Tender For Construction Of Govt High School Kalyanpur, Block Jakhora Lalitpur Under Rastriya Madhyamik Siksha Abhiyan
Tender Value
Ref. Documents
Estimated cost
Bid Submission
09 Oct 2025
0 days left
EMD
2 Lakhs
Bank guarantee accepted
Document Fee
2360
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kalyanpur → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Govt High School Kalyanpur, Block Jakhora Lalitpur Under Rastriya Madhyamik Siksha Abhiyan
BOQ
| Sl. No. | Item Description |
| 1 | High School building |
| 2 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out thexcavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 4 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming andwatering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 5 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 6 | Cement concrete in 1:4:8 with cement, sand and 4cm .(1.5\") gauge Approved granite stone ballast (crusher broken) in foundation including supply of all materials, labours and T&P etc. required for proper completion of work. |
| 7 | R.C.R Stone Masonery work in foundation in1:6 cement :sand mortar |
| 8 | M 150 brick work in 1:6 cement and Coarse fine sand mortor in foundation and plinth i/c all complete as chapter 6 as S.I. No 303 |
| 9 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) Footing |
| 10 | Providing and injecting chemical for pre-constructional anti-termite treatment and chemical barrier underand around the coloumn pits wall trenches basement excavation top surfaces if plinth filling junction of wall and floor, along the external per meter of binding expansion joints surrounding of pipes and conduit etc, complete . |
| 11 | R.C.C work in 1:1½:3 cement approved coarse sand and 20 mm gauge granite stone gritt for Plinth Beam excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc. also including supply of all materials,labour and T&P etc. required for proper completion of the work .Binding wire cost being included in the item. |
| 12 | Providing and laying damp proof course 2.5 cm thick with cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 10 mm ) and curing complete |
| 13 | 12 mm cement plaster on roung side of single or half brick wall finished with a floating coat of neat cement of mix.1:4 (1 cement :4 fine sand) |
| 14 | Providing & applying a coatof residual petoleum bitumen of grade of vg-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a plece of cloth lightly soaked in kerosene oil. |
| 15 | Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal sizeLintel Band |
| 16 | Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal sizeR.C.C Work in Slab |
| 17 | Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal sizeR.C.C work in beam |
| 18 | Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal sizeR.C.C Columm |
| 19 | M 150 brick work in 1:6 cement and Coarse sand ofmortor in s/s in one brick thick wall including supply of all materials , labours and T&P etc. required for proper completion of the work. |
| 20 | 115 mm brick work in 1:4 cement and Coarse sand ofmortor in s/s in one brick thick wall including supply of all materials , labours and T&P etc. required for proper completion of the work. |
| 21 | Mild steel or iron in plain work such as reinforced concrete wrought to required same as necessary including bending for proper completion of the work. |
| 22 | 15mm thick plasterin 1:6cement mortar over brick work minimum thickness not to be less than 3/6”(12mm) thick including supply of all materials labour and T&P etc. required for proper completion of the work for proper completion of the work but with cement and approved coarse sand in 1:6 cement & fine sand of 1.25 F.M. mortar.in external |
| 23 | 12mm thick plasterin 1:6cement mortar over brick work minimum thickness not to be less than 3/6”(12mm) thick including supply of all materials labour and T&P etc. required for proper completion of the work for proper completion of the work but with cement and approved coarse sand in 1:6 cement & fine sand of 1.25 F.M. mortar.inwall. |
| 24 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete |
| 25 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete |
| 26 | Provinding and laying caremic glazed floor tiles of the 300x300 mm (thickness to be specified by the manufacture) of 1st quality conforming to IS: 15622 of approved make in colour such as white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4(1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching plehment etc |
| 27 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of stepsand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 28 | Kota stone flooring over 20mm (average) thick base laid over kounted with grey cement slurry mixed with pigment to math the shede of the slab, including rubbing and plishing complete with vase of cement mortar 1:4(1cement :4 coarse sand) 25 mm thick |
| 29 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillarslaid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarsesand) and jointed with grey cement slurry mixed with pigment to matchthe shade of the slabs, including rubbing and polishing complete. |
| 30 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab |
| 31 | Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanitycounters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm(Granite of any shade) |
| 32 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on bothfaces of shutters:(a) single leaf- (35mm thick) |
| 33 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters: (b) Double leaf- (35mm thick) |
| 34 | Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage includingcost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Providing & fixing of doors / windows grill |
| 35 | Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage includingcost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Z- Section Steel windows |
| 36 | Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage includingcost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Angle iron door Chaukhats |
| 37 | Distempering ( two coat) with oil bound distemper of approved beand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer or approved brand & manufacture such as berger, j&N, Shalimar, asian paints after thoroughly brushing the suface from mortar droppongs & other foreign matters & also including preparing the surface material & sand papered smooth including cost of all material |
| 38 | Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 39 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 40 | Providing and laying \"brick coba\" 120 mm thick laid with M-150 class brick bat coba 7.50cm thick with gap of 15mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with acrelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand finised smooth & top mashed false square 30 cm x 30 cm and side wall parapet shall be mono tythic plaster wall up to 30 cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonany Coba with top finised plaster mixed with acetic water proofing compound @ 2% by weight & including s/o all material, labour, T& P etc complete for proper completion of work. |
| 41 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 42 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 43 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete. With 4.0 mm thick glass panes |
| 44 | Providing and fixing in posltion collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail ofl T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handies, including applying a priming coat of |
| 45 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) |
| 46 | Centering & shuttering including strutting, propping etc.and removal of form for all heights: Suspended floors, roofs, landings, balconies and access platform. |
| 47 | Centering & shuttering including strutting, propping etc.and removal of form for all heights: Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 48 | Centering & shuttering including strutting, propping etc.and removal of form for all heights: Columns,Pillars, Piers, Abutments, Posts and Struts. |
| 49 | Providing and fixing U. p.v.c rain water pipe 110mm dia with shoe,door bend etc. |
| 50 | Providing and fixing of wall face unplastiside PVC mold fitting accessories for unplastiside rigid PVC rain water pipe coforming including joint with seal ring conforming to leaving 10 mm gap to thermal expension Cuppler (110 mm) |
| 51 | Providing and fixing of wall face unplastiside PVC mold fitting accessories for unplastiside rigid PVC rain water pipe coforming including joint with seal ring conforming to leaving 10 mm gap to thermal expension Single Tee without door |
| 52 | Providing and fixing of wall face unplastiside PVC mold fitting accessories for unplastiside rigid PVC rain water pipe coforming including joint with seal ring conforming to leaving 10 mm gap to thermal expension Bend 87.5 degree (110 mm) |
| 53 | Providing and fixing of wall face unplastiside PVC mold fitting accessories for unplastiside rigid PVC rain water pipe coforming including joint with seal ring conforming to leaving 10 mm gap to thermal expension Shoe Plain (110 mm) |
| 54 | Appron Work |
| 55 | Supply and filling of Moorum soil in plinth protection /appron |
| 56 | Brick work in 1:6 cement:sand moratr in Appron |
| 57 | Lean concrete in 1:4;8 in appron |
| 58 | 25 mm p.c.c.flooring in 1:2;4 |
| 59 | Providing & fixing Glass sttirups in flooring |
| 60 | Door Fitting |
| 61 | Providing and fixing I.S.I. mark oxidised M.S. tower bolt finish (Barrel type) with necessary screw etc complete (150 x 100 mm) |
| 62 | Providing and fixing I.S.I. mark oxidised M.S. Sliding door bolt with nut and screw etc complete (250 x 16 mm) |
| 63 | Providing and fixing I.S.I. mark oxidised M.S. Handles conforming to with nut and screw etc complete (100 mm) |
| 64 | Appron Drain |
| 65 | Earth work in exacavation in trenches for foundations land for pipes cables etc. in ordinary soil (loan clay or sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand disposal of surplusexcavated earth as directed by the Engineer i/c with in a lead of 50m. |
| 66 | Providing and laying in cement concrete 1:4:8(1 cement :4coarse sand :8 graded stoneaggregate 40 mm nominal size) and curing complete, including cost of form-work, in foundation and floors. |
| 67 | Class 150 Brick Work in1:4 cement and coarsesandof2.20fineness modulus mortar infoundation and plinth including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. |
| 68 | 12MM Th. Cement plaster 1:3 (cement & C.sand) with Neat Cement Finish |
| 69 | Toilet Block Ground Floor |
| 70 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 71 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out thexcavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 72 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming andwatering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 73 | Cement concrete in 1:4:8 with cement, sand and 4cm .(1.5\") gauge Approved granite stone ballast (crusher broken) in foundation including supply of all materials, labours and T&P etc. required for proper completion of work. |
| 74 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 75 | Providing and injecting chemical for pre-constructional anti-termite treatment and chemical barrier underand around the coloumn pits wall trenches basement excavation top surfaces if plinth filling junction of wall and floor, along the external per meter of binding expansion joints surrounding of pipes and conduit etc, complete . |
| 76 | R.C.R Stone Masonery work in foundation in1:6 cement :sand mortar |
| 77 | M 150 brick work in 1:6 cement and fine sand of 1.25 F.M. mortar in foundation and plinth including supply of all materials, labours and T&P etc. required for proper completion of the work .(Edging) |
| 78 | Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size Plenth bend |
| 79 | Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size Lintel Band |
| 80 | Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size R.C.C Work in Slab |
| 81 | Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size R.C.C work in beam |
| 82 | Reinforced cement concrete work in beams suspended floors, roofs having slope up to15 landings balconies shelves chajjaa lintels bands plain windows sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering and reinforcemnet with 1:1.5:2(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size R.C.C work in Collumn |
| 83 | M 150 brick work in 1:6 cement and Coarse sand ofmortor in s/s in one brick thick wall including supply of all materials , labours and T&P etc. required for proper completion of the work. |
| 84 | 115 mm brick work in 1:4 cement and Coarse sand ofmortor in s/s in one brick thick wall including supply of all materials , labours and T&P etc. required for proper completion of the work. |
| 85 | Providing and laying damp proof course 2.5 cm thick with cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 10 mm ) and curing complete |
| 86 | 15 mm cement plaster on roung side of single or half brick wall finished with a floating coat of neat cement of mix.1:4 (1 cement :4 fine sand) |
| 87 | Providing & applying a coatof residual petoleum bitumen of grade of vg-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a plece of cloth lightly soaked in kerosene oil. |
| 88 | Mild steel or iron in plain work such as reinforced concrete wrought to required same as necessary including bending for proper completion of the work. |
| 89 | 15mm cement plaster on plinth of mix:1 cement:4 coarse sand |
| 90 | 15mm thick plasterin 1:6cement mortar over brick work minimum thickness not to be less than 3/6”(12mm) thick including supply of all materials labour and T&P etc. required for proper completion of the work for proper completion of the work but with cement and approved coarse sand in 1:6 cement & fine sand of 1.25 F.M. mortar.in external |
| 91 | 12mm thick plasterin 1:6cement mortar over brick work minimum thickness not to be less than 3/6”(12mm) thick including supply of all materials labour and T&P etc. required for proper completion of the work for proper completion of the work but with cement and approved coarse sand in 1:6 cement & fine sand of 1.25 F.M. mortar.inwall. |
| 92 | Cement concrete flooring 1:2:4 ( 1cement :2 coare sand : 4 graded stone aggregate) finished with a floting coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. Complete. (40 mm thick floor |
| 93 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete |
| 94 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting thejoints with white cement and matching pigments etc., complete |
| 95 | Provinding and laying caremic glazed floor tiles of the 300x300 mm (thickness to be specified by the manufacture) of 1st quality conforming to IS: 15622 of approved make in colour such as white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4(1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching plehment etc |
| 96 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of stepsand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 97 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (a) single leaf- (35mm thick) |
| 98 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (b) Double leaf- (35mm thick) |
| 99 | Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage includingcost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Providing & fixing of doors / windows grill |
| 100 | Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage includingcost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Z- Section Steel windows |
| 101 | Mild steel or iron work of small sizes and section such as holding down bolts, hold fast tie rods, gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage includingcost of bolts, nuts if required for and welding grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing, Angle iron door Chaukhats |
| 102 | Distempering ( two coat) with oil bound distemper of approved beand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer or approved brand & manufacture such as berger, j&N, Shalimar, asian paints after thoroughly brushing the suface from mortar droppongs & other foreign matters & also including preparing the surface material & sand papered smooth including cost of all material |
| 103 | Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 104 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 105 | Providing and laying \"brick coba\" 120 mm thick laid with M-150 class brick bat coba 7.50cm thick with gap of 15mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with acrelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand finised smooth & top mashed false square 30 cm x 30 cm and side wall parapet shall be mono tythic plaster wall up to 30 cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonany Coba with top finised plaster mixed with acetic water proofing compound @ 2% by weight & including s/o all material, labour, T& P etc complete for proper completion of work. |
| 106 | Painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3, Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping including. |
| 107 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete. With 4.0 mm thick glass panes |
| 108 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) |
| 109 | Making grooves 12 to 12mm widex 8mm deep in plaster of the wallor in celling vertically or horizontally as required. |
| 110 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 111 | Centering & shuttering including strutting, propping etc.and removal of form for all heights: Suspended floors, roofs, landings, balconies and access platform. |
| 112 | Centering & shuttering including strutting, propping etc.and removal of form for all heights: Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 113 | Centering & shuttering including strutting, propping etc.and removal of form for all heights: Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 114 | Door Fitting |
| 115 | Providing and fixing I.S.I. mark oxidised M.S. tower bolt finish (Barrel type) with necessary screw etc complete (150 x 100 mm) |
| 116 | Providing and fixing I.S.I. mark oxidised M.S. Sliding door bolt with nut and screw etc complete (250 x 16 mm) |
| 117 | Providing and fixing I.S.I. mark oxidised M.S. Handles conforming to with nut and screw etc complete (100 mm) |
| 118 | Aluminium Sliding Door |
| 119 | Appron Work |
| 120 | Earth work in exacavation in trenches for foundations land for pipes cables etc. in ordinary soil (loan clay or sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand disposal of surplusexcavated earth as directed by the Engineer i/c with in a lead of 50m. |
| 121 | Providing and laying in cement concrete 1:4:8(1 cement :4coarse sand :8 graded stoneaggregate 40 mm nominal size) and curing complete, including cost of form-work, in foundation and floors. |
| 122 | Class 150 Brick Work in1:4 cement and coarsesandof2.20fineness modulus mortar infoundation and plinth including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. |
| 123 | 12MM Th. Cement plaster 1:3 (cement & C.sand) with Neat Cement Finish |
| 124 | Sanitary & Water Supply |
| 125 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. |
| 126 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required : |
| 127 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern,includingpainting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap. |
| 128 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 129 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 130 | Providing and fixingP.V. C. Pipe 6kg.Pis including all Material, Labour T.&P. Complete of work. 110 mm dia. |
| 131 | Providing and fixingP.V. C. Bendincluding all Material, Labour T.&P. Complete of work. For 110 mm dia. |
| 132 | Providing and fixingP.V. C. N Trapeincluding all Material, Labour T.&P. Complete of work. 100*100mm. |
| 133 | Providing and fixingof P.V.C. Copler For 110 mm dia. |
| 134 | Providing and fixingof P.V.C. Tee For 110 mm dia. |
| 135 | Providing and fixingof P.V.C. Door Bend For 110 mm dia. |
| 136 | Providing and fixingof P.V.C. Clamp For 110 mm dia. |
| 137 | Providing and fixingof P.V.C. Covel 90mm. Ddia |
| 138 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 15 mm dia. nominal bore |
| 139 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 20 mm dia. nominal bore |
| 140 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 25 mm dia. nominal bore |
| 141 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore |
| 142 | Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore |
| 143 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)20 mm nominal bore |
| 144 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)25 mm nominal bore |
| 145 | Cutting holes upto 30x30 cm in walls including making good the same : With F.P.S. bricks. |
| 146 | Providing and fixing C.P. brass long body /shortbody bib cock of approved quality conforming to ISstandards andweighing not less than 690 gms. 15 mm nominal bore |
| 147 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 as Such Hindwair 15 mm nominal bore |
| 148 | Providing and fixing of C.P. towel rod 24\"heavy. |
| 149 | Handicap kit |
| 150 | Sanitary and Water Supply (External) |
| 151 | Providing & Laying of 160mm. Dia P.V.C. pipe 6kgcm Sewer Lineincluding excavation of Tranch Providing 1:4:8 cement Concrete P.C.C. Base & Pipe covered with P.C.C. 1:2:4 including all Labour, T.&P. complete of work |
| 152 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 60x60 cm and 75 cm deep |
| 153 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc32mm.dia |
| 154 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 155 | Construction of Septick tank50 USER Size as per ISI Standered 5.00x1.60x1.40 |
| 156 | Earth work in excavation in foundation/tank |
| 157 | Base concrete in 1:4:8 cement:sand:stone ballast |
| 158 | Brick work in 1:4 cement:sand mortar in septick |
| 159 | Brick work in 115mm wall in 1:4 cement : sand mortar |
| 160 | R.c.c. work in 1:1.5:3 cement:sand:stonegrit in Slab and beam |
| 161 | Providing cutting beding MS bar Reinforcement in slab |
| 162 | 20mm plaster in 1:3 cement:sand mortar with neat cement finish |
| 163 | P.c.c. in 1:2:4 cement:sand :stone grit in base to making slope |
| 164 | Providding and fixing C.I. man hole chembar 600x600mm size in slab |
| 165 | Providing and fixing C.I. vent pipe 100mm dia |
| 166 | Providing and fixing c.i. cowel guard 100mm dia |
| 167 | Providind and fixing 150mm dia inlet and out let pipe |
| 168 | SUBMERSIBLE PUMP |
| 169 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart bore log, including hire & running charges of all equipments, toois, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. 300 mm dia |
| 170 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia |
| 171 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia |
| 172 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
| 173 | Development of tube well in accordance with IS: 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit) with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, ic disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 174 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 100 mm dia |
| 175 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp. |
| 176 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubeweli as per IS:2800 (part 1). 100 mm dia. |
| 177 | Supply of submersible pump of make KSB 1.0 HP with control panel, support wire etc. complete. |
| 178 | Providing 2 core PVC insulated submersible cable from pump panel to submersible pump |
| 179 | Providing and foxing GI pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore |
| 180 | Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) |
| 181 | Rain Water Harvesting |
| 182 | Earth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earthas directed by the Engineer i.c. within a lead of 30 m. up tp 1.50mtr. |
| 183 | Providig and laying cement concrete 1:4:8 (1cement:4fine sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors. |
| 184 | R.C.C. works with cement approved coarse sand and 20mm gauge approved stone grit in the proportion 1:2:4 (1cement:6aggregate) in lintels of doors and windows excluding supply of reinforcement and its bending& binding. but including its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labours, tools and plants etc required for proper completion of the works. Binding wire cost being included in the item |
| 185 | Centring & Shutring Slab |
| 186 | Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. |
| 187 | 15mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc. |
| 188 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. |
| 189 | Providing M.S. foot rests including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 gradedstone aggregate 20 mm nominal size) as per standard design : |
| 190 | Providing & Fixing of Posititon Precast RCC Manhole cover and frame of Required shape and approved quailty |
| 191 | Excavating trenches of required width for pipes, cables, etc includingexcavation for sockets, and dressing of sides, ramming of bottoms, depthupto 1.5 m, including getting out the excavated soil, and then returningthe soil as required, in layers not exceeding 20 cm in depth, includingconsolidating each deposited layer by ramming, watering, etc. anddisposing of surplus excavated soil as directed, within a lead of 50 m :Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm |
| 192 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipeswith collars jointed with stiff mixture of cement mortar in the proportionof 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe |
| 193 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thickwith cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement completeas per standard design : Inside size 60x60 cm and 45 cm deep including C.I.Size 90x80 cmcover with frame (light duty) 455x610 mm internaldimensions, total weight of cover and frame to be notless than 38 kg (weight of cover 23 kg and weight offrame 15 kg) : |
| 194 | Supplying and stacking at site.90 mm to 45 mm size stone aggregate |
| 195 | Stone screening 11.2 mm nominal size (Type B) |
| 196 | Red Bajri |
| 197 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.300mm. dia |
| 198 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 100mm. dia |
| 199 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.100mm. dia |
| 200 | Providing and packing of coarse sand around the pipe |
| 201 | Internal Electrification work (Wiring Point) |
| 202 | Wiring for light point/fan point /exhaust fan point /call bell/Sodium point with 1.50 Sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium classPVC conduit,with modular switch, modular plate, suitable G I box and earthing the point with 1.50 sq. mm FRLS PVC insulated copper conductor single core etc. as required. Group C |
| 203 | Wiring for Circuit/Submain wiring along with earth wire with the Following size FRLS PVC insulated copper conductor single core cable in surface / recessed medium classPVC conduit as required. 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire |
| 204 | Wiring for Circuit/Submain wiring along with earth wire with the Following size FRLS PVC insulated copper conductor single core cable in surface / recessed medium classPVC conduit as required. 2 x 4 sq. mm + 1 x 4 sq. mm earth wire |
| 205 | Wiring for Circuit/Submain wiring along with earth wire with the Following size FRLS PVC insulated copper conductor single core cable in surface / recessed medium classPVC conduit as required. 2 x 6 sq. mm + 1 x 6 sq. mm earth wire |
| 206 | Wiring for Circuit/Submain wiring along with earth wire with the Following size FRLS PVC insulated copper conductor single core cable in surface / recessed medium classPVC conduit as required. 4 x 10 sq. mm + 2 x 6 sq. mm earth wire |
| 207 | Supplying and Drawing following sizes ofFRLS PVC insulated copper conductor single core cable in the existing surface / recessed medium classPVC conduit as required. 3 x 1.5 Sq.mm |
| 208 | Supplying and Drawing following sizes ofFRLS PVC insulated copper conductor single core cable in the existing surface / recessed medium classPVC conduit as required. 3 x 4 Sq.m |
| 209 | Supplying and fixing suitable size G I box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 210 | Supplying and fixing of following modular switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required. modular base and cover plate for modular switches in recess etc. as required. 5 / 6 A Switch |
| 211 | Supplying and fixing of following modular switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required. modular base and cover plate for modular switches in recess etc. as required. 3 pin 5 / 6 A socket outlet |
| 212 | Supplying and fixing 5 A to 32 A rating, 250 / 415 V, 10 Ka, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. required.Single pole |
| 213 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. required.40 Amp. |
| 214 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface / recess, complete with tinned copper bes bar, neutral bus bar, earth bar, din bar,interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, double door |
| 215 | Supply and fixing of Following way , surafce / recess,Vertical type ,415 v TPN MCB distribution board of sheet steel , dust protected duly powder painted , including of 200 a tinned copper bus bar , comman neutal link , earth bar , din bar for mounting MCBsetc. as required 6 way(4+12) Double door |
| 216 | Supply and fixing of Following way , surafce / recess,Vertical type ,415 v TPN MCB distribution board of sheet steel , dust protected duly powder painted , including of 200 a tinned copper bus bar , comman neutal link , earth bar , din bar for mounting MCBsetc. as required 63 amp FP isolator |
| 217 | Installation, testing and commissioning of ceiling fan, including wiring of the down rods of standard length (upto 30 cm) with 1.50 sq. mm, FRLS PVC insulated, copper conductor, single core cableincluding providing and fixing phenolic laminated sheet cover on the fan box etc.. as required. |
| 218 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc.. as required. Upto 450 mm sweep. |
| 219 | Supplying and fixing suitable size G I box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 220 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junctiorpox/ wooden block including connections etc. as required. Each |
| 221 | Supplying and fixing brass batten/ angle holder including connectionetc. as required |
| 222 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but modular plate etc. as required. |
| 223 | Supply & Laying of Aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitablesize or as directed by the Engineer-Incharge, complete in all respect. Including excavation and refiling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 25 sq.mm x 3½ core. |
| 224 | Supply and fixing of recess / surface mounting round 15 to 18 Watt cut out min 150 mm, Height Min 40 mm, LED Down lighter having with heat sink, diffuser die cast aluminium housing with heat sink, diffuser/Reflector and driver set, suitable for 24 Hr. Continuous Operation, complete in all respect. CAT: AAA, 1980 - 2200 system lumens, 110 lm/W, PF>0.95, THD<10%, at full load, CRI>80, with 5 year warranty. |
| 225 | Supply & fixing of2\" x 2\" , 36 Watt to 46 Watt, indoor recess / surface mounting LED Square fitting for Armstrong ceiling having Powder coated CRCAhousing bodydiffuser of special polycorbonate meterial and driver set,complete in all respects.CAT: AAA, 3960 - 5060, 70 mm height with fully covered diffuser type, system lumens, 110 lm/W, PF>0.95, THD<10%, at full load, CRI>80, with 5 year warranty. |
| 226 | Supply and fixing of LED Tube Light with Metal heavy duty box type batten Light fitting 1 x 22 watt suitable for upto 1 x 22 watt LED Polycarbonate tube light complete including tube suitable for both surface & suspended complete in all respect. 2420 system lumens, 110 Lm/watt, PF > 0.95, THD<10%, at full load CRI>80, Tube with aluminium sink hit with 3 year warrantee Cat AA |
| 227 | Supply and fixing of water tight oblong 10 watt LED bulkhead luminaire having die cost housing with driver set confirming to IP 65 and above protection. complete in all respect. 1100 system lumens, 110 Lm/watt, PF > 0.95, THD<10%, at full load CRI>80, with 3 year warrantee Cat AA |
| 228 | Supply and fixing of LED Street light fitting having die cast aluminium body and diffuser with driver set suitable for 60 to 72 watt. Confirming to IP 66 and above Protection complete in all respect. 7200-8640 system lumens, High power LED with lenses, 120 Lm/watt, PF> 0.95, THD<10%, at full load, CRI>70, > 440 V & >300 V autocut & restarts feature with 5 year warrantee Cat AAA |
| 229 | S/F of 50 Amp. to 63 Amp. SPMCB (10 KA) Cat-B |
| 230 | S/F of surface/Flush mounting 4 ways V TPN distribution board with additional door without DPX3 160 MCCB complete in all respect, as directed at site by Engineer in charge. Cat.-B |
| 231 | S/F of 80 Amp. To 100 Amp. 4 pole MCCB (16 KA) Thermal Magnetic release. Cat-B |
| 232 | Supply & Laying of 25 mm x 3 mm G.I. Strip from earth electrode directly in the ground as required complete in all respect. |
| 233 | Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000 mm, Outer Dia 50 mm, inner Dia 25, terminal Dia 12 mm, outer G.I. pipe of 16 swg and inner G.I. pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25 mm x 3mm G.I. strip upto switch board (from apron to switch board, the cost of G.I. strip will be extra) along with 30 cm square C.I. frame with hinged cover & masonry housing. |
| 234 | Supply and fixing of 16 gauge M S drum with louvers duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respects . |
| 235 | Supply and fixing of crimping, solderless, copper tin electroplated lugs of Dowells/Ismail make suitable for 1.5 sq.mm to 25 sq.mm cables, including tapping with insulating tape, complete in all respect. |
| 236 | S&F of Fire extinguisher, ABC Type 6.00 Kg. capacity (ISI marked IS: 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 237 | S&F of Co2 type Fire extinguisher, 4.5 Kg. capacity (ISI marked IS: 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 238 | Supply and fixing of fire bucket, round bottom made of G.I. sheet 9-11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-Charge. |
| 239 | S&L of 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality. |
| 240 | S&F of shock treatment chart (Prescribed under I.E Rule) duly framed with glass and supported from back with hard board or soft board with supply of all material labour T&P for proper completion of work. |
| 241 | 63 amp TPMCB CAT-B |
| 242 | Supply and fixing ofhexagonal / round G P fan box of approved make made up 1.0 mm thick ISI Marked G.P. sheet spot welded four to Eight holes of 25.40 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.50 mm G P sheet made upper & lower cover duly screwed fitted with 300 mm round zink cotedM.S. barx 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roofbefore concreting along with supply of all material, labour, T&P etc. required for proper completion of work. |
| 243 | Supply and fixing of 100 Amp. Four pole Change over switch on 50 mm x 50 mm x 6 mm angle iron frame , including the cost of labour, T&P, painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in charge. |
| 244 | Supply & Fixing of Fan Sheet of Backelite |
| 245 | S/F of LED Bulb 9 watt ISI |
| 246 | Supply & Fixing oflight duties exhaust fan 12”dia ISI double ball bearing metalic Usha / Crompton/Bajaj make |
| 247 | Supply & Fixing ofexhaust fan luvers 12”dia |
| 248 | S/f of ceiling fan 1200 mm sweep. Single star rated Usha / Crompton/Bajaj mak |
| 249 | S/F of Kit-Kat fuse 200 Amp with neutrail link ,wooden ply board ,Hole fasner with connection |
| 250 | S/F Required Lugs, Gland ect. |
| 251 | Fire Hydrant System ( Down commer ) |
| 252 | Supply & fixing of welding Heavy Quality Class \"B\", MS pipe conforming to IS:1239 (part-1) for pipes up to 150 mm dia and IS: 3589-1991 for pipes above 150 mm including cutting, threading, welding, clamping fitting with elbow, socket nipple, clamping with MS angle iron supports and fasteners etc. also painting with red oxide and PO red enamel paint with required wrapping Coating complete in all respects.100 mm |
| 253 | Supply & fixing of welding Heavy Quality Class \"B\", MS pipe conforming to IS:1239 (part-1) for pipes up to 150 mm dia and IS: 3589-1991 for pipes above 150 mm including cutting, threading, welding, clamping fitting with elbow, socket nipple, clamping with MS angle iron supports and fasteners etc. also painting with red oxide and PO red enamel paint with required wrapping Coating complete in all respects.80 mm |
| 254 | Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m |
| 255 | Supplying and fixing single headed internal hydrant valve With instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia With cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal /Stainless Steel cap and chain as requiredSingle headed Stainless steel |
| 256 | Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required. Stainless Steel (Grade 304) |
| 257 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:Stainless Steel (Grade 304) |
| 258 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304 sheet with 3 mm dia holes with stainless steel flange 100 mm dia |
| 259 | Supplying (Grade and 304) fixing With orifice plate Of made required out size of 6 to mm be fitted thick tO stainless between reduce flange & landing valve of external and internal hydrants pressure at the outlet to the level of 3.5 kg/cm2 complete as required |
| 260 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way - 100 mm dia M.S. Pipe |
| 261 | Providing, installation, testing and commissioning of non-returr valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required 100 mm |
| 262 | Supplying, fixing, testing and commissioning mmiecinning of of butterfly butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to 1S 13095 of following 100 mm |
| 263 | S/F of Air Vessel made of 250 mm dia, 8 mm thick MS Sheet, 1200 mm in Height With air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories,pressure gauge and painting with synthetic enamel paint of approved shade as required. |
| 264 | Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS: 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for pperation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-\"F insulation, conforming to l$-325 (D) M.S. fabricated common base plate, coupling, coupling guard foundation bolts etc. as required (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head |
| 265 | Supplying and fixing of Pressure Switch inM S pipe line including connection etc. as required. |
| 266 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1010 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.16 sq mm x 4 core |
| 267 | SITC of Fire Hose cabinet box made out of 18 gauge MS sheet including two coats of post office red paint over one coat of primer with 4 mm, thick glass door in front painted \"FIRE\" in red luminous paint. The size of the boxshould be 750 mm X 600 mm X 250 mm size capable of accommodating a pair of hose with coupling and nozzle. The box should be floor mounted type with railway coach lock arrangement and lever for opening the door after breaking the glass complete. |
| 268 | Supply, Installation, Testing & Commissioning of Pressure Gauge. |
| 269 | SITC of Factory fabricated wired metal clad dust and vir,min proof floor mounting main electric control panel for terrace pumpwith starter switches selectors voltmeter etc. |
| 270 | Supply and making sheet for terrace pump |
| 271 | Fire Alarm System |
| 272 | Supplying, installation, testing & commissioning of manual call boxes of M.S. Construction in surface/ recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. |
| 273 | Supplying, installation, testing & commissioning of Fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. |
| 274 | Supplying, inatallation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuite fault, fire condition and all other standard facilities as per IS: 2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.6 Zone |
| 275 | Wiring for light / power plug with 2 x 1.50 sq. mmFRLS PVC insulated copper conductor single core cable in surface / recessed medium classPVC conduit, along with 1 No. 1.50 sq. mm FRLS PVC insulated copper conductor single core for loop earthing as required. |
| 276 | S/F of 7 AH 12 Volt Battery. |
AI Tender Summary
Tender Timeline
Sep 26, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedOct 09, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 09, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender