Tender For Special Repair Of Bldg No Al 50 And Al 51 (Jcos Md Accn) At Dagshai Under Ge Kasauli; 2 Demolition of brick or stone masonary built in cement mortar including all quoins arches pillars upto 10 mtr height as in roof chimney, walls , manholes, chambers and similar work etc including precast concrete block complete all as specified and as directed. 3 Material and labourbrick work with sub class B old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge. 4 Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern as in roof coverings complete all as specified and as directed. 5 Dismantling timber scantling 40 sq.cm and over in section in any position upto 10mtr height in framed or unframed work etc complete all as specified and as directed. 6 Supply and fixingsecond class hard wood over 40 sqcm in section as in roof trusses, members, scantling, or in other position upto 10metre height, etc. timber framed and clean sawn, complete all as specified and as directed. 7 Supply and fixing mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal/ square nut or Mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised of any size and length as per site requirement, etc. complete all as specified and directed. 8 Material and labour for cement concrete 1:2:4 type B1 (using 20mm graded aggregate) as in copings, roof kerbs or mud stops, rounded or chamfered on edges, cills, steps,hold fast,filing gaps/spaces between wooden/ mild steel member embedded in stone / brick masonry wall etc complete all as specified and directed. 9 Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.60mm thick conforming to IS-15961 of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws on wooden trusses in any position or slope upto any heightcomplete all as specified and directed.Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965. Contractor shall submit a Purchase voucher and manufacturer test certificate to Engineer-in-Charge before claiming payment. 10 Supply and fixing plain mild steel sheeting 0.60 mm thick, in rain water gutters, drip and straight flashings (length and girth as fixed ), ridges, hips, and similar work etcfixed as welded or solderedjoints, reveting are providedetccomplete all as specified and directed.Note : i)Rates are included for providing nozzles, stop ends, drop ends made of mild steel sheeting 0.60mm thick with necessary fixing arrangement/ jointing with rubber sealant for PVC downwater pipes.ii)The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965. Contractor shall submit a Purchase voucher and manufacturer test certificate to Engineer-in-Charge before claiming payment. 11 Material and labour for mild steel works for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, hook and pintle hinges: clamps; hold fasts; wall ties; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. 12 Supply and fixing in repairs 40 mm, 2nd class hard wood wrought treads without rounded nosings, with 25 mm wrought risers on tongued both edges, glued, wedged and blocked complete all as specified and as directed.(Note : Rates are included for necessary cutting/rebating to ends of treads for fixing MS nosing to level flush with treads (width and depth of rebating or cutting as per size of mild steel nosing) 13 Supply and fixing in repairs 40mm thick 2nd class hardwood boarding as in floors, planed one side, with butt joints and fixed with screws, etc.to the existing floors in patches, including cutting out, piecing, heading joints, etc complete all as specified and as directed. 14 Material and labour for 9mm thick (5ply) plywood, , grade BWR, type BB, fixed with screws to timber frame work or over existing wooden planks flooring complete all as specified and directed.Note : Rates are included for preparation of existing wooden planks flooring surface plane, smooth and free from any overhead nails or screws etc and filling the uneven surfaces, depressions, holes on existing wooden planks flooring with mixture of sawdust and wood glue before fixing of plywood. Note- Contractor shall submit a Purchase voucher and manufacturer test certificate to Engineer-in-Charge before claiming payment. 15 Material and labour for PVC tiles / sheets 1.50 mm thick laminated plaincoloured, marbled mosaic or mottled finish, laid with approved rubber based /synthetic adhesive or as per manufacturers instructions etc for fixing over wooden planks flooring complete all as specified and as directed.Note- Contractor shall submit a Purchase voucher and manufacturer test certificate to Engineer-in-Charge before claiming payment. 16 Dismantling boarding any description, fixed in any position with nails or screws, etc. including fillets complete all as specified and as directed. 17 Material and labour for 6 mm thick (5ply) plywood, plywood, grade BWR, type BB fixed with screws to timber frame work or over existing wooden planks flooring complete all as specified and directed. 18 Dismantling timber scantling 40 sq.cm and underin section in any position in framed work as in fillets, rails, posts, rafters, purlins, etc. complete all as specified and as directed. 19 Material and labour for Second class hardwood (Hollack) plain fillets, square, rectangular or triangular in section of area exceeding 13 Sq. cm and not exceeding 25 Sq. cm, clean sawn, fixed straight or curved, secured with nails or brads, etc. complete all as specified and as directed. 20 Supply and fixing for mild steel section framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, window guard bars, and fixed independently in wooden frames including fixing mild steel screws, supports for shelves, sinks, etc and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 21 Supply and fixing hard drawn steel wire fabric, weight n.exc 4 kg/Sqm, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement etc complete all as specified and as directed. 22 Supply and fixing for mild steel Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete or wood and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, welding etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 23 Demolition ofcement concrete in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and directed. 24 Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work , and removal the rubbish/ demolished material outside defence land, complete all as specified and directed. 25 Material and Labour for form work chulla hoods, chajjas, troughs and similar items including edges for fair finished surface of concrete, complete all as specified. 26 Material and Labour for formwork to sides and soffits of roof beams, cantilever, bressummers ,lintels , shelves including supports and similar work for rough finished flat surfaces of concrete, complete all as specified. 27 Material and labour for reinforced concrete nominal mix (1:1.5:3) (using 20mm graded stone aggregates) as in chajjas,in beams, cantilevers, lintels over 1.50m span, shelves, etc.complete all as specified and directed. 28 Material andlabour TMT bars, 10 mm dia and above , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm diaor securing with clips, complete all as specified and directed. 29 Material andlabour TMT bars, 6mm to 8mm dia , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm diaor securing with clips, complete all as specified and directed. 30 Taking down cement plaster of any description, thickness, in any position and height from brick or stone wall or concrete surface, etc.including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. 31 Material andlabour for 10mm thick rendering in cement mortar (1:6)on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified. 32 Material andLabour for 15mm thick rendering on surface of any description of brick work, concrete surfaces in cement mortar 1:4and finished the surface even and smooth without using extra cement mixed with @ 200 ml WPC (liquid type) per bag of cement or as per manufacturer’s instructionscomplete all as specified and directed.Note:-WPC (liquid type) shall be measured and paid separately as supply only. 33 Material and labour 20mm thick rendering in cement mortar (1:6) on other than fair faces of stone masonary, brick or concrete surface and finished the surface even and smooth without using extra cement complete all as specified. 34 Material and labour 20mm thick rendering in cement mortar (1:4) on other than fair faces of stone masonary, brick or concrete surface and finished the surface even and smooth without using extra cement mixed with @ 200 ml WPC (liquid type) per bag of cement or as per manufacturer’s instructions complete all as specified and directed.Note:-WPC (liquid type) shall be measured and paid separately as supply only. 35 Taking down loose plaster from ceiling of slab, edges and soffit of chajjas and the like, cleaning surface with wire brush to remove all dust/dirt/loose particles to expose old steel reinforcement,cleaning of old reinforcement and applying neat cement slurry@ 3Kg per sqmand 30mm thick (in two layers , each layer 15mm thick) plaster in cement mortar 1:3 mixed with @ 200 ml WPC (liquid type) per bag of cement not exc 3 sqm each patchincluding removal of rubbish/demolished material to a distance exceeding 250mtr and not exc 500mtr , including provsion of scaffolding up to 10m height required for repairing work and applying three coats of white lime wash complete all as specified and as directedNote:-WPC (liquid type) shall be measured and paid separately as supply only. 36 Supply only liquid water proofing compound of approved make all as specified and directed. 37 Material and labour providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternatebays (not exc 2 Sqm each )and finished even and smooth without using extra cement and providing jointsthroughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work complete all as specified and as directed. 38 Taking down wooden chowkats or frames areanot exceeding 1.50 Square metre(w/o taking off shutters from frames) including iron mongries and removing from site, including cutting holes for taking out existing hold fastsand making good the disturbed portion of jambs andadjoining surfaces to match with existing finish, complete all as specified and as directed. 39 Taking down wooden chowkats or frames area exceeding 1.50 Square metre andnot exceeding 4.00 Square metre (w/o taking off shutters from frames) including iron mongries and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfaces to match with existing finish, complete all as specified and as directed. 40 Taking down shutters of any description but not exceeding 1.00 Sq.m eachfrom chowkhatincluding iron mongries and removing from site complete all as specified. 41 Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each, from chowkhatincluding iron mongries and removing from site complete all as specified. 42 Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each, from chowkhat and refixing in the same opening after making nessary repair and make the shutter in working condition, etc. complete all as specified and directed.(Note : The quoted rates are included for filling of cracks or holes with wood filler, wood glue and saw dust or wood plugs for smooth and even surfaces) 43 Material and labour 2nd class hardwood as in plain, solid straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed 44 Supply and fixing 40 mm thick factory made Flush shutters (double/single leaf), solid core construction, with particle board core and with0.9 mm thick decorative laminates, type I, commercial type on both sides, colour and pattern as approved with adhesive etc complete all as specified and directed. 45 Supply and fixing 35 mm thick, 2nd class hard wood, partly or fully glazed and skelton shutter open rebatedand prepared to receive glass ,gauge etcdivided into squares with plain, chamfered or rounded, mitred beads, rebated sash bars any numbers for securing glass, etc or partly with panels of 9mm BWP commercial ply etc with size of members of shutters as specified in SSR Part-I, section 8 clause 8.24(a) or to match with existing shutters etc complete all as specified and as directed. 46 Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed.(Note: Stainless steel butt hinges and necessary S.S screws shall be paid separately). 47 Material and labour in repairs for 2nd class hardwood as in small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles(including screws, nails, hinges etc to fix with door or window frame)n exc 200 cu.cm each complete all as specified and as directed 48 Supply and fixing aluminium power coating of approved colour (Thickness or powder coating not less than 50 micron) frame for doors, windows, ventilators, partitions incl necessary joining cleats, rubber packing, snap beading, glazing clips for fixing glass etc with one or more rebates or double/ triple track channels for sliding shutter windowsincluding joining cleatand steel screw for fixing frame to walls/jambs etc. completeall as specified and directed. 49 Supply and fixingpowder coated aluminium anodised window(Three track sliding window, 02 shutters with glass and 01 shutter with wiremesh) made out hollow aluminium as mentioned below. Each shutter shall have 01 No. aluminium handle of 75mm size and 02 Nos self locking device. Window shall be glazed with 4.00mm thick tinted glass fixed with glazing clips, rubber beading and anodized aluminium beading and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or stainless steel wire staple etc complete all as specified and as directed. Chowkhat bottom section size : 50.3mm X 26.0mm, 1.20mm thickChowkhat top & sides section size : 50.3mm X 15.0mm, 1.00mm thickShutter top & bottom rail section size : 101.60mm X 44.45mm, 1.50mm thickShutter inner lock rail section size : 37.5mm x 15.0mm, 1.50mm thickShutter side mid rail section size : 37.5mm x 15.0mm, 1.36mm thickNote :- (i) The weight of Aluminium sectons shall not be less than 0.55Kg/RM. (ii) Minimum thickness of anodization shall be 15 micron. (iii) The door/window shall be as per drawings/directions of Engineer-in-charge and drawing may be reffered from GE office.NOTE: (Glass and wire mesh shall be paid seperately). 50 Supply and fixing aluminium power coating of approved colour (Thickness or powder coating not less than 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws etc. complete all as specified 51 Supply and fixing9mm thick pre-laminated particle board, exterior grade, both sidelaminations of approved colour and pattern, fixed to wooden/aluminium frame work as in partitions, doors, etc. including necssary fittings, etc. complete all as specified and as directed. 52 Supply andfixing mild steel butt hinge of 100mm length, cold rolled, medium weight, ISI marked complete all as specified and directed. 53 Supply and fixing mild steel, semi-barrel tower bolt 200 mm , open cover, with sheet pressed barrel, stove enamelled black with bright bolt complete all as specified and as directed. 54 Supply and fixing 150mm long mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed. 55 Supply andfixing 200 mmmild steel sliding door bolt, ISI marked, stove enameled black, with bright bolt not less than 12mm diawith and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple, complete all as specified and directed. 56 Supply andfixing300 mmmild steel sliding door bolt, ISI marked, stove enameled black, with bright bolt not less than 16mm diawith and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple, complete all as specified and directed. 57 Supply and fixing for floor door stopper of aluminium alloy body and tongue , anodised with hard drawn steel spring over all length of cover plate 150mm complete all as specified and directed. 58 Supply and fixing 4.80 mm thick Sheet glass, ordinary quality and glazing with oil putty or fixing in aluminium shutters/frames in any shape and size complete all as specified and as directed. 59 Supply and fixing 4.80 mm thick obscured or frosted glass, ordinary quality and glazing with oil putty or fixing in aluminium shutters/frames in any shape and size complete all as specified and as directed. 60 Supply and fixing 2 to 3mm thick plain/textured flexible crystal clear/frosted, polycarbonate, plain sheets, including cutting to required shape and size as in openings of terraces, balconies, verandahs, windows and similar work, fixed on timber frame or MS frames with self driving screwsetc complete all as specified and directed 61 Supply and fixing stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed 62 Supply and fixing for 18mm/19mm thick plywood, grade BWP, type BB with 0.9mm thick decorative choice lamination on both sides of approved colour and pattern fixed with screws, solvent cement/ adhesive to make shelves (including fixing on timber supports with nails or screws), etc. and similar work etc complete all as specified and as directed.(NOTE:- Rates are includusive of fixing shelves with sufficient nos of wall plugs, screws, brackets, toggle bolts, handles, magnetic catcher, PVC edge strips etc) 63 Material and labour for applying 2 mm thick wall care putty on walls in two layers of 1mm thick each layer and sanding with sandpaper to remove any loose particles, unevenness, wrinkles to achieve a smooth and even surface, etc. complete all as specified and as directed. 64 Material and labour for preparation ofnewly plastered surfaces of walls and applying two coat ofoil bound distemper over a coat of Chalk whitening, etc. complete all as specified and as directed. 65 Material and labour for preparation of oldplastered surfaces of wall by complete removal of existing treatment with mechanical scrapper including washing, rubbing down dust and loose particles and applying two coat ofoil bound distemper, complete all as specified and as directed. 66 Material and labour for preparation ofnewly plastered surfaces of walls and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.etc complete all as specified and as directed. 67 Material and labour for preparation of oldplastered surfaces of wall by complete removal of existing treatment with mechanical scrapper and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.etc complete all as specified and as directed. 68 Material and labour for preparation of new steel surfaces of any description over 10cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a coat ofred oxide primer complete all as specified and as directed. 69 Material and Labourfor preparation of new steel surfaces of any description not otherwise described,not exceeding 10 cm width or girth when unconnected with other painting or when painted in a different tint and applyingtwo coats of synthetic enamel paint on steel surfaces over a coat of red oxide primer , complete all as specified. 70 Material and labour for preparing new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified. 71 Material and labour for preparation of new wooden surfaces of any description not exceeding 10cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a coat ofpink primer, etc. complete all as specified and as directed. 72 Material and labour for preparation of old painted wooden surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed. 73 Demolition of stone slab and tilesof any description or thickness in floors aprons etc laid bedded and pointed in any mortaretc complete all as specified and as directed. 74 Material and labour for machine cut kota stone slab 18-22 mm thick (of size not less than (55 cm x 55 cm) laid in glooring and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting waste, rubbing and polishing (Granite finish) over and including cement screed bed 20mm thick in cement mortar (1:4) base , complete all as specified. 75 Material and labour for machine cut kota stone slab 16-18 mm thick laid on verticle surface and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in skirting over and including 10mm thick plaster in cement mortar (1:3) onbrick work or concrete surfaces, complete all as specified. 76 Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 77 Material and labour for premium quality, glazed coloured ceramic tiles 300 x 450 x 7mm thick on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match ,complete all as specified. 78 Material andlabour for premium quality, joint free, non skid, coloured ceramic 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm tiles, as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and includingcement screed bed 15mm thick in cement mortar (1:4) base, complete all as specified. 79 Material andLabour for Premium quality, vitrified ceramic tiles, light shade, 7 to 8mm thick (square/rectangular) area of each tiles not exceeding 0.36 sqm , as in floor, set and jointed in neat cement slurry @ 3.00 kg/Square metre and pointed in white or coloured cement to match the surface over and includingcement screed bed 15mm thick in cement mortar (1:4) base complete, all as specified. 80 Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store complete all as specified and directed . 81 Supply and fixing of 15mm dia tubes, medium grade, galvanized, ISI Marked, with all fittings such as sockets, bends, elbows, tees etc, fixed to walls and ceiling or laid in floors, including cutting existing steel tubing and screwing, if required for alterations and additions, complete all as specified and directed. 82 Cuttingchases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed. 83 Supply and fixingin repair, 75mm diaUPVC, soil waste drain pipe, type ‘B’ ,conforming toIS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified anddirected.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985) 84 Supply and fixingin repair, 75mm diaUPVC, soil waste drain pipe, type ‘B’ ,conforming toIS 13592-1992, double socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified anddirected.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985) 85 Supply and fixingin repair, 110mm diaUPVC, soil waste drain pipe, type ‘B’ ,conforming toIS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified anddirected.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985) 86 Supply and fixingin repair, 110mm diaUPVC, soil waste drain pipe, type ‘B’ ,conforming toIS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified anddirected.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985) 87 Supply and fixingin repair, 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified.(Note- UPVCbends shall be confirm to BS 4515 DIN 19531 and DIN 19534) 88 Supply and fixingin repair, 75 mm bore UPVC (SWR) bend with access door including jointing with solvent cement, complete all as specified.(Note- UPVCbends shall be confirm to BS 4515 DIN 19531 and DIN 19534) 89 Supply and fixingin repair,110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified. (Note- UPVCbends shall be confirm to BS 4515 DIN 19531 and DIN 19534) 90 Supply and fixingin repair,110 mm bore UPVC (SWR) bend with access door including jointing with solvent cement, complete all as specified. (Note- UPVCbends shall be confirm to BS 4515 DIN 19531 and DIN 19534) 91 Supply and fixing in repairs 75mm dia junction single (Single T) equal or unequal and jointing etc complete all as specified and directed. 92 Supply and fixing in repairs 110mm dia junction double (Double T) equal or unequal and jointing etc complete all as specified and directed. 93 Supply and fixing in repairs 110mm dia PVC(SWR), vent cowl complete all as specified and as directed. 94 Supply and fixing in repair 75 mm dia PVC(SWR) floor/ nahani trap, with CP grating including jointing with solvent cement, complete all as specified and as directed. 95 Supply and fixing in repair 110 mm dia, PVC(SWR), P trap including jointing with solvent cement, complete all as specified and as directed. 96 Supply and fixing in repair, bib tap, long body, screwed down, high pressure, cast copper alloy, fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union complete all as specified and directed.Make- PRIMA Cat No PFL-6202 or equivalent model in makes mentioned in Appendix B of tender document.Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. 97 Supply andfixed as in repair, for cast copper alloy, chromium platedlong body, wall mixer for mixing hot and cold water,capstan heads, screwed down high pressure with long screwed shank and fly nuts, fancy type screwedfor iron pipes and fixed bore of pipe 15mm ,complete all as specified.Make- PRIMA Cat NoPFL-6214or equivalent model in makes mentioned in Appendix B of tender document.Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. 98 Supply and fixing in repairs sinks with drainage board made of stainless steel1 mm thick kitchen or laboratory overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmwith plugs, washers, waste coupling and PVC waste pipe ; including bedding in cement mortar to dwarf wall or fixing cantilever brackets and connecting union to pipe etc complete all as specified and directed. 99 Supply and fixing in repair, angle cock, 15mm dia, cast copper alloy, chromium plated, ISI marked, screwed down, high pressure with capstain head, screwed both ends for iron pipes or for unions complete all as specified and as directed.Make-Prima Art No- PFL-6205 or equivalent model in makes mentioned in Appendix B of tender document .Note: Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. 100 S & Fvitreous china wash hand basin white, flat back of size 630mmx450mm with pedestal fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing ofwaste fitting etc complete all as specified and as directed by the Engineer-in-Charge. 101 Supply and fixed (in repair), vitreous china wash down water closet pedestal pattern, white including connection to trap and to flushing pipe with ‘P’ or ‘S’ trap,plastic water closet seat cover with mild steel chromium plated hingesand chromium plated jet spray suitable for EWC with 1.5 meter flexible LDPE pipe jointed with pipe complete all as specified.. 102 Supply and fixing in repair ofvirgin polypropylene cistern, 10 litre capacity, ISI marked, coloured, low level complete with PVC bend/flush pipe and making all connectionsincluding taking down existing high or low level unserviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified and directed. 103 Supply and fixing in repairhealth faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in positioncomplete all as specified and as directed. 104 Material and labour for 18-20 mm thick Granite (of any type) work ( table rubbed and polished) in steps, jambs, window cills, cooking platform, wash hand basin , urinal partition etc and like fixed to wall in verticle position laid over 10 mm thick rendering/screed bed in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite to match the shade of the slab and rounding of edges complete all as specified and directed. 105 Supply and fixing of grating doom 100 mm dia with waste hole of stainless steel complete all as specified and directed. 106 Supply and fixing in repair, PVC connections 450mm long with PTMT nuts and PVC washers on both ends fixed to 15 mm bore of pipe complete all as specified and directed. 107 Supply and fixing in repair, looking mirror of size 450mmx600mm and 5.5mm thick, selected quality, bevelled edges, glass mounted on 6mm thick AC building board with aluminiumbeadingandrubber packing and fixed to wall with wooden plug with chromium plated brass screws and cup washers complete all as specified anddirected. 108 Supply and fixing, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. 109 Supply and fixing of brass chromium plated tubular towel rail (finish Glossy), 20mm dia, D type, 60cm long between flanges complete all as specified and directed.Make- PRIMA Cat No PDX -4501 A or ESSCO Cat No-1111 or Prayag Cat No. BA-20 orequivalent model in makes mentioned in Appendix B of tender document.Note- Contractor shall submit a guarentee certificate for tubular towel rail from manufacturer to Engineer-in-Charge before claiming payment. 110 Supply and fixing Soap dish fixed to plugs with chromium plated brass screws etc complete all as specified and as directed. 111 Supply and fixing in repair decorative stainless steelof approved quality curtain rod 25mm dia having wall thickness 1.60 mm with and including decorative stainless steel brackets ,stop roller at the end/ finialsetc, fixed with stainless steel screwscomplete all as specified and as directed . 112 Supply andfixing decorative stainless steel 100mm long and fixed with stainless steel screwscomplete all as specified and directed. 113 Material and labour for taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing materials to store for keeping in safe custody for re-use at site and making good disturbed surfaces of walls floors, etc., complete all as specified and as directed by the Engineer-in-Charge 114 Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cableFRLS-H, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, on wall/ceilingand incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cableFRLS-H, 1100 volt grade with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally including provision of new 3 mm thick plastic laminated sheet top cover extended up to 25 mm over sunken box for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washersand making goodthe disturbed surfaces as per existing for one light/fan point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately . PVC Conduit confirming to IS 9537 part I & III . 115 Description same all as per item No. 113.00 but for One 3 pin, 5 Amps, socket outlet controlled by one switch on independent board,complete all as specified and as directedby Engineer-in-Charge. 116 Description same allas per item No. 113.00 but for One 3 pin 5 Amps socket outlet controlled by one switch on Same board,complete all as specified and as directedby Engineer-in-Charge. 117 Description same all as per srl item No 113.00 here-in-before but for one socket outlet 15 Amp with 4.00 sq mm PVC insulated, unsheathedcable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copperwire as earth continuity conductor connected to common earth dolly complete all as specified and as directed. 118 Taking down carefully unserviceable Sub main wiring of any size and type, removing material from site for taking credit and making good the disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as specified and directed 119 Material and labour for sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade, ISI marked with multi stranded copper conductor and one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuity conductor connected to common earth dolly including concealed on wall/ceiling surfaces in PVC conduit medium gradeISI marked of adequate size for housing the wires complete all as specified and as directed.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. 120 Material and labour for sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade, ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuity conductor connected to common earth dolly including concealed on wall/ceiling surfaces in PVC conduit medium gradeISI marked of adequate size for housing the wires complete all as specified and as directed.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. 121 Supply and fix modular switch 1 module, single pole, one way 6 Amps flush type, 230 voltscomplete all as specified and as directed. 122 Supply and fix modular switch 1 module, single pole, one way 16 Amps flush type, 230 voltscomplete all as specified and as directed. 123 Supply& fixmodular socket outlet2/3 pin combined,6 Amp, one way, two module, 230 voltscomplete all as specified and as directed. 124 Supply& fixmodular socket outlet3/3 pin combined, (6pin), 6/16 Amp, one way, two module, 230 voltscomplete all as specified and as directed. 125 Supply and fixing modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and as directed. 126 Supply and fixing Ceiling rose surface bakelite 65x50mm three terminals including provn ofPVCblocks, complete all as specified and as directed. 127 Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directed. 128 Supply and fixing for Bell, electric,Ding DongAC, 230 volts, single pole fixed in repair complete all as specified and directed. 129 Supply and fixing in repair surface mounted LED fitting 18W, 220 V, AC, in extruded aluminium with driver, including LED tube light including all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed. 130 Supply and fixing in repair surface mounted LED fitting 10W, 220 V, AC, in extruded aluminium with driver, including LED tube light including all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed. 131 Supply and fixing in repairs of 9/10 W LED bulk head luminairies incl LED light with clear prismatic diffuser,driver holder connecting up with three core flexible copper conductor cable of suitable sizeincluding all acessories for fixing on wall all as specified and directed. 132 Supply and fixing self ballasted LED Retrofit Bulb 5 Star Bulbs 12 Watt with PBT body shell and PC diffuser. 210 digree wide distruction CCT 6500K, B-22 cap, (Pin type), 230V, PF-0.95 (min) complete all as specified and as directed. 133 Taking down carefully unserviceable distribution board of any capacity including wooden board and making good the disturbed surfaces of walls, etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed . 134 Supply and fixing sheet metal enclosures for distribution boardfor MCBs Load line TPN, 4 ways,double door, 415 volts, with and including 200 amps rated bus bar, vertical type IP 42, with MCCB as incomer andMCBs as out going and making all type of connections with suitable size of gland for incomer LT cable complete , concealed on the wall surface, making good the disturbed portion withadjoining surfaces to match with existing finish complete all as specified and as directed. 135 Supply and fixing sheet metal MCB DB, SPN, 8 way with 200 Amps rated bus bar single pole and neutral withdouble door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed. 136 Supply and fixing in repair, MCCB, 4 Pole, 415 volts, 100 Amps, 16 kA rupturing capacityand making connections complete all as specified and as directed. 137 Supply and fixing in repair MCB,Single Pole and neutral, AC supply, 240 volts,40 Amps,C series,10 kA rupturing capacityand making connections complete all as specified and as directed. 138 Supply and fixing in repair MCB, SP, AC, 240 volts B curve capacity of 06 to 32 Amps, 10kA and making connections with suitable thimble complete all as specified and as directed. 139 Material and labour for plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as inhardstanding, finishing cement concrete surface even and smooth with out using extra cement complete laid in alternate bays including demolition ofcement concrete in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and directed. 140 Supply andfixing in repair, single pole enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA B curvecomplete all as specified and as directed. 141 Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.andincluding taking down unserviceable and deposit to E/M Store. Note:- Geyser will be fitted with fastners-04 Nos including bolts washers etc and making good disturbed surface complete all as specified and directed by Engr-in-Charge. 142 Supply and fixing in replacement exhaust fan AC single phase 230/240 volt of size 300 mm sweep plastic body with louver and connecting with twin twisted copper conductor flexible of size 0.50 sqmmfixing nut bolts necessary for fixing exhaust fan complete all as specified and as directed. 143 Taking down old unserviceable earthing after disconnecting the existing earthing and making good to the existing surface complete all as specified and as directed. 144 Material andlabour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earthwire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test pointas directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/cboth ways with one handle for liftingmade out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete complete all as specified and as directed. 145 Dismantling and taking down old unserviceable underground cable of any size and description from trenches/pole/duct/LT panel after disconnecting from OH conductors and renove the same from sitecomplete all as specified and as directed. 146 Excavating in trenches, not exceeding 1.50 metre wide and not exceeding 1.50m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10 sq.m on plan and not exceeding 1.50m in depth and getting out in hard/dense soil complete, all as specified and as directed. 147 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soil of any description, complete all as specified and as directed.. 148 Removing excavated soil to a distance not exceeding 50 metre and deposited where directed at a level not exceeding 1.5m above the starting point, complete all as specified and as directed. 149 Supply & laying or fixing or passing through pipe, 1100 volts grade, XLPE insulated aluminium armoured heavy duty electric cable with aluminium conductor cross sectional area 16 Sqmm, 3.5 core with suitable glands and lugs,confirming to IS, complete all as specified and as directed. 150 Supplying & fixing in replacementof double walled corrugated HDPE duct pipe of 50 mm outer dia confirming to IS-14930 (Part-II) of approved colour with fittinggs for cable protection complete all as specified and directed. 151 Amount of credit of Rs. 198160.00 for retrived old material as mentioned in Schedule A section-II of tender document in pdf form, will be deducted offline while acceptence of tender.
