Tender For Special Repairs To Atithi Block (Block No P-339) At Snc (O) Mess, Naval Base Kochi.; 1 SPECIAL REPAIRS (B/R ITEMS) 2 Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.5 sqm but not exc 4 sqm eachof size complete all as specified and directed. 3 Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) area not exc 1.5 sqm eachof size complete all as specified and directed. 4 Taking downshutters of any description exc 1 sqm and n exc 2 sqm eachof size complete all as specified and directed. 5 Second class hard wood (sal) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. 6 Second class hard wood, 35mm thick factory made door shutters plain framed, panelled shutter with lock rail and panel of 12mm thick veneered water proof particle board the size of rails and stile as per IS -1003 klin seasoned and chemically pressure traeted complete all as specified and as directed. 7 Second class hard wood, 35 thick Glazed skelton shutters open rebated and prepared to recive gauze etc (withoutsash bars) edges of framing , plain chamfered or rounded fitted with cut and mitread beads for securing glass etc size of members of shutters as specified in SSR Pt-I section 8 cl 24 (a). 8 Preparation of new wooden surface of any description over 10cm in girth/width and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. 9 Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 10 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter andnecessary full body threaded star headed counter sunk S.S screws,complete all as specified and as directed. 11 18-19 mm thick Marine plywood (710 grade) with both side laminated mica sheet glossy finished (not less than1mm) water proof, termite & borer proof, corrosion free with melamine polished shutter for C.B complete all as specified and as directed. 12 Second class HW plain fillets square or rectangular in section areaexeeding 13 sqcm but not exeeding 25 square cm fixed with screws fixed with screwscomplete all as specified and as directed. 13 Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples, chains hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165complete all as specified and as directed. 14 Cutting holes in brick walls (not exc half brick) built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed. 15 Preparing surfaces of steel and iron work, new or old, small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sq. m each, and treated with tar or coal tar black paint treating complete all as specified. 16 Butt hinges 100mm , heavy weight, cold rolled mild steel, and fixed complete all as specified and as directed. 17 Butt hinges 100mm , heavy weight, stainless steel, and fixed complete all as specified and as directed. 18 S/S 15-24mm Sensys Soft Close Crank Hinges (Hettich)complete all as specified. 19 150mm size aluminium handle (ISI Marked) cast type anodized, fixed complete all as specified and directed. 20 150mm size aluminium handle (ISI Marked) cast type anodized, fixed in repairs complete all as specified and directed. 21 150mm size aluminium tower bolt (ISI Marked)anodized, fixed complete all as specified and as directed. 22 150mm size aluminium tower bolt (ISI Marked)anodized, fixed in repair complete all as specified and as directed. 23 Floor door stopper of Aluminiumalloy body and tongue , anodised with hard drawn steel spring, fixed in steel (overall length of cover plate 140mm) complete all as specified and as directed. 24 Floor door stopper of Aluminiumalloy body and tongue , anodised with hard drawn steel spring, fixed in repairs (overall length of cover plate 140mm) complete all as specified and as directed. 25 250mm long Aluminium alloy, anodised, sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixing bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. 26 250mm long Aluminium alloy, anodised, sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloyfixed in repairs complete all as specified and as directed. 27 Mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. 28 75mm hasp and staple Aluminium anodised (ISI Marked) fixed in repair with screws complete all as specified and as directed. 29 Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanized wire staplescomplete all as specified and as directed. 30 Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mmfixed in repairs with tinned tacks, or galvanized wire staples complete all as specified and as directed. 31 Demolition of cement concrete unreinforced in anyPosition not otherwise specifically provided for. 32 Demolition of cement concrete (reinforced) in ground floor and paving not exceeding 15 cm thick (below or above G.L) all as specified and directed. 33 RCC 1:2:4 (Nominal Mix) (type-B1)using 20mm graded stone aggregate pre cast slabs supported on walls for cup board and Kitchen slabs,manhole covers,drains complete all as specified and as directed. 34 Formwork to rough finished surface of concrete to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed. 35 Mild steel CRS TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete all as specified and as directed. 36 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing servicable tiles to store and rubbish off the permises complete all as specified and as directed. 37 25mm thick PCC 1:2:4 ( type B-1)using 20mm graded stone aggregateas in sub-base, floors etc. complete all as specified and as directed. 38 Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.38 sqm, in floors over cement screed 15 mm thick in CM 1:4set andjointed in neat cement slurry and pointed in Epoxy joint filling minimumum 5mm depth and 3mm thick spacer width complete all as specified and as directed . (Cost of Epoxy is inclusive of quoted rate) 39 Vitrified tiles in vertical surface each tiles exceeding 0.18 sqm but not exceeding 1.00 sqm set and jointed in neat cement slurry and pointed in white or coloured cement to matchincludingrendering 10 mm thick in CM 1:4 on fair face of brick work or concrte surface set and jointed in neat cement slurry and pointed in appoxy joint filling minimumum 5mm depth and 3mm thick spacer width complete all as specified and as directed(Cost of Epoxy is inclusive of quoted rate) 40 Light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tile not ecceeding 0.36 Sqm laid onfloor over cement screed 15 mm thick in CM 1:4set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 41 75mm thick PCC1:3:6(Type C1)using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed. 42 Demolition of stone slabs of any description or thickness laid bedded in any motar complete all as specified and directed. 43 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like 20mm thk in cement mortar 1:4 including pointing in white cement1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 44 Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations 45 Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. 46 Demolition of brick/PCC Block masonary work built in cement mortar all as specified and as directed. 47 Precast cement cocrete block masonary 1:3:6 (Type C1) with solid blocks exce 10 cm width and setting in cement motar 1 :6 complete all as specified and as directed. 48 Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in cement mortar 1:4 complete, in walls complete all as specified and as directed. 49 Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed. 50 Cement Plaser in two coats 8mm thick in CM 1:4 mixed with WPC over 12mm thick in CM (1:6) on external surfaces, finished even smooth with out using extra cement with using approved WPC complete all as specified and as directed.Note:-WPC shall be meassured and paid through seperate item. 51 Rendering 10 mm thick plaster in cement CM 1:6 on fair faces of brickwork or concrete surfaces, finished even smooth with out using extra cement complete all as specified and as directed. 52 Rendering 5mm thick cement plaster in CM 1:3 on fair faces of brickwork or concrete ceiling surfaces on ceiling, finished even smooth with out using extra cement complete all as specified and as directed. 53 Supply only Liquid water proofing compound complete all as specified. 54 Preparation of new plastered external wall surface and applying two coats of weather proof (Apex Ultima protek) paint over a base coat of Apex ultima primer complete all as specified and as directed. 55 Preparation new plaster on internal surface of walland applying one coat of wall care putty 1mm thick& Distempering with 1st quality acrylic emulsion (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification two coats on new work over a coat of alkali resistant primer all as specified and as directed. 56 Preparation of new ceiling surface and applying two coat of distemper oil emulsion overa coat of primer over a coat of 1.5mm thick wall care putty including filling of nail holes/disturbed surface by cementious wall care puttyall as specified and as directed. 57 Complete removal of existing treatment on internal surfaces of walls,applying one coat of wall care putty 1mm thick on old surfaces & Distempering with 1st quality acrylic emulsion (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification two coats on new work over a coat of alkali resistant primer all as specified and as directed. 58 Complete removal of existing surface finishes of external wall, preparation of surface and applying two coats of weather proof (antifungal, Asian Ultima Protek) paint over a base coat of suitable primercomplete all as specified and as directed by the Engineer-In-Charge.Note:- Application of paint, primer shall be as per manufacturers instruction. 59 Complete removal of existing treatmenton old ceiling surface & preparation ofsurfaces and applying two coat of distemper oil emulsion overa coat of primer over a coat of 1.5mm thick wall care putty including filling of nail holes/disturbed surface by cementious wall care puttyall as specified and as directed. 60 Antitermite post costruction treatment along the external wall belowconcrete or masonry using chemical emulsion @ 2.25/linear meter including pluging holes etc all as specified and as directed. 61 Antitermite post costruction treatment under existing floors using emulsion one litre /hole 300mm apart including drilling along external wall below including pluging holes 12 mm dia holes with CM1:2 to match the existing floors etc all as specified and as directed. 62 Antitermite post costruction treatment at all points of contact of wood work by chemical emulsion @0.5litre/ hole by drilling 6mm dia holes at a down ward angle of 45 degree at 150mm centre to centre and sealing the same all as specified and as directed. 63 Counter Top wash Basin for hand wash white flat back of size 550x445mm fixed or laid on granite platform includingbrackets, waste pipe & CP brass waste coupling of 32mm dia including pillar tap, fixedin repaircomplete all as specified and directed. 64 Vitreous china wash hand basin, white, flat back, size 450mm x 300mm, exc chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia and CP fancy type pillar tap, fixed in repairs complete all as specified and directed. 65 450 mm long PVC connection 15 mm size with PTMT nut fixed in repairs complete all as specified and directed . 66 Vitreous China coloured wall mounted Stainzfree wash down water closet including flushing cistern fitting fixed in repairs complete all as directed. 67 Viterous China wash down water closet pan (pedestal pattern), white incl plastic water closet seat, black, closed pattern with flat bottom, cover and mild steel chromium plated or aluminised hinging device, fixing bolts, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float & handle incl brackets, PVC connections 15mm size with PTMT nuts of length 600 mm and Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern fixed in repair complete all as specified and directed. 68 Soap dish Stainless steel with chromium plated fixedin repair complete all as specified. Make-Parry ware (Cat No - T6003A1) or equivalentmake in approved list of make. 69 Tubular towel rail, brass chromium plated 20mm dia, D type, 60cm long between flanges fixed in repairs complete all as specified and as directed. 70 Towel Ring brass chromium plated 20mm dia and including Chromium plated brass screws fix in repaircomplete all as specified. 71 Bathroom cabinet mirror304 stainless steel bathroom cabinet (24x16x4 inch ) fixed in repairs complete all as specified and as directed. Make-Kohler (Cat No -K-81144IN-DA1) or equivalent make in approved list of Make. 72 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers fixed in repairs. 73 Demolition ofAC or reinforeced concrete drain pipes 100mm dia jointed in cement mortar and taking out of wall complete all as specified and as directed. 74 PVC (SWR) pipestype B 110 mm dia single socketed in any length with fixing accessories on walls, floors etc complete all as specified and as directed. 75 PVC (SWR) pipestype B 75 mm dia single socketed in any length with fixing accesseries on walls, floors etccomplete all as specified and as directed. 76 PVC (SWR) 110 mm dia vent cowl, complete all as specified and as directed. 77 PVC (SWR) 75mm dia vent cowl, complete all as specified and as directed. 78 PVC Nahani Trap 75mm (SWR) floor trap, plain with grating including jointing with solvent or cement, complete all as specified and as directed. 79 110mm dia PVC (SWR) T single junction with access door, complete all as specified and as directed. 80 75 mm dia PVC (SWR) T single junction with access door, complete all as specified and as directed. 81 Grating doom 125 mm dia with waste hole of SS complete all as specified and as directed. 82 Grating doom 100mm dia of SS complete all as specified and as directed. 83 Stainless steel chromium plated bottle traps 32mm dia for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed in repairs complete all as specified. 84 Stainless steel chromium plated bottle traps 40mm dia for sink with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed in repairs complete all as specified. 85 Water proofing for sunken slabsincluding all materialsas per the stages described below, complete all as specified and as directed. (a) Remove all dust, oil, dirt, laitance and other containments, loose particlesfrom concrete surface . (b) Chamfering the floor wall junctions with cement mortar 1:4 admixed with NitoBond SBr or equivalnt @ 1 litre per 50 Kg bag of cement.(c) Annular space of out let/spoutpipesshall be packed and sealed using Conbextra GP2 or equivalent mixed water and filling as per manufacturers specifications.(d) Carrying outponding for minimum of 48 hours (e)Injection grouting of all leaking spot and honey combs with cementious pressure grouting with 40psi pump using Cebex 100 or equivalent @225 gms mixed to 50 Kg bag of cement incl joints packing using polymer modified mortar. (f) Providing and applying water proof coating using fosroc Nitoproof 600 or equivalent, over dry surfaces to achieve 1.5mm thick with 02 coats with interval period of 6 hours over the surface using spray/ squngee/ roller/ brush. Water proofing coating shall have the elongation of 500-700% (ASTM D412-90), tear resistance of 21Kn/m (ASTMD624-00) and tensile strength of >1.9 N/mm2. Termination to be done on wall extending the coating to min 300mm height above the finished floor level as per vendor recommendation. Laying 200gsm non-woven geo textile membrane over Nitoproof 600 coating with overlap sealed.Make:- FOSROC or equivalent as approved. 86 50mm thick PCC 1:2:4 (type B1) using 20mm graded stone aggregate for sub base of sunken portion complete all as specified and as directed. 87 Glass Corner Shelf 6mm thick including CP railing radius 250mm fixed in repairs complete all as specified and as directed. Make-Parryware (Cat No - T6010A1) or equivalent make in approved list of make. 88 Glass shelf assembly 5.5mm thick, 600mm long 120mm wide with cp railing fixed in repairs complete all as specified and as directed.Make-Parryware (Cat No - T6009A1) or equivalent make in approved list of make. 89 Writing letters or figures (Block. Roman, Italic or Indian) n exc. 15 cm high, complete all as specified and as directed. 90 Writing letters or figures (Block. Roman, Italic or Indian) exc. 15 cm but n.exc 30 cm high, complete all as specified and as directed. 91 Treating crumple joints with necessary treatment etc complete by racking out joints, clearing of loose particles, providing polysterene film / filling to achieve a uniform depth of 15 mm and filling up the joints with polysulphyde sealant throughout the width of joints incl fixingaluminium sheets of 1mm thickness and 150mm widthwith brass screws / washers all as speicified. 92 Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified 93 Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and as directed. 94 Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. 95 Powder coated anodised aluminium frame windows, door with one or more rebates including joining cleat for fixing etc. complete (Sliding type/Side hung type) all as psecified and as directed. 96 Powder coated aluminium door shutters, with 4mm thk coloured/wooden grain aluminium composite panel (approved by Engr-in-Charge) including necessary joining cleats, glazing clips, rubber neoprene packing, suitable handle, tower bolt, SS butt hinges,mortice lock 4 lever with 65 mm latch anodised aluminum snap beading screws etc. complete all as specified and as directed. 97 Sheet glasses, plain4.00mm thickglazingall withaluminum beading& rubber gaskets etcexc 0.5 sqm in each pane fixed in alumuninum window, ventilator complete all as specified and as directed. 98 Sheet glasses, plain4.00mm thickglazingall withaluminum beading& rubber gaskets etc not exc 0.5 sqm in each pane fixed in alumininum window, ventilator complete all as specified and as directed. 99 Structural glass matching with existing glass specification, dimension and frame arrangements including all necessary fittings all as specified and as directed. 100 Figured glass, pin head type plain4.00mm thickglazingall withaluminum beading& rubber gaskets etc not exc 0.5 sqm in each pane fixed in alumuninum window, ventilator ccomplete all as specified and as directed. 101 Poly carbonate sheet not less than 3mm thick fixed in repairsfor roofing in passage complete all as specified and directed. 102 Marine plywood18-19mm thickwith bothside laminated mica sheet glossy finished (not less than 1mm) covered kitchen cabinets,inside depth not less than 0.47M , water proof, termite & Borer proof, corrosion free with melamine polished shutter and auto closer counter sunk hinges, stainless steel handles complete all as specified and as directed. Note : (i) Only front facing area of cabinet will be measured for payment(ii) Stainless steel baskets mentioned as supply only underSl. item No. 103 shall be fixed under this item as the unit rate quotedagainst this item is inclusive of this fixing provision Marine plywood complete all as specified and directed. 103 Supply only a set of stainless steel baskets with fittings as in covered kitchen cabinet as per following details :- (i) Plate basket 21x19x8- 01 No (ii) Plane basket 21x19x8 - 01 No. (iii) Plane basket 17x19x8 - 01 No. (iv) Butlery basket 17x19x4 - 01 No. (v) Cup & Saucer basket 17x19x4- 01 No. (vi) Single pull out 8 - 01 No. (vii) GT- PT & Drip tray 22 - 01 No. (viii) Telescopic channels of appropriate size as required. 104 Sink without drain board made of stainless steel 1 mm thick kitchen or laboratorywith plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm incl 40mm PTMT with coupling fixed in repairs complete all as specified and as directed. 105 Adjusting, easing and minor repairs to aluminium windows of any size, pattern and with two/three shutters & and ensuring proper functioning of the windows including changing of pivot,repairs to lock,handle,rubber beadings etcall as directed. (Note for payment purpose each shutter will be measured) 106 Taking down of existing roof treatment consisting of screed bed plaster tar felts etc including removal of PCC upto getting main roof slab and removal of dismantled materials complete all as specified and directed. 107 Cement concrete 1:2:4 (type B-0)using 12.5 mm graded stone aggregate, average. 30 mm thick as padding on roof slab complete all as specified and as directed. 108 The water proofing treatment is Seven course and shall be carried out as follows: -(i) Apply a coat of oil based bituminous primer @ 200 gram / square metre on the prepared surface.(ii) Apply a coat of blown type bitumen grade 85/25 conforming to IS:702 heated to a working temperature of 180 degree C and applied @ 1.20 Kg per square metre of the surface area.(iii) Provide and lay 4mm thick APP modified torch applied water proofing membrane weighing not less than 4.00 Kg per square meter reinforced with non woven polyester matt, weighing not less than 160gm/sqm having softening point not less than 1400C, Longitudinal tensile strength not less than 650 N/5 CM, tear strength of 180N(Min), a static puncture resistance of 180, keeping a minimum of 10 cm over laps and 15cm end lap. 109 (iv) Apply a coat of blown type bitumen grade 85/25 conforming to IS:702 heated to a working temperature of 180 degree C and applied @ 1.20 Kg per square metre of the surface area.(v) Provide and lay 4mm thick APP modified torch applied water proofing membrane weighing not less than 4.00 Kg per square meter reinforced with non woven polyester matt, weighing not less than 160gm/sqm having softening point not less than 1400C, Longitudinal tensile strength not less than 650 N/5 CM, tear strength of 180N(Min), a static puncture resistance of 180, keeping a minimum of 10 cm over laps and 15cm end lap. 110 (vi) Apply a coat of blown type bitumen grade 85/25 conforming to IS: 702 heated to a working temperature of 180 degree centigrade and applied @ 1.20 Kg /Sqm of the surface area. (vii) Finishing surface with solar reflective bituminous aluminium paint 100gm/Sqm. 111 Equipment and supervision charges for cleaning the surface using wire/ coir brush, V groove cutting along the construction joint and fill the same with crystalline modified mortar added as per manufacturer instruction. All complete as per the site conditions complete all as specified and as directed. 112 Drilling holes at specified location to required depth and diameter as directed by Engr-in-charge and injecting the two component epoxy grout as point applicable upto avg 400gm per packets fixed as per manufacturer instruction complete all as specified and as directed. 113 Micro concreting in RCC Slab/ Beams with 02 coats ofpolymer mortar of Avg thickness 20-25mm (each coat) over a coat of epoxy resin based bonding agent over two coat of zinc primertwo coats of zinc primer over a coat of epoxy bond agent including Anti-carbonation treatment for all new concrete surface protection complete all as manufacturer instruction. 114 Rendering 10 mm thick on concrete surfaces in CM 1:3 mixed with WPC as per manufacturers instructions complete all as specified and as directed by Engineer-in-charge.Note:- (i) WPC will be measured and paid seperately. (ii) Quoted rate to include for necessary scaffolding. 115 15 mm thick plaster on fair faces of brick or concrete surfaces in cement and sand mortar 1:4 finished even and smooth without using extra cement. 116 Cement concrete 1:3:6(Type C2)using 40 mm graded stone aggregate in surface channels and drains complete all as specified and as directed. 117 Providing cement concrete 1:2:4 (Type B0),using 12.5mm graded stone aggregate) as in copings and the like including weathering, slightly rounded or chamfered angles and throating all as specified andas directed. 118 Dismantling structural steel members such as channels angle iron flat etc and steel sections of any description by gas cutting or other means all as specified and directed. 119 Aluminium sheet not less than 1mm thick fixed to crumple joint with necessary fixing arragement completeall as specified and as directed.Note:- Girth & width of sheet shall be as directed by Engineer-in-charge. 120 Stainless steel alphabet of size 450mm x 300mm x 50mm made out of 0.5mm thick SS plain steel and fixed with screws on any surface complete all as specified and as directed. 121 Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and as directed. 122 100mm thick plain cement concrete1:4:8 (type D2) using 40mm graded stoneaggregate as in foundations, filling and mass concrete all as specified and as directed. 123 100 mm thick plain cement concrete 1:2:4 ( type B-2) using 40mm graded crushed stone aggregate as in hard standing, laid in alternate bays including necessary form work and finishing the surface of concrete fair and even without using extra cement complete all as specified and directed. 124 Forming 12mm thick Expansion joints filledwith pre-formed bituminous filler and top 30mm primed and sealed with sealing compound,Grade ‘A complete all as specified and directed. 125 Hardcore of broken stone of gauge n.exc 63mm deposited spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface all as specified and as directed. 126 Providing cement concrete 1:2:4 (Type B0)using 12.5mm graded stone aggregate as in kerb including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. 127 Coarse aggregate for granolithic floors graded from 12.5mm to 4.75mm spreading and levelling in layers n exc. 25 cm thick and well ramming including watering as required complete all as specified and as directed. 128 Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment complete all as specified. 129 Taking down oldangle valve and wall mixer complete all as specified and as directed. 130 Wall Mixer (3-in-1) with arrangement of both Telephonic Shower and Over Head Shower, with 210mm long bend pipe, complete all as specified and as directed. Make : CERA Model No. F1015403 or Equivalent make specified in the list of Make. 131 15 mm angle valve, half turn with flange, with flange type chromium plated for fixing accessories for CPVC pipe complete all as specified and as directed. Make : Cera Model F1015201 or or Equivalent make specified in the list of Make. 132 PVC connection pipe 16mm dia (outer 450 mm long cold water and taking down old one complete with brass union on both sides to suit 15mm GI pipe complete all as specified and as directed. 133 Taking down oldGeyser and hand over to MES store yard complete all as specified and as directed . 134 Electric water heater, storage type steel body with copper inner tank and heating element upto 1.5 KW capacity 15 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV etc. all as directed and as specified. 135 Taking down old GI/CPVC pipe of size 40 mm complete all as specified and as directed. 136 Taking down old GI/CPVC pipe of size 25 mm complete all as specified and as directed. 137 Taking down old GI/CPVC pipe of size 20 mm complete all as specified and as directed. 138 CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings 40mm dia onwall/concealed on wall, high pressure including all necessary fittings, solvents complete all as specified and as directed. 139 All as per item No 138 here-in-before but of size 25 mm dia complete all as specified and as directed. 140 All as per item No 138 here-in-before but of size 20 mm diacomplete all as specified and as directed. 141 Taking down old bib tap short body, bib tap long nose, stop cock, shower, pillar tap, sink cock, angle valve, health faucet, angle cock etc complete all as specified and as directed. 142 Bib cock, CP quarter turn with flange and aerator, fancy type short body cast copper alloy with crutch or butterfly handle screwed for GI/CPVC pipe of size 15 mm complete all as specified and as directed.Make - Cera model F-101451 or Equivalent make specified in the list of Make. 143 Bib cock, CP quarter turn with flange and aerator, fancy type long nose with wall flange cast copper alloy with crutch or butterfly handle screwed for GI/CPVC pipe of size 15 mm complete all as specified and as directed . Make - Cera model F-101452 or Equivalent make specified in the list of Make. 144 15 mm angle valve, half turn with flange, with flange type chromium plated for fixing accessories for CPVC pipe complete all as specified and as directed.Make - Cera model F-1015201 or Equivalent make specified in the list of Make. 145 Health faucet ABS body with wall hook and 1 metre SS braided connection pipe, including taking out old complete all as specified and as directed.Make - Cera model F-8030108 AB or Equivalent make specified in the list of Make. 146 Swivel overhead shower (minimum weight 40 grams) of PTMT any colour with shower arm (minimum weight 40 grams) 15mm size, 195 mm long with bend of 45 degree with flange for fixing with CPVC pipe all as specified and as directed.Make : Model No: F7020108AB of Cera or Equivalent make specified in the list of Make. 147 Taking down old CPVC ball valve of size 40mm/20mm/25mm complete all as spewcified and as directed. 148 CPVC ball valve of size 40mm suitable for CPVC pipe including necessary fittings complete all as specified and as directed.Make : SFMC/Prayag Polimer/Finolex or Equivalent make specified in the list of Make. 149 CPVC ball valve of size 25mm suitable for CPVC pipe including necessary fittings complete all as specified and as directed. Make : SFMC/Prayag Polimer/Finolex or Equivalent make specified in the list of Make. 150 Cutting and making hole for exhaust fan of sweep 300mm including marking, cutting/ breaking of any type of wall surface with appropriate tools and equipment, removing debris, making good surface to match with existing finish with all necessary scaffolding complete as directed by Engineer-in-Charge. 151 SPECIAL REPAIRS (E/M ITEMS) 152 Taking down copper/Aluminium point wiring (light, fan, socket or power) complete and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. to match with existing finish complete all as specified and as directed. 153 Taking down carefully unserviceable old switches/ sockets/ bell push/ 2 way switches, ceiling roses, pendants, regulators socketscomplete all as specified and as directed. 154 Taking down carefully old unserviceable main switches and distribution boards with fuses/ MCBs (single phase or three phase) of any capacity complete all as specified and as directed. 155 Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as specified and as directed. 156 Taking down old light fittings of any wattage all as specified and as directed. 157 Point wiring with 1.5 Sqmm PVC insulated unsheathed FRLSH multistranded single core copper conductor cable inPVC concealed conduit rigid non metallic (ISI marked) fixed concealed on wall /roof except beam, column and RCC roof including chases cutting suitable for modular switch and socket (sunken box) incl 1.5 Sqmm PVC insulated copper conductor as earth continuity wire for One light /Fan point controlled by one switch and making good disturbed surfaces of walls, floors,etc complete all as specified and as directed. Note:- Modular Box and cover plate, switches & sockets will be measured and paid separately 158 All as per item No. 157 above but for one 5 pin 5 amps socket outlet on the same board complete all as specified and as directed. 159 All as per item No 157 above but for one 5 pin 5 amps socket outlet an independent board complete all as specified and as directed. 160 All as per item No 157 above but for One bell/ buzzer point controlled by one push button complete all as specified and as directed. 161 All as per item No 157 above but for One light point controlled by two way switches complete all as specified and as directed. 162 All as per item No 157 above but with 2.5 Sqmm copper conductor including 2.5 Sqmm copper cable on earth wire for one 6 Pin 16 Amps Socket outlet independent board complete all as specified and as directed. 163 All as per item No 157 above but with 4 Sqmm copper conductor including 4.0 Sqmm copper cable on earth wire for sheet metal enclosure complete all as specified and as directed. 164 Modular switch 1 way 6 Amps,1module typecomplete all as specified and as directed. 165 Socket modular 6 Amps and 2/3 pin combined 2 module complete all as specified and as directed. 166 Switch 16 A One way SP modular type complete all as specified and as directed. 167 Modular socket6 A/16 A - 2/3 pin combined 2 module complete all as specified and as directed. 168 Bell push, Modular, 5 amp one way complete all as specified and as directed. 169 Modular switch 6A two waywith cover plate complete all as specified and as directed. 170 TV Socket 1 Module along with cover plate and metal box complete all as specified and as directed. 171 RJ45 Cat 6 socket, 1Module cover plate with frame 1 Module all as specified and as directed. 172 Modular cover plate with frame 1 Module including replacement of existing complete all as specified and as directed. 173 Modular cover plate with frame 2 Module including replacement of existing complete all as specified and as directed. 174 Modular cover plate with frame 3 Module including replacement of existing complete all as specified and as directed. 175 Modular cover plate with frame 4 Module including replacement of existing complete all as specified and as directed. 176 Modular cover plate with frame 6 Module including replacement of existing complete all as specified and as directed. 177 Modular cover plate with frame 12 Module including replacement of existing complete all as specified and as directed. 178 Modular metal flux box 1/2 Module including replacement of existing complete all as specified and as directed. 179 Modular metal flux box 3 Module including replacement of existing complete all as specified and as directed. 180 Modular metal flux box 4 Module including replacement of existing complete all as specified and as directed. 181 Modular metal flux box 6 Module including replacement of existing complete all as specified and as directed. 182 Modular metal flux box 12 Module including replacement of existing complete all as specified and as directed. 183 Ceiling rose surface bakelite 65 x 50mm 3 terminals complete all as specified and as directed. 184 Buzzer, Ding Dong AC. 230 volts, single pole complete all as specified and as directed. 185 Fan step regulator, 120W, 2 module complete all as specified and as directed. 186 Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. 187 Batten for LED tube lights, 4 feet, both side connection type including LED tube rod 1 x 20 Watt, both side connection with luminous efficacy of min 100 Im/watt complete all as specified and as directed.Make: Havells Cat part No LHEXAZP7IN1W020 or equivalent 188 Indoor LED wall light 7W, complete all as specified and directed by Engineer-in-charge. Make: LUKERCat part no: MAIRA GPS1 LWL 110-01 or equivalent any other make in the approve price list 189 2 FeetLED 1 x 10W Watt, with luminous efficacy of minimum 100 Lumen/Watt, Wall/Surface mounted luminaries with engineering plastic housing, wired with all accessories complete incl provn of flexible copper wire from ceiling rose to light fitting terminal. 190 Building security light made up of pressure die cast housing with toughened glass and high power LEDs with option of secondary optic with IP 66 protection of 45 Watt, with luminous efficacy min 100 lumen/watt Crompton Cat Part No. LSTS-30-CDL/NL-M or other manufacturers in the approved price list including suitable GI bracket of 40 mm dia and fixing arrangement on walls complete all as specified and as directed by Engineer-in-Charge including taking down of existing light fitting of any type and make. 191 Round shape 12 watt 220 volts AC, surface mounted type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete. 192 Taking down ceiling fan, Painting of ceiling fans complete, including taking down rods in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and hanging in original as directed position and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and as directed. 193 Replacement of Ceiling fans, complete with blades, down rods, accessories 230V, 1200mm sweep, with min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current (BLDC) including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and as directed. Make Atoberg Cat Part No. AMEZA/Orient Model Ecotech Neu BLDC 5 star/Havells Cat Part No. Efficiencia Neo or Equivalent make specified in the approved list of make.Note :- Old Ceiling fans to be deposite at AGE E/M (NW) store yard. 194 Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 900, single phase, Copper winding of sweep 300MM including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and directed.Note :-Old exhaust fans to be deposite at AGE E/M (NW) store yard. 195 Exhaust fan steel body heavy duty with louvers complete of sweep size 300mm, 900 RPM, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and directed.Note : Old exhaust fans to be deposited at AGE E/M (NW) store yard. 196 SPN enclosure withtwo pin and earth plug and socket complete with one SP MCB, 20 Amps having breaking capacity 10 kA,including taking down old unserviceable eath plug complete all as specified and as directed by Engineer-in-Charge. 197 Sheet metal enclosureTPNDBwhen MCBs to be used 4 way with 200 amps bus bardouble door, complete all as specified and as directed by Engineer-in-Charge. Make of DBs & MCBs : Legrand/ L&T/ Schneider or equivalent make in the approved manufactures list. 198 Sheet metal enclosureSPNDBwhen MCBs to be used 8 way with 200 amps bus bardouble door, complete all as specified and as directed. 199 MCB 415V 10KA C curve 63 AMP TPN miniature circuit breakerof following poles and current carrying capacity in the DB including replacement of existing one complete with connection testing and commissioning all as specified and as directed. 200 MCB SPN, 32Amps, 240 volts, C series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning all as specified. 201 MCB SP, 6A-32 Amps, 240 volts, C series, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning all as specified. 202 MCB 415V 10KA C curve 63 AMP TP miniature circuit breakerof following poles and current carrying capacity in the LT Panel complete with connection testing and commissioning. 203 Sub main wiring using proper colour coding 1100 Volts grade with 4 runs of 10 Sqmm (FRLSH) grade PVC insulated unsheathed multistranded copper conductor cable and 1 run of 10 Sqmm (FRLSH) cable as earth continuity wire drawn through and including rigid non metallic PVC conduit medium grade not less than 25 mm dia with all conduit accessories on surface or concealed as required in floor/wall/ ceiling complete all as specified and as directed by Engineer-in-Charge.Note - (a) 4 runs of 10 Sqmm sub main wire and one run of 10 sq mm submain wire for earthing and PVC conduit pipe with accessories shall be measured as one unit. (b) Chase cutting for concealing will be measured and paid separately. 204 sub main wiring using proper colour coding 1100 Volts grade with 4 runs of 6 Sqmm (FRLSH) grade PVC insulated unsheathed multistranded copper conductor cable and 1 run of 6 Sqmm (FRLSH) cable as earth continuity wire drawn through and including rigid non metallic PVC conduit medium grade not less than 25 mm dia with all conduit accessories in surface or concealed as required in wall/floor/ceiling complete all as specified and as directed by Engineer-in-Charge.Note - (a) 4 runs of 6 Sqmm sub main wire and one run of 6 sq mm submain wire for earthing and PVC conduit pipe with accessories shall be measured as one unit. (b) Chase cutting for concealing will be measured and paid separately. 205 sub main wiring using proper colour coding 1100 Volts grade with 2 runs of 6 Sqmm (FRLSH) grade PVC insulated unsheathed multistranded copper conductor cable and 1 run of 6 Sqmm (FRLSH) cable as earth continuity wire drawn through and including rigid non metallic PVC conduit medium grade not less than 25 mm dia with all conduit accessories in surface or concealed as required in wall/ ceiling/ floor all as specified and as directed by Engineer-in-Charge.Note - (a) 2 runs of 6 Sqmm sub main wire and one run of 6 sq mm submain wire for earthing and PVC conduit pipe with accessories shall be measured as one unit. (b) Chase cutting for concealing will be measured and paid separately. 206 Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below normal ground level surrounded from all side by 15 cm of thick and packed layers of charcoal dust and common salt, filling alternate layers and electrode connected by using Gl strip 25x 4 mm (max -length of 7.5 mtrs) by means of bolts, nut and washer of Gl and providing GI light grade pipe 40 mm dia as protection pipe for GI strip connected main control board / test point and provided with GI pipe of light grade 20 mm bore for watering and including funnel, wire mesh PCC chamber of 1:3:6 type C1,and RCC cover of 1:2:4 type B1 including necessary earth work in any type of soil /strata disposal of soil complete and shown in electrical plate No. 3 of SSR part -1 including testing on completion all as specified and as directed by Engineer-in-Charge. 207 MCCB 4 Pole 415 V adjustable type, 200 Amps with breaking capacity 36 KAinc;luding taking down of existing one complete all as specified and as specified. 208 Cleaning the LT panel, preparation of old painted surface by scrubbing out the old paint, spray paintingtwo coats of synthetic enamel paint of colour matching the existing paint over a coat of red oxide primer along with welding/ cutting/ modifying where ever required along with installation of multifunction meter, Energy meter and indication lamps all as specified and as directed. 209 Cutting chases for sub main wiring, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth all as directed and as specified. 210 Supply and laying GI Strip of size 25 x 4 mm including taking down old strip all as directed and as specified.
