Tender For Provn Of Certain Sanction Work In The Area Of Age B/R-I And Age E/M (Central) Under Ge (Central) Delhi Cantt-10; 1 Taking down cement or cement lime plaster any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 2 M&L 15mm thick rendering on brick work or concrete surfacesin cement mortar 1:4finished even and fair. 3 M&L for rendering 15mm thick in CM 1:6 on fair faces or other than fair faces of brick work or concretesurfaces of walls firnished even and smooth without using extra cement in multistorey building ,complete all as directed 4 M&L forapplying2 mm thick wall care putty over a coat of cementprimerup to 8 storey bldgcomplete all asspecified and all as directed by Engr- in-charge. 5 M&L fornew plaster surface two coat of oil bound destemperincluding preparation of newly plasteredsurface etc all as specified. 6 M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of cementprimer complete all as specified and directed 7 Complete removal of existing oldtreatment on surface from walls with machenical scraper (machine)complete all as specified and directed. 8 M & Lpreparing old surface includingwashing, rubbing, filling holes,and uneven surfacefinishing old surfaces even and smooth with ,JK/Birla Wall care putty/POP, andsurface shoulld be even and smooth applying onecoat of oil bound distemper on wall surfaces with roller brush of complete all as specified 9 Material and labour for preparation of new plastered surfaces as of walls and applying Twocoats of weather proofing exterior acrylic emulsion paint of DULUXWeather shield Max or APEX ULTIMA from Asian paintover one coat of primer from the same manufacturerwhite lime wash complete all as specified and directed. 10 M&L for preparation of old decoreated/undecoreatedexternal wall / Ceilingapplyingtwo coats of cement base paint by spray gun/ spray machine up to 8 storey bldg complete all asspecified and all as directed by Engr- in-charge.Note :- 1. Stage for prepration of surfaces shall be got approved from GE before applying the finishes.2. Material shall be procured from manufacturer and work shall be got executed through authorised applicator. Note rate quoted up to G+8 bldg including scaffolding 11 S&F curtain rod made out of 20mm dia(outer dia )pipe of stainless steel and havingincluding brackets and knobs complete all as specified and directed. 12 Dismantling floor, hearth or wall tilesincluding cement mortar concrete bedding amdremoving rubbish off the premises complete all as specified and directed. 13 M&L for Non-skid ceramic tiles, coloured, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified. 14 M&L Glazed ceramic colouredtiles (600X300mm) x 6-7mm thick on vertical surfaces etc,set and jointed in neatcement slurry and pointed in white cement to match the shade of tile over 10mm thick rendering of in cement mortar 1:4. 15 Taking down chowkats or frames n.exc. 1.5 Sqm (without taking off shutters from the frame). 16 Taking down chowkats or frames exc. 1.5sqm but n.exc 4 Sqm eachwith shutters (without taking off shutters from frames ), complete all as specified. 17 S&F pressed steel frames,size 125x60mm for doors with one or more rebatesfabricated out of 1.25mm thick sheet including necessary fixing lugs, hinges, lock strike plate etccomplete all as specified and directed by Engr-in -charge. 18 S & F 30 mm thickflush shuttersolid core construction, with block board core and plywood face panels,commercials type on both sides complete all as specified. 19 S&F factory made 35mm thick second class hard wood Glazed and skelton door shutters , open rebated and prepare to receive glass, gauge etc, size of members of shutters as specifed in SSR part I, section 8 clause 8.24(b) 20 M&L aluminium alloy powder coated windows including aluminium coated frames silding track, bottom weighing not less than 1.015 Kg/Rm ,sides and top not less than 0.826 kg/Rm double revated and 0.55 kg/Rm for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter silding type with aluminium sectins as per series-A (15mm) 3 track of jindal section number for silding windows with framed shutter including aluminium allow powder coated snap type beads handles with locking arrngement spring action and glazingclips joint cleats rubber gaskets etc inclding provision of 4.5 mm thick tinted frosted glass of superior quality and stainless steel jail including all standard fittings complete all as specified and directed 21 Anodised aluminium powder coated sliding windows, window shutters and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as locking system, suitable handle (1 no.)complete all as specified and as directed by Engineer-in- charge. 22 S&F 4.8 mm thick sheet glass, ordinary quality and glazing in Aluminium door with solar control files 50 micronin squares exc 0.5 Sqmeach pane. 23 S&F galvanised mild steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm & fixed with tinned tacks or galvanised wire staples. 24 M&L two coats of synthetic enamel painting on wooden surfaces not otherwise described over 10cm width or girth over a coat of pink primer inclding prepration of newly untreates surfacescomplete all as specified and directed. 25 S&F150mm long extruded alumiunium alloy handle fabricated type anodized (D type). 26 S&F 100 mm long(size)butt hinges medium weight, cold rolled,mild steel, complete all as specified(Fixing included in item 43 here-in-before). 27 S&F for 150 mm size aluminium, anodised barrel tower bolts of extruded section and fixed to shutter complete 28 S&F 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed. 29 Supply&fix in repairs two legged aluminium floor door stopper with rubber shoe 140mm long complerte all as specified and directed by Engineer-in-Charge. 30 S&F MS butt hinges medium wt of size 100 mm complete all as specified and directed. 31 S&F in repairs bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium platedlong body with flange complete all as specified. 32 Supply and fix in repairs chromium plated brass angle valve suitable for 15mm bore pipe, complete all as specified. 33 S&F in repair 15mm dia chromium plated wall mixer hot & cold L bend 3 IN 1 pattern fixing and connection to pipes complete all as directed. 34 S&Fin repair 15mm dia brass chromium plated mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB, complete all as specified. 35 S&F in repairs CP Brass shower rose 125 mm size suitable for 15mm bore long pipe pipe complete all as specified. 36 S&F in repair pvcfloor trap square type with Cockroch Proofing CP grating with or without hole including provision ofjointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified. 37 S & F in repaircp health faucets with crutch or push handle, screwed down with 1.5mtr CP flexible pipe, screwed for pipe, 15mm dia, fancy type, cast copper alloy. Chromium plated long body completeall as speciifed. 38 S & F in repairs glass corner 300 mm radius of 10mm thick toughned glasswith CP Brassrailng, fixed with screws fancy type, complete all as specified 39 S & Fixedin repairpvc mirror cabinet made of high intensity polythene of biggar size 500 x 400x120 mm complete all as specified 40 S&F CP connection pipe of 15mmx 450mm with CP check nuts with washers, complete all as specified. 41 S&Fin repairbrass chromium platedtoilet paper holder, complete all as specified. 42 S&F in repair brass chromium plated soap dish, complete all as specified. 43 S & F in repairsbrass chromium plated towel rack 600 mmsize including a pair of CP brass bracket complete all as specified and directed. 44 S&F in repair stainless steel peg set of 06 peg, 45 centimeter long, complete all as specified. 45 S & F in repairs 900mmx600mm bevelled edge lookingmirror of selected quality glass,fency type with 100 mm border fixed to four Nos stainless steelbracketswith stainless steelscrews and cup washers. 46 S & F in repairfor floor mounted EWC one piece incl all necessary fittings complete all as specified and directed by Engr -in-charge. 47 Supply & fixing vitreous china wash basin, white, flat back of size 550mm x 400mm with Pedestal including 32mm dia PVC flush pipe with coupling and set of brackets inclPVC connections 15mm size with PTMT nuts of legth 450mm complete all as specified and directed by Engineer-in-Charge. 48 Dismantling false ceiling boards/ wall pannel any description and in any position incl frame work. 49 S&F anodised aluminium snap grade of size 600 X 600mm frame work for false ceilingincluding hangers 6mm dia G I (upto 1200mm length) asjusting level fixed to roof slabs by means of ceiling cleats made out of G I flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long.and Exposed metal frame ceiling with 8mm thick calcium silicate board of silicious and calcareous material reinforced with cellulose fibre for fixing in 600mmX600mm grid (frame work for ceiling shall be measured and paid seprately) all as specified 50 M&L for brick work with subclass B bricks, straight or curved on plan to any radius in half brick thick walls with old size bricks, built in cement mortar1:6, complete all as specified. 51 Dismantling of plain or corrugated steel sheeting, any guage, thickness from roof covering complete all as specified. 52 S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. 53 S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. 54 Dismantling wrought iron or mild steel work of any description not otherwise provided. 55 S&F Mild steel rolled section or hollow pipes( square or round pipe)as in main and cross beam, hip and jack rafter, purlins, where connected to common rafter and running rails fixed with cleat or other connecting plates etc. complete all as specifed and directed 56 M&L two coats of syntheticenamal paint to steel surfaces of any discription over 10 cm width or girth not otherwise described after preparation complete. 57 Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level). 58 M&L 75mm thick PCC 1:3:6 Type C-1 using 20mm crushed stone aggregate as in plinth protection and finished even and smooth without using extra cement. 59 S&F in repair 110 mm bore, PVC (SWR) pipes single socketed, in anylength with rubber ring joints, laid as rain water pipe dismantling old one complete all as specified. 60 Taking up or down steel tubing 15 mm bore, and connections, including cleaning for re-fixing or removal to store in repairscomplete all as specified. 61 S & F 15 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor in repairscomplete all as specified. 62 Taking up or down steel tubing 20 mm bore, and connections, including cleaning for re-fixing or removal to store in repairscomplete all as specified. 63 S & F 20 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor in repairscomplete all as specified. 64 Excavating in post holes each n exc 0.5 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceedings 25cm watering and removing surplus soil to distance n exc 50 m and making good surfac in soft/loose soils 65 M&L forPCC 1:3:6 type C-2 (40 mm graded agg)for post holes/ Roof correction/ foundation/mass concrete complete all as specified and dircted. 66 S&F powder coated Anodiesed aluminium frame for partition, doors, windows, ventilators with one or more rebates incl. joining cleat for fixing etc. complete all as specified. 67 S&F powder coated Anodiesed aluminium door shutters, aluminium section weighing 0.55 Kg/m incl. necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each doors,Brass 2 lever mortice lock verticle type size 100mm, hinges, anodiesed aluminium snap beading screw withetc. 68 Supply and fixing PVC sheet consisting of 5mm thick light colour PVC sheet inclusive of fixingon PVC frame /Aluminium frame at site etccomplete all as specified and as directed by Engineer-in- charge. 69 S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS :1868 with minimum anodiccoating of grade AC 15) of approved design/pattern, with approved stadandered section and fixed to existing window frame with CP brass/stainless steel screws @200mm c/c, incl cutting the grill to proper opening size for ficing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement and direction of Engineer-in-charge. 70 S&F door closer aluminium (extruded section) hydraulically regulated designation No. 03, universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 Kgs. 71 S&Fsteel work as in posts and struts , flats in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 72 Dismantling and Re-Fixing only chain link fencing incl line wires, any mesh, size and type to any type of standereds, rails, straining blots, etc. incl provn of binding wire. 73 Supply & Fix chain link MS galvanised fencing any size (50x50mm)or any type complete. 74 M&L, two coats of synthetic enamel paint to untreated surfaces of steel any size width or girth not otherwise described over a coat of red oxide primer after preparation 75 S&F 2mm thick fibre glass reinforced translucent plain sheeting withside lap fixed with srew. 76 Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed. 77 M&L hard core of broken stone of gauge n. exc. 63mm; deposited, spread and levelled in layers n. exc. 15cm thick watered and rammed to true surface complete all as specified and directed by Engineer-in-Charge. 78 M&L chequered tiles 30cmx 30cmx 10mm thick,set, jointed & pointed in neat cement slurry in floors with grey cement and pigments over & including 15mm thick screed in cement mortar 1:6. 79 S&F mild steel, plain black sheet 1.25mm thick in wall clading, steel gates incl round headed screws, clout nails or rivets and fixed to wood or steel framing. 80 S&F WPC board, S&F factory made 18mm thick single extruded WPC (Wood Polymer Composit) Solid Board having density not less than 600 kg/ Cbm one side white and other side of board laminated with PVC Foil including finishing all edges at all level for making edge lipping /beading or 0.50 mm thick PVC sheet lipping at all 4 edgesusing binding tape, Solvent, screws, stainless steel, Piano hinges / self closives box type hinges etc Manufactured by ISO 9001-2008 certified company. raj shree or equivalent. 81 S&F75mm long, extrruded fancy type SS handle for kitchen cup boards shutters, cabinets, crocery shelf drawers fixed with nuts, screw and washer of mild steel bright finished, complete all as specified. 82 S&F in repairs magnet catchesand striking plate including letting in and fixed, complete all as specified. 83 M&L providing and applying the plaster with single component ready to use repair mortar (SMART CARE REPAIR MORTAR or equivalent) capable of applying 15mm average thickness in single layer and finishing with trowel with a bond coat: SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement/Sqm of surface area mixed with specified portion of AP SMARTCARE or equivalent Repair Polymer including taking down existing roof treatment of any type including raking out joints, hacking for key, scrubbing down with water etc., to receive further treatment, complete all as specified land as directed.Note: The application shall be executed on any type of surface and on horizontal/Vertical areas. 84 M&L providing and applying Smartcare Dampproof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajas in multiple coats @2.0 litre/sqm. Primary [coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge.Notes: (1) The work shall be executed through authorised applicator of manufacturer only.(2) Authrised Applicator shall be approved by GE before starting of work.(3) All materials shall be procured directly form manufacturer. The purchase voucher shall be produced to the Engineer-in-Charge for his verification of material.Engineer-in-Charge shall deface the original purchase vouchers.(4) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of 10 (ten years) in favour of the GE. A sum equivalent to 3% (Three Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractors dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer. 85 Fixing only 15 mm water tubes, any grade, to walls and ceilings or laying in floorsin repairscomplete all as specified. 86 Fixing only 20 mm water tubes, any grade, to walls and ceilings or laying in floorsin repairscomplete all as specified. 87 S&F PVC (SWR) bend any radius 110mm bore complete all as specified and directed 88 S&F Framed mild steel work as in doors or gates of angle or other sections with gusset plates, rails, braces, tank stagging etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails and gurders) and hanging also fastening and complete all as specified and directed (Fe-410-W(Gde E-250)Quality-A). 89 M&L for preparation of new or previously untreated steel surfaces over 10cm in width or girth and applying two coats of syanthetic anamel paint over one coat of red oxide Complete all as specified and directed by Engineer-in-Charge. 90 Supply and fixing PVC wall lining consisting of 5mm thick printed colour PVC sheet inclusive of solvent cement and fixingon PVC frame /Aluminium door at site etccomplete all as specified and as directed by Engineer-in- charge. 91 S & F Steel work in tubular trusses, vertical posts , purlins etcincluding special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 gradeSt.-240 complete all as specififed and dircted by Engr-in-Charge. 92 M&L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete all as specified. 93 Sand filling under floors or in foundations incl. watering and consolidation. 94 M&L 60mm thick interlocking paver block with grey cement and with pigment of any size and shape confirming to IS 15658-2006, M-35 Grade as approved by E-I-C laid in flooring and joints filled/broomed with fine sand. 95 M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggrgate as in coping to wallcomplete all as specifed and as directed. 96 S&F steel windows with side hung shutters incl box type hing, steel handle and peg stay complete with glazing bar 97 All as per above itme Ser No 102but without glazing bars 98 S&F Modular Cabinet Kitchen accessoriesof Stainless Steelgrade-304,6mm size rod thicknessincluding :-(i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket,(iv) Cup & saucer basket, (v) Glass basket,(vi) Plate basket, (vii) Premium magic corner(viii) Oil Pull out Tray ( Triple basket layer) , (ix) Dust bin, (x) Cleaning kit rack of size as per site requirement all spd and directed by Engr in charge 99 S & F50 mm dia Galvanised Iron steel tubing, medium grade as in spout in short length, complete all asspecified. 100 S&F in Soft closing ball bearing telescopic channel of size 22 inch long fixed with screws in cupboards incl all fittings complete all as spd and directed by Engr in charge.Note : Runner/ Channel should be SS 304 grade and load capacity should not be less than 45 kgs 101 S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbmhaving good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen and Cabinets. 102 M&L for 22 to 25mm chequered ultra tiles over 15 mm thick screed bed in cm 1:6 and jointed and pointed in white cement mixed with pigment to match the shade of tiles of flooring all as directed. 103 M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar (1:4) complete all as specified and as directed. 104 M&L for Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channelor flat sections) includingdistance pieces, cleats etc.Fe 410 -W (GdeE- 250) quality A all as specified and directed. 105 M&L 100 mm thickPCC(1:4:8) type D2 using 40mm graded stone aggregate as in sub base of floor and filling as mass conc. 106 S & F Expanded metal n exc 4 kg weight per square meter, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members all as specified and directed. 107 M&L for rendering 15mm thick in CM 1:4 on fair faces or other than fair faces of brick work or concrete surfaces firnished een and smooth without using extra cement up to hieght of four storey ,including scaffolding complete. 108 Disconnecting existing tanks of cap 1000 ltrs, setting aside (or lower ing if required) for repairs, cleaning, etc. and hoisting if required re- connecting and re-fixing in position and Cleaning and removing all scale and dirt, etc. from tanks and form mouths of circulating pipes, etc. 109 S & Fin repair 1000 ltr capacity three layer white colour rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling old water tank all as specified in SSR Part I(Make : Sintex/Rotex/Polywell) 110 S & F in repair500 ltr capacity three layer white colour rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling old water tank all as specified in SSR Part I I(Make : Sintex/Rotex/Polywell). 111 Providing cement concrete type C-0 1:3:6 (12.5 mm graded agg) as for pressed steel chowkhats. 112 S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain glover PVC sheet reinforced with MS square tube in opening as per specification and drawing. 113 S&F factory made soilid panel PVC Door shutter 30mm thick (Stype) consisting of frame made out MS frame shall be covered with heat moulded plain coloured PVC C channel having PVC sheet stripof 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, & bottom rail; Panneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing. 114 S&F 125mm aluminium handles, cast type ,anodised and pattern/design as approved. 115 Taking down carefully copper/aluminium point wiring ( light, fan , socket or power) complete fittings fixture such as switches Ceiling roses, pen dents regulators, sockets etc to be measured separately and making good disturbed surfaces of walls, floors etc. 116 Taking down old MCCB , TPN DBs , SPN DBs & main switch/ enclosure box of any make and type from the site and making good surface complete all as specified and directed. 117 Taking down old submain wiring of any size and make from the site and making good surface complete all as specified and directed. 118 M & L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non-metalic rigid new PVC conduit medium grade ISI Marked not less than 20 mm dia and all conduit accessories concealed in wall on surface in ceiling/fixed to roof/truss/columns etc and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty, fabricated modular metal flush box, concealed in walls with suitable modular inner and outer plate for housing switches , socket out let and fan regulators etc, complete all as specified. 119 One light/fan/bell point controlled by one by one way switch ( switch to be measured and paid separtely) 120 One 3 pin socket outlet 5 hole 5 Amp independent including PVC unsheathed copper conductor 1.5 Sqmm cable asearth wire connected to common earth and to earth dully socket & switches to be measured and paid separately. 121 All as per above item ser No 118(b) but Same board. 122 All as per item No 118 above but point wiring with 4 Sqmm single core copper cable and earth continuity wire with 2.5 Sqmm single core stranded copper cable for one three pin 15/16 A socket outlet point on independent board complete all as specified and directed by Engineer in charge. 123 M&Lpoint wiring with PVC unsheathed multi stranded copper conductorcable 2.5 sqmm FRLS 1100 Volts in New PVC concealed conduitmedium grade ISI Marked not less than 20 mm dia in new M S steel terminal boxes modular including one run of using 2.5 sqmm FRLS 1100 Volts copper conductor cableas earth continuityconnected to common earthfor one 15 A switch socket power point, all as specified. 124 M&L for submain wiring with two single core PVCinsulated FRLS 1100 Volts unseathed stranded copper conductor cable 4 Sqmm in and including PVC conduit for submain wiring and connection complete including rigid PVC conduit FRLS grade,unsheathed copper conuctor cable of 4 Sqmm size stranded conductor as earthwire. 125 M&L for submain wiring with two single core PVCinsulated FRLS 1100 Volts unseathed stranded copperconductor cable 6 Sqmm in and including PVC conduit for submain wiring and connection complete including PVC unsheathed copper conuctor cable of 4 Sqmm size S/C as earthwire. 126 M&L switch modular flush type 5 Amp SP one way . 127 M&L switch modular flush type 15 Amp SP one way. 128 M&L Modular socket outlet 5 pin 5 Amp modular type . 129 M&L Modularsocket outlet 2 in 1,3 pin 5/15 Amps modular type. 130 M&L ceiling rose 3 phase PVCpolycorbonate,isolated body. 131 S & F electronic fan regulator 5 stepsingle module connecting complete all as specified. 132 M&L bell push,modular type,6 amp, 1 moduleISI marked complete all as specified. 133 M&L bell ding dong AC,230 volts,single pole 134 M & L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to earth lead GI 4mm dia by means of bolts, nuts,check nuts and washers of galvanized iron and connection to main switch board of panel, including watering pipe GI 20 mm bore light grade 15mm bore for earthing lead, wire mess, funnel, salt, charcoal dust, excavation and refilling pit with PCC 1:2:4 type B1(using 20mm dia stone aggregate) reinforced with 6mm dia round bar @ 75mm cement concrete both always with MS handle 12mm dai and frame all as shown in electric plate No 3 in page 497 of SSR Part I (2009) including testing ion completion all as directed 135 Supply and fixMCB DB SPN 8 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCBSPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete all as specified and directed . 136 M&L MCB SPN 40 Amp B curve all as specified and directed . 137 M&L MCB SP 6 to 32 Amp B curve all as specified and directed . 138 Supply and fix in replacement LED batten luminaire surface mounted, 4 feet system wattage of 20 Watts with lifetime of 25000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.9, THD< 10%, colour temperature - 6500K, surge protection 2.5KV in CM, IP-20 protected, meets LED IS specifications, Class - 1,Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level ≥ 110 Lumens/watt andincluding connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed completeallas specified and directed. 139 S&F in replacement of LED batten luminaire surface mounted 2 feet system wattage of 10 watts and not less than 110 lm with life time of 25000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.90, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, system efficiancy at luminarie level ≥120 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed. 140 Supply and Fix 35/40 W High efficient LED Street light fitting with pressure die cast LM6 Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover.System level efficacy of the Luminarie is 100lm/W with a life class of 25,000 burning hours at L70.The color temperature is around 6500 K with a color rendering index of 70.The luminaire is IP:66 protected with IK05 impact resistance.It has an electronic driver complaint to IEC safety standards with a power factor>.0.9, voltage variation range 120-270V, THD<20%, High and low protection along with a surge protection of 4 KV including provision of 40mm dia GI light grade pipe1.5 meter length bend to shape and necessary clamps etc for fixing the light fittings on pole fixed complete as specified and directed. 141 Supply and fix in repairs LED 2 X 2 ft backlite surface mounted fitting 36/40 Wattsincluding connecting up with necessary PVC sheathed 3 core 1.5 Sqmmcopper conductor flexible wire fixed complete. 142 M&L in replacement Decorative wall mounting CITY-1 Decorative wall light fixture made up of Polycarbonate, Including 12 W retrofit LED BULB (B-22 base). NOTE-1: Piece of LED bulb included with city -1 fitting. 143 Supply and fix in replacement 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 100 lm/W with a life class of 50,000 burning hours at L70 criteria,Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<20%, CRI>80, Color Temperature-6500K, Surge protection of 4.0 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmmcopper conductor flexible wire fixed completeallas specified and directed. 144 Supply & fix in repair factory made epoxy powder coated Distribution Board VTPN-4 ways (IP-54 protection), mechanical impactstrength IK - 09, with cement spill protector double doorfabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with knockouts and suitable for one MCCB 125/160 Amp as incomer and 40 to 63 Amp SP MCBs outgoing complete all as specified and conforming to HSN code : 8537. Cat Part No : 812040Note :- MCCB & MCB will be measured & paid separately. 145 M&L in replacement MCCB 125 Amps, 415 volts, 16 KA , 4P, optium 2.0 adjustable thermal settingIcs=100% Icuas per IEC 60947-II suitable for isolation , fixed over load and fixed short sircuit setting complete all as soecified & as directed 146 S&F modular type sheet metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 20 Amp 230 volts, 50 Hz, 10KA breaking capacity complete. 147 Provision of exhaust fans metal body AC single phase 230/240 V of size300 mm sweep, 4 numbers of bladeAir flow rate > 900cum/min, Bird screen forprotectionagainst birds, double ball bearing, metal body with louvrewith louvre for fixing of exhaust fan complete all as directed by Engr-in-Charge. 148 Provn of fresh air fan PVC body air delivery > 800 CMH ,with copper winding, 5 number of blades, AC single phase 230/240 V of size 250 mm sweep with louvre fixed complete with suitable size ply by cutting into suitable size as required complete all as specified and directed by Engr-in-Charge. 149 M&L for breaking the old existing wall and makingprovn of a round hole for fixing of 300 mm sweep exhaust fan including making good to the disturbed wall/ portion and matching with existing colour.all as specified and directed. 150 Supply and fixing NEW BLDC ceiling fans against old fansAC single phase 230/240 V of size 1200 mm sweep ,min air delivery 210 CFM with service value 6.0 BEE, 5 star rated BLDC fan including making connection with three core flexible, copper cable pvc insulated of suitable length and marking of fan no with black paint complete all as directed by Engr-in-Charge. 151 S&Fswitch Modular type 6 Amps 1 Way,1 module, 230V AC complete all as specified and directed by Engineer in charge. 152 M&L for switch Modular type 16 Amps 1Way, 1 module with modular plate light marking 230V AC complete all as specified and directed by Engineer in charge. 153 M&L in replacement Modular socket outlet 2/3 pin 6/16Amp universal socket 2 module complete all as specified and directed by Engineer in charge. 154 S&F Modular socket outlet 2/3 pin 6 Amp socket 2 module complete all as specified and directed by Engineer in charge. 155 Suppy & fixing DBOXx MCB Protected Socket 15 Amps , PVC Plastic Base (white) with Plug top 25 Amps & MCB SP 32 amps complete all as specified and directed.Make : Anchor Roma /Legrand/indoasian.Note : 15 A switch to be provided near wash basing and separate socket to be provided near geyser rate to be included in quoated rate same for AC also. 156 Supply and Fixing wall mounted angular Electric chimney black colour of suction power not less than 1220Cum/Hr,Al casette with stainless steel outer layer ,touch control panel,3 speedmotor with 250 watt with decorative smart cooker hood SS and glass ,energy efficent Led light with digital display , including ducting not less than 12 feet as per site required complete all as specified and as directed by Engr-in-Charge. 157 Supply and fix wall mounted fan 400mm size, 230 volts , 50 Hz 1420 RPM with 90 degree oscillation and having speed control by pull cord (two) system complete all as specified and directed. 158 Supply and fix Instant Hot Water Geyser 3 Ltrs capacity,3 KW with corrosion proof thermoplastic external body ,withstand high pressure capacity to use in high rise buildings, ISI approved with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connectioncomplete all as specified 159 Schedule of Credit
