Tender For Annual Plan-Kannur Block Panchayath : Project No : 96/2025-26-Renovation Work At Block Industrial Estate-General Civil Work

Sharing tender

Annual Plan-Kannur Block Panchayath : Project no : 96/2025-26-Renovation work at Block Industrial Estate-General Civil Work--- 1 Industrial estate 2 15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar 3 15.28.2:Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :Asbestos cement Sheet 4 OD323549/2025-2026:Removing window shutters as per the direction of Site Engineer-in-charge.(DAR code 50.14.1.2 modified) 5 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil 6 OD323118/2025-2026:Laterate masonry with departmental laterate stones of size 35x20x20cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.(Modified DAR code 50.6.7.1) 7 OD320830/2025-2026:Laterate masonry with neatly dressed laterate stone of size 35x20x20cm or nearest size in cement mortar 1:6 for superstructure above plinth level up to floor two level including all cost of materials, labour charges etc. complete.(Modified DAR code 50.6.7.2) 8 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal sizederived from natural sources) 9 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete 10 OD320875/2025-2026:Providing and fixing Alu Zinc profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.40 mm (+0.05%), thickness . Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (DAR code 12.50 modified) 11 21.1.2.1:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium ( anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15) 12 21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 13 13.1.2:12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand). 14 13.37.1:White washing with lime to give an even shade:New work (three or more coats) 15 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work 16 13.99.1:Painting with synthetic enamel paint of approved brand and manufacture ofrequired colour to give an even shade :One or more coats on old work 17 OD323215/2025-2026:Supplying and fitting name boards of size 75cmX45cm made with GI plain sheets 1.25mm thick(Class III) fitted with 35X35X4mm MS angle 2Nos horizontally and 3Nos vertically to make a frame for strengthening the GI sheet,fitted 2Nos 32mm GI pipe vertically 90cm above from ground level and fixing in cement concrete 1:2:4,30cmX30cmX30cm including cost and conveyance of all materials,all labour charges,fabricating etc. complete. 18 OD323214/2025-2026:Printing New Letters and Figures of any Shade; Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and Technical Specification Clause 1701 Details for 100 letters of 160 mm height, i.e., 1600 cm Unit = per cm height per letter