Tender For Construction Of Swimming Pool In Anupuram Township.; 1 PART - A : CIVIL WORKSEarthwork in open/ Surface Excavation not exceeding 300mm in depth but exceeding 1.5m in width as well as 10 sqm on plan in all types of soil, mixture of gravel and disintegrated rock, hard stiff clay including grading and levelling neatly by breaking clods, disposal of excavated earth upto 50m lead & lift upto 1.5m, (Disposed soil to be levelled by breaking clods, if any and neatly dressed) etc., all complete as per specifications. 2 Earthwork excavation by mechanical means (Hydraulic excavator)/manual means for foundations, trenches, etc., not exceeding 1.5m in width or 10 sqm on plan in hard gravelly soil and other types of soil including bailing of water, if necessary, dressing of sides, levelling and ramming the bottom of trenches, refilling the sides of foundation as required with selected excavated earth and depositing/disposing the surplus earth (Disposed soil to be levelled by breaking clods, if any and neatly dressed) with lift upto 1.5m and within a lead of 50 metres, etc., all complete as per specifications and as directed. 3 All kinds of soil upto 1.50mtr depth 4 All kinds of soil exceeding 1.50 mtr depth but not exceeding 3.00 mtr depth 5 Ordinary/ soft rock upto 1.50 mtr. Depth 6 Ordinary/ soft rock exceeding 1.50 mtr. depth but not exceeding 3.0 mtr. depth 7 Earthwork in open Excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) in all types of soil, mixture of gravel, disintegrated rock, hard stiff clay, soft rock, hard rock including bailing of water, if necessary, dressing of sides, shoring, benching, levelling and ramming the bottom surfaces, with lift as given below and disposal of excavated earth within a lead of 50 metres, etc., all complete as per specifications and as directed by the Engineer-in-Charge. 8 All kinds of soil - Upto 1.5 mtr depth from AGL 9 Excavating trenches of required width by mechanical means (Hydraulic excavator)/ manual means for pipes, cables etc., for depth upto 1.5m in all kinds of soil including excavation for sockets, dressing of sides, ramming of bottoms, getting out the excavated soil and then refilling the soil as required in layers not exceeding 200mm in depth,consolidating each deposited layer by ramming, watering etc., and disposing of surplus excavated soil as directed within a lead of 50m, (Disposed soil to be levelled by breaking clods, if any and neatly dressed) etc., all complete as per specification. 10 Earthwork excavation for trial pits of required size in hard gravelly soil and other types of soil upto 1.50 mtr. depth without damaging the existing underground service lines including shoring, strutting, bailing of water, protection of existing underground utilities such as water line, service cables, etc., refilling the sides of trial pit as required with selected excavated earth and depositing / disposing the surplus earth (Disposed soil to be levelled by breaking clods, if any and neatly dressed) with a lead of 50 metres and finishing the surface to proper level etc., all complete as per specifications and as directed by Engineer- in-Charge. 11 Filling available selected excavatedearth (excluding rock) in trenches, plinth, sides of foundation etc., in layer not exceeding 200 mm in depth including consolidating each deposited layer by ramming and watering, lead upto 2.0 Km and lift upto 1.5m etc., all complete as per specification. 12 Providing gravel base of approved thickness for flooring, kerbwall, etc., including supplying gravel, spreading gravel in uniform layers, watering, ramming, consolidating, dressing the top surface to the required level, etc., all complete as directed by the Engineer-in-charge. 13 Clearing heavy jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30cm measured at a height of 1m above ground level, removal of rubbish upto a distance of 60m outside the periphery of the area cleared, cutting and stacking the useful fire wood if any within an initial lead of 100 mtrs etc., all complete as per specification and as directed by Engineer-In-Charge. 14 Cutting and felling trees of the girth (measured at a height of 1m above ground level) including cutting of trunks,branches, removing the roots, stacking of serviceable materials and disposal of unserviceable materials within a lead of 200m including filling the pits and depression with excavated earth,etc., all as directed by Engineer-In-Charge. 15 Beyond 300mm girth upto and including 600mm girth. 16 Beyond 600mm girth upto and including 1200mm girth. 17 Trimming of tree branches, which causing hindrance to free vehicle movement, blocking street light and touching the building etc., on road sides, avenues, streets and near buildings, including cutting the branches of trees using necessary tools, collecting, transporting and disposing them at places shown by the department using their own means of conveyance all as directed by the Engineer-in- charge. 18 Beyond 300mm upto and including 600mm Girth Trees 19 Beyond 600mm upto and including 1200mm Girth Trees 20 Providing Pre-Construction Anti-termite Treatment using Chlorpyriphos E.C 20% with 1 % concentration or other approved chemical as detailed below including cost of chemicals, labour and all other incidental charges for entire ground floor area of building and injecting termicide emulsion to the soil in contact with the foundation along the perimeter of both internal and external walls, etc., all as per IS: 6313 (Part-2). 1) Top surface of consolidated earth within plinth walls shall be treated with chemical emulsion @ 5 Ltr/Sq.m of the surface before the sand bed or sub-grade is laid. 2) Treatment along the external perimeter and internal perimeter at junction of the wall and the floor of the building shall be treated with chemical emulsion @ 7.5 Ltr/Sq.m, to facilitate this holes shall be provided @ 150mm apart upto GL for inner side and upto 300mm below GL for external perimeter. 3) The entire treatment shall be done as per the specifications and instructions of the termicide Manufacturer and as directed by the Department. 4) The treatment should be done by an agency specialized in the job having sufficient knowledge of anti termite treatment. 5) Five years guarantee from the date of completion of maintenance period shall be given by the contractor in the prescribed format of the department for the above anti-termite treatment work. 21 Providing and laying in position of plain cement concrete using hard granite broken stone in foundations, trenches etc. including mechanical mixing, ramming, compaction, leveling, curing, dewatering, if any including the cost of formwork etc., all complete as per specifications. 22 1 : 1.5 : 3 (1 cement : 1.5 sand : 3 graded stone aggregate 20mm nominal size) 23 1 : 3 : 6 (1 cement : 3 sand : 6 graded stone aggregate 40mm nominal size) 24 1 : 2 : 4 (1 cement : 2 sand : 4 graded stone aggregate 25mm nominal size) 25 Providing and laying 100mm thick Base course under the flooring with cement concrete 1 : 3 : 6 using 25mm size hard broken stone including consolidation, formwork, curing etc., complete as per specifications. 26 Filling in depression with cement brick aggregate concrete 1:2:4 using 20mm size broken brick aggregate including compacting, curing etc., all complete upto Floor V level 27 Providing, erecting, placing in position and removing Formwork for all insitu concrete works at all lifts and all shapes such as circular works, chamfers, splays, etc., using Steel / Plywood shuttering including centering, scaffolding, strutting, propping with necessary bracing in all areas, fixing of EPs, cutting holes and fixing pipe sleeves, applying of approved form oil over surface in contact with concrete, de-shuttering after specified curing period, etc., all complete as per drawings and specifications.[Note : Measurement for the formwork shall be the area of forms in contact with concrete surfaces. Stop boards for construction joints will not be measured separately for payment. Centering and shuttering where exceeding 3.5m height in one floor shall be measured and paid for separately.] 28 For Plain Surfaces upto 3.5m Lvl 29 For Plain Surfaces above 3.5m Lvl 30 Providing and fixing in position of 50mm thick Thermocole board (Heavy density minimum 18.00 kg / Cum.) wrapped in 200 micron thickness polythene sheets including placing infor machine foundation works, etc., all complete as per specification and as directed by Engineer. 31 Providing and casting insitu Reinforced Cement Concrete of the following grades of design mix by Weigh batching using machine crushed hard broken granite stone of nominal size 20mm including cost of admixtures in recommended proportion wherever required, mechanical mixing, transporting, placing at all lifts, vibrating, consolidation, curing, finishing smooth all exposed faces, for all insitu concreteitems, etc., as per drawings and specifications.Note :1) The rate quoted shall be exclusive of reinforcement and formwork which will be paid for separately under relevant items.2) The rate of concrete shall include the cost of admixture in recommended proportions as per IS 9103 as per direction of Engineer-in-charge.3) Cement proportion for Concrete Mix shall be on the basis of weigh batching only as per design mix.4) The cost towards any upward / downward variation required to obtain the specified strength over the minimum cement content will be paid for or deducted at the rate specified in Schedule F. 32 M 30 Grade Concrete(The Cement content considered is 370 Kg per Cu.m)- Upto FFL 33 M 30 Grade Concrete(The Cement content considered is 370 Kg per cu.m) - above FFL and upto floor V 34 Providing, cutting, bending, placing and binding Steel reinforcement using TMT bars of Fe-500D grade in all reinforced cement concrete works including cutting, bending,fixing, tieing in position with 1.6 mm dia soft drawn annealed binding wire, cost of cover blocks in C.M 1:2, etc., complete as per specifications and drawings. ImportantNote: The required quantity of steel reinforcement as mentioned in the schedule should be procured by the contractor only of SAIL, Rashtriya Ispat Nigam Limited (VIZAG), TATA Steel & JINDAL from authorised dealers which shall conform to IS: 1786 (Latest Edition). 35 Providing, hoisting and fixing in position of 50mm thickness of precast slabs in cement concrete 1:1.5:3 using hard broken stones of maximum size 20mm finished smooth of various sizes and patterns including necessary formwork and moulds, mechanical mixing, finishing the exposed surface, curing, fixing at all levels, grouting with CM / Cement grout wherever required, etc., all complete excluding cost of reinforcement which will be measured separately under relevant item as per specifications and as direction of the Engineer-in-charge. 36 Providing, hoisting and fixing in position 50mm thick Precast RCC jali at all lifts of approved pattern and size as per drawing with cement concrete 1 : 1.5:3 including required nominal reinforcement, curing, smooth finished surface with float coat of neat cement on all sides, fixing and jointing with CM 1:3, scaffolding etc., all complete as per drawing and specification. 37 Providing, hoisting and fixing in position of Exhaust fan Hoods as per drawings and specifications using cement concrete 1:1.5:3 using hard broken stones of maximum size 20mm finished smooth of various sizes and patterns, including necessary formwork and moulds, mechanical mixing, finishing the exposed surface, curing, fixing at all levels, grouting with CM / Cement grout wherever required, etc., all completeexcluding cost of reinforcement which will be measured separately under relevant item but including formwork complete. 38 Providing and fixing 5mm thick Polypropylene plastic lattice system of approved design, colour and size at all elevations including fixing withAnodized aluminium frame work or other approved frame work, sealing the joints with required sealants, etc., all as per drawing and specification and as directed by Engineer In Charge. (Note: Rate for frame work with Aluminium will be paid for separately under relevant item) 39 Providing and laying Random Rubble masonry in Cement mortar 1 : 6 (1 cement: 6 coarse sand) in foundation and plinth using hard granite stones obtained from approved quarry includingbond stones of 2 Nos/Sq.m at 1.5 to 1.8 mtrs apart, raking out joints, curing, etc., all as per standard specification. 40 Providing and constructing brick masonry at all lifts in cement mortar 1:5 using well cured flyash bricks of class 5 (non-modular) made up of using Flyash + Sand + Lime + additives (Gypsum/Cement) with waterproofing chemicals and accelerators confirming to IS-12894 or latest edition including suitable scaffolding, raking out joints, continues curing for specified period, etc., all complete as per specifications and drawings. 41 Upto FFL 42 Above FFL 43 Providing and constructing 110mm thick brick workfor partition walls at al liftsin cement mortar 1:4 using well cured flyash bricks of class 5 (non-modular) made up of using Flyash + Sand + Lime + additives (Gypsum/Cement) with waterproofing chemicals and accelerators confirming to IS-12894 or latest edition includingsupplying and providing 2 Nos. of 6/8mm MS rod at every third layer, suitable scaffolding, raking out joints, continues curing for specified period, etc., all complete as per specifications and drawings. 44 Supplying and fixing 20mm (±2mm) thick both side polished Kota Stone slabs for Shelves in Cupboard/Wardrobe/Shoe rack, etc., including fixing by cutting a chase of appropriate width with cutter and embedding the stone into the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) finished smooth, front face polishing, rounding the edges, etc., all complete as per specifications and as directed by Engineer-in-charge.(Note : Kota stones shall be got approved by the Engineer before making bulk order.) 45 Supplying, fabricating and fixing Steel Grills of required pattern and size for Windows/Ventilators, Staircase Hand Rails, etc., fixed to openings/wooden frames at site, comprising of MS square bars / MS rounds / MS flats, etc., including fixing with necessary wood screws for fixing grills / by welding in steel windows, painting with two coats of anti corrosive paint of approved colour and make over a coat of red oxide zinc chromate primer/ zinc phosphate primer, etc., all completed as per specification.[Note: The rate shall be inclusive of lifting arrangements if any required to hoist and concrete embedments for fixing the steel works.] 46 Supplying, fabricating and fixing Steel work welded in built up sections and framed work at all lifts comprising Chequered plates, MS angles, other structural steel sections, etc., of TATA or SAIL or approved equivalent make including cutting, welding, bending to shape, painting exposed faces with two coats of anti-corrosive paint of approved colour over a coat of red oxide zinc chromate primer / zinc phosphate primer, embedding with Cement concrete, if necessary, etc., all complete as per specifications and drawings.[Note: The rate shall be inclusive of lifting arrangements if any required to hoist and concrete embedments for fixing the steel works. ] 47 In gratings, frames, guard bar, ladders, railings, brackets, gates and similar works 48 Supplying, fabricating and fixing of EPs, Structural Steel work and pipe sleeves etc., at all lifts comprising MS angles, MS plates, tees flats, rounds, squares, other structural steel sections, pipe sleeves and pipes of various sizes, IS channels, IS beams, square rods, etc., of TATA or SAIL or approved equivalent make including cutting, welding, bending to shape, painting exposed faces with two coats of anti-corrosive paint of approved colour over a coat of red oxide zinc chromate primer / zinc phosphate primer, embedding with Cement concrete, etc. complete all as per specifications and drawings.Note: The rate shall be inclusive of lifting arrangements if any required to hoist and concrete embedments for fixing the steel works. 49 Providing and fixing of Fly proof Stainless Steel (Grade 304) wire gauze of 0.4mm dia wire and 1.4mm aperture on both sides of approved quality and make over Partly panelled Door / Grill door including fixing with second class Teak wood beading or Aluminium frame work, cost of screws, nails, rawl plug, etc., all complete as per specification. [Note: Cost of frame work i.e., Steel or wood or aluminium, will be paid for separately under relevant item] 50 Supplying and fixing of factory made Solid WPC door frame having density of 850 - 950 Kg/Cum, water absorption less than 1% ofapproved make with suitable rebate for shutters including the joints shall be mitered & Jointed with self driven self tapping screws of size 75 mm x 4 mm and made by SP 5 epoxy seal and fevikwik / solvent, fixing the frame to wall with suitable dia & length anchor fastener, etc., all complete as per manufacturer specifications and as directed by the Engineer-in-Charge. 51 Supplying and fixing in position single leaf/double leaves of following thick non decorative type factory made Wood Polymer Composite (WPC) solid door shutters of approved make having density of 600 - 800 Kg/Cum, water absorption less than 1% and tensile strength greater than 12 MPa including providing aluminium lipping / Teak wood all-round if required, fixing the lipping with suitable adhesive, fixing required hardware fittings, fixing door using required screws, etc., all complete as per specifications and as directed by Engineer-In-Charge.[Note: Cost of Door frame, hardware fittings and Aluminium / Teak wood lipping will be paid for separately under relevant item.] 52 35mm thick WPC door 53 Providing and fixing in position of 12mm thick Cement bonded pre-laminated particle board of `Bison Lams or approved equivalent make panels prelaminated with decorative lamination on both sides for door shutters, partitions, cupboard shutters, sliding shutters, etc., including cutting to required shape and size, making as per drawing with Anodized aluminium frame alround with lock rails at the centre for each leaf, fixing in structural opening, providing teakwood lipping alround for sliding shutters, etc., all as per specification and as directed by the Engineer-In-Charge. (Note:-Aluminium frame work will be paid for separately under relevant item.) 54 Providing and fixing Sliding glass door Notice board of approved size of make Schoolneeds or Corporate Concepts or Alkosign made up of anodized aluminium frame work along with 5mm thick clear float glass of SAINT GOBAIN or MODI GUARD or ASAHI of approved make for sliding door including providing sliding arrangement, star locks, 12mm thick soft board covered with colour (blue / maroon) blazer / flannel cloth backed with PVC sheet, providing clamps at the back side for wall mounting, etc., all complete as directed by Engineer-in-charge. 55 Supplying, fitting, fixing in position of 5mm thickness Tinted glass of approved colour of Saint Gobain or approved equivalent make for doors, partition, windows, fixed glazing, louvers, etc., including fixing withputty,TW beading, Neoprene gasket, etc., all complete as per drawing and specifications. 56 Supplying, fabricating and fixing of 40mm thick pressed Steel Flush Door of make STEELTECH or SIGNUM or TATA PRAVESH or NCL Seccolor or other approved equivalent make having outer door frame of size 105x60mm (Single Rebate) and steel flush door as detailed below including fabricating the frame, door shutter, providing thermal barrier between sheet, filling the hollow portion of the door with honeycomb/Solid Polyurethene foam, providing vision panel of size 200x300mm with 5mm thick clear toughned glass of approved pattern, fixing the door with required hardware fitting of make Dorma or other approved make, fixing the door assembly with necessary holdfast / anchor fasteners as per site condition, filling the hollow of door frame and hold fast pocket with CC 1:2:4 using 12mm downgraded stone aggregate which will be paid for separately under relevant item., etc., all complete as per drawing, manufacturer specifications and as directed by the Engineer-in-Charge. Door Frame: - Outer door frame of size 105x60mm (Single Rebate) made from 1.2mm thick Galvanized steel sheet with Zinc coating not less than 120gm/Sqm and shall be finished with PU paint of approved colour over zinc rich epoxy primer. Provision for providing fixed glass of 300mm height at top over the door shutter shall be made as per drawing.Door Shutter :- Pressed Steel fully Flush double skin door shutter of thickness 40mm (+5mm) fabricated 0.8mm thick Galvanized steel sheet with Zinc coating not less than 120gm/Sqm with approved colour finish. Top and Lower skin joined by roll formed snap fitting groove on the style. Providing thermal barrier between sheet and filling the hollow portion of the door with solid Polyurethene foam of density not less than 40kg/m3. Providing vision panel of size 200x300mm with 5mm thick clear toughned glass of approved pattern as per drawing. The shutter shall be finished with PU paint of approved colour over zinc rich epoxy primer. 57 Hardware fittings: -Fixing the door with required hardware fitting such as 4 Nos of 100x75x3mm SS ball bearing hinges for each shutter, Mortice Lock with handle and key, SS pull ‘D’ handle of 32x600mm length for each shutter, Door stopper, PVC solid buffer, Door Co-ordinator/ Selector for double leaf door fixed over frame, concealed tower bolts for double leaf shutters, 1 No. of 150mm and 1 No. of 3000mm barrel type premium SS tower bolt. All hardware fittings shall be of make ‘Dorma’ or other approved equivalent make over the wooden inserts placed inside the shutter. Single leaf door of size upto 1000mm width and 2100mm height 58 Double leaf door of size upto 1800mm width and 2500mm height 59 Providing and fixing in position Aluminium partitions, doors, windows, ventilators, louvers,fixed glazing, sliding windows north light glazing, sliding shutter E Channel, trellis, etc., using heavy duty standard anodized aluminium extruded sections, anodized aluminium sheets as per relevant IS code of JINDAL or approved equivalent make including pivots, approved door and window handles, door stopper, EPDM gasket, neoprene gasket lining, stainless steel screw, mastic filling, weather strips, washers, reinforcing the door shutters at top and bottom with MS rod threaded and fixed to vertical members, etc., as required and as per drawing etc., all complete at all heights and as directed by the Engineer in charge.Note:-1. Payment shall be made on the basis of weight of aluminium members/section fabricated and actually installed in position without extra allowance for wastage no extra payment shall be made for non-aluminium consumable items like screws, gasket, weather strips PVC/Neoprene lining, sliding wheels for windows, in built tower bolt, reinforcing rods, etc.,2. Glazing, particle boards, Aluminium grills, mesh etc., will be paid separately under relevant items.3. All fittings except under Note-1 will be paid separately under relevant item and the fittings shall be of matching colour anodized aluminium sections. 4. The aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required cleat angles at no extra cost.5. The aluminium section shall be anodized with MATT FINISH (15 micron thick) finishing and of approved shade/colour with the approval of Engineer-In-Charge. 60 Supplying, fabricating bending and fixing the position of AISI 304 grade stainless steel section for hand railing/hanger rodsmade of Hollow tubes, channels, plates, etc., of required size including butt / mitre welding,grinding, buffing, polishing, making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete,fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement, drilling holes in floor/walls embedding/ grouting with suitable grouting materials, etc., all complete as per drawing and specification and as directed by Engineer-In-Charge.Note:- 1. The stainless steel tubular pipe/ section shall conform to ASTM A554/A312.2. All welding joint shall conform to V groove joint and joint shall be ground finish.3. There shall not be any spatter or imperfection on the pipe and the pipe surface shall be ground and smooth.4. External surface of SS pipe shall be buffed to mirror finish. 5. The rate shall be inclusive of providing ball joiners, flush joiners, base plate/flanges, cover plate, end caps epoxy glue, round face/square face glass connecters for fixing etched colour glass if any of required size with gaskets including curved railings where ever required cost of screws, weld etc.,6. The entire pattern of stainless steel hand railing work/pattern including fixing of etched glass, if any in the hand rail shall be got approval by Engineer in charge/Architect before execution.7. Only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc., for payment purpose. 61 Providing and fixing swimming pool starting block of size 500 mm × 500 mm x 400mm of approved make conforming to FINA standards made up of heavy quality stainless steel grade 304 base using hollow tubes, channels, plates, etc., of required size with FRP top in blue colour or other approved colour including butt / mitre welding,grinding, buffing, polishing, making curvature (wherever required),fixing the starting block using suitable anchoring arrangement, finishing, etc., all complete as directed by the Engineer-in-Charge. 62 Supplying and fixing of factory made Solid PVC foam door frame of approvedmakewith suitable rebate for shutters (Profile FP-6030) including the joints shall be mitered & Jointed with self driven self tapping screws of size 38 mm x 4 mm and made by SP 5 epoxy seal and fevikwik / solvent, fixing the frame to wall with suitable dia & length anchor fastener, etc., all complete as per manufacturer specifications and as directed by the Engineer-in-Charge. 63 Supplying and fixing in position single leaf Factory made flush door shutterof 25 mm thick PVC integral foam sheet of make M/s. Jain Irrigation Systems Ltd. (Ex-cel sheet) or other equivalent approved make of white colour for flush door shutter including providing recessions for hinges, fixing with following fittings over the granite/PVC door frame using required fasteners, finishing all edges with mixture of PVC powder & solvent for smooth finish, etc., all complete as per specification and as directed by the Engineer-In-Charge. 64 The door shutter shall be fixed with the following hardware fittings: -a)4 Nos. of 75 mm long stainless steel butt hinges ofGARGbrand bearing ISI mark with suitable stainless steel screws.b) Two numbers of 125mm long anodized aluminium Dhandle of make Classic/Crown or approved equivalent as per IS - 208 bearing ISI mark with suitable CP screws.c) Two numbers of 75mm long anodized aluminium baby latch type/SS cranked type tower bolt with suitable CP screws.d) One number of 50mm long solid PVC door buffer with 75mm long CP screws. Note: - 1) All furniture fittings shall be of approved quality and make. 2) The rate quoted shall be inclusive of fixing of door shutters with required hardware fittings as detailed above. 3)The PVC Integral Foam shall be factory manufactured solid section of light weight sheet with fine & homogeneous closed cell structure with smooth, glossy, hard surface finish on both sides. The sheet shall have density of 500 - 600 Kg/Cum, water absorption less than 1% and tensile strength greater than 11 MPa.4) The entire door shall be jointless shutter.5) The sizes shall be approximately 700 mm x 2100mm, however exact dimensions shall be measured at site before manufacturing and payment will be paid for finished size of door shutter. 65 Providing and fixing IS : 12817 marked stainless steel butt hinges (Heavy weight) of make GARG or approved equivalent make including fixing with suitable stainless steel screws, etc., complete. 66 125 x 65 x 2.50mm 67 Providing and fixing ofAluminium butt hinges of size 100 x 63 x 4mm conforming to IS : 205 of make Classic or Crown or approved equivalent make including anodized transparent or dyed to required colour or shade, fixing with necessary CP screws, etc., all complete as per specification. 68 Providing and fixing IS:208 marked Aluminium handles of size 125mm x 12mm dia. of make Classic or Crown or approved equivalent make including anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade, fixing with necessary SS screws etc., all complete as per specification. 69 Providing and fixing ISI marked Aluminium sliding door bolts (Aldrops) of Classic or Crown or Global or approved equivalent make as per IS 2681 including anodized transparent or dyed to required colour or shade, fixing with 5 Nos of clip and staple with necessary CP screws etc., all complete as per specification. 70 250 x 16 mm 71 Providing and fixing IS:204 marked Aluminium tower bolts ofmake Classic or Crown or approved equivalent make including anodized transparent or dyed to required colour or shade, fixing with necessary CP screws, etc., all complete as per specification. 72 250 x 12mm 73 Providing and fixing anodized Aluminium hook and eye of 250mm long with suitable screws. 74 Providing and fixing 300mm long plate fixed with three / four prong type anodized aluminium robe hooks of approved make with suitable screws. 75 Providing and fixing Anodized aluminium hanging type door twin rubber stoppers of required colour or shade including fixing with necessary screws etc., all complete as per specifications. 76 Providing and fixing 50mm long and 40mm dia. PVC solid door buffer with 75mm x 10mm SS screws and cup washers. 77 Providing and fixing Stainless steel Roller wheels of approved quality and make foraluminium sliding door shutters including fixing as directed by Engineer-In-Charge 78 Providing and fixing in position universal Hydraulic door closer bearing ISI mark of EVERITE/GODREJ or approved equivalent make as per IS:3564 (Type-B No.2) including fixing as per specifications. 79 Providing and fixing double action hydraulic floor spring of HARDWYN or GODREJ or approved equivalent make with ISI mark, pivoting and all other arrangements including cost of cutting floor, SS cover plates with brass pivots & other necessary accessories required for the work to facilitate smooth operation of the door shutter etc., all complete as directed by the Engineer-in-charge. 80 Providing and fixing in position of built in Mortice lock with pair of Key of GODREJ or approved make for aluminium doors including cutting the frame and fixing with necessary screw etc., complete all as directed by Engineer-In-Charge. 81 Providing and fixing Sliding window latch for sliding windows of make EBCO or other approved make including fixing with necessary screws as directed by the Engineer-in-charge. 82 Supplying, providing and placing in position of 225mm wide and 8-11mm thick flat ribbed type PVC water stop of approved make, the surface of water stoppers shall be ribbed, the outer edges shall be at the level of central bulb and free from blisters, pinholes, cracks and embedded foreign matters as per latest IS specifications includingcutting, placing in position with supports, lapping etc., all complete as per specifications and as directed by Engineer at site. (Note: - The Lapping shall be pasted with suitable adhesives and starched at lap ends as directed by Engineer and no extra payment shall be made for overlapping.) 83 Providing and laying Indian Patent Stone (IPS) flooring 20 mm thick with cement concrete of mix 1:2:4 (1 part cement : 2 parts coarse sand : 4 parts graded stone aggregate), using 20 mm and 10 mm size hard broken stone aggregates, finished with a floating coat of neat cement, including laying in panels, applying cement slurry, compacting, curing, rubbing the surface smooth, and finishing with a power trowel machine etc., all complete as per specifications and as directed by Engineer - in - charge. 84 Providing and fixing glass strips in joints of terrazzo / IPS flooring using 40/20mm wide & 4mm thick glass strips including grinding the top surface smooth to match with the floor, etc., complete as per specifications. 85 Providing and fixing 14-16mm thick White Agaria Marble Stone slab table rubbed, exposed edges rounded and polished of required size and fixed in urinal partitions, shelves above wash basin, etc., by cutting a chase of appropriate width with chase cutter and embedding the stone into the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) finished smooth, front face polishing, rounding the edges, etc., all complete as per specification and as directed by Engineer-in-charge. 86 Providing and fixing in position of Terracotta Jhali of size 200X200X75mm of make Eurocon or other approved make, pattern and quality at all lifts including scaffolding, fixing & pointing in CM 1:3, curing etc., all complete 87 Providing and fixing Granite stone in Flooring with 16-18mm thick one side Leather finished granite stone slab of approved shade, colour, size and texture laid over 20mm (average) thick base in cement mortar 1 : 4 (1 cement : 4 coarse sand) including laying, chamfering, providing grooves where ever required, pointing the joints with approved grouting materials, curing, cleaning, polishing, etc., all completed as per drawings and specification.Note: The Granite stones shall be got approved by the Engineer before making bulk order. The rates for steps shall be inclusive of providing three Nos. of 4mm grooves @ 25mm interval on all the treads from the nosing edge. 88 Ruby red/Pitch black for Flooring 89 Ruby red/Pitch black for Steps riser and treads using single piece of length upto 2mtr. 90 Providing and fixing Granite stone in Flooring with 16-18mm thick one side mirror polished granite stone slab of approved shade, colour, size and texture laid over 20mm (average) thick base in cement mortar 1 : 4 (1 cement : 4 coarse sand) including laying, chamfering, providing grooves where ever required, pointing the joints with approved grouting materials, curing, cleaning, polishing, etc., all completed as per drawings and specification.Note: The Granite stones shall be got approved by the Engineer before making bulk order. The rates for steps shall be inclusive of providing three Nos. of 4mm grooves @ 25mm interval on all the treads from the nosing edge. 91 Ruby red/Pitch black for Steps riser and treads using single piece of length upto 2mtr. 92 Providing and fixing Marble / Granite work gang saw cut mirror polished, (pre moulded and prepolished slab) machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laidover 20mm thick base cement mortar 1 : 4 (1 cement : 4 coarse sand) with joints treated with white cement mixed with matching pigment, epoxy touch ups, etc., including rubbing, curing, finishing, providing holes of required diameter, providing opening to fix counter basins, providing grooves wherever required, etc., all complete at all levels as per specifications.(Note: The marble/Granite stones slab shall be got approved by the Engineer before making bulk order.) 93 Granite - Ruby red/Jet Black (16 - 18mm thick) 94 Providing and laying Kota stone slab in Flooring with 20-25mm thick Kota stone of required size of approved shade and texturelaid over 20mm (Average) thick base of cement mortar 1 : 4 (1 cement : 4 sand) and joints treated with grey cement slurry mixed with colour pigments to match the shade of the slab including curing, rubbing and polishing in three levels to obtain mirror polish, waxing to give smooth finish, etc., all complete at all levels as per specifications. 95 Providing Half Round Edge Mouldingto 16-18mm thick marble / Granite or 20mm thick Kota stone counters, vanities, sills, etc. including machine polishing theedges to give high gloss finish etc., all complete as per specifications and as directed by Engineer - in – charge. 96 Granite work 97 Providing and laying jointless 10 mm thick heavy-duty vitrified anti-slip tiles, specially designed with foot braille, of approved colour with water absorptions conforming to IS: 15622 (BIb) suitable for swimming pool deck areas as well as outdoor applications of make Johnson (Maxgrip, R11) or other approved equivalent makeincluding setting over a base layer of 20 mm thick cement mortar 1:4, jointing with grey cement slurry @ 3.3 kg per sqm or with Cerabond/other approved adhesive, grouting the joints with epoxy-based joint filling material or other equivalent approved material, curing, cleaning the surface with acid wash, etc., all complete as per specification and as directed by the Engineer-in-Charge.(Note:- The sample shall be got approved by the Engineer-in-charge before making bulk order). 98 Providing and laying of vitrified pool tiles of size 247 x 122mm (or) 240 x 115mm and 8mm thickness in swimming pool/ diving pool area with water absorptions conforming to IS: 15622 (BIb) andFINA (Federation International De Nation) Standard of approved make, including supply of approved color, texture and shade of vitrified tiles floor and wall surface preparation, leveling, fixed over prepared surface using high-performance tile adhesive suitable for submerged applications with 3- 5mm spacer, filling/ scaling of joints between the tiles with epoxy grout of Bal Endura Epoxy grout /Letecrete / Kerakoll with matching colour pigment to make it water tight and finished neat complete, cleaning the surface with acid wash, etc., all complete as per specification and as directed by Engineer in charge.Note:- 1) The sample tile shall be got approved by the Architect/Engineer before procurement. 99 Vitrified plain mosaicpool tiles of blue/black/white colour etc., 100 Designer mosaic tiles of approved pattern and design (Neo pool ocean/Neo pool art blue/Pearl Textura blue etc., 101 Pool accessories (Internal cove, Internal angles) etc., 102 Vitrified anti-slip pool tiles of size 244 x 119 mm 103 Vitrified anti-slip pool step tiles with safety marking of size 244 x 119 mm 104 Providing and laying 1st quality Rectified (Jointless) Ceramic floor tiles (Glazed or Anti-skid) of size 300 x 300 mm or more confirming to IS : 15622 of KAJARIA (Approved concept of Digital Series) or SOMANY (Digital Series - Glasstra) or JOHNSON (Approved concept of Satin & Rustic / Glossy series)or other approved make in all colours, shades in Floors laid over 20 mm thick cement mortar 1 : 4 (1 Cement : 4 Coarse sand)jointing with grey cement slurry @ 3.3 kg per sqm or by using Cement based high polymer modified quick set tile adhesive (water based) or other approved tile adhesive including grouting the joints with white cement and matching pigments etc., all complete as per specification. 105 Providing and fixing 1st quality Rectified (Jointless) Glazed ceramicwall tiles of approved concept series confirming to IS 15622 of KAJARIA/ SOMANY / JOHNSON or other approved make in all colours, shades of following sizes in Skirting, Risers of steps and Dados laid over 12 mm thick bed of cement mortar 1 : 3 (1 Cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm or by using Cement based high polymer modified quick set tile adhesive (water based) or other approved tile adhesive including providing Motiff tiles, pointing in white cement mixed with pigment of matching shade, curing, etc., all complete as per specifications and as directed by Engineer-in-Charge. 106 Wall tiles of 300x600 mm or more [KAJARIA (Digital Series) or JOHNSON (Satin &Rustic / Glossy series)] 107 Supplying and fixing of Rigid PVC nosing of approved quality and colour at the corners of Ceramic tiles dadooing including finishing all complete as directed and as per specifications. 108 Providing and laying Cementitious water proofing treatment system comprising of bond coat, top screed concrete including preparation of surface by chipping/dismantling the existing loose surfaces/ roof tiles with bed mortar, cleaning the surface by washing throughout, filling the cracks using approved crack fillers, injection/ grouting the cracks where ever required with cement slurry using suitable water proofing admixtures, applying bond coat, finishing the top with 20mm thick IPS flooring with water proofing admixtures, leak test, curing, etc., all completeas perspecifications and as directed by the Engineer-in-Charge.Note:-i) This treatment should be done by an agency specialized in the job having sufficient knowledge of waterproofing treatment, authorized trained applicator should be used and certificate should be submitted before commence the work. ii)This work shall be executed at inaccessible terrace at a height of upto 11m. Aluminium mobile tower scaffolding having double width platform with stairway as directed by EIC shall be provided by the contractor to access the working area during execution of work.iii)Five years guarantee from the date of completion of maintenance period shall be given by the contractor in the prescribed format of the department for the workmanship and the materials provided. 109 Plastering the ceiling / exposed surfaces of concrete with CM 1:3; 6mm thick to make the surface uniform, free from undulations and imperfections including hacking pock marking of surfaces with pointed tool, scaffolding, curing at all lifts etc., all complete as per specifications and as directed by Engineer-incharge. [Note: 6mm premium glass fibre of make Dugar & Co or Recron shall be mixed with Cement @ 60 gms of glass fibre per 50kgs of cement] 110 Plastering with Cement Mortar 1:5, 12mm thick for brickwork / Concrete on internal faces at all lifts including scaffolding, curing and forming grooves wherever necessary all complete as per specifications and as directed by the Engineer-incharge. [Note: 6mm premium glass fibre of make Dugar & Co or Recron shall be mixed with Cement @ 60 gms of glass fibre per 50kgs of cement] 111 Plastering with Cement Mortar 1:5, 12mm thick for brickwork / Concrete on its external faces at all lifts includingadding admixtures of approved make, scaffolding, curing and forming grooves wherever necessary all complete as per specifications and as directed by the Engineer-incharge. [Note: 6mm premium glass fibre of make Dugar & Co or Recron shall be mixed with Cement @ 60 gms of glass fibre per 50kgs of cement] 112 Plastering the ceiling / exposed surfaces of concrete with CM 1:3; 12mm thick to make the surface uniform with float coat of neat cement, free from undulations and imperfections including adding admixtures of approved make,hacking pock marking of surfaces with pointed tool, scaffolding, curing at all lifts etc., all complete as per specifications and as directed by Engineer-incharge. [Note: 6mm premium glass fibre of make Dugar & Co or Recron shall be mixed with Cement @ 60 gms of glass fibre per 50kgs of cement] 113 Plastering with cement mortar 1:3; 20mm thick including supplying and mixing of water proofing compound of approved make at the rate of 2% (Two percent) by weight of cement or as specified by manufacturer including finishing smooth with a floating coat of neat cement, scaffolding, curing, etc., all complete at all lifts as per specification.[Note: 6mm premium glass fibre of make Dugar & Co or Recron shall be mixed with Cement @ 60 gms of glass fibre per 50kgs of cement] 114 Providing Raised Cement Mortar bands with plain cement mortar 1:3 for elevational purpose over parapet, sunshade, RCC drop, etc., at all levels including hacking pock marking of concrete surfaces with pointed tool, scaffolding, curing and forming grooves wherever necessary, etc., all complete as per drawing & specifications and as directed by Engineer-In-Charge.(Note : Rate shall be quoted for 1 mtr long and 1 cm wide band.Length will be measured in running metres, width of the band will be measured in CM and the quantity shall be calculated in metre-cm units) 115 12mm thick Raised Cement Mortar bands 50mm wide 116 12mm thick Raised Cement Mortar bands 100mm wide 117 Supplying and fixing in position of Alkali resistance Glass fibre mesh (4-5mm square aperture with 145 gsm) over the joints of RCC and Brick work with cement paste before plastering as directed by Engineer-in-charge. 118 Providing water proofing treatment in water retaining portion of swimming pool etc,. with two coat of two component highly flexible polymer modified cementitious water proofing coating of make FAB chemical (Mixguard AC) or Bostik (Boscolastic) or equivalent including preparation of surface free from dust/oil/grease, sealing the CPVC/PVC/DI sleeve pipes using non shrink grout mortar over bonding coat using SBR chemicals and sealing the joints with polyester fleece along the periphery of UPVC pipes, applying two coat of water proofing etc,. all complete as detailed below as per manufacturer specification and as directed by Engineer-in-charge.Surface preparation: The surface to receive water proof treatment shall be cleaned to make sure that the surface free from dust, dirt, laitance, debris, loose mortars, oil particles etc., which may negatively affect the adhesion of water proof treatment with mother concrete surface. Sealing bore hole gap around the sleeve pipes: The gap around the pipe shall be filled with non shrink grout mortar of make FAB chemicals (Mixgrout NS) or equivalent and providing necessary slurry tight form work to enveloping the pipe with a bead of 6 to 8mm and 5mm above the surface level along with a sealer coat of make FAB chemical (Mixprime AC100) or equivalent and seal with saturated polyester fleece all along the periphery of pipes. 119 Water proof treatment: Providing and applying two coats of two component Highly elastomeric flexible polymer modified cementitious cold applied water proof coating of make FAB chemical (Mixguard AC) or Bostik (Boscolastic)over the prepared surface to cover complete area, finishing etc. Extend the coating up to a minimum of 300mm height to the adjoining wall as per manufacturer specification.Note:- 1) The swimming pool alround RCC wall structure shall be tested for the water leaking before and after treatment by filling with water for 24hours and grouting shall be carried out if any leakage found.2) The treatment should be done by an agency specialized in the job having sufficient knowledge of waterproofing treatment. 3) Five years guarantee from the date of completion of maintenance period shall be given by the contractor in the prescribed format of the department for the workmanship and the materials provided. 120 Painting all internal faces of walls / ceiling plastered surfaces with two coats ofAcrylic Emulsion paint of make Asian (Tractor) / Berger (Bison)or other approved equivalent make of approved shade over a coat of interior wall primer of make Asian (Professional) / Berger (BP Primer) or other approved equivalent make including preparation of surfaces, applying the primer coat, scaffolding,etc., all complete at all lifts as per specifications. 121 Painting all internal faces of walls / plastered surfaces with two coats ofAcrylic Emulsion paint of make Asian (Tractor) / Berger (Bison)or other approved equivalent make of approved shade over a coat of interior wall primer of make Asian (Professional) / Berger (BP Primer) or other approved equivalent make including preparation of surfaces,applying approved makewall care putty as per manufacturer specification, sanding the surface, making surface smooth without porous, applying the primer coat, scaffolding,etc., all complete at all lifts as per specifications. 122 Providing Painting over all exposed surfaces at all heights over rough cast plaster/plain plaster with Two Coats of premium exterior emulsion paint ofmake Asian (APEX - Dust proof exterior emulsion) / Berger (Anti dustt weather coat)or other approved equivalent make of approved shade over a coat of exterior wall primer of make Asian / Berger or other approved equivalent make including preparation of surfaces, curing, scaffolding etc., all complete as per specifications. 123 Painting over Plain Plaster at all lifts. 124 Painting External wall with Textured paint of approved pattern/ finish in three coats (One coat of Texture and two coats of External paint) over a coat of external primer of approved colour and texture of makeBerger (Walmasta) or Asian (Apex Duracast) or approved equivalent make at external surface at all levels and height including preparing the base surface, sand the surface with sand paper, wash and scrub with coir/wire brush, attending to broken edges /corners or patches of plastered surface with cement grout, scaffolding, staging, painting one coat of Weather coat External primer of make Berger or other approved make, application of illusion texture using Berger- Walmasta exterior texture or other approved make, making approved patterns/designs using trowel/ roller, providing vertical/horizontal grooves if any required, painting the top surface with two coats of overcoat using weather coat exterior emulsion of make Berger (Weather coat smooth) or other approved make, cleaning the surface etc., all complete as per manufacturers specification and as directed by Engineer-in-charge. 125 Providing and fixing in position of white glazed vitreous china ware ORISSAPAN water closet of size 580x440mm of PARRYWARE/ HINDWARE or approved equivalent make with S or P trap with all jointing materials including making holes in masonry, fixing the Orissapan, joining the pipe and trap with Lip Ring of PRINCE of approved make, reconstructing the same, encasing the pan and trap with brick jelly concrete 1:2:4 and back filling extra space with river sand/brick jelly concrete,all as per specifications and as directed by the Engineer-in-Charge. 126 Providing and fixing high level/Low level polymer DUAL flushing cistern of 3/6 litres capacity of make PARRYWARE/ HINDWARE model SLIMLINE or approved equivalent conforming to IS: 7231 including fixing cistern at required height and level with necessary TW wall plugs, screws, connecting inlet and outlet, connecting the cistern and closet with suitable dia. PVC pipes and fittings conforming to IS:4985 etc., complete as per standard specifications. 127 Providing and fixing in position of white glazed vitreous chinaware European type water closet comprising of:i) White glazed vitreous chinaware European Water Closet of Parryware (Niagara) or approved equivalent make including fixing with necessary plugs, screws and packing the joints with cement mortar 1:1, joining the pipe and trap with WC pan connector of Ashirvad or approved equivalent make etc., all complete as per specifications and as directed.ii)White Solid Anti-microbial seat cover of Parryware or approved equivalent make including fixing.iii) High level/Low level polymer Dualflushing cistern of 3/6 litres capacity of make PARRYWARE model SLIMLINE or approved equivalent make conforming to IS: 7231 including fixing cistern, connecting the cistern and closet with Flush bends, PVC pipe, WC pan connector of Ashirvad or approved equivalent make, cup bush washer, etc.,Note:(i) Tenderer shall note that the cost quoted shall be inclusive of all materials like EWC, Seat Cover, Flushing Cistern, flush bends, etc., (ii) All the above items for quality colour and make shall be got approved before making bulk order. 128 Providing and fixing in position best vitreous China Wash Basin comprising of:i) White glazed vitreous chinaware wash basin 580 x 450mm Inoya / 550x405mm Nubra Plus of Parryware or approved equivalent make fixed with Multi purpose rag bolt or painted CI bracketsii)32mm heavy quality PTMT waste coupling of Prayag or approved equivalent make, washer, check nuts.iii) 15mm heavy quality C.P. Brass Pillar Cock of make Jaquar (Continental Series) / Prayag (Neptune series) with ISI mark or approved equivalent make.iv)32mm PTMT Bottle trap (Prayag or equivalent make) Note:(i) Tenderer shall note that the cost quoted shall be inclusive of all materials like wash basin, waste coupling, pillar cock, Bottle trap, nails, screws and plugs which are necessary for fixing including cost of labour.(ii)Quality, colour and make for all the above items shall be got approved before making bulk order. 129 Providing and fixing in position of vitreous Chinaware urinal comprising of :i) Urinals of Parryware (New Magnum) or equivalent make with suitable CI brackets/MS clamps.ii) 32mm CP brass urinal domed waste coupling of Jaquar/ Parryware make or equivalent make.iii) Heavy quality 15mm brass spreaders of Parryware make or equivalent make and suitable copper tubes complete as directed.iv) 32mm PTMTBottle trap of Prayag or approved make v) 15mm CP Brass Urinal push angle cock of make Parryware (Lapin-N)Note:(i) Tenderer shall note that the cost quoted shall be inclusive of all materials like urinal basin, waste coupling, spreader, bottle trap, push angle cock, nails, screws and plugs which are necessary for fixing including cost of labour.(ii) All the above items for quality, colour and make shall be got approved before making bulk order. 130 Providing and fixing 5mm thick mirrors of SAINT GOBAIN or approved equivalent make of approved size backed with 4mm thick AC sheet or marine plywood including 30x20mm aluminium frame works, painting with two coats of enamel paint over one coat of primer for backing sheet, fixing in frame work with gasket, fixing firmly against brick wall with suitable clamps, etc., all complete as per specification and as directed by Engineer-in-charge. 131 Providing and fixing heavy quality 600mm CP Towel rail ofapprovedmake with wall flange including suitable CP screws all complete as per specifications and as directed by Engineer-in-charge. 132 Providing and fixing heavy quality Brass GRAB bar 450mm long ofapproved make with wall flange including suitable screws all complete as per specifications and as directed. 133 Providing and fixing heavy quality 15mm C.P. Brass Long body screw down Bib Cock with wall flange of`JAQUAR [Continental Series] or approved equivalent make including fixing with suitable SS valve/cup, flange etc., all complete as per specification. 134 Providing and fixing heavy quality 15mm C.P. Brass BIB COCKwith wall flange of `JAQUAR [Continental Series] or approved equivalent make including fixing with suitable SS valve/cup, flange etc., all complete as per specification. 135 Providing and fixing heavy quality 15mm CP brass Angle Stop Cock with wall flange of JAQUAR [Continental Series] or approved equivalent make including fixing with suitable SS valve/cup, flange etc., all complete as per specification. 136 Providing and fixing heavy quality 15mm CP brasstwo way bib cock with wall flange of `JAQUAR [Continental Series] or approved equivalent make and shape including fixing with suitable SS valve/cup, flange etc., all complete as per specification. 137 Providing and fixing heavy quality 15mm C.P. Brass screw down Concealed type stop cock extra heavy body with adjustable wall flange of `JAQUAR [Continental Series] or approved equivalent make including fixing theconcealed body, exposed parts with suitable flange etc., all complete as per specification and as directed by Engineer-In-Charge. 138 Providing and fixing heavy quality Chromium Plated 100mm dia overhead Shower (Single Flow ABS Body Chrome Plated with Gray Face Plate) along with 190mm long shower arm with wall flange of JAQUAR / PARRYWAREor approved equivalent make including fixing with suitable SS valve/cup, flange etc., all complete as per specification. 139 Supplying and fixing Health Faucet (hand shower - ABS Chrome plated) with 1m long flexible tube with wall hook ofapproved make including fixing the wall hooks, finishing the surface, etc., all complete as per specification and as directed. 140 Providing and fixing 15mm dia. and 450mm long PVC inlet connection with PVC check nuts and washers at both endssuitable for Cold and Hot Water Connection confirming to IS specification of PRAYAG /PARRYWARE or approved equivalent make with ISI mark including fixing etc., all complete as directed by Engineer. 141 Providing and fixing PTMT liquid soap container or approved equivalent make including fixing and making good the surface after fixing as per specifications. 142 Supplying, laying and fixing in position the following sizes of ductile iron pipes in standard length of K-9 class conforming to IS:8329/2000, suitable for rubber gasket (SPR) push on joints, pipes shall be bearing with ISI marks and cement mortar lining inside barrel including lowering them into the excavated trenches and laying, fixing in position to proper grade and alignment all as per IS:12288 and standard specifications including cutting the pipes to the required length, cost of labour, pipes and other materials, tools and plants for laying and installing the pipe lines and testing the lines to the required hydrostatic pressure of 14 kgs./sq.cm. at the specified intervals but excluding cost of Ductile iron specials / fittings and joints which will be paid under relevant items.(Note: The effective length of the DI fittings / specials, valves, double flanged pipes, etc., will be deducted from the overall measurement of the pipe line for making payment against this item). 143 100mm dia. K-9 classDI pipes 144 200mm dia. K-9 classDI pipes 145 Providing and fixing rubber gasket (SBR or EPDM) push on joints to the following sizes of DI pipes including insertion of rubber gasket into the centering rings of the socket of the pipes and pushing the spigot end into socket and making the joint intact to withstand the hydrostatic pressure of 14Kgs./sq.cm. including cost of all materials, rubber gasket, tools and plants, etc., complete conforming to IS:5382/1985 and IS:12288/1987. 146 100mm dia. NBDI pipes 147 200mm dia. NBDI pipes 148 Supplying and fixing tested heavy quality DI specials / fittings K-12 class socket, spigot and flanged specials such as bends, collars tapers, tees, duckfoot bend, flanged socket and flanged spigot tail pieces, blank flanges, etc. and conforming toIS:9523/2000 and IS:8329/2000 drilling holes to the flanged fittings shall be PN classification and socket specials /fittings shall be suitable for rubber gasket (SPR) push on joints, etc., complete (Joints will be paid for separately under relevant items). 149 Upto 300mm dia. 150 Labour charges only for cutting the existing main DI/CI pipe line of following diameter with steel saw and making provision for new connection by introducing the DI/CI specials including making good the leakages, testing at required pressure allcomplete as per specifications and as directed at site. (Note: Cost of CI/DI specials and joints will be paid for separately under relevant item.) 151 100mm dia. pipes 152 200mm dia. pipes 153 Providing and fixing PVC Nahani trap of FINOLEX/PRINCE or approved equivalent make conforming to the relevant IS code, heavy quality of self cleaning design with 75mm internal dia. and outlet 125mm dia. PVC grating with perforated holes on top, including embedding in cement concrete 1:2:4, forming circular holes by providing and fixing 110mm OD uPVC SWR-TYPE B pipes of required height upto floor level, levelling and rendering smooth, making good the floor and wall etc., complete as per specifications. (Rate shall include cost of PVC pipe and it shall not be paid extra). 154 Providing and fixing PVC Multi Floor Trap of FINOLEX/PRINCE or approved equivalent make conforming to the relevant IS code, heavy quality of self cleaning design with 110mm internal dia and outlet 125mm dia. PVC grating with perforated holes on top, including embedding in cement concrete 1:2:4, forming circular holes by providing and fixing 110mm OD PVC pipes of required height upto floor level, levelling and rendering smooth, connecting the outlet and inlets, making good the floor and wall etc., complete as per specifications. (Note: Rate shall be inclusive of cost of PVC pipe and embedding PCC.) 155 Providing and fixing 150mm Square PTMT gratings of Prayag or approved equivalent make over the rain water pipes fixing in CM 1:3 as per specifications. 156 Providing and fixing best quality 110mm OD SWR uPVC pipes - Type A (suitable for ventilation work and rain water applications) conforming to IS: 13592 - latest edition with ISI mark including moulded fittings/specials such as bends, shoes, etc., jointing with seal ring conforming to IS - 5382 leaving 10mm gap for thermal expansion, fixing to the wall with adequate no. of PVC clips for rain water down take pipes etc., all complete as per specifications and as directed by the Engineer in charge. 157 Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes(Class-I) of SDR-11 of approved make conforming to IS 15778 having thermal stability for hot and cold water supply including providing CPVC plain and brass threadedfittings, fixing the pipe with concealed clamps at 1 m spacing, jointing of pipes and fittings with 1 step CPVC solvent cement, cost of cutting chasses and making good the same, testing of joints complete, etc., all complete as per specification and as directed by Engineer In-Charge. (Note: Concealed work including cutting chases and making good the wall, etc.,) 158 20mm dia Nominal size 159 25mm dia Nominal size 160 32mm dia Nominal size 161 Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (Class-I) of SDR-11 of approved make conforming to IS 15778 having thermal stability for hot and cold water supply including providing all CPVC plain and brass threadedfittings, fixing the clamps at 1m spacing, jointing of pipes and fittings with 1 step CPVC solvent cement, testing of joints, etc., all complete as per specification and as directed by Engineer In-Charge. (Internal work-Exposed on wall) 162 25mm dia Nominal size 163 32mm dia Nominal size 164 40mm dia Nominal size 165 50mm dia Nominal size 166 Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of Sch-40 (ASTM F441) of approved makehaving thermal stability for hot and cold water supply for External work including providing all CPVC plain and brass threadedfittings, fixing the clamps at 1m spacing, jointing of pipes and fittings with 1 step CPVC solvent cement, testing of joints, etc., all complete as per specification and as directed by Engineer In-Charge. (Internal work-Exposed on wall) 167 80mm dia. Nominal size 168 100mm dia. Nominal size 169 150mm dia. Nominal size 170 Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (Class-I) of SDR-11 of approved make conforming to IS 15778 having thermal stability for hot and cold water supplyfor External work including providing all CPVC plain and brass threadedfittings, jointing of pipes and fittings with 1 step CPVC solvent cement, testing of joints, trenching and refilling, etc., all complete as per specification and as directed by Engineer In-Charge. Note : Cost of Earth work excavation will be paid for separately under relevant item. 171 25mm dia. Nominal size 172 50mm dia. Nominal size 173 Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of Sch-40 (ASTM F441) of approved make having thermal stability for hot and cold water supply for External work including providing all CPVC plain and brass threadedfittings, jointing of pipes and fittings with 1 step CPVC solvent cement, testing of joints, trenching and refilling, etc., all complete as per specification and as directed by Engineer In-Charge. Note : Cost of Earth work excavation will be paid for separately under relevant item. 174 100mm dia. Nominal size 175 150mm dia. Nominal size 176 Supplying and fixing flanged joint suitable for 50mm dia CPVC SDR 11 pipe of approved make including providing CPVC flange adapter (threaded or socket type), fixing the joints with backing ring, rubber gasket and required bolts & nuts, to makeleak-proof connection , all joints shall be properly aligned and tightened, etc., all complete in all respects as per specifications and as directed by the Engineer-in-Charge. 177 Supplying and fixing flange joint suitable for CPVC ASTM D1785 (Schedule 40) pipes and specials of approved make, including providing CPVC flange adapter (threaded or socket type), fixing the joints with backing ring, rubber gasket and required bolts & nuts, to makeleak-proof connection , all joints shall be properly aligned and tightened, etc., all complete in all respects as per specifications and as directed by the Engineer-in-Charge. 178 80mm dia flanged set 179 100mm dia flanged set 180 150mm dia flanged set 181 Providing and fixing the following internal dia. Gun metal full way gate valve of Leader or approved equivalent make bearing ISI mark confirming to IS:778 with female ends, screwed bonnet, integral seat, non rising spindle class-I including fixing the valve etc., all complete as directed by the Engineer-in-charge. 182 25mm internal dia. Gate valve 183 32mm internal dia. Gate valve 184 40mm internal dia. Gate valve 185 50mm internal dia. Gate valve 186 Providing and fixing the following internal dia. Double flanged Sluice Valve of Kirloskar/Leader or approved equivalent make bearing ISI mark confirming to IS:14846 for PN 1.6 rating Hydraulic pressure with female ends, screwed bonnet, integral seat, non rising spindle class-I including fixing the valve with bolts, nuts, rubber insertion, etc.,all complete as directed by the Engineer-in-charge. 187 100mm dia Sluice valve 188 200mm dia Sluice valve 189 Providing and fixing the following internal dia. threaded GI pipe sleeve of medium quality not exceeding in length of 500mm welded with 6mm thick MS plate of size 150 x 150mm or 300x300mm with one coat of red oxide primer including fixing in formwork, embedded in water tank side wall, etc., all complete. 190 40mm Nominal Bore 191 50mm Nominal Bore 192 Providing and fixing 50mm internal dia. Brass Ball cock of make Peaco or Prayag as per IS: 1703 bearing ISI mark with heavy quality PVC float and brass rod of heavy full bore type including fixing as directed by Engineer-In-Charge. 193 Supplying, laying and jointing of following dia. of Rigid PVC pipe and specials of approvedmake with ISI mark as per IS 4985:2000 unloading at work site, laying and fixing the pipes and specials withnecessary solvent cement of approved make, testing to required working pressure etc., all complete excluding earthwork excavation which will be paid separately under relevant item as per specification and as directed by the Engineer-in-charge. 194 50mm OD PVC pipe of class-3 (6Kg/Sq.cm) 195 Providing and laying of following dia. of SWR uPVC pipes - Type B (Suitable for soil and waste discharge system having wall thickness of minimum 3.2 to maximum 3.8mm) of approved make conforming to IS - 13592 - Latest edition including the cost of PVC pasting type specials such as door bends, door tees and cowls etc., heavy quality for soil waste or vent or antisyphonage PVC pipe, fixing with PVC pipe clips or laid embedded under floor slab and fixed to walls wherever required, etc., all complete as per specifications. 196 75mm OD uPVC pipes and specials. 197 110mm OD uPVC pipes and specials. 198 160mm OD uPVC pipes and specials. 199 Providing and laying of underground drainage / Sewerage uPVC pipes of SN 8 class (SDR-34) conforming to IS:15328 of approved make suitable for elastomeric sealing ring joints including cost of spigot and socket endpipes with provision for sealing rings, specials, cutting, jointing with elastomeric seals, testing, etc., all complete as per specifications and as directed by Engineer-in-Charge. 200 110mm OD uPVC pipes SN8 Class 201 160mm OD uPVC pipes SN8 Class 202 200mm OD uPVC pipes SN8 Class 203 Providing and constructing GULLY CHAMBER of internal finished size 300 x 300mm including providing, supplying and fixing 150 x 150mm (±10mm) PVC Gully trap with PVC grating at top of approved make including excavation in all types of soils, backfilling, embedding the trap in plain cement concrete 1:4.5:8 using 40mm size granite aggregates and constructing thechamber above the embedded PVC with 110mm thick (plus or minus 5mm) bricks in Cement Mortar 1:5 with well burnt stock bricks, plastering over both internal and external faces of brick work with Cement Mortar 1:3; 12mm thickfinished smooth with a floating coat of neat cement on both faces, providing and fixing 400 x 400 x 25mm precast slab in reinforced cement concrete of 1:2:4 using 12mm and below hard broken granite stones including cost of gully trap, chamber etc., all complete as per specification. 204 Construction of rectangular Manhole/ Inspection Chamber of following size clear internally with brick masonry walls 230mm thick using well burnt chamber bricks in Cement Mortar 1:5 (with necessary corbelling as required), plastering with Cement Mortar 1:3; 12mm thick inside and outside,inside finished smooth with a floating coat of neat cement and outside trowel finished including excavation in all types of soils, back filling, providing and laying bed concrete 150mm thick and having 150mm wide projection on all the sides with Plain Cement Concrete 1:4.5:8 using 40mm maximum size hard granite broken stone, forming, benching and channellingin plain cement concrete 1:2:4 using 20mm maximum size hard broken granite stone, finishing smooth etc., all as per specifications, drawings and as directed at site - to an initial depth upto 1.00 metre.(Note: The rate quoted shall be excluding the cost of cover slab & steel reinforcement which will be paid for separately under relevant item.) 205 600x450mm for initial depth of 1.00 metre. 206 Extra depth of rectangular manhole/ inspection chambers of size 600x450mm over the initial depth of 1.00 metre. 207 900x600mm for initial depth of 1.00 metre. 208 Extra depth of rectangular manhole/ inspection chambers of size 900x600mm over the initial depth of 1.00 metre. 209 Construction of rectangular rain water Chamber of 900 x 600mm size clear internally with brick masonry walls 230mm thick using well burnt chamber bricks in Cement Mortar 1:5 (with necessary corbelling as required), plastering with Cement Mortar 1:3; 12mm thick inside and outside,inside finished smooth with a floating coat of neat cement and outside trowel finished including excavation in all types of soils, back filling, providing and laying bed concrete 150mm thick and having 150mm wide projection on all the sides with Plain Cement Concrete 1:4.5:8 using 40mm maximum size hard granite broken stone, forming, benching and channellingin plain cement concrete 1:2:4 using 20mm maximum size hard broken granite stone, finishing smooth etc., all as per specifications, drawings and as directed at site - to an initial depth upto 1.00 metre.(Note: The rate quoted shall be excluding the cost of cover slab & steel reinforcement which will be paid for separately under relevant item.) 210 Supplying and fixing of Steel steps with zinc coating of size dowel distance 330mm c/c and leg length 225mm with 16mm dia. Core material of steel with zinc coating encapsulated with plastics / PE of 2.5mm thick of make Linktech or other approved make including fixing by drilling holes, applying cement paste with bonding agents, fixing the rungs to required alignment, etc., all complete as per specifications and as directed by Engineer-in-charge. 211 Making connection of drain or sewer line with existing manhole including breaking in to and make good the walls, floors with cement concrete 1:2:4 mix (1cement:2 coarse sand: 4 graded stone aggregate20mm nominal size) cement plastered on both side with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain, etc., complete. 212 For pipes 250 to 300 mm diameter 213 Providing and laying factory-made swimming pool overflow channel gratings of 350 mm width and 25 mm depth with 3-pin interlocking type made up of UV-stabilized 100% virgin polypropylene + co-polymer material of blue or other approved colour and pattern with anti-slip ribed texture conforming to ASTM/DIN standards including laying in the required pattern over drain, jointing the grating with 3 pin interlocking, finishing the surface, etc., all complete as per manufacturer specifications and as directed by Engineer-in-Charge Note: 1)The gratings shall have a minimum load-bearing capacity of 300 kg/m² with anti-slip ribbed textured surface2)The grating shall have high resistance to chlorine, saltwater, and mild acids. 214 Supplying laying and jointing of RCC hume pipes with collars of class NP-2 as per IS specifications including aligning to proper level and line as directed at site, jointing with Cement Mortar 1:2, curing, etc., complete as per specification. 215 100mm dia. RCC hume pipes 216 150mm dia. RCC hume pipes 217 250mm dia. RCC hume pipes 218 300mm dia. RCC hume pipes 219 Providing and laying of Wet Mix Macadam (WMM) for Sub-base and base course conforming to clause 406 of MORT&H Specification for road and bridge works (Fifth Revision) using 53mm downgraded stone aggregate including cost of coarse aggregates, fine aggregate, premixing the Material with water at OMC in mechanical mix plant, carriage of mixed Material by tipper to site, laying in uniform layers with paver/motor grader in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density, etc., all as per specification and as directed by Engineer-in-charge. 220 Providing and laying factory made precast Kerb stone of M-20 grade cement concrete of size 100mm thick & 500mm ± 50mm depth with suitable interlocking arrangement, top chamfering of size 50x70 mm or as approved size including excavation, conveying, laying the precast kerb blocks in position to the required line, level and curvature, making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), jointing / pointing the joints with cement mortar 1:3, refilling the sides, compacting, making drainage opening wherever required, etc., all complete as per specification and as directed. (Note: Length of finished Kerb edging shall be measured for payment and Precast kerb stone shall be approved by Engineer-in-charge.) 221 Painting road side kerb wall with Two coats of Acrylic water based Road marking paint conforming to IS 164 of make Asian paints (Apcotrack IS)or Berger (Guideline RM 164 Paint) or other approved equivalent make comprising of white and black colour strips and including preparation of surfaces, applying with brush in alternate strips, etc., all complete as per manufacturer specification and as directed by Engineer-in-charge. 222 Providing and laying 60mm thick factory made chamfered edgeprefabricated cement concrete interlocking Solid / perforated paver block of M-30 grade made by table vibratory method using PU moulded with strong vibratory compaction of approved size, design, shape, laid in required colour and pattern over 50mm thick compacted bed of coarse sand including cost of sand filling, levelling with required slope, ramming the surface, watering, consolidation using vibratory earth rammers, filling the joints with sand, cleaning, etc., all complete as per specification and as directed by the Engineer-incharge. 223 Providing and laying Dry stone pitching of 230mm thick for revetment using retrieved RR stone including collecting with department source place, cleaning the old mortar from retrieved stone, laying pitching to the required grade and slope, packing and filling the intersects, watering, compaction, Flush / sunk pointing the joints with CM 1:3, etc.,all complete as per specifications and as directed by Engineer-in-charge. (Note:-Required quantity of RR stone will be supplied by department at free of cost). 224 Providing and fixing Granite stone Plaque of approved size using 16-18mm thick gang saw cut mirror polished (pre moulded and prepolished slab) Jet black or other approved shade granite stone engraved with approved font letters, logo, symbol, etc., using machine cut/ flame finishand border/letters with golden finish colour including fixing the plaque over 12mm thick Cement mortar 1 : 3 (1 Cement : 3 Coarse sand) or approved adhesive, pointing with White cement mortar 1 : 2 (1 White cement : 2 Marble dust) with an admixture of pigment to match the granite/marble shade, fixing to be secured to the backing by means of suitable approved cramps if required, finishing the surface, curing, etc.,all complete as per specification and as directed by Engineer-In-Charge. 225 Dismantling Reinforced cement concrete at all lifts including clearing and depositing the same with a distance of 100 metres as directed by Engineer-in-charge. 226 Dismantling RR Masonry in cement mortar at all lifts including stacking of RR stone, clearing and depositing the debris within a distance of 100 metres all as directed by Engineer-in-charge. 227 Dismantling Brick workin cement mortar at all lifts including clearing and depositing the debris within a distance of 100 metres all as directed by Engineer-in-charge. 228 PART - B : ELECTRICALWORKS Supply and Embedment of following sizes of flush mountingPOWDER COATEDTPN/SPN DB Enclosures with Double Doorand per Phase isolation DBs consisting of Phase, Neutral and Earth Bus and interconnecting wires etc. at suitable depth in brick work as per the detailed specification and as directed by the Engineer-in-charge. 229 12 WAY Cat No:DETPI012DD (Vertical) or equivalent make TPN TIER Per Phase Isolation (PPI) DB 230 Supply and Embedment of following sizes Cable end termination box at suitable depth in brick work as per the detailed specification and as directed by the Engineer-in-charge. 231 TPN,12 way Cable end box, Cat No:DETPI012DD or equivalent suitable for TPN, 12 way TPN TIER Per Phase Isolation Distribution Board Cat No:DBTPI012DD (Vertical) 232 Supply and installation of following sizes ofHeavy Duty, Hot Dip Galvanised MS ERW Conduitsfor Electrical & Communication System with all the required accessories like round JBs, Solid Long Bends, Check Nuts, Nipples, Couplings, Reducers, Copper Clips, Copper Conductor, GI Wire etc, on roof slab, column, beams etc as per the detailed specification. 233 25 mm Dia 1.8mm, wall thickness GI Heavy Duty ERW Conduits with 75mm deep junction boxes 234 32 mm Dia 1.8mm, wall thickness GI Heavy Duty ERW Conduits with 75mm deep junction boxes 235 Supply and installation of following sizes of Heavy Duty, Hot Dip Galvanised MS ERW Conduits for Electrical & Communication System with required Solid Long Bends, Check Nuts, Nipples, Couplings, Reducers,Copper Clips, Copper Conductor, GI Wire etc, in Floor, Walls, Brick, Block Masonry, etc. including chasing & replasteringas per the detailed specification. 236 25 mm Dia 1.8mm, wall thickness Heavy Duty ERW Conduits with 50mm deep junction boxes 237 32 mm Dia 1.8mm, wall thickness Heavy Duty ERW Conduits with 50mm deep junction boxes 238 40 mm Dia 2mm, wall thickness Heavy Duty ERW Conduits with 50mm deep junction boxes 239 Supply and Embedment of 50mm Deep, Square/Rectangular Concealed type and GI double earthed modular metal boxes of the following types and as specified in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification. 240 ONE/TWO Module 241 THREE Module 242 FOUR Module 243 SIX Module 244 Supply and Embedment of MS fan Hook Boxes in RCC roof slab with finishing and making good as per drawing No:IGC/ESD/9170/8009 and the detailed specification. 245 Supply and embedment of concealed type Hot dip galvanised MS boxes of the following sizes in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification. 246 150(W)X150(H)X80(D)mm, 1.8mm thick sheet Hot dip galvanised MS box 247 300(W)X300(H)X120(D)mm,1.8mm thick sheet Hot dip galvanised MS box 248 Supply and Installation of MS Brackets, Supports, Frame work, Clamps, Base Channels, etc. fabricated out of angle / Channel / Rods etc. The rate quoted shall include the cost of fabrication / welding, cleaning and painting/ galvanising as follows including supply of required, fasteners, nuts, washers, etc., 249 MS fabrication 1 coat primer & 2 coats synthetic enamel paint 250 Supply and installation of Hume Pipe Direct in ground. 251 Supply and installation of 150 mm Dia. 2 Mtrs Long, NP 2 Class Hume Pipes at a depth of 1200 mm including supply of Collars and fixing them with1:1 cement mortar and curing, including excavation in all types of soil, backfilling complete as directed by Engineer-in-Charge. 252 Supply and installation of following sizes ofHeavy Duty, Hot Dip Galvanised GI pipes with required accessories on Floor, column, beams etc including chasing and replastering as per the detailed specification. 253 80 mm NB, 4.8mm, wall thickness Heavy Duty GI pipe along with solid long GI bends 254 50 mm NB, 4.5mm wall thickness Heavy Duty GI pipe along with solid long GI bends 255 Supplyand installation of Powder coated MS boxes with SS Krone base module (i.e. For mounting of telephone Krone disconnection modules) for the following D.B sizes. 256 500(W)x300(H)x150(D) MS Box. 257 PART - C : MECHANICAL WORKS (PIPE WORKS & ACCESSORIES)Supply, installation, testing and commissioning of Kirloskar make Electrical driven Horizontal, End suction, Top Discharge Back Pull out Design Centrifugal pump with suction and delivery of size 125 x 80 mm with CF6M / SS316 impeller, cast iron casing, SS410 shaft fitted with mechanical seal, single stage capable of delivering75 m³/hr against a total head of 35-45 mtrs coupled by means of Love joy coupling to a 4 pole Squirrel cage type totally enclosed fan cooled (TEFC) motor suitable for operation on 415v, 3phase, 50 +/- 5 hz, S1 duty, 50 deg C ambient temperature, class F insulation, IP-55 with a rating of 15 KW whcih should confirm to IS:325 1978 of make kirlosker / cromptn / siemens etc., complete including coupling guard, anti-vibration rubber pads with Common bed plate of fabricated mild steel channel with suitable bolt and nuts and with RCC pedestal 1:1.5:3 as required for above pump & motor reinforced with 12mm TMT bar with all necessary formwork and plastering as required with suitable J-bolt and nuts and the pedestral holes shall be grouted etc., all as per the specification and as directed by the engineer-in-charge.Note : Contractor shall produce manufactures test certificate for motor and pump and performance datasheet for pump. 258 Supplying and fixing in position Wafer type swing check reflux valve, as per relevant IS standardof following specifications: Suitable for handling clear cold water of Nominal Pressure: - 1.6 MPa.Operating position of the valve: Horizontal. Material of Construction: - Body –CI, Flap: SS, Locking plug: - GM,Locking pin: - H.T. Brass, Hinge pin: Brass, O-Ring: EPDM, Eye bolt: Carbon SteelNote: -1. For each valve enclose the Hydrostatic Body Test and Hydrostatic Seat test. 259 150 mm dia 260 100 mm dia 261 Supplying, fixing, testing and commissioning of butterfly valve confirming to IS 13095 latest standard, of following sizes as required. Fluid handled: - Water. Maximum working pressure at 20⁰C: - PN 1.6 Service: - Tight shut off. Mode of operation: - Manual with lever. Type of construction: - Wafer. Face to Face Dimensions short series - (200mm dia - 60mm, 150mm dia - 56mm & 80mm dia -46mm). Valve installation: - Horizontal.Material of construction: - Body: - Cast Iron. Disc: - Stainless steel. Shaft: - Stainless Steel. Seating Ring: - EPDM Rubber. Note: -1. For each valve enclose the Hydrostatic Body Test and Hydrostatic Seat test. 262 150 mm dia 263 100 mm dia 264 Providing and fixing of 100mm size cast iron flanged Y strainer with SS304 mesh for suction pipes of pumps with ISI mark etc. all complete as directed by Engineer-in-charge.Note: All the flanged joints shall be paid under relevant items. 265 Supplying and fixing in position of Pressure gauge all Stainless Steel parts (Pressure range 0 to 16 Kg /Sq. cm) of 4 dia including cost of M.S pressure pipe assemblies, one ball valve ( Ø 15 mm (½) all Stainless Steel parts, IS marked complete as required.) adjecent to the dial gauge and M.S specials etc., all complete as directed by Engineer-in-charge. 266 Supplying, fixing and testing of following dia CPVC Ball Valve of approved makeincluding fixing over GI/CPVC pipe using with female ends, screwed bonnet, integral seat, non rising spindle class-I including fixing the valve etc., all complete as per specification and as directed by Engineer In-Charge. 267 25mm dia. CPVC Ball valve 268 50mm dia. CPVC Ball valve 269 Supply and fixing pool water outlets made of ABS plastic with maximum flow upto 9 cum/hr, 2 inch inlet dia on existing CPVC pipeline including providing Tee/Reducer T in pipeline, connections etc as required. Make: Emaux/ Aquanomics. as per direction of Engineer-in-charge.(Floor Inlets For Main Pool & kids pool) 270 Supply, installation, testing and commissioning of liquid hypochlorite electronic dosing pump of capacity 0- 12 LPH at 2 bar pressure rating, Power supply: 230V, AC, 50 HZ, 40 watts Single phase,Antisyphon, stop valve, foot valve/y-strainer, 3m LDPE tubing. Electronically operated Mechanically actuated diaphragm, Manual stroke length adjustable while running. Liquid end body: PP, Valve body: PVC, Ring Seal : Tefflon, Tube : LDPE. 271 Supply, installation, testing and commissioning of liquid soda ash electronic dosing pump of capacity 0- 12 LPH at 2 bar pressure rating, Power supply: 230V, AC, 50 HZ, 40 watts Single phase,Antisyphon, stop valve, foot valve/y-strainer, 3m LDPE tubing. Electronically operated Mechanically actuated diaphragm, Manual stroke length adjustable while running. Liquid end body: PP, Valve body: PVC, Ring Seal : Tefflon, Tube : LDPE. 272 Supply, installation, testing and commissioning of alum dosing pump of capacity 0- 12 LPH at 2 bar pressure rating, Power supply: 230V, AC, 50 HZ, 40 watts Single phase,Antisyphon, stop valve, foot valve/y-strainer, 3m LDPE tubing. Electronically operated Mechanically actuated diaphragm, Manual stroke length adjustable while running. Liquid end body: PP, Valve body: PVC, Ring Seal : Tefflon, Tube : LDPE. 273 PRESSURE SAND FILTER : Supply, erection testing and commissioning of Anti corrosive fiber glass winding design vertical high flow Side Mounted Pressure Sand Filter with diameter - 1400 mm, Over all Height 1350 mm which is durable, deforming- proof and corrosion resistant. It shall have efficient multi - lateral under drain assembly, self-cleaning laterals given totally balanced flow and back washing and a provision to vent the air from the top. Flow/unit - min 75 m3/hour, Filtration area - min 1.5m2, Maximum working pressure - 2.5 kgf/cm2. Inlet and out let Mouth size: 2 inch. Type of Inlet distributor - Multi arm diffuser type made from UPVC and polypropylene, Type of bottom collector - Multi arm diffuser type made from UPVC and polypropylene including all accessories, fittings etc., all complete as per the specification and as directed by Engineer-in-charge. 274 Providing and filiing of Silica Sand for filter with granulometry between 0.4 and 0.8 mm including materials and labour charges completely as required and directed by Engineer-in-charge. 275 Supply, fixing, testing and commissioning ofside mounted 6-position multi port valve made of molded ABS material with heavy-duty plastic handles capable of handling a working pressure of 2.5 kgf/cm2 with a 2 inch sizeinlet, outlet and backwash ports. The valve shall comprise of functions namely Drain, Filter, Backwash, Rinse, Whirlpool, Close. The valve shall be equipped with a precise pressure gauge.
