesssteelAISI:431.ValvesgenerallyconformtoIS:5312.Flangesto bedrilledasperIS:1538Part-IV&VI. Valves aresuitable for hydrostatictestpressureof10Kg./Cm2 forseatand15Kg./Cm2for body(PN-1.0)of following sizes
539	300 mm dia
540	CE/UL Certified level transmitter for OHT :- Supply of Radartype leveltransmitter with battary powerCEmarkedwith following technical parameters and Interfacing with PLC panel including mounting arrangement.Output-4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68
541	CE/UL Certified Electromagnetic flow meter :- SupplyofCE/ULFullBorecElectromagneticFlowMeterofapproved make of following dia and specifications complete: Media : Water (Raw/ Chlorinated), Pressure:upto1.0 MPa,Processtemp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI316L/ HastelloyC276/ Tantalum, Lining Material : Hard Rubber/ Neoprene/ Poly-urethane(PU), Flange: SS /CS, FlangeStandard & Rating : ANSI 150, Coil housing : SS AISI 304/ Carbon Steel/ Die Càst Aluminium,with anticorrosivepaint&providecompletely sealed (leak proof) constructionasperrequirement‘ofIEC 60529, Accuracy : + 0.5 % M.V. velocity0.3to10m/s,Transmitter/signaconvertor Enclosure :Die CastAluminium, Power Supply: 80-240 V AC-5OHz,Output1: 4-20 mA,Output2:Pulse,CommunicationOutput:RS485/Heart, Display Type : LCD/ LED Display, Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibration and configuration parametersand totalizer value during power failure, Protection category- IP 68for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, cable.
542	300 mm dia
543	CE/UL Certified Pressure transmitter at OHT outlet :- Supply of CE/UL Certified pressure transmitter CE markd with following technical parameters and Interfacing with PLC panel includingmounting arrangement. Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4\" LEDAccuracy - +/- 0.1 % of full scale or better Enclosure- IP 68
544	Residual chlorine analyser / meter :- Supply of RCA must have automatic sensor cleaning facility at pure water sump and Interfacing with PLC panel. Residual Chlorine meter shall comprises of 3 components i.e. sensors, flow through assembly and transmitter with indicator andgives 2 outputs one to Local display & other to PLC including Mounting arrangement.Overall Range : 0 - 8 mg/l (ppm)Accuracy : 2% of full scaleSupply Voltage : 230 V acOutput : 4-20 mAMembrane free sensor of 2 gold plated electrodes for long term stability and reference electrode (ag/Agcl) must beprovided to avoid maintenance. IP 65 Nema 4 housing protection class required.
545	CE/UL Certified 5KVA UPS with batteries as per technical bid documents
546	Installation , cabling of CWR including all power and control cable of all equipmentsand commissioning complete in all respect.
547	03 Months trial & run withoutelectricity includingoperation and chemical charges (PAC) for 9 MLD and 02 nos chowkidar/months for watchward , 02 nos Technician/months and 04 nos SCADA operators/months for LCS .

Also Visit

Tenders

Uttar Pradesh Tenders

Construction Tenders

Drainage Work Tenders

Drainage Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Kulpahar Nagar Panchayat Reorganization Water Supply Scheme Distt.Mahoba Under Amrut 2.0 - Civil Works 2 Wtp Works 3 Survey, Investigation, Soil Testing, Planning, Design And Drawing Construction, Commissioning Etc. As Per Design And Drawin, Mahoba-Uttar Pradesh

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Kulpahar Nagar Panchayat Reorganization Water Supply Scheme Distt.Mahoba Under Amrut 2.0 - Civil Works 2 Wtp Works 3 Survey, Investigation, Soil Testing, Planning, Design And Drawing Construction, Commissioning Etc. As Per Design And Drawin, Mahoba-Uttar Pradesh

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us