construction Of Various Civil Work At Open Space Near H/O Shri Lichade Dandekar Layout Dabha In Prabhag No. 12- 1 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50m.beyond the building area and stacking and spreading as directed,dewatering,preparing th ebed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. By Mechanical Means(Spec. No. : Bd.A. 1 Page 259/CSR I Page No. 148) 2 Excavation for road way in earth,soil of all sorts,sand,gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materialswithallliftsuptoaleadof50m.andspreadingforembankmentorstackingasdirected. 3 Providing selected hard murum filling including laying in layers of 15 to 20cmwith watering and compacting etc. complete. 4 Providing soling using80mm sizetrapmetalin15cm.layerincludingfilling voidswith Crushed sand/grit, ramming, watering etc. complete. 5 Providing and laying Castinsitu/Ready Mix cement concrete inM-10oftrap/granite/ quartzite/gneiss metal for foundation and bedding including bailing out water,Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided,finishing if required and curing complete,with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade) 6 Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material 7 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters forR.C.C.pilecaps,footings,foundations,slabs,beamscolumns,canopies,staircase,newels, chajjas,lintelspardis,copings,fins,archesetc.asperdetaileddesigns,drawingsand schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. 8 Providing and laying in situ /Ready Mixcement concreteM-20of trap / granite /quartzite/ gneiss metalforR.C.C.work infoundationslikeraft,stripfoundations,grillageand footingsofR.C.C.columnsandsteelstanchions etc.includingbailingoutwater, Steel centeringformwork,laying/pumpingcoverblocks,compactionandcuring roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 9 ProvidingandlayingCastinsitu/ReadyMixcementconcreteM-20oftrap/granite/quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 10 ProvidingandlayingCastinsitu/ReadyMixcementconcreteM-20oftrap/granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or asdirectedincludingsteelcentering,formwork,coverblocks,laying/pumping, compactionandrougheningthesurfaceifspecialfinishistobeprovidedandcuringetc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 11 Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructureincludingstrikingjoints,rakingoutjoints,wateringandscaffoldingetc. Complete 12 Providing andlaying Castinsitu/ReadyMixcement concrete M-15oftrap/ granite/quartzite/gneissmetalforcoping to plinthorparapet,mouldedorchamferedasper drawingorasdirectedincludingsteelcentering,plywood/steelformworkcompacting, rougheningthemifspecialfinishistobeprovided,finishingunevenandhoneycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade) 13 Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/Square Metre asperdrawing including fixtures,necessarywelding andpainting withone coatsof anticorrosive paint and two coats of oil painting complete. 14 Providing and fixing mild steel grill gate with angle iron frame 65mm x 65mm x 10mm with iron bars at 150mm C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kilogram/Smt. 15 Providing internal cement plaster 20mm thick inSingle coats in cement mortar 1:4without neerufinish,toconcrete,bricksurface,inallpositionsincludingscaffoldingandcuringetc.complete. 16 Providingandlayinginsitu/readymix/readymixM10 cement concreteoftrap/granite/quartzite/ gneiss metal in foundation includingnecessarycentering,formwork,bailingout water, compactingandcuringetc.complete.(withfullyautomaticmicro processor based PLC withSCADA enabled with reversible drum type mixer/ concrete batch mix plant (pan mixer) with natural /artifical sand) 17 ProvidingandfixingheavydutyinterlockingconcreteRUBBERMOULDGLOSSY PAVING BLOCKS of 60 millimeter thickness of having a strength of 400 Kilogram/sq.m of approved quality and shape on a bed of crushed sand of 25 to 30 millimeter thick including striking joints and cleaningetc. complete. (using 100% crushed sand) 18 GARDEN SOIL :- supplying on site garden soil, well sieved 90% to pass through I.S. sieve of 10mm size free from stones rubbish like dried grass roots and other such materials. The soil should be fresh from quarry. The colour the soil generally be red. The soil will be measured by measuring box. (Farma) (Item includes Royalty charges, octroi, Corporation Tax Transporting Loading Unloading etc.) (Lead charges per 26 Km. considered) (As per the Approved quotation attached) 19 Providing and applying colour-wash of approved colour and shade in one coat to new surface including scaffolding, brushing and brooming down (excluding base coats of white wash) etc.complete. 20 Providing and applying plastic emulsion paint of approved quality, colour and shade tonew surface in three coats including scaffolding, preparing the surface. (excluding primer coat) etc. complete. 21 Providing and laying Cast in situ/Ready Mixcement concrete inM20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting,rougheningthemif specialfinishistobeprovided,finishingunevenand honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered bygunnybag,plastic,tarpaulinetc. (Woodencenteringwillnotbeallowed.),withfully automaticmicro processorbasedPLCwithSCADAenabledreversibleDrum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 22 Transportation of Material obtained from debries of various sorts including necessary excavation / loosing including loading,unloading and conveying and disposing as directed. 23 HANDLING CYCLE AREA – 1mtr 210mm x 610mm x 450mm :- Main frame 70mm x 70mm Made from “B” class G.I Pipe. :- Handling pipe – 1mtr 260mm 2(pis ) 40mm 12gage Made from “B” class G.I Pipe. :- Seat support Pipe- 650mm1mtr 650mm 12 gage 50mm Made from “B” class G.I Pipe. :- Paidal support Pipe- 460mm (2pis ) 50mm x 50mm 12gage Made from “B” class G.I Pipe. :- Clamp- 80mm x 80mm Thickness 8mm :- Circle – 320mm (2 pis ) Thickness 8mm:- Paidal pipe – 150mm x 100mm Made from “B” class G.I Pipe. :- Seat – 280mm x 200mm galvanized 2mm :- The pins used are made up 25mm bright bar :- The bearings used are “6205zz” permanent Lubricated sealed bearing of reputed make (SKF/FAG) :- High tensile steel with galvanized nut bolts are used from assembly. :-The serclips used for assembly are of 25mm. :- The colour used from standard oil paints 24 CHEST PRESS/BUTTERFLY MACHINEAREA: - 0.71Mtr x 1.72Mtr.SAFE AREA: - 0.86Mtr x 2.48Mtr.Providing and fixing chest press made from “B” Class G.I. pipe.The center pipe is of Ø115mm made from “C” Class G.I. pipe, andThe bottom support of M.S. round plate of Ø250 mm & 10mm thickness is welded at bottom.The remaining frame is made up of Ø40mm“C” class G.I. pipe.The handle frame is made up of Ø32mm “C” class G.I. pipe .For the assembly different bushes are used which is made from 50mm with 3mm thicknessseamless pipe & 50mm solid bar is used.The foundation used for fixing is consists of three equal items i.e. Ø115mm made from “C” ClassG.I. pipe, M.S. Round plate of Ø250 mm & 10mm thickness & 25 mm X 25mm X 3mm M.S. angle.The seats is fitted on the outer frame is made up of high quality FRP material of size 330 mm X300 mm of thickness 3 mm & M.S. Plate of thickness 5 mm and Size 250 mm X 200 mm is usedto Support it.Closing Caps are made from top quality FRP material which is of 2 mm thickness.The pins used are made up of Ø25 mm & Ø17mm solid bar.The bearings used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputedmake (FAG/SKF).High tensile steel with galvanized nut bolts are used for assembly.The serclips used for assembly is made up of Ø25 mm & Ø17mm.The powder coat is done by Poly urethane & Epoxy powder with 60 to 70 micron thickness 25 ROWERArea:- 1.2 x 1Mtr.Safe Area:- 1.5 x 1.5Mtr.Providing and fixing rower made from “B” Class G.I. Pipe.The Main frame is of 80mm X 40mm & 40mm X 40mm CRC Pipe with 2 mm thickness.The handle frame is of Ø32made from “C” class G.I. pipe.The Foundation used for Fixing consists of three equal items i.e. Ø40mm made from “C”Class G.I. pipe, C channel of 75mm X 40mm X5mm & 25mm X 25mm X 3mm M.S. angle.To join the movement frame to main frame seamless pipe of Ø50mm & 3mm thicknessis used.The seats which are fitted on the main frame is made up of high quality FRP material ofsize 330mm X 300mm of thickness 3 mm & M.S. plate of size 250mm X 200mm X 5mm isused to support it.Closing caps are made from top quality FRP material which is of 2 mm thickness.The pins used are made up of Ø17mm hardened bright bar.The bearings used are of “6203zz” permanent lubricated sealed bearing of reputedmake (FAG/SKF).The handles used are of Rubber grip.High tensile steel with galvanized nut bolts are used for assembly.The bushes (Stopper) used to avoid the collusion.The serclips used for assembly is of Ø17 mm.The powder coat is done by Poly urethane & Epoxy powder with 60 to 70 micronthickness. 26 SHOULDER BUILDER/HAND ROLLERArea:- Ø0.89Mtr. Safe Area:- Ø1.5Mtr. Providing and fixing Shoulder Builder made from “B” Class G.I. pipe. The Center Pipe is of Ø 115mm made from “C” Class G.I. pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The handle movement frame is of Ø32mm & Ø25mm made from “C” Class G.I. pipe. To Join the centre pipe & handle movement frame seamless pipe of Ø 130mm & 3mm thickness is used. The foundation used for fixing consists of three equal items i.e. Ø 90mm made from “C” class G.I. Pipe, M.S. Round Plate of Ø 250 mm & 10mm thickness & 25 mm X 25mm X 3mm M.S. angle. Closing caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of Ø 25 mm bright bar. The bearing used is “6201zz” & “6205zz” permanent lubricated sealed bearing of reputed make (FAG/SKF). High tensile steel with galvanized nut bolts are used for assembly. The serclips used for assembly is of Ø 25 mm. The Poly Urethane plastic bush is used for handling. The powder coat is done by Poly urethane & Epoxy powder with 60 to 70 micronthickness 27 Multifunctional Trainer:- 1300mm (L) x 700 mm (W) x 2100 mm (H)Metal :- All pipes make should be Tata or Jindal. All pipes should be of C class heavy grade as per IS2139 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Pipe end close cap- SS 304 grade should be used for protection of pipe end closing.Instruction Sticker- Instruction sticker of size 150mm x 230mm of SS 304 grade plate with 0.8mm thickness & riveted on 5mm thick MS plate. Safety & Maintenance- All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100kg.Hardwares- All Nuts, Bolts, washers should be ofSS 304 material. 28 Cross Trainer:- 1300mm (L) x 510 mm (W) x 1500 mm (H)Metal :- All pipes make should be Tata or Jindal. All pipes should be of C class heavy grade as per IS2139 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make. Rubber- High quality rubber should be used for the handle grips. Bearings and Pins- All bearings should be of SKF 2RS1 type and press fitted for smooth rotation, and does not require relubrication i.e. maintenance free ball bearing. Pins should be case hardened and centreless grinede finish for life long durability.Pipe end close cap- SS 304 grade should be used for protection of pipe end closing, bearings and bushes open end closed.Instruction Sticker- Instruction sticker of size 150mm x 230mm of SS 304 grade plate with 0.8mm thickness & riveted on 5mm thick MS plate.Safety & Maintenance- All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100kg.Hardwares- All Nuts, Bolts, washers should be ofSS 304 material. 29 Providingandfixing90cmx60cm Graniteplateengraving10cm. heightletter,figures including painting the lefters/figures with approved colour and shade complete
