|
| 1 | Excavating in post holes hard/ dense soil (or similar holes) each n. exc 0.5 cum, getting out, returning, filling in and ramming earh or broken rubble mixed with earth around , in layers not exceeding 25 cm. complete all as specified and directed. |
| 2 | M&L for PCC 1:3:6, type C-2, using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete including sub base of floors and floor finishing complete all as specified and directed. |
| 3 | S&F structural steel work as in roof trusses (framed), trussed, purlins crane gantries, rails & fastenings & heavy brackets framing (beam, tee, angle, gusset plate,channel or flat section including distance pieces, cleats etc, structural steel confirming to Fe-410w, Gde 250, quality - \"A\", complete all as specified and directed. |
| 4 | M&L for steel work in tubular trusses, columns, purlins and rafter including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240, complete all as specified and directed. |
| 5 | S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board, valley gutter etc, fixed all as per manufactures\"s instructions, fixed with self tapping screws and covered with silicone sealant as directed, at site with suitable arangement as required, complete all as specified and directed. |
| 6 | S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board, valley gutter etc, fixed all as per manufactures\"s instructions, fixed with self tapping screws as directed at site with suitable arangement as required, complete all as specified and directed. |
| 7 | M&L for preparing new steel surfaces exc 10cm girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 8 | M&L for 75mm thick plain cement concrete 1:3:6 type C2using 40mm graded stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and smooth without using extra cement, with and incl use and waste of necessary form work complete all as specified and directed. |
| 9 | M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con- forming to Fe.290, Gde-E-165, complete all as specified and directed. |
| 10 | M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in surface channel/ drains incl fair finises &necessary formwork complete all as specified and directed. |
| 11 | S&F decorative type metal sheet eaves boards (Jhallar) 0.50 mm thick of any colour having tensile strength of 550Mpa of 10inch width as complete all as specified and directed. |
| 12 | Demolition of cement concrete of any description and in any position not otherwise specifically provided and comlete removal of demolited for complete all as specified and directed. |
| 13 | Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in hard/ dense soil, complete all as specified and directed. |
| 14 | Excavating over areas, n exc 1.5 m deep and getting out in hard/ dense soil, complete all as specified and directed. |
| 15 | Excavation in trenches ,n.exc 1.5 Mtr wide and n. exc. 1.5 mtr in depth for foundation etc and n. exc 1.5 mtr in depth and getting out in hard and dense soil complete all as specified and directed. |
| 16 | M&L for PCC 1:4:8, type D-2, using 40mm graded crushed stone aggregate as in foundation, filling, mass concrete and sub base for RCC drain, complete all as specified and directed. |
| 17 | M&L for reinforced cement concrete design mix (M-25) as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. |
| 18 | M&L for brickwork with fly ash bricks, straight or curved on plan exc. 6m mean radius, built in CM 1:4, complete all as specified and directed. |
| 19 | Returning & filling including spreading levellingwatering and well ramming in layers n.exc. 25 cm using excavated soil, complete all as specified and directed. |
| 20 | Filling under floor using excavated soil, Spreading and levelling in layers n exc. 25 cm thick well ramming in layers and watering etc., complete all as specified and directed. |
| 21 | Removing excavated soil not exceeding 250 m and depositing where directed at a level not exceeding 500m above the starting point complete all as specified and directed. |
| 22 | S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking bending spirally for hooping for column,roof, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. |
| 23 | All as per Srl item No 22.00 above but for 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, complete all as specified and directed. |
| 24 | M&L for use & waste of form work to sides of concrete foundations, footings, bases of columns, sides & soffits of plinth beams and similar work for rough finished flat surfaces of concrete etc complete all as specified and directed. |
| 25 | M&L for reinforced cement concrete design mix M-25, using 20 mm graded crushed stone aggregates as in columns, pillars, piers, posts and struts etc., complete all as specified and as directed |
| 26 | M&L for reinforced cement concrete design mix M-25 using 20 mm graded stone aggregates as in beam(LB/ RB) etc complete all as specified and directed. |
| 27 | M&L for reinforced cement concrete design mix M-25 using 20mm graded stone aggregates as in roof slab etc complete all as specified and directed. |
| 28 | M&L for use & waste of form work to sides ofcolumns, pillars and similar work sqrare or rectangular in shape for rough finished flat surfaces of concrete etc complete all as specified and directed. |
| 29 | M&L for use & waste of form work tosides & soffits of beams etc such as lintel beam, roof beams and similar work for rough finished flat surfaces of concrete etc complete all as specified and directed. |
| 30 | M&L for use & waste of form work to roof slab and similar work for rough finished flat surfaces of concrete etc complete all as specified and directed |
| 31 | M&L for brickwork with fly ash bricks (old size), straight or curved on plan to any radius in half brick thick walls built in CM 1:4, complete all as specified and directed. |
| 32 | M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of external wall, complete all as specified and directed. |
| 33 | M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces or internal wall, complete all as specified and directed. |
| 34 | M&L for providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth, complete all as specified and directed. |
| 35 | M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed. |
| 36 | M&L for preparation of newly plastered wall surfaces and applyingtwo coats of oil bound distemper over2 mm thick wall care putty over one coat clearcolleprimer including complete all as specified and directed. |
| 37 | M&L for two coats of white wash on newly plastered surfaces of ceiling complete all as specified and as directed |
| 38 | M&L for hardcore broken stone boulders) of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed. |
| 39 | M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate, 75mm thick as in plinth protection finished even and smooth without using extra cement, complete all as specified and directed. |
| 40 | S&F 100mm long butt hings medium weightcold rolled mild steel and fixed, complete all as specified and directed. |
| 41 | S&F 200 mm long aluminum anodized barrel tower bolt of exturded section, complete all as specified and directed. |
| 42 | S&F 125mm long aluminum handles cast type anodized fixed, complete all as specified and directed. |
| 43 | S&F 250 mm long aluminiunm sliding door bolt with hasp and staplebolttype anf fixing clips of sheet cast or extruded section fixing bolts and sliding bolts of extruded section, complete all as specified and directed. |
| 44 | M&L for dry sand filling under floors, foundation or in cable coushioning for cable protection, including watering and consolidation, complete all as specified and directed. |
| 45 | S&F machine pressed precst concrete interlocking paver block of any shape and size and colour confirming to IS 15658-2006 of 60mm thickness M-35 grade laid using grey cement and pigment, complete all as specified and directed. |
| 46 | M&L for 20mm thick screed bed in CM (1:6)as in sub base of floor complete all as specified and directed. |
| 47 | M&L for chequered cement concrete tiles pre polished lacuqer and glossy finish 30cmx 30cm x 20-22mm thick, set, jointedand pointed in neat cement slurry with grey cement and pigment in floors, steps complete all as specifiedand directed. |
| 48 | M&L for PCC 1:2:4, type B-1, using 20 mm graded crushed stone aggregate as in bed blocks, coping, hold fast blocks etc., complete all as specified and directed. |
| 49 | M&L for joint free Non skid ceramic coloured tile 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floorsetc.over and including 15mm thick screed and bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or colour cement to match with the existing surfaceetc., complete all as specified and directed. |
| 50 | M&L for glazed ceramic tiles in vertical surface 350x250mmx7mm/ 450x350x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match, over 15 mm thick cement sand screed 1:4, complete all as specified and directed. |
| 51 | Supply only Integral water proofing compound, complete all as specified and directed. |
| 52 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 90 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction and making it good to match with existing surface, complete all as specified and directed.Note: For WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 53 | S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction, complete all as specified and directed.Note: stainless steel butt hinges shall be paid separately however SS screws rates are deemed to be included in quoted rates. |
| 54 | S&Fvitreous china wash down water closet pan (EWC) includinglow level flushing cistern 10 Ltrs capacity, trap, seat & cover incl flush pipe etc., complete all as specified and directed. |
| 55 | S&F Vitreous China wash basin, white, flat back, size 550x400mm including pedestal stand complete all as specified and directed. |
| 56 | S&F vitreous china half stall urinals flat back white minimum with grating and union for discharge pipe, providing & fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with & incl 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with nbrackets, flush pipe, grating and union for discharge pipe complete all as specified and directed. |
| 57 | S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. |
| 58 | M&L for 15mm bore `medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 59 | M&L for20mm bore medium grade tube galvanised with all fittings and fixed complete to walls & ceiling or laid in floor complete all as specified and directed. |
| 60 | M&L for 500 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed. |
| 61 | S&F of ISI Marked 15mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed. |
| 62 | M&L for ISI marked 15mm bore bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 63 | S&F of ISI marked 15mm bore stop valve/ angle valve, fancy type, CP, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed. |
| 64 | S&F of 15mm size PVC connection with PTMP nuts of length 450mm complete all as specified and directed. |
| 65 | PVC (SWR) pipes110 mm bore dia single socketed in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed. |
| 66 | PVC (SWR) pipes 75 mm bore dia single socketed in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed. |
| 67 | S&F PVC (SWR) bends 75 mm bore of any radius complete all as specified and directed. |
| 68 | S&F PVC (SWR) bends 110 mm bore of any radius complete all as specified and directed. |
| 69 | M&L for 75mm bore dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1, complete all as specified and directed. |
| 70 | S&F steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed. |
| 71 | S&Fgalvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.40mm, complete all as specified and directed. |
| 72 | S&F figured glass 4mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pan complete all as specified and directed. |
| 73 | S&Fbrass chromium plated central hole basin mixer with regular spout, popup waste system and 450mm long braided hoses with connection and nuts complete all as specified and directed. |
| 74 | S&F15mm bore stop valve, cast copper alloy fancy type chromium plated with long shank and cup (concealed type ) screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed, complete all as specified and directed. |
| 75 | S&F 15mm bore stainless steel chrome finish angle/urinal valve with flange screwed one end of iron pipe or for union and fixed, complete all as specified and directed. |
| 76 | S&F brass chromium plated wall mixer for mixing hot & cold water including Hand Shower screwed down for iron pipe and fixed, complete all as specified and directed. |
| 77 | S&FPVCbathroom cabinet mirror 450 x 350 mm complete all as specified and directed. |
| 78 | S&Fswivel shower of chromium plated any colour with shower arm 15 mm size 195 mm long with bend of 45 degreewithflange of any colour for fixing with 15mm pipe, (minimum weight 40gms), complete all as specified and directed. |
| 79 | S&Fsoap dish approximately size 160 x160x 90mm and fixed withas chromium plated brass screws complete all as specified and directed. |
| 80 | S&FPVC corner shelf with bracket complete all as specified and directed. |
| 81 | S&F CP brass teliphonic spray(ABS Body) (health faucet) mild steel chromium plated with flexible pipe 1.25m long and ABS hookfixed to EWC suitable for 15mm bore of pipe fixed, complete all as specified and directed. |
| 82 | S&FCP grating doom 100mm dia complete all as specified and directed. |
| 83 | S&F32mm dia PVC waste pipe for wash hand basin and kitchen sink of length 900mm long with PTMT nuts complete all as specified and directed. |
| 84 | S&Ffor brass CP fancy type 15mm bore pillar tap for WHB, complete all as specified and directed. |
| 85 | S&F 60 cm long sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 120 mm wide with chromium plated bracket guard and railing complete all as specified and directed. |
| 86 | S&F CP Toilet paper holder with flap coverfixing with all necessary arrangementsscres etc., complete all as specified and directed. |
| 87 | S&F 900mm x 600mmmirror of selected quality glass 5.5mm thick, mounded on 6mm thick building AC board or commercial plywood secured with hardwood beading, melamine polish all round andfixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 88 | S&F sheet glass ordinary quality 4 mm thick glazing in square/ rectangle n.exc 0.50 sqm each pan with oil putty or aluminium beads fixed to steel and wooden of any height including necessary scaffolding and T&P required to complete the work complete all as specified and directed. |
| 89 | S&F150mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps, bend, socket & collar as required complete all as specified and directed. |
| 90 | S&F on site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, incl PCC 1:4:8, 100mm thick, below foundation, vent shaft, connection etc., complete for05 user (2500 Ltrs) with upflow filter including media, complete all as specified and directed.Note: Excavation shall be measured and paid separately. |
| 91 | Excavation for the soakage pit shall be conducted in any type of soil to achieve the specified dimensions. The pit walls shall be constructed using 230 mm thick honeycomb brick masonry to allow for effective water percolation. A PCC of 100 mm thick of 1:4:8, mix ratio shall be laid specifically beneath the brick masonry wall to provide a stable foundation. The top ring shall be made of M-25 grade concrete for reinforcement, and a cover slab of either M-25 grade Reinforced Cement Concrete (RCC) or Steel Fibre Reinforced Concrete (SFRC) shall be provided for secure closure. The pit shall be filled with graded brickbats to aid water dispersion and will have an internal diameter of 1.2 meters with an effective depth of 1.5 meters. An inlet pipe shall be installed to direct water into the pit. All constructions shall be carried out in accordance with specified guidelines and directions, complete all as specified and directed.Note: Rate include all items including excavation, PCC, SFRC, RCC etc. |
| 92 | Concrete bed to 150 mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, in PCC 1:4:8, type D-2, using 40 mm graded crushed stone aggregates, complete all as specified and directed. |
| 93 | M&L for 150 mm bore salt-glazed stoneware drain pipes, grade \"A\" laid in trenches and jointed, complete all as specified and directed. |
| 94 | M&L for brick work with sub-class \"B\" bricks, straight or curved on plan exc 6 m mean radius and built in CM 1:4, complete all as specified and directed. |
| 95 | M&L for providing PCC 1:2:4, type B-1, using 20 mm graded crushed stone aggregates as in cover slabs for manholes etc, set in cements mortar 1:6, complete all as specified and directed. |
| 96 | M&L for TMT bar 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and directed. |
| 97 | S&F600mmx450mm mirror of selected quality glass 5.5mm thick, mounted on 6mm thick building AC board or commercial plywood secured with hardwood beading, melamine polish all round andfixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 98 | M&L for rendering 5mm thick in CM 1:4, on concrete surfaces of ceiling, complete all as specified and directed. |
| 99 | M&L for vitrified ceramic dark shade tiles 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm, in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match, over 15 mm thick cement sand screed 1:4, complete all as specified and directed. |
| 100 | M&L for vitrified ceramic light shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over 15 mm thick cement sand screed 1:4, complete all as specified and directed. |
| 101 | S&F for 1st class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. |
| 102 | M&L for plain, framed, panelled shutters (any number ofpanels) in 1st class hardwood 40mm thick, with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats and framing moulded in solid (On each side), complete all as specified and directed. |
| 103 | M&L for prepareing new wood surface of any description not otherwise descri-bed, over 10cm width or girthand applying two coats of synthetic enamel (ordinary tint) over pink primer, complete all as specified and directed. |
| 104 | S&F powder coated aluminium sliding window three track with frame & two glass shutters using 4 mm thick glass tinted modi guard and shutter with stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm using aluminium powder coated section aluminium cleat, PVC track, bearing handle lock rubber beading etc complete fittings as approved, complete all as specified and directed.Note :- Size of aluminium section shall be under :-(i) Three track top and vertical - jindal main-2010 section No 20621 or equivalent as approved by GE.(ii) Three track bottom-Jindal main-2010 section No 20620 or equivalent as approved by GE. (iii) Shutter vertical section-Jindal main-2010 section 20604 or equivalent as approved by GE.(iv) Shutter top and bottom-Jindal main-2010 section 20604 or equivalent as approved by GE.(v) Shutter vertical middle (interlock) - Jindal main-2010 section 20605 20604 or equivalent as approved by GE. |
| 105 | M&L for powder coated anodised aluminium grill wt n exc 5.60 Kg per sqm with all fittings & fixture complete all as specified and directed. |
| 106 | S&F mild steel screw bolts 16mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 15 cm but n exc 22.5cm long complete all as specified and directed. |
| 107 | S&F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming toFe.290.Gde-E-165(Brackets over 10 kg each to be measured under \"Structural Steel\")all as specified and directed. |
| 108 | M&L for machine cut Kota stone slab flooring 20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing including 20mmthick screed bed with cement mortar 1:6 complete all as specified and directed. |
| 109 | M&L for Machine cut Kota stone slab flooring 20mm thick in skirting/dados and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishingincluding 10mmthick backing coat incement mortar 1:4 all as specified.complete. |
| 110 | M&L for aluminium sliding door/ partition with necessary sliding tracks/ G channel, locking arrangement/ mortice lock, handle, tower bolt fixing the frames to wall/ floor/ ceiling as required with dash through fasterners, complete all as specified and directed. |
| 111 | M&L for 12mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations one, fixed with screws to timber or aluminium frame work complete all as specified and directed. |
| 112 | S&F 5.5mm thick sheet glass fixed to aluminium frame work using anodized aluminium bead, rubber beading and packing in panels exc 0.5sqm in each pane complete all as specified and directed. |
| 113 | M&L for concealedpoint wiring 1.5 Sqmm (nominal cross sectional area) with colour coding multistranded copper conductor cable, PVC insulated (FRLS-H) and unsheathed cable and including drawn through in concealed with PVC Conduitwiring with all fittings and accessories, terminated to sunken box and laminated sheet of suitable size for housing/mounting the switches/sockets including 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable earth wire connected to common earth dolly for one light/fanpoint control by one, one way switch complete all as specified and as directed. |
| 114 | All as per Srl item No 113.00 above but for one 3 pin socket oulet 5 amps, onsame board with other switches, complete all as specified and as directed. |
| 115 | All as per Srl item No 113.00 above but for one 3 pin socket oulet 5 amps, onindependent board, complete all as specified and as directed. |
| 116 | All as per Srl item No 113.00 above but for one 3 pin 15 Amps power point on independent board with 2.5 Sqmm complete all as specified and directed |
| 117 | S&F switch piano flush type single pole, one way 5 Amp ( ISI marked)complete all as specified and directed. |
| 118 | S&FMCB protected socket 15/20 Amp including 25 Amp MCB suitable for domestic and commercial uuse gyeserwith PVC box, sheet steel enclosure (ISI marked) flush type complete all as specified and directed. |
| 119 | S&F socket (ISI Marked) 2 in 1, 3 pin 5/6 amps flush type complete all as specified and directed. |
| 120 | S&F ceiling rose ,3 phase ,PVC polycarbonate ,insulated body (ISI Marked) complete all as specified and directed. |
| 121 | M&L for lamp holder (Angle) PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. |
| 122 | S&F LED 12/14 watt complete all as specified and directed. |
| 123 | S&F LED INVERTER tube light along with fixture, 1x 20 watt, (4 Feet) wall mounted LED battern, integrated electronic driver with heat sink provided for efficient heat dissipation, optics diffussed, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed. |
| 124 | S&F LEDINVERTER tube light along with fixture, 1x 10 watt, (2 Feet) wall mounted LED battern, extrudedd PVC, heat sink provided for efficient heat dissipation & integrated electronic driver, optics diffussed, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed. |
| 125 | S&F LED Bulkhead luminaire 20WDecorative type as per sample complete including electrical connection with copper cable from ceiling rose to fittingsand including taking down existing fittings, complete all as specified and directed. |
| 126 | S&F LED building securtiy light 35/40 watt fixed on wall suitable bracket with all connected accessories complete including electrical connection with copper cable from ceiling rose to fittings and all fixing arrangements complete all as specified and directed. |
| 127 | M&L for submain wiring with 2X6.0Sqmm+1X6.0Sqmm Earth Wire single core PVC insulated FRLS-H PVC sheathed cooper cableconnecting to common earth dolly in and including heavy duty PVC Concealed Conduit as per site requirement and direction by EIC, with all accessories complete all as specified and directed. Note: Three runs of copper wire for phase , neutral, earth & one run PVC conduit/ casing shall be measured one unit length, complete all as specified and as directed. |
| 128 | S&F sheet metal enclosure MCB DB 8 waySPN double door suitable for 240 V fixed flused on walls including cutting Knitch and making good disturbed surfaces complete all as specified and directed. |
| 129 | S&F sheet metal enclosuresDB\"s 4 waySPNdoubledoor suitable for 240 Vcomplete all as specified and directed. |
| 130 | S&F MCB SP (single pole ) 06 to 32 Amps \"B\" Curve with 10 kA for inductive load connected through cable lugs of suitable size complete all as specified and directed. |
| 131 | S&F MCB SPN/ DP (single pole and neutral )32/40 Amps \"B\" Curve with 10 kA for inductive load connected through cable lugs of suitable size complete all as specified and directed. |
| 132 | S&F MCB SPN/ DP (single pole & neutral) 240 volt 40 to 63 amp \"B\" Curve with 10 kA for inductive loadconnected through cable lugs of suitable size complete all as specified and directed. |
| 133 | S&F MCB protected socket 15/20 Amp including 25 Amp MCB suitable for domestic and commercial uuse gyeserwith PVC box, sheet steel enclosure (ISI marked) flush type complete all as specified and directed. |
| 134 | S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc and fixing arrangements, complete all as specified and directed. |
| 135 | S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm including fixing all arangements complete all as specified and directed. |
| 136 | S&Fservice cable 10 sqmm x 2 core PVC Insulator with Aluminium Conductor Cable 230V grade ISI complete all as specified & directed. |
| 137 | M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less\"than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion including galvanised strip protected by 32 mm bore light grade galvanised iron pipe and earth and connected to test point as directed including funnel, watering pipe 20 mm bore light grade galvanised iron wire mesh charcoal and common salt in alternate layers of 15 cm compacted thickness all arround the GIelectrode with concrete pit in PCC 1:3:6 type C1includingnecessary excavation in soft/loose soil and disposal of soil to a distance not exc 50 m and necessary testing completeconnected to earthing test point complete all as specified and directed. |
| 138 | S&F LED building securtiy light 36 watt 230V, AC outer type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple oprics complete with IP 65/ 66 protection complete including electrical connection with copper cable from ceiling rose to fittings, complete all as specified and directed. |
| 139 | Excavation in trenches ,n.exc 1.5 Mtr wide and n. exc. 1.5 mtr in depth for foundation etc and n. exc 1.5 mtr in depth and getting out in Soft/ loose soil complete all as specified and as directed by Engr-in-charge |
| 140 | Supply and laying well burnt old size sub class \"B\" bricks laid in tranches for cable protection, complete all as specified and directed. |
| 141 | M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100Volts grade, cross-sectional area 6 sqmm, 2 core, complete all as specified and directed. |
| 142 | Supply and laying PVC corrugated heavy duty suitable for under ground cable including with all fittings 40mm dia, complete all as specified and directed. |
| 143 | M&L for cutting of existing GI tubing 40/50mm dia for making new connection in position for insertion of new tees, branches, T and size Nipple suitable for 25mm dia GI pipe including excavation, returning filling, complete all as specified and directed. |
| 144 | S&F medium grade galvanized pipe 25mm dia with all fitting laid in trenches, complete all as specified and directed. |
| 145 | S&F medium grade galvanized pipe 20mm dia with all fitting laid in trenches, complete all as specified and directed. |
| 146 | M&L for Gun metal, globe or gate valves 25mm with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 147 | M&L for Gun metal, globe or gate valves 20mm with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 148 | M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate, slab flooring, bedded and jointed in CM 1:6 and pointed in CM 1:3 will be used for road cutting, etc., complete all as specified and directed. |
| 149 | S&F switch piano flush type, single pole, one way 15 Amp ( ISI marked)complete all as specified and directed. |
| 150 | S&F socket (ISI Marked) 2 in 1, 3 pin 15/ 16 amps flush type complete all as specified and directed. |
| 151 | M&L for point wiring 1.5 Sqmm (nominal cross sectional area) with colour coding multistranded copper conductor cable, PVC insulated (FRLS-H) and unsheathed cable and including drawn through in concealed with PVC Casing-n-Caping wiring with all fittings and accessories, terminated to sunken box and laminated sheet of suitable size for housing/mounting the switches/sockets including 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable earth wire connected to common earth dolly for one light/fanpoint control by one, one way switch complete all as specified and as directed. |
| 152 | All as per Srl item No 151.00 above but for one 3 pin 15 Amps power point on independent board with 2.5 Sqmm size FRLS-H, PVC insulated unsheathed multistranded copper conductor as earth wire, complete all as specified and directed |
