Certain Special Repairs And Revenue Work Under Age B/R I And Age B/R Ii At Bb Cantt, Srinagar; 1 Surface dressing not exc 30 Cm and averaging 15 cm deep and getting out in soil, complete all as specified and directed . 2 Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depthforfoundation,laying of cables etc and getting out in soft/loose soil, complete all as specified and directed . 3 M & L Plain cement concrete (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete, complete all as specified and directed . 4 Form work to sides of concrete foundation , footings, bases of columns, plinth beam etc, vertical or to batter, complete all as specified and directed . 5 M & L for reinforcedcement concrete 1:2:4 type B1 using 20mmgraded crushed stone aggregates as in foundationfootings, foundation beam,plinth beams and bases of columns basement slabs, and mass concrete, complete all as specified and directed . 6 Form work to sides and soffits of floor or roof beams, beam, lintels, cantilevers etc, fair finished surface, complete all as specified and directed . 7 M&L for Reinforcedcement concrete 1 : 2 : 4 Type B1 using 20 mm graded crushed stoneaggregates as in roof beams, cantilevers , bressummers, lintels over 1.5 m span, complete all as specified and directed. 8 Form work to sides of pillars, posts, struts, piers, columns, fair finished surface, complete all as specified and directed. 9 M & L forReinforcedcement concrete 1 : 2 : 4 Type B1 using 20mm graded crushed stone aggregate as in columns pillars, piers, posts and struts, complete all as specified and directed . 10 S & FTMT steel bars 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia but in stirups, complete all as specified and directed . 11 S & FTMT steel bars 6 to 8 mm dia in stirrups, spacers and binders cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia, complete all as specified and directed . 12 Returning, filling in, including spreading levelling, watering and well ramming in layersnexc25 cm in soft/loose soil, complete all as specified and directed . 13 Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point, complete all as specified and directed . 14 M & L brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1 : 4, complete all as specified and directed . 15 M& L forRoof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Gde Fe 410-W (Gde- E-250) Qty-A, complete all as specified and directed . 16 S & FPre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed . 17 S & F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an strength of 550 Mpa as in roof covering/cladding to wall and as in eaves bd etc, fixed with self tapping screws, complete all as specified and directed . 18 M&L forpreparation of newsteel & iron surfaces of any description over 10cm width or girth and applying Two coat ofsynthetic enamel paint over a coat of red oxide complete all as specified and directed (Bldg upto & including 3 storey), complete all as specified and directed. 19 M & L for 15mm thick rendering on other than fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth with out uing extra cement, complete all as specified and directed . 20 M & L for 10mm thick rendering on fair faces of brick work or concrete surface in cm 1:6 to be finished even and smooth with out uing extra cement, complete all as specified and directed . 21 M&L forPreparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer , complete all as specified and directed . 22 M & L for preparing newly plasteredsurfaces of walls and applying two coats of oil bond distemper over3mm wall care putty on wall, complete all as specified and directed . 23 M & L for broken stone hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface, complete all as specified and directed . 24 M & L forplain cement concrete1:3:6, type C-2 using 40mm graded crushed stone aggregate 75 mm thick as in plinth protection / hard standing etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2, complete all as specified and directed . 25 M&L for Non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm and n.exc 0.36 sqm as , in floors etc. set and jointed withneat cement slurry and pointed in white or coloured cement to matchthe existing surface over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 , complete all as specified and directed. 26 M&L for Vitreous china water closet pan (pedestal pattern), white with seat cover and hinging device ,fixing bolts etc (excluding flushing cistern and including flush pipe), complete all as specified and directed . 27 M&L for Vitreous china bowl urinal flat back,of size 465x355x265mm white (minimum), with grating and union for discharge pipeincluding providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and includingdischarge pipe of PVC 32mm dia, complete all as specified and directed . 28 M&L Glazed ceramic colour tiles in vertical surface 350x 250x 7 mm/ 450X350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the shade oftile laid overand including 10mm thick bedding layer in cement mortar 1:3, complete all as specified and directed. 29 S&F vitreous china wash basin, white, flat back, size 550x400mm including waste chain & plug and porcelean stopper and including brackets, waste pipe etc,complete all as specified and directed 30 S&F 10 Litres capacity PVCvalveless syphonic action type flushing cistern,low level white with inlet ball valve float and handle including brackets , with flush pipe etc fixed, complete all as specified and directed . 31 S & F for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed . 32 M&L for Stop/Angle valve 15mm bore, cast copper alloy screwed down, high kpressure, with crutch jor butter fly handlel, screwed bosth ends for iron pipe or for unions, complete all as specified and directed . 33 S&FPVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement, complete all as specified and directed . 34 S&F PVC connection 15mm dia and 600mm long with PTMT nuts and washer, complete all as specified and directed . 35 S&FCP fancy type mixture tap of standard quality for mixing hot & cold water (WHB)as approved by Engr-in-Charge with centre hole mixer with fittings, complete all as specified and directed . 36 S&F 110mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall /floor /laid in trenches etc, complete all as specified and directed . 37 S&F 110mm bore PVC (SWR) bend or tee anyradius, complete all as specified and directed . 38 S&F PVC gully trap square or round mouthed type (P) , size of trap 125x 110mm and jointing to drains with solvent cement, complete all as specified and directed . 39 S&F Bib tap 15mm bore (ISI marked) cast copper alloy chromium plated fancy type with crutch of butterfly handle, screwed down, screwed for iron pipe orfor brass ferrule and fixed , complete all as specified and directed . 40 S&F 75mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall /floor etc, complete all as specified and directed . 41 S&F 75mm bore PVC (SWR) bend or tee ofradius, complete all as specified and directed . 42 S&F 600x450 mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed . 43 S & F tubular towel rail 60cmlong, aluminium anodised fixed with and includingCP brass screwsand wooden/plastic cleats, complete all as specified and directed . 44 S&F GI steel water tubing 20 mm bore medium grade galvanized with all fittings and fixed to walls, ceilings or laid on floors, , complete all as specified and directed . 45 S&F GI steel water tubing 15 mm boremedium grade galvanized with all fittings and fixedto walls, ceilings or laid on floors, complete all as specified and directed . 46 M&L Lagging to pipes 15mmdia used in internal water supply or plumping all round with,25mm thick bonded mineral wool preformed SNAP ON pipe sections of density 144 kg/cum conforming to IS-9842, complete all as specified and directed . 47 M&L Lagging to pipes 20mm dia used in internal water supply or plumping all round with,25mm thick bonded mineral wool preformed SNAP ON pipe sections of density 144 kg/cum conforming to IS-9842, complete all as specified and directed . 48 S&F,rotional molded polythylenewater storage tank 1000 Litrescapacity (Cylinderical vertical with closed top) hoisted kand fixed in position, complete all as specified and directed . 49 S&F 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms), complete all as specified and directed . 50 S & FGun-metal, globe or gate valves 20mm dia , with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed . 51 S & F Gun-metal, globe or gate valves15 mm dia , with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed . 52 S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of Gde 410-W (Gde-E-250)Qty-A, complete all as specified and directed . 53 S&F 16mm dia mild steel screw bolt (machine made) with hexagonal or square head at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal and one squarenut not exceeding 5cm long, complete all as specified and directed . 54 S & F aluminium powder coated ventilators made of thefollowing specifications :- (Net external size of ventilator shall be measured, complete all as specified and directed . Following items are included in the unit rate.)(a)Aluminium frame powder coated stiles, bottom, top and middle rail of hollow section 50 mm x 25 mm x 1.80 mm thick.(b)Lower portion of ventilator shall be fixed with 3 mm thick pin headed glass fixed with suitable aluminium beading clips and EPDM beading (rubber).(c)Upper portion shall be fixed with aluminium powder coated louver guides fixed with 3 mm thick pinheaded glass with suitable EPDM beading incl suitable handle and clips.(d) Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with suitable frame in upper panel.(e) Repair to the jamb, cills and all sides around the window is incl in unit rate.The repair finishes to match the existing surfaces like tiles, plastering etc. 55 Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed . 56 S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed . 57 S&F butt hinges, medium weight cold rolled, mild steel of size 100 mm, complete all as specified and directed . 58 S&F 100 mm long aluminium barrel tower bolts of extruded section and fixed, complete all as specified and directed . 59 S&F100 mm aluminum alloy handles, fabricated type, anodised, complete all as specified and directed . 60 M&L for 75 mm thick plain cement cencrete1:3:6type C-2 using 40 mm graded crushed stone aggregate as in sub base for floors etc, complete all as specified and directed . 61 M&L for 25mm thick plain cement concrete type B-1, 1:2:4using 20 mm graded crushed stone aggregate as in sub base under floor and finished rough surface, complete all as specified and directed . 62 S&F 6MM thick Non asbestos fibre cement designer board /pre Laminated self embossed texture designer board E-Board classic size 600x600 m ,HPSC (High pressure steam cured) to be fixed or inserted to pre laminated GI Frame work for Seamless ceiling size 600mmx600mm with main runner 38x24x0.9mm thick cross tee 8.6x0.9mm and wall angle 19x19x0.9mm duly suspended with 6mm dia GI bar hanger 1200mm centre to center both ways fixed with steel dash fasteners or from purlin from the roof with alignment dip complete as per manufacturers instructions, complete all as specified and directed . 63 M&L Glazed coloured Chequered cement concrete tiles 25 cm x 25 cm x 22 mm thick, set, jointed and pointed in neat cement slurry (with grey cement and pigment) as in floors over and including 15mm thick screed bed or bedding layer in CM 1:4, complete all as specified and directed . 64 M&L for plain cement concerte 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in cills, steps, seismic and other similar bands, plinth courses, copings, kneelers, apex stones, bed plates, bond stones etc. including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed 65 Taking down frame with shutters (without taking off shutters from frame)n.exc 1.5 sq.meach , complete all as specified and directed . 66 Taking down frame with shutters (without taking off shutters from frame) exc 1.5 sqm but n.exc 4 sqm each , complete all as specified and directed . 67 S&F for 2nd class hard woodPlain, solid, straight chowkats and frames, wrought,framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed . 68 M&L for 35mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln easoned and chemically pressure treated, complete all as specified and as directed 69 S&F 30mm thick 2nd class hardwood factory made glazed and skeleton door/window shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete all as specified and directed . 70 Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and directed . 71 M&L 6mm thick Non Asbestos fibre cement /Pre Laminated self embosssed texture designer board E-Board classic size 600x600mm, HPSC (High pressure steam cured)to be fixed or inserted to pre laminated GI frame work for seamless ceiling size 600mm x 600mm with main runner 38x24x0.9mm thick, cross tee 8.6x24x0.9mm and wall angle 19x19x0.9mm duly suspended with 6mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip, complete all as specified and directed . 72 S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed . 73 Descriptiion all as per serialitem No 57 here-in-before but 75mm size, complete all as specified and directed . 74 S & Fextruded aluminium handles fabricated type, anodised ofsize 150 mm, complete all as specified and directed . 75 S & F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple & fixed clips of sheet, cast or extruded section & fixed bolts & sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed . 76 Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc , complete all as specified and directed . 77 M&L for brickwork with old sized subclass B bricks straight or curved on plan exc 6m mean radius and built in CM 1:6 etc, complete all as specified and directed . 78 Taking down cement plaster of any description, on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed . 79 M & L for rendering 15mm thick cement plaster in CM (1:6) on brick work or concrete surfaces finished even and fair without using extra cement, complete all as specified and directed . 80 M & L for rendering 10mm thick cement plaster in CM (1:4) on brick work or concrete surfaces finished even and fair without using extra cement, complete all as specified and directed . 81 M&L for coloured glazed ceramic tiles of size 350x 250x 7 mm/ 450X 350X 7mm / 200x 300x 7mm thick as invertical surfaces set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick backing coat in CM 1:4,including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc , complete all as specified and directed. 82 M&L coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6,including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc,complete all specified and directed. 83 M&L for vitrified ceramic tiles, 8-10mm thick (square/rectangular), area of each tile n.exc 0.36 Sqm, as in floor etc, set and jointed with neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over and including 15mm thick screed bed or bedding layer in CM 1:4 including Dismantling floor, hearth or wall tiling,complete all as specified and directed . 84 Hacking out old broken glass (any thickness size quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones, complete all as specified and directed . 85 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc.,complete all as specified and directed. 86 S&F 110 mm dia PVC (SWR) pipes including necessary bends, fittings etc single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. 87 Description all as per serial item No86 here-in-before but 75mm size, complete all as specified and directed . 88 S&F in repairs 15mm bore Bib taps, chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule etc, complete all as specified and directed. 89 Dismantling of plain or corrugated steel sheeting, anygauge thickness , including nanital or similar pattern roof covering, complete all as specified and directed. 90 S&F 0.63 mm galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roof, wall etc with grade of zinc coating 275, complete all as specified and directed . 91 S&F 0.63 mm Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, fixed with coach screws and washers, in roof, wall etc, complete all as specified and directed . 92 S& F in repair Cast iron floor trap, with grating including jointing to waste pipe fixed in plain cement concrete(1:2:4) type B-1 using 20mm graded crushed stone aggregates of 75 mm dia etc, complete all as specified and directed . 93 Preparation of newly plastered of wallssurfaces by using necessary filling compound of Altek/Birla white 1mm thick wall careputty to obtain smooth/even surface using sand paper and applying two coats of oil bound dismater over a coat of primer, complete all as specified and directed . 94 Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50micron)work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections/ 3 truck and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed . 95 M&L for rubber moulded chequered cement concrete tiles 30cmx30cmx25mm thick with grey cementandpigments over 20mm thick screed bed or bedding layer in cement mortor (1:6) over 75 mm thick PCC (1:4:8) type D2 (using 40mm crushed stone aggregate),set, jointed and pointed in neat cement slurry including demolition/Dismantling of tiles, complete all as specified and directed . 96 S&F powder coating of any colour (Thickness or powder coating not less than 50 micron Anodised aluminium window and ventilator shutters, fixed type/sliding type/side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handle, locking arrangement etc, complete all as specified and directed . 97 Demolition of Cement Concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed . 98 M&L for Reinforcedcement concrete (nominal mix)type B1 1:2:4 using 20mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including use and waste formwork up to 6m height, complete all as specified and directed. 99 Dismantling wrought iron or mild steel work of any description ,complete all as specified and directed 100 S&F for Framed brackets of angles or tees with web and flanges, tubular pipes cut to shape,drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165,complete all as specified and directed 101 S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanksand similar work conforming to Fe.290.Gde-E-165,complete all as specified and directed 102 Excavating in post holes each n.exc 0.5 cum, in soft / loose soil ,getting outand removing surplus soil to a distance n.exc 50 m and making good surface,complete all as specified and directed 103 M & L forplaincement concrete1:3:6 type C-2 using (40 mm graded crushed stone aggregate) as infoundation post/strutetc ,complete all as specified and directed 104 Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. Laid bedded in any mortar,complete all as specified and directed 105 M&L 20mm thick granite (of any type) on vertical surfacesmachine cut, bedded and jointed with grey cement slurry and pointed with white cement with admisxture of pigment to match the shade of granite stone including grinding, polishingcomplete over and including 10mm thick plaster in cement mortor 1:3 ,complete all as specified and directed 106 M&L Dholpur stone with hammer dressed in vertical/ circular facework (with maximum depression from a straight edge held against the dressed surface not exc 20mm), about 40mm high, 75mm deep in straight courses, laid and jointed in cement and stone dust mortar 1:3, recesspointed(10mm x 20mm) with an admixture of white cement and Dholpur stonedust1:1 over and including10mm thick plaster in cement mortor 1:3,complete all as specified and directed 107 M & L for rendering 15mm thick cement plaster in CM (1:4) on brick work or concrete surfaces finished even and fair without using extra,complete all as specified and directed 108 M&L for brickwork with old sized subclass B bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 etc,complete all as specified and directed 109 S&F in repair 2mm thickfibre glass reinforced translucent corrugated/plane sheeting with two corrugated side lap fixed withL type or J typeor cranked hook and washer in wall ,complete all as specified and directed 110 M&L for preparation of old plastered/unplastered wall surfaces by washing down, brooming down , steel wire brushing and removing all grass, vegetation or shrubs from wall and roof etc and applying two coats of cement base paint, complete all as specified and directed. 111 Supply and fixing reflecting sign letter of hight 30-45cms and of web/flange widthup to 10 cm and thickness up to 1 to 2 cm on arches gates of hight up to 6m made of high acrylic sheet by making frame of angle iron all around and raising over black sheet all other specified (Sample to be shown on site), complete all as specified and directed. 112 M&L forpreparation of old paintedsteel & iron surfaces of any description over 10cm width or girth and applying Two coat ofsynthetic enamel paint complete all as specified and directed (Bldg upto & including 3 storey), complete all as specified and directed. 113 M&L for single phasing point wiring system used as copper conductor wire for phase and neutral wiring system the wire made out of PVC insulated FRLS of 1100 volt grade with having multistranded copper conductor wire of size 1.5 Sq.mm (Nominal area) ISI marked drawn through wiring system surface on wall or concealed in wall with the help of heavy duty ISI mark PVC conduit pipe orPVC Casing capping ISI mark in any lengthy wiring system and along with its all connected fittings accessories including providing of suitable sizes of modular boxe and modular plates of suitable way mounting of any type/size switches sockets, regulators etc and including using /drawing of one run of single wire 1.5 sqmm PVC insulated FRLS wire 1100 volt grade ISI marked with multistranded copper conductor wire used as a continuous earth wire for point wiring complete system and including making the good to all disturbed surfaces of wall/ceiling area of new wiring system and to match to it as per the existing surface of wall/ceiling etc, complete all as specified and directed. 114 Description all as per serial item No 113 here-in-before but one light point / fanpoint/bell point wiring system controlled by oneway switch 5 Amp , complete all as specified and directed. 115 Description all as per serial item No 113 here-in-before but one 5 Amp socket outlet point wiring system fixed on independent board & controlled by one way switch, complete all as specified and directed. 116 Description all as per serial item No 113 here-in-before One Ceiling Fan / Wall fan / Exhaust fan point controlled by one, one way switch and regulator, complete all as specified and directed. 117 Description all as per serial item No 113 here-in-beforeOne 3 point 5 Amps switch socket outlet point controlled by one switch on the same board, complete all as specified and directed. 118 Description all as per serial item No 113 here-in-before butusing PVC insulated FRLS wire 1100 volt grade with multistranded copper conductor wire of size 2.5 Sq. mm (Nominal area) ISI Marked for power socket point on indenpent board point wiring systemand also providing of 2.5 sqmm PVC insulated FRLS wire 1100 volt grade ISI Marked with multistranded copper conductorwire used as a continuous earth wire for power point wiring system, complete all as specified and directed. 119 Supply & fixing of modular type switch 5/6 Amps 220 Volts AC,one module, complete all as specified and directed. 120 Supply and fixing of modular type socket of 5/6 Amps 220 Volts AC,3/5 multi pin type with two modular, complete all as specified and directed. 121 Supply and fixing of modular type switch of 15/16 Amps 220 Volts AC one module, complete all as specified and directed. 122 Supply and fixing of modular type socket of 15/16 Amps 220 Volts AC 5/6 multi pin type with two modular, complete all as specified and directed. 123 Supply and fixing ceiling rose three terminals type made out ofpolycarbonate , isolated body, complete all as specified and directed. 124 Supply and fixrecessed/ceiling concealed mounted down lighter lightfitting of round/Square flate shapes decorative type with high efficiency PMMA fiffuser soft glare free light with drivers & LED luminaire of rating capacity in 15 Watt to 18 Watt 220 volt AC complete light fitting set all as per existing fitting type/ size of sample /model and make and including making in cutting or additional extra corner cutting work on existing hole of ceiling surface (when if required at site) for setting & fixing of new light fitting complete including making in additional extra corner cutting work on existing hole of ceiling surface (when if required at site) for setting & fixing of new light fitting complete and also providing of suitable type of flate fexible two/three core cable and making electric connection, complete all as specified and directed. 125 Supply and fixing LED mirror light fitting with high out put diffuuser 2 feet long of 10 Watt220 volt AC decorative type with driver holder and LED lamp with having energy efficient type use in both warm/white type colour complete light fitting set all as per existing fitting type/ size of sample /model and make and including providing of suitable type flate fexible cable for electric connection from ceiling rose to fitting and making electric connection, complete all as specified and directed. 126 Supply and fixing of LED tube lightfitting of 1x 20W/22W 220V AC decorative box type with driver, holder including LED tube light with having energy efficient type use in both warm/white type colourcomplete including providing of suitable type flate fexible cable for electric connection from ceiling rose to fitting, complete all as specified and directed. 127 Supply and fixing of LED street light fitting for buildings of rated capacity 35 Watt 230 volt AC with having LED driver,lamp bracket with impact and corrosion resistant with lense embeded including thermal management in multiple optices complete with IP 65/66 protectiuon suitable for out door type made out of high pressure die cast hosing with heat resistant glass complete including providing of suitable size of dia GI pipe light grade bracket and it to match/setting the new fitting fixture hole attechment system of suitable bracket length upto 1.2 mtr long and make to shape / bendof 120 degree angle including duly fixed alongwith existing pole /bldg wall/ roof with the help of 02 Nos ofMS fixing clamp alongwith nut bolt and including providing of suitable type of flate fexible two/three core cable and makong electric connection, complete all as specified and directed. 128 Supply and fixing of sheet metal enclosure duly powder coated with single pole and neural enclosure with having a two pin and earth plug & top and mounting chanel alongwith one 01 MCB SP 20 Amp and dully fixed surface on wall or concealed in wall and making all necessary electrical connection including taking down of existing DBs a as required at site, complete all as specified and directed. 129 Supply and fixing of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrengment system suitable ofsize/type of distribution board of rating SPN 8 way type 220 volt AC supply systemwith IP protection rating with ISI marked and having neutral and earth link bus bar and mounting base chanel suitable for holding MCBs incommer and s outgoingsystem complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the electric meter and its wiring connection ,complete all as specified and directed 130 Supply and fixing of MCB SPN 40 to 63 Amps with breaking capacity 10KA C Curve series, 220 Volts, 50 Hz AC supply complete and also making suitable size / type of electric wiring connection, complete all as specified and directed. 131 Supply and fixing of MCB SP 40 to 63 Amps with breaking capacity 10KA C Curve series, 220 Volts, 50 Hz AC supply complete and also making suitable size / type of electric wiring connection complete including taking down of old MCB, complete all as specified and directed. 132 Supply and fixing of MCB SP 06 to 32 Amps with breaking capacity 10KA C Curve series, 220 Volts, 50 Hz AC supply complete and also making suitable size / type of electric wiring connection, complete all as specified and directed. 133 S&F star rated ventilating exhaust fan made out of sturdy engineering plastic body complete with louvers and shutter, 250 mm sweep, 230 VoltsAC single phase, 50Hz, 1200 RPM, coper winding including making of suitable type /size of hole on any type of wall and fixing compete with nut, bolt etc and making good distrubed surface of wall/ceiling & finishes to match and providig flate flexible copper wire & making all electricalconnection complete all as specified and directed. 134 Supply, laying and testing ofLT cable XLPE insulated screened, PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty)with aluminium conductor 1100 volt gradecross sectional area of size 10 sqmm 2 core including laid in trenches or fixing on poles or passing through pipes, completeall as specified and directed. 135 Material and labour for sand cushioning with a layer of sand(Locally available river sand) 8cm thick before laying of cable and 15 cm thick after laying of cable in trenches, below and above / around UG cable for cable protection,complete all as specified and directed.Note - Punned thickness shall only be measured and paid. 136 Supply & laying old size sub class B bricks laid flat in trenches over the cable with the length of brickperpendicular to the directionof cable length, adjacent/abutting each other,complete all as specified and directed. 137 S & F Storage type Water heater (Geyser) 5 STAR of Cap 25 Ltrs working on 230 volts AC supply with in and out going water connection pipe (Hot & Cold)fixing arrangement with fastner ,nut bolts and making good the disturbed surface, complete all as specified and directed. 138 S&F galvanised steel tubing, light grade, ISI marked, for protection of under ground cable on pole/wall/under roadpipe 40 mm bore, complete all as specified and directed. 139 M&L for earthing work complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level and connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers of galvanised steel and to be protected by GI pipe 15 mm bore light grade & connected to earth test point/main switch board or main control board and also providing charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soilall as shown in Electrical Plate No 3 of SSR part -I. and also making arrangment of20 mm dia bore galvanised iron pipe (medium grade) for water and making funnel, wire mesh,and also including provision of concrete pit cover framing work in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate with XPM (weight not less than4 Kg/Sqm) and outer frame work of angle iron 25x25x6mm with top concrete pit cover and handle for lifting of cover, complete all as specified and directed.. 140 Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit includingremovalof batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes, complete all as specified and directed. 141 S&F star rated electric ceiling fan 1200mm sweep min air delivery 210 CFM with service value 6.0 BEE norms 5 star rating with bruhless direct current motor (BLDC)of single phase 230 volt AC alongwith blade, down rod, canopy, clamps with reel insulator, electronic regulator & accessories and MS fan hook fixed in ceiling/roof including providig flate flexible copper wire and making all electricalconnection, complete all as specified and directed. 142 S & F in repair Surface mounted decorative wall mounted bracket light fitting with having gold finish fixture with cognac hammered clear glass diffuser suitable for 7.5W LED filament E-27 base including providing of 1XN 9W LED lamp/1NX7.5W LED filament lamp complete light fitting with having bulb holder based adaptor alongwith providing 01 No of 7W/9W LED bulb in required fittinguse in both Warm/White type colour complete set including providing suitable type of flat flexible two/three core cable and making electric connection, complete all as specified and directed. 143 Material and labour for sub main wiring with tworuns of single core FRLS PVC insulated, multistranded unsheathed copper conductor cable of size 6.0 square mm and drawing through PVC conduit of 20mm dia with accessories on concealed in wall/roof along with one run of 6.0 square mm FRLS PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board duly making good the disturbed wall surfaces to match with the surroundings, complete all as specified and directed.Note: 3 runs of 6.0 Square mm cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre. 144 Material and labour for sub main wiring with tworuns of single core FRLS PVC insulated, multistranded unsheathed copper conductor cable of size 16 square mm and drawing through PVC conduit of 20mm dia with accessories on concealed in wall/roof along with one run of 16 square mm FRLS PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board duly making good the disturbed wall surfaces to match with the surroundings, complete all as specified and directed.Note: 3 runs of 16 Square mm cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre. 145 S&F in replacement of twin core flat/ circular cable of size 4 sqmm 1100 Volts grade, heavy duty cable PVC insulated multistranded aluminium conductor cable served with inner sheathed of PVC tap and overall PVC sheathed and making electric connection, complete all as specified and directed. 146 S&F in repair rigid non metallic PVC conduit pipe of size 25 mm borewith all fitting including providing clamping arrangement attachment for holding of pipe on wall inproper size of clamps, nut bolt and washer etc,complete all as specified and directed. 147 S&F in repair rigid non metallic PVC conduit pipe of size 15/20 mm borewith all fitting including providing clamping arrangement attachment for holding of pipe on wall inproper size of clamps, nut bolt and washer etc, complete all as specified and directed. 148 Supplying and fixing in replacement of flexible type round PVC bedded with PVC insulated and sheathed with multi FRLS cable of 1100 volt grade with multistranded copper conductor wire of size 1.5 Sq.mm 3 core type (Nominal area) ISI Marked, complete all as specified and directed. 149 Supply and fixing in repair New generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source 25W, 5700K forfixing at gates with PCC work and GI pipe of suitable size including finishing of disturb surface, complete all as specified and directed. 150 Notes :-An amount of Rs 96948.00 on account of Credit Schedule for Schedule A Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.
