Renovation Work Arrangements At Aringar Anna Maligai In Thallakulam Ward 31; 1.01 Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper wire with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 4 points / Coil) Lower End - SD 273 2.01 Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module Plastic surface mounting switch box on wall with 6A one way module switch with module front plate with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 4 points / Coil) Higher End SD 274 3.01 supply and fixing of 1200mm (48) sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18) 4.01 Supply and Fixing for 450mm Sweep Wall Mounting Fan including labour charges etc complete 5.01 Supply and fixing of single box type 440W fluorescent fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed FRLS copper leads from terminals to the fitting with tube SD 90 6.01 supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. SD 441 7.01 Supply and Fixing for Network Switch, Network Accessories, Cables CAT 6A UTP Armoured Cable inclduing Labour charges etc Complete 8.01 Supplying and Fixing for Vinyl Flooring 2mm thick including labour charges etc Complete 9.01 Supplying and Fixing for Vertical Blinds Premium M-0655 Including labour charges etc Complete 10.01 Fabricating Supplying and fixing in position of Aluminium anodised natural colour mattfinish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 3.50 x 2.88m. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/ m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use. 11.01 Fabricating Supplying and fixing in position of Aluminium anodised Powder Coated ofsingle leaf door with half panelled with 12mm thick both side laminated particle boardat bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shallbe with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter framemade of section Vertical & Top rail: 50x44.45x2.50mm@1.292 kg/m and Bottom rail:100x44.45x2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m,Alu.Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 kg/m andnecessary accessories such as aluminium clips, rubber beading, PVC felt, handle for alength of shutter (both sides), locking arrangements, furniture fittings such as aluminiumtower bolts-250x12mm - Eachs., aluminium tower bolt 200x12mm - 1No., aluminiumHydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush including costof materials labour charges and power consumption charges required for fabricationincluding chipping, dismantling and making hole to the required extent in RCC column,beams, masonry with power drill wherever necessary and redoing the damaged portionto the original condition after fixing etc., complete complying with standard specificationand as directed by the deparmental officers.. All the Alu. Section are to be anodised withmatt finish under electricaly controlled conditions in accordance with IS 1868/1962 foran average anatic film thickness of 15 microns etc., complete. Aluminium sections,andfurniture fittings shall be got approved by the Executive Engineer incharge. 12.01 Removing the Existing Paver block M40grade 80mm thick & 60mm thick in the the rate including Removing and Stock to the Same Site and tranporting loading unloading and Labour Charges and Other tools etc.complete as per standard specification,. 13.01 ReFixing of Existing Removed Paver block M40grade 80mm thick & 60mm thick in uniform shape of approved make to be laid influrring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification,. 14.01 Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification 15.01 Supplying , fixing and roofing with colour galvalume sheet of 0.47mm thick with all necessary accessories such as J/V bolt and nuts of suitable length with suitable bitumen washers complete complying with standard specification and as directed by the departmental officers. 16.01 Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hand broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted, etc., complete complying with standard specfication. 17.01 Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two Crushed Stone Sand and Four aggregate) using 6 to12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trowel, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers) - For 50 mm thick 18.01 Painting Two coats with ready mixed Old Wall Surface Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m 19.01 Supply and Fixing for Stainless Steel Sink Wash Hand Basin of size 600mm x 450mm x 200mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia ‘B’ Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc Colour with Pedastal etc Complete
