|
| 1 | M&L for preparation of roof surface and application of Dr fixit roof seal first coat of prime seal with 50% dilution, adequate time for drying. 1st coat of Dr fixit roofseal ultra undiluted. A glass fiber mesh of 2.5mm x 2.5mm needs to be sandwiched between the first coat and second coats. Then 2nd coat of Dr fixit roofseal ultra is applied to the first coat @ 1.4 ltrs/Sq mtr. complete all as specified and directed. Note:- work will be completed at various location in patch repair basis, glass fiber mesh will be paid separately. |
| 2 | M&L for glass fiber mesh of 2.5mm x 2.5mm, thickness of the material should not be less than 1mm or as specified by manufacturercomplete all as specified and directed. |
| 3 | M&L gunniting to RCC works in column ,beams, slabs, landing, chhaja, balconies etc by removing loose concrete including plaster cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick to rusted steel reinforcement after removing/ cleaning all rust by sand/grit blasting and supply and fixing welded steel wire mesh 75mm x 75mm with 3mm dia steel wire as facies/drops and similar works etc and expoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sika.Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 2% by weight of cement polycrete and providing gunniting with a minimum pressure of 2.5 Kg/sqcm and applying 25mm thick layers of gunniting in cement mortar (1:2) using ordinary port landcement of 43 grade over wherever required complete all as specified and directed.Note:- (i) Contractor should visit the site before quoting the price as Cost of dimentling and refixing of existing false ceiling including electrical fitting or any services is deemed to be included in quoted rate (ii) After placing the additional reinforcement all concrete surface shall be throughly scrubbing with brushed washed with water and allow dry and plaster complete all as specified. (ii)Work to be carried out as in patches as directed by Engr-in-charge.(iii)Rate for scaffolding ,15mm thick plaster in CM 1:4 and TMT bars (where applicable) deemed to be included in quoated rate. (iv) preparation of surface and applying two coat of OBD with one coat of primer over 1mm thick wall care putty, including cleaning of entire room after completion of work deemed to be included in this item. |
| 4 | Dismantiling of Asbestos cement (corrugated, semicorrugated, etc.) ofroof coverings including ridge, hips, valley gutters etc complete all as specified and as directed. |
| 5 | Dismantling of wooden fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section of any description at any position not otherwise provided for complete all as specified and directed. |
| 6 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strenght of 550 Mpa as in roof covering/ cladding to wall of any height , fixed with self tapping screwsasrequired comlplete all as specified and directed. |
| 7 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strenght of 550 Mpa as in roof covering/ cladding to wall of any height , fixed with self tapping screwsasrequired comlplete all as specified and directed. |
| 8 | S&F SS Multipurpose cloth hook-6 hook door wall hook hanger for bathroom cloth hook Matt Finish complete all as specified anddirected. |
| 9 | M&L PCC 1:3:6 type C2 (using 40mm graded stone aggregate as infoundations, filling and mass concretecomplete all as specified and directed. |
| 10 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanksand similar work conforming to Fe.290.Gde-E-165complete all as specified and directed. |
| 11 | S& F Mild steel angle iron cut to shape as directed drilling holes notching for wire as in wind ties for roof including securing bolts etc including all necessary cutting and welding for similar work upto any ht of bldg complete all as specified and directed. |
| 12 | M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described and applying Two coat of Synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 13 | Taking down GI pipe of any grade of 15mm bore including fittings and connections including cleaning for refixing or removal to store all as specified and as directed. |
| 14 | Taking down GI pipe of any grade of 20mm bore including fittings and connections including cleaning for refixing or removal to store all as specified and as directed. |
| 15 | Taking up or down 25mm or 32mm boresteel tubing including fittings and connections including cleaning for refixing or removal to store all as specified and as directed. |
| 16 | S&F steel water tubing medium grade galvanized with all fittings and fixed complete to walls, ceilings or laid on floors, bore of tube 15mm complete all as specified and directed. |
| 17 | S&F steel water tubing medium grade galvanized with all fittings and fixed complete to walls, ceilings or laid on floors, bore of tube 20 mm complete all as specified and directed. |
| 18 | S&F for 25mm bore steel water tubes, \"medium grade\" galvanised, with and including all fitting and fixed complete to walls and ceilings or laid in floorscomplete all as specified and as directed |
| 19 | S & F in repairsPVC valveless, syphonic action type, low level PVC flushing cistren (dual flush) of 10 ltr capacity,white with flush pipe & all fitting complete all as specified and directed. |
| 20 | S&F in repair 15 mm bore bib taps fancy type ,chromium plated,long neck cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrulecomplete all as specified and directed. |
| 21 | S&F in repair 15mm dia,stop valve fancy type,cast copper alloy,chromium plated,screwed down high pressure, with crutch or butterfly handles for 15 mm bore pipe or for unionscomplete all as specified and directed. |
| 22 | S&F in repair 15mm dia,stop valve fancy type with long shank and cup (concealed type),cast copper alloy,chromium plated,screwed down high pressure, with crutch or butterfly handles for 15 mm bore pipe or for unionscomplete all as specified and directed. |
| 23 | S & F in repair 15 mm bore swan neck pillar tap fancy type , cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe all as specified and directed. |
| 24 | S&F in repair CP wall mixer for mixing Hot & cold water screwed down for iron pipe 15mm bore complete all as specified and directed. |
| 25 | S&F in repair CP wash basin mixture fancy type, with capstan heads, chromium plated, screwed down for high pressure with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly nuts screwed for 15mm iron pipe and fixed comple all as specified and directed . |
| 26 | S&F in repair 25mm dia PTMT ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed.(min wt- 455 gms), complete all as specified and directed. |
| 27 | S&F in repair 20mm dia PTMT ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed.(min wt- 210 gms), complete all as specified and directed. |
| 28 | S&F in repair 15mm dia PTMT ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed.(min wt- 142 gms), complete all as specified and directed. |
| 29 | S&F in repair chromium plated soap dish,fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 30 | S&F in repair gratings of 100mm dia made of stainless steel with waste hole complete all as specified and directed |
| 31 | S&F in repair gratings of 125mm dia made of stainless steel with waste hole complete all as specified and directed |
| 32 | S&F in repair Chromium plated shower rose with shower arm round 100mm ABS full chrome with min arm 225 mm with or without swivel joints, any size, includingfixing with GI pipe of 15 mm bore complete all as specified and directed. |
| 33 | S&F in repair 6mm thick lookingmirror fixed to wall with stainless steel plug/ connector/ spacers/ screws etc. chrome finish polished, bevelled edge etc.complete all as specified and directed |
| 34 | S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 35 | S&F in repair Chromium plated Health Faucet for bore size 15mm (flexible tube and hand shower) ,wall mounting type suitable for EWC; with CP nuts and washer incl square hook ABS ,of length 900mm complete all as specified and directed. |
| 36 | S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 6 cm wide complete all as specified and directed. |
| 37 | Disconnecting existing water tank setting aside ( or lowering if required ) for repairs cleaning etc and hoisting if required reconnecting and re-fixing in position including cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc capacity exc 250 ltr but n.exc 500 ltrs, complete all as specified and as directed. |
| 38 | Description all as per item No 37 above but capacity exc 500 ltr but n.exc 1000 ltrs and ditto |
| 39 | Description all as per item No 37 above but capacity exc 1000 ltr but n.exc 2000 ltrs and ditto |
| 40 | Dismantling PVC water tanks of capacity exc 250 ltrs but n.exc 500 ltrs in any position and removing from sitecomplete all as specified and as directed. |
| 41 | Description all as per item No 40 above but capacity exc 500 ltr but n.exc 1000 ltrs. |
| 42 | S&F tripple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I of 500 ltrs capacitywith & including 20mm dia PTMT float valve complete all as specified and directed. |
| 43 | S&F tripple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I of 1000 ltrs capacitywith & including 20mm dia PTMT float valve complete all as specified and directed. |
| 44 | S&F in repair wash basin waste coupling 32 mm dia of CP (half or full threaded) Minimum weight 45gms complete all as specified and directed. |
| 45 | S&F in repair sink waste coupling 40 mm dia of CP (half or full threaded) Minimum weight 60 gms complete all as specified and directed. |
| 46 | S & F in repair flexible PVC waste pipe of 32 mm dia, 600 mm long complete all as specified and directed. |
| 47 | S&F in repair 160mm diaPVC (SWR) pipes single socketed, in any length, laid in trenches or in floors / fixed to walls with and including stack clamps complete all as specified and as directed |
| 48 | S&F in repair 110mm diaPVC (SWR) pipes single socketed, in any length, laid in trenches or in floors / fixed to walls with and including stack clamps complete all as specified and as directed |
| 49 | S&F in repair 75mm diaPVC (SWR) pipes single socketed, in any length fixed to walls / floors or in trencheswith and including stack clamps complete all as specified and as directed |
| 50 | S & F in repair bend suitable for 160mm dia PVC (SWR) pipe complete all as specified and as directed |
| 51 | S & F in repair bend suitable for 110mm dia PVC (SWR) pipe complete all as specified and as directed |
| 52 | S & F in repairs bend suitable for 75mm dia PVC (SWR) pipe complete all as specified and as directed |
| 53 | S&F in repair chromium plated Toilet paper holder incl movable flap and fixed to walls with chromium platedbrass screws complete all as specified and directed. |
| 54 | S&F in repair vitreous chinawash hand basin, white, (flat back or angle back type) of size 580x450 mm including supplied and fixing angle iron bracket and CP Pillar tap fancy type 15 mm bore,CP waste coupling, PVC waste pipe 32 mm dia, and 01 No PVC connection 15 mm dia & 450 mm long complete all as specified and directed. |
| 55 | S&F in repair sink without drainage board made of stainless steel 1 mm thick with plug and washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe overall size 915x460 mm and bowl size 410x330x160 mm complete all as specified and directed. |
| 56 | S&F in repair sink with drainage board made of stainless steel 1 mm thick with plug and washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe overall size 915x460 mm and bowl size 410x330x160 mm complete all as specified and directed. |
| 57 | S&F in repairs vitreous china squatting pan orissa pattern of size 580mm x 440mm, white with \"P\" or \"S\" trap front of back inlet and integral foot rest complete all as specified and directed. |
| 58 | S&F in repair vitreous china wash down water closet pan pedestal pattern white with and including fixing bolts, flushing cistern, flush pipe, PVC connection complete all as specified and directed. |
| 59 | S&F in repair plastic seat cover for EWC with & including hinging device complete all as specified and directed. |
| 60 | Taking down cement / lime plaster of any description on brick work or stone walls etc including racking out joints hacking for key scrubbing down with water etc.complete all as specified and as directed |
| 61 | M&L for rendering 15mm thick in cement mortar 1:4 onfair faces of brick work/concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 62 | M&L for rendering 15mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces finished the surface enen and smooth without using extra cement complete all as specified and directed |
| 63 | M&L for rendering 10mm thick in CM 1:3 on concrete surfaces in ceilings comple all as specified and directed . |
| 64 | M&L forpreparation of new plastered surfaces of Wall and applying two coats of weather proof exterior emulsion paint in normal pattern , over a coat of primeras per manufacturers instructions complete all as specified and as directed. |
| 65 | M&L for two coats of distemper oil emulsion over newely plastered surfaces of wallincluding preparation of surfaces complete all as specified and directed. |
| 66 | M&L for preparation of newly plastered surface of ceiling and applying two coats of white wash complete all as specified and directed. |
| 67 | M&L for welding in repair exc 2.5 cm but n.exc 5cm in length, thickness of metal to be welded n.exc 6mm complete all as specified and directed. |
| 68 | S&F in repairs CP tubular towel rail 20mm dia, D type, 600mm long between flanges complete all as specified and directed . |
| 69 | S&F in repairs 15mm bore CP angle stop valve screwed for iron pipe and fixed in position complete all as specified and directed. |
| 70 | S&F in repair urinal spreader of Chromium Plated any colour for fixing with 15 mm dia pipe. (Minimum weight 100gms) complete all as specified and as directed. |
| 71 | S&F in repair vitreous china urinal full stall type flat back size ofwhite with grating and union for discharge pipe including chromium plated water spreader, connection pipe and discharge down pipe complete all as specified and as directed |
| 72 | S&F in repair CI brackets for WHB, of angle iron 35mm x 35mm x 5mm of required length with and including embedding in PCC 1:2:4 type B1 and two coats of painting with synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 73 | Demolition of cement concrete (unreinforced) in ground floor and pavingexc. 15 cm thickness (below or above ground level) complete all as specified and as directed |
| 74 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided forcomplete all as specified and as directed |
| 75 | M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base of floor etc complete all as specified and as directed |
| 76 | M&L for 25mm thick sand cushioning laid dry to the profile under interlocking block including watering and well ramming complete all as specified and as directed |
| 77 | M&L for machine pressed precast concrete interlocking paver block of approved shape and size of 60 mm thickness using grey cement and pigment , with minimum compressive strength of 35 N / Sqmm (M-35 grade), without correction factor for chamfering, made in rubber moulds with 0.50 mm thick scratch proof lacquer coating on top surface complete all as specified and as directed |
| 78 | M&L for 100mm thick PCC (1:3:6) type C2 using 20mm graded stone aggregate as in sub base of floor etc complete all as specified and as directed |
| 79 | M&L for chequered cement concrete tile 20cmx20cmx25mm thick, set jointed and pointed in neat cement slurry in floors and including 20mm thick screed bed in CM (1:6) of approved colour and pointing with grey cement and pigment complete all as specified and directed. |
| 80 | M&L for out door colouredindustrial tiles, textured surfaces with high skid resistance, scratch resistant, impact resistant, joint free (edge cut) of size 300 mm x 300 mm x 8 to 10 mm thick as in floors etc laid over with and including 15 mm thick screed bed or bedding layer in CM (1:6), set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and as directed |
| 81 | M&L for Filleting in any position and any shape in CM (1:4) including all mitres, stops, etc. exc. 25sqcm but n.exc 50 sqcm including for fair finish to exposed surfaces complete all as specified and as directed. |
| 82 | Dismantling floor,hearth or wall tiling including cement mortar bedding and removing rubbish off the premisescomplete all as specified and as directed |
| 83 | M&L for 25 mm thick PCC 1:2:4, type B0 (using 12.5 mm graded stone aggregate) as in flooring in leveling course complete all as specified and as directed |
| 84 | M&L for light shade vitrified ceramic tiles, joint free (edge cut) coloured , 9 to 10mm thick (square/ rectangular) polished, area of each tile n.exc 0.36 sqm, in floors etclaid over with and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tilescomplete all as specified and directed. |
| 85 | M&L for light shade vitrified ceramic tiles, joint free (edge cut) coloured , 9 to 10mm thick (square/ rectangular) polished, area of each tile n.exc 0.36 sqm, in vertical surfaces etc laid over with and including 10 mm thick rendering for backing layer in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured cement to match the tilescomplete all as specified and directed. |
| 86 | M&L for Non skid, joint free (edge cut) coloured ceramic tiles 7 to 8 mm thick (Square / rectangular) polished area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc laid over with and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tilescomplete all as specified and directed. |
| 87 | M&L for Non skid, joint free (edge cut) coloured ceramic tiles 7 to 8 mm thick (Square / rectangular) polished area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in vertical surfaces laid over with and including 10 mm thick rendering for backing layer in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured cement to match the tilescomplete all as specified and directed. |
| 88 | M&L for Non skid, joint free (edge cut) coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of eachtile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchas in floors etc laid over with and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tilescomplete all as specified and directed. |
| 89 | M&L for machine cutkota stone slab flooring18 to 20mm thick over cement screedbase laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete with and including 20mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 90 | M&L for machine cutkota stone slab 18 to 20mm thick as in dado, riser, steps and the likes laid over with and including rendering 15mm thick in CM 1:4 for bedding layer complete all as specified and as directed. |
| 91 | M&L for kota stone slab flooring rubbing and mirror polishing onlywith required blade complete all as specified and as directed. |
| 92 | M&L for 16 mm to 18 mm thick Granite telephonic black (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, oval shape WHB, wall claddings and the likes; in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.. |
| 93 | M&L for glazed ceramic coloured tiles 300x450x 7mm thick as in dadowith and including 10mm thick rendering for bedding layer in CM 1:4, set and jointed in neat cement slurry and pointed with white cement complete all as specified and as directed. |
| 94 | Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and as directed. |
| 95 | M & Lfor brickwork with subclass `B\" bricks (using old size bricks), straight or curved on plan exc 6m mean radius, built in CM 1: 6 all as specified and as directed. |
| 96 | All as per item No 95 above but except brickscomplete all as specified and directed. |
| 97 | M&L for Providing cement concrete type B-1, 1:2:4 (using 20mm graded stoneaggregate) as in copings, bed plates, kerbs etc including weathering, slightly rounded or chamfered angles and throating as directed |
| 98 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards any thickness and in any position including cover fillets complete all as specified and directed. |
| 99 | M&L for GI powder coated snap grid frame work forfalse ceiling of approved (ISI marked) make fixed togalvanised iron steel angle grid 600x600mm size suspended system fixed to GI framed work with main runner (32x24x6.5)mm cross tee (27x24x2.5)mm and moulding (19x19)mm of approved make and section as specified in SSR Part II with suitable hook/fasteners and GI/aluminium suspenders not less than 4mm dia upto 1200mm length @ 1.00m C/C minimum. ceiling system is to be fixed in water level without any sag including ceiling cleats made out of GI flat iron 40x3mm size 60mm long and expansion hold fastner 12.5 mm dia 40mm long complete all as specified and directed. |
| 100 | S&F HPSC pre prime non asbestos fiber cement building board 4mm thick size 595x595mm with decorative finish fixed to GI powder coated snap grid frame work with screw in ceiling complete all as specified and directed. |
| 101 | M&L for solid PVC wall Panelling consisting of 5.00mm thick single side prelaminated PVC sheet inclusive of solvent cement and fixing at site on PVC frame including taking down of existing switch board tube light fitting and re-fixing complete all as specified and as directed. Note:- The quoted rate shall include taking down of existing switch board/ tube light and refixing the same at same location after carring out wall panelling work. |
| 102 | S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on wall to make PVC frame complete all as specified anddirected |
| 103 | S&F PVC beading fix with adhesive paste all as per manufacturer\"s instructions complete all as specified and directed |
| 104 | S&F in repair venetian blinds in double layers roller type of approved colour including all accessories, fitting/fixtures requiredfor fixing the same in windows complete all as specified and as directed. |
| 105 | Taking down door chowkhat with shutter area n.exc 1.5 Sqmeach (without taking off shutters from the frame) including making good of jambs with cement mortar 1:4 etc complete all as specified and as directed. |
| 106 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specification and shown in drg in SSR Part -II 2020 complete all as specified and as directed |
| 107 | S&F factory made solid panel PVC door moulded shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain cover PVC \"C\" channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles and rails with suitable PVC sheet beadingand jointed together with solvent cement as per specification and drg shownin SSR Part -II 2020 complete all as specified and as directed |
| 108 | S&F stainless steel finished butt hingesmedium weight cold rolled of size 100mm complete all as specified and as directed. |
| 109 | S&F 100 mm long alluminium anodised tower bolt of extruded section complete all as specified and as directed |
| 110 | S & F of aluminium alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed. |
| 111 | S&F 100 mm long extruded alluminium alloy handle fabricatedtype anodised complete all as specified and as directed |
| 112 | Providing and fixing factory made uPVC any colour casement (Openable) Door made of extruded profile with wall thickness of 2.3mm ( + 0.2mm). Window profile with hollow section with multichambered, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + 0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 8mm thick toughened glass etc complete all as specified and directed by Engr in Charge. Note- rate quoted by contractor shall include, the cost of 8 mm thick toughened glass,taking down old door and other connected accesseories complete all as specified and as directed |
| 113 | Supply and fixing factory made uPVC white colour Two/three track two/three panels sliding window upto 1.50 m height made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 + 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware’s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately)Note: For UPVC frame and sash extruded profiles minus 5 % tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 114 | Taking down old steel/wooden windows with holdfast & making good surface to match with the existing and S&F windows/ ventilators fabricated from 0.6mm thick roll formed section made of galvanised steel powder coated (Base steel as per IS- 513 \"D\" quality) galvanised as per IS-277 with Zinc of 120 gm/sqm. Windows/ventilators having frame suitable for dual shutter i.e. inner and outer shutter with grill, glazed shutter with 4.0 mm thick glass, mesh shutter with 32 gauge stainless steel mesh, 6mm x 12mm flat iron with 10mm square bar MS grill and all fitting, fixtures accessories complete all as specified and shown in drawing no CEAF/STD-191/2014 Sheet 1/2 & 2/2 (4000 Series) NOTE:The quoted rate shall be deemed to be included the following:- (i) Glazed shutter with 4.00 mm thick glass, mesh shutter with 32 gauge stainless mesh and MS grill as per above mentioned drawing is deemed to be inclusive in the rate quoted.(ii) Glass, stainless steel mesh will be fixed to window by authorised rep of manufacturer of window only.(iii) Taking down old window making good of jambs in CM (1:4) and applying OBD in two coats includingwith putty complete. |
