Tender For Certain Provision Works In The Aor Of Age B/R-Ll Under Ge Kapurhtala.; 1 Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil all as specified and directed by Engr-in-charge. 2 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil all as specified and directed by Engr-in-charge. 3 Excavating over areas in soft/loose soil exc 1.5m deep and not exc 3.0 m deep and getting out complete all as specified. 4 M&L Plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified. 5 M&L Plain cement concrete (1:2:4) type B-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified. 6 M&L Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed by Engineer - in - Charge 7 M&L for plain cement concrete (1:5:10) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete and as in sub base of floors complete all as specified and directed by Engr-in-Charge. 8 Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out , returning filling in layers not exceeding 25cm including watering and ramming and removing surplus earth to a distance not exceeding 50 metre complete all as specified. 9 Use & waste fair finished flat surfaces Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc.; vertical or to better 10 M&L for reinforced cement concrete Design mix M-25 (20mm graded aggregates) in Walls, retaining walls, basement walls and the like; any thickness; above top of footings; including attached pilasters and buttresses 11 Form work to sides of concrete fdn footing base of columns and raft beams sides and soffits (if any) of fdn and plinth beams and similar wk vertical or to batter for rough finished surfaces. 12 Form work to sides of pillars, posts, struts, pier, columns square, rectangular or polygonal rough finished surface of concrete. 13 Form work to sides and soffits of floor or roof beams, beam haunching, lintel etc rough finished surfaces of concrete flats. 14 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; exceeding 200mm thick (Horizontal or sloping) all as specified and directed by Engr-in-charge. 15 RCC M-25 design mix as in fdn, including raft, fooling fdn beams, plinth beams bases for columns and mass concrete. 16 RCC M-25 design mix as in Plinth beams,Roof Beam, cantilivers, bressummers, lintel over 1.5m span all as specified and directed by Engr-in-charge.. 17 RCC M-25 design mix as in columns , pillars, piers, posts and struts etc. 18 M&L for RCC M-25 as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, Chhajja and in shelves and the like complete all as specified and directed by Engr-in-charge. 19 M&L for TMT bars (Fe 500),10 mm dia and over in reinforcement cut to length, bent to shape required incl bending spirally cranking, hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified. 20 M&L for TMT bars (Fe 500), 5mm dia and over upto incl 10mm dia stirrups bending spirally or hooping for columns, hooking ends and binding with mild sleet wire not less than 0.90mm dia complete all as specified and directed. 21 M&L for framed mild steel work of grade E-165 (Fe-290) as in framed work such as doors, gates or Flat iron frame work for drain covers etc,complete all as specified. 22 Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates of Fe-290 grade E-250 complete all as specified. 23 S&F of GI steel expended metal of size 25*25mm cut to length, bent to shape required and tying with and including annealed mild steel wire galvanized, steel staples and fixed to wood or steel members, weight not exceeding 4 Kilogram per square metre complete all as specified. 24 S&F for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250) quality B complete all as specified and directed by Engr-in-Charge. 25 S&F of Mild steel screw bolts 16mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5cm and n exc 30cm long complete all as specified and directed by Engr-in-Charge. 26 M&L for Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and as directed by Engineer-in-Charge. 27 M & L for Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and as directed by Engineer-in-Charge. 28 M&L for Old size Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified and directed by Engr-in-Charge. 29 M&L Brick work with sub class B burnt clay bricks (old size bricks) straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed by Engr-in-charge . 30 M&L for flush pointing to brick walls with CM 1:3 complete all as specified and directed by Engr-in-charge . 31 Providing cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in copings, kneelers, apex stones, bed plates etc including necessary form work complete. 32 Extra for forming fair finish to drain or channel of cement concrete, 30cm inner girth, using extra cement including forms moulds/mitered stopped ends etc. complete all as spd. 33 M&l for Pre-cast Reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in manhole covers , Drain Covers and set in cement mortar (1:4) including form work complete all as specified. (Reinforcement measured separately). 34 M&L painting with synthetic enamel paint two coats over a coat of red oxide primer including preparing the new untreated steel surfaces of any description over 10cm in width or girth. 35 M&L for Boring 300mm Dia holes 10m deep in any type of soil for under-reamed piles and getting out and disposal of spoil to a distance of n exc. 50 m Complete all as specified and directed.. 36 S&F of UPVC pipes (SCH-40) (Slotted) 150mm bore dia incl all necessary fitting Complete all as specified and directed.. 37 S&F of UPVC pipes (SCH-40) (Blind)150mm bore dia incl Plug Cap and all necessary fitting Complete all as specified and directed.. 38 M&L for filling 12.5mm Graded coarse aggregates in harvesting pit upto height 0.50m Complete all as specified and directed.. 39 M&L for filling 3mm to 5mm PEA Gravel in harvesting pit Complete all as specified and directed.. 40 M&L for filling Coarse Sand in harvesting pit upto height 0.50m Complete all as specified and directed.. 41 M&L for Rendering 15mm thick on fair faces brick surfaces in cement mortar 1 : 4 finished even and smooth without using extra cement including WPC @ 3% of wt of cement complete all as specified. 42 Ditto all as per item sl no 14 here-in-before but in cement mortar 1:6 complete all as specified and directed by Engr-in-charge. 43 M&L for Rendering 10mm thick on fair faces of concrete surfaces surfaces in cement mortar 1 : 3 as in ceiling finished even and smooth without using extra cement complete all as specified. 44 M&L for preparation of new plastered surfaces of walls and applying 2mm thick of Birla white putty to obtain the true line to achieve smooth surface and applying two coats of oil bound distermper complete all as specified and directed by Engr-in-Charge 45 M&L applying two coats of exterior emulsion (Apex) paint on newly plastered or unplastered wall surface over a coat of cement primer including preparation of surfaces, complete all as specified and as directed. 46 M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceiling and wall complete all as specified and directed by Engr-in-Charge 47 M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface under floor and plingh protection all as specified and directed by Engr-in-Charge. 48 M&L for 100mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) as in floor over hard core all as specified andm directed by Engr-in-charge. 49 M&L for 25mm thick plain Cement concrete type B-1, 1:2:4 (12.5mm graded aggregate) as on roof paddings and to receive tiles all as specified and directed by Engr-in-charge. 50 M&L 75mm thick PCC 1:3:6 type C2 as in plinth protection/hard standing finishing the surface even and smooth with out using extra cement 51 M&L for Anti-Termite Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area 52 M&L for Anti-termite Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface 53 M&L for Anti-termite Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area 54 M&L for 40mm thick in cement concrete Mortar 1:2:4 type B-0, Damp proof course to horizontal or vertical surfaces including necessary formwork all as specified and directed by Engr-in-charge. 55 M& L for Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m all as specified and directed. 56 M&L for Polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m all as specified and directed by Engr-in-charge. 57 Supply and fixing factory made uPVC white colour Two track two panels sliding glazed window upto 1.50m height made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) comprising of uPVC multi-chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 58 S&F 5.50mm thick Plain sheet glass, one side sheet glass is groundor obscured or frosted in squares exc 0.5 sqm each pane and glazing with metal beads all as specified. 59 M/L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but n.exc 0.18 Sqm in floor set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles, with 15 mm thick cement screed bed in CM (1:6) complete all as specified and directed by Engr-in-Charge 60 M&L for light shade Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed all as specified and directed by Engr-in-charge. 61 Ditto all as per item No 60 but in vertical surfaces over 10mm plaster all as specified. 62 S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. 63 Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge 64 Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 65 S & F Aluminium (die cast body) Door closer hydraulically regulated designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. 66 Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil all as spd. 67 Removal of excavated material (soil) to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5m above the starting point all as spd. 68 Preparation of newly plastered surface making surface completely dry and applying a coat of bitumen primer @ 0.40 ltr/sqm and after drying of primer apply APP modified water proofing membrane with non woven polyster reinforcement 3mm thick superior multipolymeric weighing not less than 3kg/sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyethylene (MHHDPE) film consisting of five layers with a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm under and over the APP membrane laid with torching application to the surface complete and sealing the side as well as end laps (overlaps should not be less than 10 cm) and applying two coats of aluminium paint above APP membrane surface , complete all as specified and directed. 69 Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. 70 M&L for Sand filing under floors or in foundations including watering and consolidation 71 M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658 - 2006 of 80mm thick ness, M-40 grade with grey cemet and pigment over sand cushioning complete all as specified. 72 Removing excavated material n exc.50M and depositing where directed at a level n exc1.5m above the starting point Note : (i) Excavated earth is used for area required earth filling. (ii) Charges of labour for earth filling is not given seperately it is considered in this item . 73 M&L Precast cement concrete block masonary with solid block (size 30x20x10 cm) as in edging ,type B1 1:2:4 (20 mm graded aggregate) exc 10 cm in width and setting in mortar 1:4 complete 74 M&L Reinforced concrete 300 mm dia pipe class NP-3 laid & jointed complete with collars, complete all as specified and directed. 75 Material and labour for point wiring complete with two 1.5 Sqmm single core multistranded copper conductor PVC (FR) insulated cable in PVC concealed conduit of size 19/20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 1.5 Sqmm insulated un-sheathed PVC insulated single core multistranded copper conductor common earth and connecting to earth dolly with suitable size of copper end connector for the following :- Note : (i) Colour code shall be maintained as per IE rule. 75.01 One light point controlled by one, one way switch 75.02 One fan point controlled by one, one way switch 75.03 One socket outlet 3 Pin, 5 Amp on independent board 75.04 One socket outlet 3 Pin, 5 Amp on same board. 76 M&L for point wiring with 4.00 Sq mm single core multi-stranded copper conductor PVC (FR) insulated, unsheathed cable 1100 volt grade in PVC concealed conduit of size 19/20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 4.0 Sq mm single core, multi-stranded copper conductor, PVC insulated, unsheathed cable for common earth and connecting for earth dolly for 5 pin, 15 Amp socket outlet on Independent board. 77 S&F switch piano flush type single pole one way 5 Amp (ISI Marked) Make - Legrand/Schnider/Havells 78 S&F switch piano flush type single pole one way 15 Amp (ISI Marked) Make - Legrand/Schnider/Havells 79 S&F socket out let 2 in 1, 3 pin 5 Amp flush type (ISI Marked) Make - Legrand/Schnider/Havells 80 S&F socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked ) Make - Legrand/Schnider/Havells 81 M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body (ISI Marked) Make - Legrand/Schnider/Havells 82 Supply, installation, testing and commissioning of 20 watt 4 ft long LED Batten housing made of extruded alluminium with milky white diffuser and inbuilt electronic driver system lumen output should be at least 2000 lumen with a CCT of 6000 K, power factor should be greater than 0.9 with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed. 83 Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete a CCT of 6000 K, power factor should be greater than 0.9 with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed. Make Philips/Bajaj/C&S electric 84 Supply and install split AC indoor/outdoor 1.5 TR with in built Heating and Cooling operation and digital Inverter twin rotary compressor, AC,230V,single phase, with cordless remote control unit with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2.of capacity and complete AC mounting stand along with clamps, nuts, bolts, washers etc. extra cooper tubing with proper insulation, PVC drain pipe of suitable length, Sheet metal enclosure, single pole and neutral with two pin and earth plug and socket with MCB 20A, suitable for protection of appliances like AC/Geyser suitable for flush mounting and surface mounting complete all as specified. 85 Supply and fix LED Bldg security light fitting 35 W housing made out of die cast aluminum alloy with toughed glass, IP 65/66 protection having clamp for mounting on wall working on 240 V AC 50 Hz, 20 watts including fixed on wall with 02 Nos MS clamps and bracket made of 40 mm dia light grade GI pipe bend to shape. complete all as specified and as directed. Make : Crompton/Havells/Philips. 86 Supply, install, testing and commissioning of commercial Air Curtains of size 40 x 90 unit for prevention of dust and conditioned air losses, single phase, 240 V, 50 Htzs made out of MS/CRCA 18 gauge finished with two coat of red oxide primer and final coat of synthetic enamel paint(oven baked) with square perforated suction greels, aluminium alloys fans and single phase electric motor, nozle etc, complete with fittings and accessories so as to produce 1 -1.5 m/sec air velocity at floor level for door openeing specified.all as specified and directed 87 Supply and fix Voltage stabilizer for automatic operation, single phase Each naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V-with accuracy of ± 2.5% and of capacity 4 KVA. 88 S&F of DB epoxy powder coated TP & N 4 ways (VTPN MCCB DB) with metal door (IP 54 IK 09 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts and suitable for one FP MCCB 63 Amps as incomer and 12 SP MCBs or 4 TP MCBs (or any combination of SP/TP MCBS) outgoings complete all as directed. 89 S&F of MCCB, 63 Amp, Four Pole, 415 Volt Make - Legrand/Schneider-Acti 9/Siemens-Betagard 90 S&F of MCB, 6 to 32 to Amp, SP , 230 Volt Make - Legrand/Schneider-Acti 9/Siemens-Betagard 91 Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CMM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and connecting up and including provision of twisted three core PVC insulated flexible cord of 0.75 Sqmm copper conductor of required length from ceiling rose/connector to fan complete all as specified and directed. 92 S&F of stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd 93 Supply, Installation and testing of Desert Cooler electric driven (Single phase) for rooms up to 35 Sqm, large pad area for superior cooling, power ful fan , water tank capacity 51 ltrs including iron stand of suitable size as required to mount desert cooler on wall complete all as specified and directerd with following specifications :-Size of Desert Cooler - L x b x h 660 x 660 x 825 mm (26 x 26 x 32.5) ApproxFan Motor : (i) Fan motor should be copper winding, 500 mm Sweep Cooler fan, three speed (High/Medium/Low) with methalic blade duly painted with Snthetic anti corrosive oven cured paint fitted to body Fan motor Make : Bajaj/Khaitan/Crompton Greaves/GEC (ii) Input Cap 200 watt(approx), Speed 1400 RPM, 230 Volts, 50 Hz, Air Delivery 5000 Cum/HrsSubmersible Pump Motor: Input Cap 40 watt (Approx), Speed 1300 RPM, 230 volts, 50 Hz.Switches/Regulator: One Piano Switch and one Speed Selector Switch (Regulator) 04 Position for controll of Pump Motor and Fan motor respectively will be provided on the body.Pads : Wood wool Pads of proper Thickness will be provided in each panel (Set of three).Drain Plug : Brass drain plug shlall be provided from pump motor to three panel fitted on the cooler body.Cord : Flexible cord PVC Shethed and Insulated size 40/0.25 mm (1.5 Sqmm) 3 core (as per IS 694/1977) length 5 Mtr long with three pin 5 Amp ISI marked Bakelite plug Top shall be provided for power supply to cooler.
