Tender For Proposed Carpentry Works For Residential Quarters For Doctors And Dharamshala At Haffkine
Tender Value
12.80 Lakhs
Estimated cost
Bid Submission
13 Oct 2025
0 days left
EMD
25600
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
parel → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Proposed Carpentry Works For Residential Quarters For Doctors And Dharamshala At Haffkine
BOQ
| Sl. No. | Item Description |
| 1 | A - Carpentry workLabour charge only for removing and re-fixing available door shutter / window frame with necessary modification including cutting the existing shutter providing leeping patti all around the shutter if required including removing and refixingavailbale old hinges, mortice lock, tower bolts ect. fixing aligning the door shutter in proper plumb and level etc. complete all as per specified and directed by Engineer-In-ChargeRemoving andrefixing door shutter |
| 2 | Providing FRB shutter o f30 mm including all fitting of approved make of quality brass/SS such as hinges , tower bolts, locking arrangement with screw etc. Specified & directed by EIC |
| 3 | Providing and fixing C.P.brass hard ware, all fittings and fixture as follows. Complete.AldropsS.S.aldrop 10 inch long |
| 4 | Providing making and fixing in position counter consisting of top (all width 2inch-6 inch) made out of 25mm commercial ply of approved make supported on drawer unit of ht.2 inch -6 inch and vertical supports at regular internals as shown in drawing made out of 15mm thick approved commercial ply and the counter made above the table of required width and size with vertical divider allmade out of 19mm thick approved commercial ply and 12mm thick approved commercial ply for front side of counter with approved laminate or 10mm teak wood lipping on all exposed edges and table top edges should be 1 ½ inch x1 ½ inch finishing with and approved colour and moulding plastic laminate 1.0mm thick for all exposed surface etc. all inside surface shall be 0.8mm thick approved laminate soft boardof 12mm thick pasted with approved adhesive and covered with tepestery felt cloth of required colour including cost of all hardware like hinges, tower bolt, handles, knobs, computer ready-made keyboards, cable manager, CPU stand made by 19mm thick ply with approved laminate finish and locking arrangement with Godrej multipurpose lock etc. complete as specified and directed. |
| 5 | Providing and fixing alumimium partitionto the required height partly glazed and partly panneled or fully glazed or fully panneled using aluminium section ofapproved make heavy quality section 3\" x1½ \" / or of various section lesser than mentioned size as approved by EIC. The Aluminium section shall be of Satin finish anodizing of required size for bottom, top, middle and vertical rails at required intervals panneling with 12mm thick nova pan or ancholam both side pre-laminatd board fixed with sloping aluminium beeding alround with neoprine gasket glazing with 5.5mm forsted/ bajri/ plain glass of approved make like M/s.Triveni, Shri.Vallabh/J/A/G pilkinten fixed with alumimium channel beeding two way PVC lining/ rubber gasket to ensure water tightness and no rattaling including providing necessary cover mould using suitable alumimium section so as to take care of gaps between the walls/ ceiling / flooring and partitions etc. including providing and fixing necessary fittings as specified and directed.Partly glazed partly panneled. |
| 6 | Providing, fabricating and making working / writing table of required size as shown in drawing. Table top 600 mm.width consisting of 19mm thickcommercial ply of approved make resting over vertical supportsof 19mm thick approved commercial plywood required intervals as shown in drawing, including drawer unit all expossed edges should be lipped with 6mmthick lipping patti and all exposed surfaces should be laminated with 1.0mm thick plastic laminate of approved make and shade non-laminated area should be polished with 2 coats of french polish legs if required to be made out of 2 inch x 2 inchT.W. for required height. Including all necessary fittings like C.P.brass/S.S.hinges of approved Archies make, Godrej multi purposes lock, tower bolt, ball catches and C.type powder coated handle etc. complete all as specified and directed by Engineer-In-Charge. Drawer unit specification same as item no. 11 |
| 7 | Providing and fixing cabinet made up of 19 mm. Commercial ply of approved make for top, bottom, sides and shelves and 8 mm thick commercial ply approved make for back side.Door shutter made up of 19mm thick commercial ply and All exposed surfaces including shelves for open type cabine should be laminated with 1.0mm thick approved plastic laminate sheet of required colour including all brass fittings such as hinges, tower bolts, ball catches, stopper, handle, knobs as per shown in drawing or approved by Engineer-In-Charge etc.and all exposed edges shiuld be 6mm thick lipping patti or PVD lipping patti matching with laminate finish, locking arrangement with Godrej multipurpose lock etc. All inside areas shall be .80mm thick approved colour laminate etc.all complete as specified and directed by Engineer-In-Charge.With shutter |
| 8 | KEYS HOLDING CABINET: cabinet providing and fixing Key board made out of 1 ½ inchx2 inchthick teak wood frame with 12mm thick ply of approved make for back fixing ½ inch Dia brass C.P. cup hook at required spacing on back ply.Door shutters single or double leaf consisting of 1 ½ inch x2 inchthick T.W.bedding pattles from both sides and fixing with brass hinges of required size with necessary ball catch, acrylic knons of 1inch dia locking arrangement with godrej multi purpose lock, 2 inch brass tower bolts in case of double shutter including french polish of 2 coats of required shade all over wood surface including providing necessary wall mounting hardware etc. all complete as specified and directed to the satisfaction of Engineer-In-Charge. For double shutters. |
| 9 | Notice Boardproviding and fixing notice board made out of 1inch x 2 inch thick teak wood frame work with 6mm thick commercial plywood of approved make and quality for back above that soft board of .5 inch thick pasted with approved adhesive and covered with tepastry felt cloth (jute fibre) required colour glass door-shutters consisting of 1.5 inchx 1 inch thick teak wood frame with 3mm thick clean glass fixed with T.W. beading patti both side and fixing with brass hinges of required size including acrylic knobs of 1inch dia. Locking arrangement with godrej multi purpose locks 2inch brass tower Bolts, back catch in case of doubleshutters including french polishing 2 coats as specified all over wood surface etc.all complete as specified and directed to the satisfaction of Engineer-In-Charge.Open type notice board. |
| 10 | Providing fixing door frame and shutter side hung to consist of partly glazed partly panneled/ fully panneled/ fully glazed with 5.5mm thick glass sheet of approved make and quality plain or frosted of bajri glass of approved make like M/s. Triveni/Shri Vallabhj/J//A/G pilkinten fixed with two way PVC lining/rubber gasket to ensure notes tightness and no rattaling and panneling with 12mm thick nova pan or Ancholam finished on both side as required using extruded alumimium section forshutter frame jindal 24254545mm satin finish anodized including P/F push-pull plates handles and of approved make and heavy duty fittings like tower bolts of Archies/Everite make Motice lock of Laxmi/Gold locks with keys hinges of 5 inch or 6 inchas per requirement hydraulic door closer/ floor spring of Henco/Hyper/Everite make of suitable capacity etc.complete as specified and directed.With powder coated |
| 11 | Fabricate and install complete ACP panel cladding system of approved shade, but not limited to formed ACP panel. ACP panels shall be 4 mm thick sheet (alloy designation 310 S). The panels shall be finished with PVDF Coating on the top and a service coat on the reverse side. Coating shall conform the specification of ECCA / AAMA and conforming to the mechanical properties of panel as per detail technical specification. The system comprises extruded aluminium sections 40mm X 25mm heavy duty Jindal make section to be fixed using G.I Brackets( duly HDG) and stainless steel bolts, nuts and spring washer along with isolators. The system shall be designed to withstand a wind pressure of 1.5KPa at all levels, elevations and heights. Horizontal joints to be sealed with weather silicon (789 dow) including scaffolding and removing existingdamaged ACP etc complete . All exposed aluminium extrusion (cleats) shall be 6063 T6 alloy.( Basic Price of 4mm ACP cladding sheet - Rs.1100 Per Sqm) (Rate worked out as per CPWD & added aluminum framing.) |
| 12 | B- Civil workInternal plastering with readymix cement mortor using factory manufactured premix / readymix of Roofit Mix of M/S Premiere floor to roof materials PVT Ltd / Easy Plast of M/S Walpast ProductPvt Ltd / Readiplast of M/S Ultratech cement Ltd /Sound Plast PMC -1/ of M/S Sound Buildcare Pvt Ltd / or other approved equivalent make having minimum composition of C : S :: 1 : 4 using fully treated dry well graded natural sand conforming to IS 383 having low rebound properties, low water demand for curing properties,apply over internal masonary applying as per manufacturer\"s specifications including scafolding, cleaning, curing and disposing off debrise out of hospital premises, etc.complete all as per directed by Engineer-in- Charge. (20mm thick) |
| 13 | PLASTER BREAKING :Labour charges only for removing existing damaged / cracked / loosened cement / neeru / rough casts and faced plasteror tile work with back coat at all floors and levels includingcleaning the surfaces clear of all loose concrete/ mortar foreign materials, carting away the debris outof hospital premisesincludingscaffolding raking out joints of brick / stone masonry haking concrete surfaces etc. complete with quantities to be executed as and when required and as directed by the engineer in charge. ( disposing / taking away the debris outside the premises & disposing as per the guidlines of statutory authoritised. ) |
| 14 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m² |
| 15 | GI sheet valley gutters – Providing fabricating, erecting and installing in position valley gutters using 16 guage galvanised iron sheet, in trapezoidal from to required slope, line and level including, fixing to the existing truss members, providing necessary cut outs / funnels for rain water down takes, necessary GI nut bolts, bitumen washers, grouting at the gable and M.S. flats (50mmx5mm) supports at every 1.5m length including all necessary scaffolding etc. complete.Note: Measurement shall be in Sqm(M2) obtainedby multiplying inside perimeter of the gutter (GI sheet only) with length of the gutteras actually fixed in position. Overlaps will not be measured separately. |
| 16 | Providing / fixing / welding / fabrication of \"B\" class G.I. pipe for various structure as per requirement of approved make (Zenith make) including cuttings welding as per requirement at all floors & levels with one coat of metal primer etc. complete.40mm |
| 17 | Providing & fixing bird / pigean net with accessories ( fixing with hooks )Garware make, HDPE Twine 15ply, lab certified ultra voilet stabilized colour, HDPE natural white thickness 0.80. Twine breaking strength - 16.3 kgs. Twine knot breaking strength - 2.6 kgs 35mm x 35mm squre. |
| 18 | Supplying, Installation of 8mm thick green / plain reflective thoughened glass including cradel loading / unloading charges, TP certificate charges, including silicon,, labourcharges,wastage,transportation,hardwarefittings making joint leake proof, debrise/scrap removing, leak test and site clening etc.complete |
AI Tender Summary
Tender Timeline
Sep 30, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedOct 13, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 15, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender