Quotation Invited for rates of different items in Ulitity Shifting work ofConstruction of H.L Bridge over Swarnrekha River in Sakchi to Mango Road including construction of Elevated Approaches towards Mango and Azad Basti in East Singhbhum District in the State of Jharkhand-Supplying of DI Pipe 900 mm dia K9 Centrifugally cast (Spun) ductile iron pressure pipes for water supply with socket and spigot ends conforming to IS 8329/2000 (latest revision) in standard length of class K-9 suitable for push on joint (Rubber gasket jointing ) with cement mortar lining for inside surface and outside zinc coating with bituminous paint. Along with one number of rubber gasket (EPDM as per IS : 5382/1985) for each length of pipe. Ends of each pipe along with the groove for the EPDM Gasket must be burr free. DI pipe conforming IS 8329 with bitumen as per annexure C of IS 9523 shall have factory applied centrifugal OPC cement (IS 8112) mortar lining inside as per the provision of appendix B of the IS 8329.DI Pipe should be procured from Tata Steel only 2 Carrying laying,installation and fixing of 900 mm nominal dia DI Pipe with hydro testing of pipe (water free). 3 Providing and laying DI Special of class K-12 suitable for push on jointing as per IS : 9523: 900 mm dia. (Work has to be executed without traffic Diversion by using suitable shoring whenever required) 4 Supply of hard barrication for laying pipe line 5 C/F hard baricades along the trench. 6 Earth work in excavation for laying DI Pipe 900 mm dia. Upto 1.5 mtr in any kind of soil including hard soil, un-consolidated filled up slag and slushy muck (Slope : 2:1) 7 Excavation from 1.5 m to 3 m in soft rock without blasting (Slope: 2:1) 8 Dismantling water bound macadam tar or Asphalt painted, including removing the debris with inintiallead of 50 meters. 9 Dismantling water bound macadamincluding removing the debris with inintiallead of 50 meters. 10 Dismantling Tar Sludge or Tar premixed Carpet or Asphalt premixed carpet, thickness upto 50 mm including removing the debris with in intial lead of 50 meters. 11 Supplyingand filling fine Aggregate, sand (proper watering with compaction after one layer. Layers shall not more than 150 mm depth). 12 Disposal of surplus soil/ earth upto 10 kM. 13 Provinding/supplying & installation at site ISI Mark ductile Iron manually operated Sluice valves of rating PN 1.0 with EPDM rubber gaskets, rubber sheet and MS nuts & bolts as per requirements, field testing and commissioning complete as per specification, including all cost of materials, providingflages joints two number, labour required, transportation up to site, loading, unloading & stacking etc. complete as per IS 14846 specification 900 mm dia. (Approved Make - VAG, L&T, kirloskar) 14 Construction of RCC walll chamber of 1.5 X 1.5 m inside including Top slab. 15 Inter connection of proposed pipeline with existing DI pipeline. 16 Local Transportaion of pipe. 17 Provision for Nallah crossing -3 Nos. 18 Dismantling before excavation temporary structures, grills, kerbs, poles, verges etc and restoring the same after pipe laying. 19 Misc Expenses. 20 Providing hard barricading with steel supports as mentioned in the standards upto 1.2m height at construction site CGI sheet. Reinforcement shall be used for structure and grouted into GL up to 300mm min and backfilled with excavated soil. Measurement shall be done in physical RM length. This item is to be operated upon specific approval from project in charges at Sr. Mgr level only and billing for the same is only to be done after showing photographs.(Double layers) 21 Charring & fixing hard barricading with steel supports as mentioned in the standards upto 1.2m height at construction site with CGI sheet. Reinforcement shall be used restructure and grouted into GL up to 300mm min and backfilled with excavated soil. Measurement shall be done in physical RM length. This item is to be operated upon specific approval from project in charges at Sr. Mgr level only and billing for the same is only to be done after showing photographs. 22 Levelling and dressing the ground including cutting, filling and compacting up to average above 75mm upto 200mm thickness as per requirement including all labourers, tools and plant complete as per specification and direction of the Engineer-in-charge. 23 Preparation of subgrade by rolling with vibratory roller 80-100 KN. Excavated bottom/existing top of embankment dressed to proper camber, profile, slope and density not less than 98% of the maximum dry density of soil as obtained by standard proctor test to receive granular sub-base. 24 Supplying and laying of granular sub-bases of required thickness conforming to Table 400-1/400-2 of MORTH specification as shown in the drawing & direction of engineer and rolled to 98% of maximum dry density of the material determined as per IS-2720 (Part8). The workmanship shall conform to clause 401 of MoRTH specification. (LD Slag free issue) 25 Supplying and laying of Wet Mix Macadam (WMM) course consist of improved quality crushed stone aggregates, granular materials conforming to physical and grading requirement as per Table 400-12 & 400-13 of MORTH specification, premixed in a mixing plant with controlled addition overwater, laying and spreading of mix uniformly to correct grade, slope, thickness, cross-fall, rolling, compacting with 80-100 KN vibratory roller, all as per drawing, specification and direction of the Engineer-in-charge with all materials, tools, plant and labour complete as per Section 406 of MORTH Specification. (LD Slag free issue) 26 Supplying and laying Dense Graded Bituminous Macadam (DBM) course of 80mm - 130mm finished thickness consist of approved quality crushed stone coarse agreegate, crushed stone fine agreegate rock dust filler conforming to physical and grading requirement as per clause 505, Table -500 8 & 9 of specification and added with bitumen binder forming composition of DBM layer as per Table 500-10 Grading -II of specification mixed in Hot Mix Plant, laying and spreading of mix uniformity to correct grade, slope, thickness and cross fall rolling, compacting with 80-100 KN power roller, all as per specification, drawings and direction of the Engineer-in-charge, all materials, tools, plant and labour complete. Thickness of DBM will be paid as per actuals observed at site on random basis by Core cutting/Thickness Gauge or as per Drg/Cross Section or as obtained from Pre & post levels, whichever is less. 27 Supplying and Laying of dry lean concrete (M10) grade and finishing, including necessary form work with all leads and lifts complete as per MORT&H specifications clause 602 and as per direction of Engineer-in-charge. 28 Supplying and laying of bituminous concrete (BC) 30mm to 45mm finished thickness as per section 500 Table 500-16 & 500-17 & 900-4 and clause 507 of MORTH specification grade II mixed in hot mix plant, laying and spreading of mix uniformly to correct grade, slope, thickness and crossfall, rolling, compacting with 80-100 KN power roller all as per specification, drawings and direction of the engineer, all materials, tools, plants and labour complete as per section 500 of Morth. Bitumen of(60/70) grade as per IS:73 shall be used. Thickness of BC will be paid as per actuals observed at site on random basis by core cutting/thickness gauge or as per drg/cross section or as obtained from pre & post levels, whichever is less. 29 Earthwork in excavation in all types of soil, moorum (hard, compact soft), rock, mica schist, quartz etc and fill materials like granulated lag, cinder, skulls, compacted slag or slag in mass etc. at depths as specified below in formation of road, drain, pits, guard wall etc required levels and grades and dressing complete as per the specifications and direction of the Engineer in both dry and wet conditions. 30 Supplying, laying & compacting plain cement concrete (M7.5) of following grade as defined by IS:456 with graded stone agreegates in all foundations, screenings etc at and at all heights and depths above and below finished road formation level, slopes all as per specifications and directions of the Engineer, all materials, tools, plant and labour complete. The rate includes all labour, tools & tackles, pipe scaffolding, platform complete, as directed by Engineer in-charge. Box drain PCC (M7.5). 31 Supply, laying & compacting plain cement concrete (M25) of following grade as defined by IS:456 with graded stone aggregates in all foundations, screenings etc at and at all heights and depths above and below finished road formation level, slopes all as per specifications and directions of the Engineer, all materials, tools, plant and labour complete. The rate includes all labour, tools & tackles, pipe scaffloding, platform complete, as directed by Engineer in-charge. Box Drain RCC (M25) 32 Box drain Reinforcement 33 Box drain Formwork 34 Misc. Expenses on item no. 20 to 33. 35 Providing and laying hot applied thermoplastic compound for Road Marking, lettering, arrows and any other signs as per IRC:35 as required 2.5mm thick including reflectorising glass beads @ 250 gms per Sqm. Area, thickness of 2.5 mm. 36 One coat water base paint with approve quality paint, surface preparation with approve quality primer. 37 Road Signage Board (Informatory Board) 38 Road Signage Board (Cautionary Board) 39 Road Signage Board (Mandatory Board) 40 Apply Prime Coat @ 1.00 Kg/Sqm. 41 Apply Tack Coat @ 0.3 Kg/Sqm. 42 Utility Corridor pipe laying and pipe cost with 300 dia NP3 43 Paver Block 1.5m width length 1Km @ Rs. 1572/- per Mtr. 44 Traffic diversion roadwork 45 Traffic diversion kerb work 46 Earthwork at Traffic diversion 47 Traffic diversion-water filled road barrier, 1 mtr long (repetitive) 48 Supply & fixing of 6/7 mtr long GI single armed Street light pole including integrated joint box, foundation bolt, required wiring & necessary civil works to be fixed at span of 25 mtr 49 Supply, fixing, testing & commissioning of following lights fixtures with ballast, lamps hanging arrangements in all respect.LED 90-watt street light fitting 50 Feeder Pilar for Street Light (Outdoor Type) incoming: - MCCB 32 A TPN 50KA 1 nos with overload, short circuit and earth fault protection.Outgoing: - RCBO 25A TPN 10KA: 3 Nos it should have fixing arrangement of multifunction meter & energy meter, stop provision at incomer. Control Voltage 110Vac including Timer & Contactor. 51 Supply Installation and testing of chemical earthing including earth pit (1 peg) for each feeder pilar. 52 Supply installation and testing of Spike earthing (for individual pole) 53 Supply of material & laying underground / floor / wall including making end termination and testing of following sizes of G.I. / Cu earthing conductor for loop earthing of equipment, switch boards & panels as required.25x6 Sqmm GI (for each feeder pilar) 54 Supply of material & laying underground / floor / wall including making end termination and testing of following sizes of G.I. / Cu earthing conductor for loop earthing of equipment, switch boards & panels as required.6 SWG GI Wire (for individual pole) 55 Supply, laying, testing commissioning 1.1 KV grade armoured XLPE /PVC sheathed, steel armoured, aluminium / copper conductor, power / control cables of following size direct in pole to pole.1 Run LT AB Cable 4C x 25 Sqmm + 1C x 25 Sqmm 56 Cable termination: Supplying and making of all materials for terminations of 1.1 KV grade copper / aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals.LT AB Cable 4C x 50 sqmm + 1C x 35 sqmm 57 Horizontal drilling across the road at 1 m depth with supply and erection of HDC/DWC pipe of suitable size. The thickness of HDC/ DWC pipe should be 4 milimetre. 4 inch dia 58 Removal of existing Highmast of 35 Mtr including dismantling through crane, transport to storage yard & storing. 59 Removal of existing Street light pole of 11 Mtr including transport to storage yard. 60 Cable Jointing : Supplying and making of all materials for Straight through jointing of copper / aluminium multicore cables of the following sizes. The work includes sizing the core leads, removing insulation, fixing suitable heat shrink jointing kit and insulating with M-Seal.11 KV 3 core x 300 Sqmm Aluminium armoured cable (A2XFY) 61 Supply of 132 Kv grade, single core, copper conductor, XLPE insulated FRLS type and of size 1C x 300 Sqmm laid buried underground where buried laid in depth of 1500mm including making of ncessary underground cable corridor i.e. excavation /backfilling and supply of material required such as sand, slab, bricks, good earth, clamps, caution tape, route marker etc. (Open Trench Method) (Approved make - Universal, PHELPS DODGE Thailand, BRUGG Switzerland) GTP has to be designed by supplier and subsequently got approved from Tata steel. Sample of GTP provided by Tata Steel for cable is attached for reference) 62 Supply of 132 KV grade, single core, copper conductor, XLPE insulated FRLS type and of size 1C x 300 Sqmm laid through HDD Method (Mechanized HDD Method)(Approved make - Universal, PHELPS DODGE Thailand, BRUGG Switzerland) GTP has to be designed by supplier and subsequently got approved from Tata steel. Sample of GTP provided by Tata Steel for cable is attached for reference) 63 Supply of Outdoor Termination kit suitable for 1Cx300sqmm 132 KV Cable for terminating (Approved Makes: PFISTERER/ABB KABELDON/NEXANS/RAYCHEM RPG (TYCO BRAND) (ALL IMPORTED) 64 Supply of 132 KV Straight through jointing kits for 1Cx300 sqmm 132KV cable (Approved Makes: PFISTERER/ABB KABELDON/NEXANS/RAYCHEM RPG (TYCO BRAND) (ALL IMPORTED) 65 Supply of 300 Sqmm Cu conductor, bonding cable & connector for 1Cx300 sqmm 132KV cable (Approved make - Universal, PHELPS DODGE Thailand, BRUGG Switzerland) GTP has to be designed by supplier and subsequently got approved from Tata steel. Sample of GTP provided by Tata Steel for cable is attached for reference) 66 Supply of 1 Phase Link Box with SVL ((Approved Makes:- ELPRO/ALSTOM/BHEL/JSI)) 67 Supply of 50 x 6 G.I. earthing conductor ((Approved Makes:- Universal)) 68 Supply of Lightning Arrestor 120 KV, 10 kA class III (Approved Makes ELPRO/CGL/ALSTOM/SIEMENS) 69 Providing & Commissioning of GI Supporting structure for all outdoor equipment (Scope includes supply, fabrication, galvanizing & painting of structural works for outdoor equipments such as 132 KV Tower, Termination Bushing, LA) Narrow tower D type plus 9 M of approved Makes of Tata/Jindal) 70 Supply, installation, testing & commissioning of Miscellaneous conductor, insulator, hardware, earth wire, yard outdoor lighting etc.(Approved Makes:- ELPRO/ALSTOM/BHEL/JSI) 71 Laying of 132 KV grade, single core, copper conductor, XLPE insulated FRLS type and of size 1C x 300 sqmm laid buried underground where buried laid in depth of 1500mm including making of necessary underground cable corridor i.e. excavation /backfilling and supply of material required such as sand, slab, bricks, good earth, clamps, caution tape, route marker etc. (Open trench method) 72 Laying of 132 KV grade, single core, copper conductor, XLPE insulated FRLS type and of size 1C x 300 sqmm laid through HDD method (Mechanized HDD Method) 73 Installation of Outdoor Termination kit suitable for 1Cx300sqmm 132 KV cable for terminating 74 Installation of 132 KV straight through jointing kits for 1CX300sqmm 132KV cable 75 Laying of 300 sqmm Cu conductor, bonding cable & connector for 1Cx300sqmm 132 KV Cable 76 Installation, Testing & Commissioning of 1 Phase Link Box with SVL 77 Laying underground / floor / wall including making end termination and testing of 50x6 G.I. earthing conductor. 78 Commissioning of GI supproting structure for all outdoor equipment (scope includes supply, fabrication, galvanizing & painting of structural works for outdoor equipments such as 132KV Tower, Termination Bushing, LA) 79 Installation, Testing and Commissioning of miscellaneous conductor, insulator, hardware, earth wire, yard outdoor lighting etc. 80 Construction of Joint Bay for 132 KV cable it includes excavation, PCC, sand bedding, brick wall, backfilling etc. 81 Earthwork excavation by mechanize up to 3.0 mtr. 82 Providing and laying PCC 1:3:6 at foundation 83 Providing and laying RCC-M-25 in foundation 84 Form work for all type of RCC structure 85 Supplying, fixing, cutting, bending TMT bar below 12 dia 86 Backfilling in all positions and heights 87 230 mm thick Brickwork providing brick masonry work using concrete brick of size 230x110x75mm size in cement mortar (1:6) including cost of conveyance, loading and unloading of all materials, laboures, watering & curing, sundries, etc. Complete as per drawing & the direction of Engineer-in-Charge 88 Fencing (with Hot Dipped G.I. chain link) 89 Supply and laying of 40mm gravel 90 Design Consultancy charges on landed supply cost of material 91 Storage Charges on landed supply cost of material 92 Transportation and Material handling Charges on landed supply cost of material 93 T and P Charges on landed supply cost of material 94 Testing and commissioning charges on landed cost of material 95 Finanace charges for BG and Securities Charges on landed supply cost of material 96 Project Management charges on landed supply cost of material 97 Contingencies charges on landed supply cost of material 98 Overhead chargeson landed supply cost of material 99 Add 18% GST : 100 Add 1% Labour Cess:
