|
| 1 | Earth work in excavation by mechnical means(Hydraulic excavator) /manual means in foundation trenches or drain(not exceeding 1.5 m in width or 10.0 sqm on plan including dressing of sides and ramming of bottoms, lift upto 1.5 m,including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kind of soil. |
| 2 | Brick work with common brunt clay F.P.S (non modular) bricks of class designation -7.5 in superstructure above plinth level in all shapes and sizes with cement mortar 1:4 (1 cement : 4 coarse sand)as per the direction of Engineer-In-Charge . |
| 3 | Centering & shuttering including strutting, propping etc, and removal of from work for Retaining wall, return walls, walls(any thickness) in cluding attached pilasters, buttresses, plinth and string courses fillets,kerbs and steps. |
| 4 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 5 | Providing & Laying Vitrified floor tileswith water absorption\"s less than 0.08%and conforming to IS : 15622 of approved make in all colours and shades , laid on 20mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement & matching pigments etc., complete. |
| 6 | Providing & fixing Kota stone flooring over 20 mm(average)thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) 25 mm thick. |
| 7 | 15 mm th. Cement plaster 1:4 (1 cement : 4 sand)on brick work completion with all respect and as per the direction of Engineer-in Charge. |
| 8 | Steel work in built up tublar (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a primery coat of approved steel primer, including elding and bolted with special shaped washers etc complete. Hot finished welded type tubes. |
| 9 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 1.0 KM lead as per direction of Engineer - in- charge. |
| 10 | R.R.Stone masonry 1:6 cement mortar (1 part cement & 6 part sand) including all materials, labours& T&P,as per the direction of Engineer-in Charge. |
| 11 | Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade. |
| 12 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works. |
| 13 | Applying priming coat,With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood). |
| 14 | Painting with synthetic enamel paint of approved brand and manufacturar to give an even shade - two or more coats on new works. |
| 15 | Providingandfixingaluminiumworkfordoors,windows,ventilatorsand partitionswithextrudedbuiltupstandardtubularsections/appropriateZ sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight,mitredandjointedmechanicallywhereverrequiredincludingcleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing,panelinganddashfasteners tobepaidfor separately). |
| 16 | Providingandfixingglazinginaluminiumdoor,window,ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item)-With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm). |
| 17 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates withbrasspivotandsinglepieceM.S.sheetouterboxwithslideplateetc. complete as per the direction of Engineer-in-charge. |
| 18 | Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 19 | Providing and fixing aluminium tower bolts, ISI marked, anodised-200x10mm (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete . |
| 20 | Providing and fixing chromium plated brass handles with necessary screws (125 mm) etc. complete. |
| 21 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm. |
| 22 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 23 | Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type). |
| 24 | Providing and fixing stainless steel (grade 304) railing/gate made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature(where required) and fitting the same with necessary sainless steel nuts and bolts complete i/c fixing the railing necessary accessaries & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or side of waist slab sutaible arrangement as per approval of engineer-in-charge. |
| 25 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required, W.C. pan with ISI marked white solid plastic seat and lid. |
| 26 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively withautomaticflushingcisternwithstandardflushpipeandC.P.brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. |
| 27 | Providing and fixing wash basin (630x450 mm size)with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. |
| 28 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 29 | ProvidingandfixingC.P.brasslongbodybibcockofapprovedquality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore. |
| 30 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length. |
| 31 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape (size 453x357 mm). |
| 32 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with Total = length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms. |
| 33 | ProvidingandfixingChlorinatedPolyvinylChloride(CPVC)pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (for internal /external works) |
| 34 | 15 mm nominal inner dia Pipes. |
| 35 | 20 mm nominal inner dia Pipes. |
| 36 | 50 mm nominal inner dia Pipes . |
| 37 | 80 mm nominal inner dia Pipes . |
| 38 | 100 mm nominal inner dia Pipes. |
| 39 | Providing corrugated G.C.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.80 mm thick with zinc coating not less than 275 gm/m². |
| 40 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak three ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick Fixing with hinges of required size and necessary screws. |
| 41 | Supplying and fixing 10 Gauge weld mesh of size 100mm x100 mm for floor/ roof slab concrete screed over the micro beams as reinforcement. The weld mesh shall be fixed as per drawing. |
| 42 | Providing & laying in position cement concrete of specified grade excluding the cost of centring & shuttering 1:2:4(1 cement: 2 coarse sand : 4 graded stone agregate 20 mm nomonal size). |
| 43 | Providing & laying in position cement concrete of specified grade excluding the cost of centring & shuttering 1:1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone agregate 20 mm nomonal size). |
| 44 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.12.4.1 0.80 mm thick with zinc coating not less than 275 gm/m |
| 45 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore. |
| 46 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 47 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 48 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) Size 300x16mm. |
| 49 | Supply & Fixing of self supporting insulated partition wall work consisting of insulated panels made out of 0.5mm TCT off-white colour coated - SMP internal & external plain liner steel sheet sandwich in between 150mm thick insulation material having male female type fixing arrangement for supporting the panels to each other with necessary angle flashing arrangement complete. |
| 50 | Supply, Design, Engineering, Fabrication and installation of STP (Sewage Treatment Plant) MBR technology at near old Batching Plant for Shift duty of CISF Securties personnel at KHEP, Koteshwar. |
