Beautification of Town Kulgam under Head FC Grants- 1 Sitting Benches (12 No.s) 2 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 3 Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains,pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspitsand the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:All kinds of soil : 4 Providing and laying stoneNalla Boulders (duly hand packed) incld: dressing and ramming including all carriages complete. 5 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)incld: all carriages 6 Providing and placing 3 Seater cast iron Bench with arm rest 5 feet long with back support as per directions of Engineer Incharge using MS tubes and angle iron 7 Selfie Point 8 Surface dressing of the ground including removing vegetation and in-equalitiesnot exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil. 9 Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains,pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspitsand the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:All kinds of soil : 10 Providing and layingspreading and compacting of stone soling, hand packed, of specifiedsize in uniform thickness , rolling , watering including carriage of same from approved source upto site of work complete. 11 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)incld: all carriages 12 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) incld all carriage 13 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 14 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. Allworks upto plinth level 1 : 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) incld all carriage. 15 Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete. 16 Reinforcement for RCC works including straightening , cutting, bending, binding & placing in positionall complete TMT reinforcement of grade Fe-500D steel bars at all levels. 17 Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels 16mm over 0.5mm 18 Providing Edge Moulding to 16mm thick marble stone counters, vanities etc incld: machine polishing to edge to give high gloss finish etc complete 19 Supply and Installtion of illuminated 3D alphabets made of stainless steel grade 304 having size of 900mm height as per the design covered and sealed with arcylic 3mm sheet in milky white colour to illuminate from front side. From back side it should be with 4mm thick ACP to make it strengthen and hold the entire weight in vertical position .LED Module made out of heavy duty from Samsung duly cleaned and finished modulewith night visibility with glossy finish is wired with all electrical accessories incld: 300k delivery 100 lumnes per watt package KULGAM considering as a single word in one go. The total length would be approx. 20-22 feet with 3 feet height along with mounting on the ground /stone with resin and SS fastner as per directions of Engineer in charge. 20 Sign Board (08 No.s) 21 Supply and Fixing of Retro Reflective Double Sided Over Head Gantry Signage made out of Type-XI Micro Prismatic Type sheeting conforming to IRC:67:2012 & ASTM D 4956-09, covered with Electro Cuttable translucent film as per the drawing and display matter given by the engineer in charge, fixed over 4 mm thick aluminum composite panels and riveted using 6mm aluminium rivets to back support frame all round supported on a tubular gantry structure of 300 NB pipe with 6.3mm wall thickness as per the drawings attached. The MS tubular poles shall be painted with epoxy & minimum two coats of synthetic enamel paint. The Gantry sign boards shall be firmly fixed to the ground by means of properly designed foundation (as per the drawings) with M25 grade cement concrete. Installation work shall be as per relevant clauses of MORT&H specifications section 800 & IRC: 67:2012 complete in all respect. The rates shall include cost of design, fabrication, supply, transportation, local shifting, erection of signage structure using crane, all T&P, machine, material and labour required for proper completion of work as per the direction of Engineer. (Complete Job) As per Clause 22 of IRC 67-2012 22 Structural steel work in built up sections, tubular and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded (Ornamental Pole caste Iron Pole 6mm thickness & 200mm Dia of03 Meter Clear Height 23 Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded 24 Bolts , Nuts , Washers < clips etc 25 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete On steel work 26 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two olr more coats 27 Providing and fixing of ACP 4mm thick sheets . Providing and fixing of micro prismatic type XI sheeting as per IRC 67-2012 reflective of size including lettering and signs applicable 28 Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) includingdisposal of excavated earth lead upto 50meters and lift upto 1.5 m,as directed by Engineer-in-Charge.All kinds of soil : 29 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)incld: all carriages 30 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. Allworks upto plinth level 1 : 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) incld all carriage. 31 Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete. 32 Reinforcement for RCC works including straightening , cutting, bending, binding & placing in positionall complete TMT reinforcement of grade Fe-500D steel bars at all levels. 33 Face Lifiting 34 Dismantling dressed stone work ashlar face stone work, marble work or precast concrete work manually/by mechanical means including stacking of serviceable material and disposalof unserviceable material within 50 meters lead as per direction of Engineer-in-charge:In cement mortar 35 Engagement of Carpenters and albours for dismantling of existing front roof including stacking of all serviceabale material and disposal of unserviceable material 36 Carpenter 37 Labour 38 Engagement of Balcksmith with hlpers nd albours for dismantling of existing Eves boarding and raising of front G.I Block including stacking of all serviceabale material and disposal of unserviceable material 39 Balcksmith 40 Helper 41 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size) incld: all carriages 42 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo-Mechanically Treated bars of grade Fe-500D or more. 43 P/F Decorative ornamentalGrill Panells of required pattern etc with MS flats, tubes, squares or round bars incld. Priming and painting of approved steel primer complete as per directions of E I C. 44 Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.Welded 45 Providing and fixing of High Rib Powder Coated versatile sheet roofing 50mm thick including Nuts, Wsahers , bolts complete job including all taxes and carriage applicable upto desired height complete 46 Providing and fixing of Bison panells of 6mm thick incld. All fittings, fixtures complete. 47 Painting steel work with deluxe multi surface paint of required shade to give an even shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm of approved brand and manufacture 48 Providing and supply and fixing of 3M ornamental cast iron decorative polecast iron oranmental Grill 49 Supply, Installation, Testing and Commissioning of 3 Mtr ornamental decorative pole made of Galvanized steel fitted with cast iron embellishment polyurethane paint coatedas perspecification/ drawing (enclosed)Mayfair/Dwarka with the following specifications:- The pole shall look like as shown in the drawing. It shall have all similar features as shown in the enclosed drawing/picture. The Pole has 3 Mtr (3000mm) length. The pole shall have a provision of 4 No. bolts and inbuilt junction box for fixing MCB’s/Connector or cutouts with detachable window cover including their costs. It also includes Supplying and fixing of ornamental Cast iron and mild steel single arm bracket painted with anti-corrisive enemal paint as per design, of Mayfair/Dwarka or of equivalent make/design (as per enclosed drawing) and decorative ornamental translucent luminariehaving IP-65 protection including .The job also includes fixing and testing of 40W Led inside luminarie.Further the pole shall be got approved by the concerned engineering wing after providing a sample before execution of work and the test certificate to be provided by the manufacturer. 50 Earth work in excavation by manualmeans in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: 51 Providing and laying in position cement concreteincluding curing but excluding the cost of shuttering and centring with1:1.5:3 (1 cement, 1.5 Coarse sand, 3 Graded stone aggregate 20 mm nominal size). The dimensions of the block should be 2x2x2. 52 Steel reinforcement for R.C.C. work ready to use cut and bend rebars of approved make from factory/workshop to construction site including placing in position and binding all complete.Thermo-Mechanically Treated bars of grade Fe-500D or more with 62kg/cum. 53 S/L , testing and commissioning of PVC alluminium armoured cable650 V/1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date Amendments.Havell/Eq. standard makeas directed by engineer incharge andmaking end termination with brass compression gland and aluminium lugs of required size. 54 a) 25 sq.mm 4 core 55 b) 10 sq.mm 4 core 56 Providing of service connection and earthings to luminaire from the junction boxin 1.5 mmPVC insulated, multicolour copper wire (FRLSH) . Havells/Polycab/SSK/KEI. 57 Providingof earthing by way of digging 10 deep pit then embedding 2x2, 5mm thick copper plate connecting the plate with main panel board by 10 SWG copper wire with 1/2 dia. Full thread brass nut and bolt and washers. Refilling of pit with alternate layers of salt coal and earth. 58 Supply and installation of Spiral Earthing through 10 swg GI wire after driving in ground up to adepthof3 in the ground from the base of the pole. 59 Main Panel 60 Design, Fabrication, Supplying, Installation, Testing and Commissioning of following panel made out of 2mm thick M.S. sheet, , vermin and dust proof, Outdoor type with suitable size of angle iron legs grouted in the cement concrete., with lockable type hinged doors, duly painted with provision for fixing ofincomer MCCB,outgoing DP MCBS, sets of Aluminium Bus Bar of different rating. after taking Derating factor into account, and other allied accessories etc. as required. the panel to be fabricated from reputed firm duly approved by CPRI.as per approved design, size may vary as per site requirement) 61 Providing and fixing of following protection equipments and other allied accessories including connections, inter connections, with suitable size of PVC insulated copper conductor cable including earthing etc. as required. 62 INCOMING: 63 b)100 amp TPN MCCB35 KA including spreader links, (Adjustable thermal and Adjustable magnetic release ) Legrand/ Shinider/L&T/ABB make. 64 b) 4 No. of Aluminium Bus Bar of 200 Amp. 65 OUTGOING: 66 a) 63 amp TPN MCB 67 b)5-32 SPMCB 68 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting the concrete path wherever required,jointing etc.direct in groundincluding excavation and refilling the trench with soft excavated earth making the surface level but excluding sand cushioning and protective covering etc., complete as required. 69 63 mm dia (OD-63 mm & ID-51 mm nominal) 70 Table TOP 71 Scarifying the existing bituminous road surface to a depth of 50mm and disposal of scarified material within all lifts and lead upto 1 km (by mechanical means) 72 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. All works upto plinth levelincld. all carriages. 73 Extra for providing richer mixes at all floor levels. Note:- Excess/ less cement over the specified cement content used is payable/ recoverable separately. Providing M-30 grade concrete instead of M-25 grade BMC/RMC 74 Providing and fixing of heavy duty stone cobble (100mm x100mmx100mm) of any colour laid on 40mm thick bed mortar 1 : 4 and joining 10mm space between cobble stone wityh mortar and finishe with grey cement slurry, the surface should be cleaned afterwards etc all complete finished as per approved designand slope under instructions of Engineer Incharge 75 Reinforcement for RCC works including straightening , cutting, bending, binding & placing in positionall complete TMT reinforcement of grade Fe-500D steel bars at all levels.
