Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc. 15cm thickness (below or above ground level), complete all as specified and directed. |
| 2 | M&L for 75mm thick PCC (1:4:8) type D- 2,(using 40mm graded crushed stone aggregatet) as in floors, pavings or plinth protection etc., complete all as specified and directed. |
| 3 | M&L for 100mm thick PCC (1:2:4) type B-2 (using 40mm graded stone aggregate) as in sub-bases, floors and pavings etc.,complete as specified and directed. |
| 4 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons and wall/dado etc, complete all as specified and directed. |
| 5 | M&L for chequered cement concrete tiles 30cm x 30cm x 20 to 25mm thick, with grey cement and pigments, jointed and pointed in neat cement slurry in floors over and including screed bed or bedding layer of CM (1:6), 15mm thick, complete all as specified and directed. |
| 6 | M&L for 60mm thick machine pressed precast concrete coloured interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006, M-35 grade, complete all as specified and directed. |
| 7 | M&L for 80mm thick machine pressed precast concrete coloured interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006, M-40 grade, complete all as specified and directed. |
| 8 | M&L for sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.( Note : Consolidation thickness shall be measured for payment.) |
| 9 | M&L for 1.5mm thick plastic dividing strips, width of strip 38mm, inserted in position, conform to design, complete all as specified and directed. |
| 10 | M&L for PCC (1:2:4) type B-0,(using 12.5mm graded crushed stone aggregate) as in copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work, complete all as specified and directed. |
| 11 | Dismantling of plain or corrugated steel sheeting any gauge thickness including nainital or similar pattern roof covering, complete all as specifed and directed. |
| 12 | Fixing only old CGI sheet, obtained against dismantiling, fixed with self tapping screws, complete all as specified and directed. |
| 13 | Fixing only old prepainted galvalume sheet, obtained against dismantiling, fixed with self tapping screws, complete all as specified and directed. |
| 14 | S&F pre painted galvalume aluminium zinc coating, GI based corrugated steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and directed. |
| 15 | S&F pre painted galvalume aluminium zinc coating, GI based plain steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and directed. |
| 16 | S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations fixed with self tapping screws with grade of zinc coating 275, complete all as specified and directed. |
| 17 | S&F 0.63mm thick plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, complete all as specified and directed. |
| 18 | M & L for preparing new zinc (or galvanised) surfaces to receive painting by coating with mordant solution including washing and cleaning, etc at any height and applying two coats of synthetic enamel paint (1st grade quality) of approved tint/design, pattern over a coat of red oxide primer of any description over 10cm width or girth not otherwise described, complete all as specified and directed. |
| 19 | M&L for 4mm thick pre-painted E-fibre board, designer/decorative,fixed or laid/inserted to GI snap grid frame size 605mm x 605mm work for false ceiling hangers with 4mm to 6mm dia. G.I. (length as required) adjusting level, fixed to roof slabs/truss by means of ceilling cleats made out of G.I. flat 40 x 3mm size 60mm long and expansion hold fasteners, 12.5mm dia, 40mm long including necessary dismentaling of existing unserviceable ceiling boards of any thickness including cover fillets, complete all as specified and directed. |
| 20 | M&L for PCC (1:2:4) type B-1, (using 20mm graded crushed stone aggregate) as in sides of chequered tiles path, rounded or chamfered on edges, complete all as specified and directed. |
| 21 | Dismantling wrought iron or mild steel work of any description not otherwise provided for and removing from site of work, complete all as specified and as directed. |
| 22 | S&F roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel ,rolled section or flat sections) of Fe-410w, (Gde E-250) including distance pieces, cleats etc, complete all as specified and directed. |
| 23 | S&F framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290, Gde-E-165, complete all as specified and directed. |
| 24 | M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise specifically provided for and applying two coat of synthetic enamel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed. |
| 25 | M&L for preparation of old painted steel or iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint (1st grade quality), complete all as specified and directed. |
| 26 | M&L for preparation of new steel or iron surfaces of any description n. exc. 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed. |
| 27 | Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and directed. |
| 28 | M & L for rendering 15mm thick in two coats (10mm under layer + 5mm top layer) on fair faces of brick work or concrete surfaces of wall in CM (1:4),mixed with water proofing compound on top layer as per manufacturer\"s instructions and finished the surface even and fair without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately) |
| 29 | Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification, complete all as directed. |
| 30 | M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed. |
| 31 | M&L 15mm thick rendering in CM (1: 6) on fair faces of brick work or concrete surfaces finished surfaces even and smooth without using extra cement, complete all as specified and directed. |
| 32 | M&L for preparing newly plastered surfaces of walls etc and applying two coats of distemper oil emulsion over a coat of chalk whitening primer, complete all as specified and directed. |
| 33 | Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, pillars etc., separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 m and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m, complete all as specified anddirected. |
| 34 | M & L for brick work with sub class \"B\"bricks, old size, burnt clay bricks, straight or curved on plan exc 6m mean radius built in CM (1:4), complete all as specified and directed. |
| 35 | Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm 4 core confirming to IS-7098 laid in trenches/ducts/fixed to poles wall/laid under roads/paths/drain/culverts or passing through pipes, complete all as specified and directed. |
| 36 | Excavation in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depth for foundation of pole/stay, or cable trenches and getting out in soft/loose soil, complete all as specified and directed. |
| 37 | Returning filling in including spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed. |
| 38 | Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed. |
| 39 | Supply and laying double walled corrugated (DWC) HDPE duct pipe of 40mm outer dia conformingto IS, approved colour complete with fittings for cable protection, complete all as specified and directed. |
| 40 | S&F GI tubing 50mm bore (light grade) with all fittings for protection of cables, laid in trenches including making good to the distrurbed surface,complete all as specified and directed |
| 41 | Supply and erection of asthetically designed decorative hot dipped galvanised mild steel step pole3.0 Mtrs height, opening window of300 x 110mm for terminalconnection and including mounting accessories and foundation boltswith grey powder finish compatible for fixingpost top luminaire of 40/45 Watt of max base mouting dia 76mmincluding necessary excavation and earth work, PCC foundation (1:3:6) type B-1 as per manufacturer\"s instructions, complete all as specified and directed. |
| 42 | Supply and fixing post top lantern LED type 45 watt AC 230 volts outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp, complete all as specified and directed. |
| 43 | Supply and fixing post top lantern LED type 40 watt AC 230 volts outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp, complete all as specified and directed. |
| 44 | Supply only automatic digital clamp meter LCD display with a maximum reading of 2000 count, 600 Amp AC/DC with leads and 03 set of suitable additional batteries, complete all as specified and directed. |
| 45 | Supply and fixingbollard LED type 9/10 watt AC 230 volts outdoor type withnecessary foundationand connection strip complete with driver and lamp, complete all as specified and directed. |
| 46 | REPAIR TO CHAIR EASY (FD-229)M & L for replacement of damaged front legs of chair easy with well seasoned 1st classteakwood, all as per drawing, including taking out old legs, complete all as specified and directed. |
| 47 | All as per item No. 46.00 here-in-before but rear legs, complete all as specified and directed. |
| 48 | All as per item No. 46.00 here-in-before but arm rest of chair easy, complete all as specified and directed. |
| 49 | All as per item No. 46.00 here-in-before but fillet for canning, complete all as specified and directed. |
| 50 | All as per item No. 46.00 here-in-before but rail of seat and back, complete all as specified and directed. |
| 51 | REPAIR TO CHAIR DINING (FD-279)M & L for replacement of damaged front leg of chair dining with well seasoned 1st class teak wood, all as per drawing, including taking out old leg, complete all as specified and directed. |
| 52 | All as per item No. 47.00 here-in-before but rear leg, complete all as specified and directed. |
| 53 | All as per item No. 47.00 here-in-before but back rest, complete all as specified and directed. |
| 54 | All as per item No. 47.00 here-in-before but stiffener, complete all as specified and directed. |
| 55 | All as per item No. 47.00 here-in-before but side rail, complete all as specified and directed. |
| 56 | All as per item No. 47.00 here-in-before but front rail, complete all as specified and directed. |
| 57 | All as per item No. 47.00 here-in-before but back rail, complete all as specified and directed. |
| 58 | All as per item No. 47.00 here-in-before but fillet, complete all as specified and directed. |
| 59 | REPAIR TO TABLE DRESSING LADIES (FD-251)M & L for replacement of mirror of size 365mm x 1220mm x 5mm thick of selected quality fixed with teak wood framing of 45mm x 40mm size with 6mm thick commercial type ply wood, BWR grade for back all as per drawing including taking out old mirror, complete all as specified and directed. |
| 60 | M & L for replacement of sliding glass shutter of size 300 x 290 x 5mm thick, ordinary quality, as per drawing including taking out old glass shutter, complete all as specified and directed. |
| 61 | M & L for replacement of leg oftable dressing with new legs of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out ofold broken legs, complete all as specified and directed. |
| 62 | M & L for replacement of bottom of table dressing with 18/19mm thick particle board commercial type, exterior grade conforming to IS-3087-1989 (ISI marked) all other as per existing and as per drawing including taking out old bottom, complete all as specified and directed. |
| 63 | M & L for replacement of side of table dressing with 18/19mm thick particle board commercial type, exterior grade conforming to IS-3087-1989 (ISI marked) pested with 1 mm thick plastic laminated sheet teak veneer with approved adhesive all other as per existing and as per drawing including taking out old side, complete all as specified and directed. |
| 64 | M & L for replacement of back of table dressing with 18/19mm thick particle board commercial type, exterior grade conforming to IS-3087-1989 (ISI marked) all other as per existing and as per drawing including taking out old back, complete all as specified and directed. |
| 65 | M & L for replacement of top of table dressing with 18/19mm thick particle board commercial type, exterior grade conforming to IS-3087-1989 (ISI marked) pested with 1 mm thick plastic laminated sheet teak veneer with approved adhesive all other as per existing and as per drawing including taking out old top, complete all as specified and directed. |
| 66 | CHAIR DININGJCOs//Ors (FD/MAP-II/05)Removing old unserviceable PVC seat and provision of new PVC seat 4mm thick and and 4 x 10mm thick ribs moulded along with seat in single piece with holes & screwed with frame, complete all as specified and directed. |
| 67 | Removing the existing unserviceable front leg and replacing with new teakwood legs of section 55 x 30mm duly furnished and polished, complete all as specified and directed. |
| 68 | Removing the existing unserviceable rear leg and replacing with new teakwood legs of section 30 x 55mm duly furnished and polished, complete all as specified and directed. |
| 69 | Removing old unserviceable center stiffener of leg bottom and replacing with new french polished teakwood stiffener of legs bottom of size 20 x 25mm duly furnished and polished, complete all as specified and directed. |
| 70 | Removing old unserviceable side stiffener of leg bottom and replacing with new french polished teakwood stiffener of legs bottom of size 20 x 25mm duly furnished and polished, complete all as specified and directed. |
| 71 | S&F providing new front/side rail of chair dinining for supporting between side rail left and right of size 30 x 65mm x 2 Nos. duly furnished and polished, complete all as specified and directed. |
| 72 | REPAIR TO SOFA SET 4/5 SEATER (FD-281/373) Supply of foam cushion of size 530mm X 500mm X 100mm thick (32 grade high density cool foam) covered with tapesty cloth (not less than Rs.225/- per mtr cost of cloth) including stitching, complete all as specified and directed. |
| 73 | M & L for replacement of damaged front legs ofSofa set(4/5 Seater) with well seasoned 1st class teak wood, all as per drawing,including taking out old front legs, complete all as specified and directed. |
| 74 | M & L for replacement of damaged rear legs of Sofa set (4/5 Seater)with well seasoned1st class teak wood, all as per drawing,including taking out old rear legs, complete all as specified and directed. |
| 75 | M & L for replacement of damaged arm-rest ofSofa set (4/5 Seater)with well seasoned 1st class teak wood, all as per drawing, including taking out old arm-rest, complete all as specified and directed. |
| 76 | M & L for replacement of damagedfront and back rail of seat and back of sofa set (4/5 Seater) with well seasoned 1st class teakwood, all as per drawing including taking out old front and back rail, complete all as specified and directed. |
| 77 | M & L for replacement of damagedside rail of seat and back ofsofa set (4/5 Seater)with well seasoned 1st class teakwood, all as per drawing, including taking out old side rail, complete all as specified and directed. |
| 78 | M & L for replacement new stiffener of sofa set (4/5 Seater) seat and back of required size made out of well seasoned 1st class teak wood, all as per drawing, including taking out old stiffener, complete all as specified and directed. |
| 79 | REPAIR TO TABLE 900 x 900 x 760 (FD-88 & 291) M & L for replacement of table top of table 900 x 900 x 760mm with 18/19mm thick pre laminated particle board one side teak face (exterior grade) with 4mm thick teak wood edging all round, all as per drawing, complete all as specified and directed. |
| 80 | S&F new leg of table 900 x 900 x 760mm of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out broken legs, complete all as specified and directed. |
| 81 | S&F new front and back rail of table 900 x 900 x 760mm of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out broken front rail, complete all as specified and directed. |
| 82 | S&F new side rail of table 900 x 900 x 760mm of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out broken side rail, complete all as specified and directed. |
| 83 | S&F new stiffener of table 900 x 900 x 760mm of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out broken stiffener, complete all as specified and directed. |
| 84 | REPAIR TO TABLE CENTRE (FD-274) M & L for replacement of top of table centre with made out of 18/19mm thick pre laminated particle board one side teak face (exterior grade) with 4mm thick teak wood edging all round, all as per drawing, complete all as specified and directed. |
| 85 | S&F new leg of table centre of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out broken legs, complete all as specified and directed. |
| 86 | M & L for replacement of damaged front rail of table centre with well seasoned 1st class teak wood, all as per drawing including taking out old front rail, complete all as specified and directed. |
| 87 | M & L for replacement of damaged side rail of table centre with well seasoned 1st class teak wood, all as per drawing including taking out old side rail, complete all as specified and directed. |
| 88 | REPAIR TO TEAPOY (FD- 232 & 382)M & L for replacement of top of tea poy verandah made out of 18/19mm thick pre laminated particle board one side teak face (exterior grade) with 4mm thick teak wood edging all round, all as per drawing including taking out old top, complete all as specified and directed. |
| 89 | S&F new leg of tea poy of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out broken legs, complete all as specified and directed. |
| 90 | M & L for replacement of damaged front rail of tea poy with well seasoned 1st class teak wood, all as per drawing including taking out old front rail, complete all as specified and directed. |
| 91 | M & L for replacement of damaged side rail of tea poy with well seasoned 1st class teak wood, all as per drawing including taking out old side rail, complete all as specified and directed. |
| 92 | S&F new stiffener of tea poy of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out broken stiffener, complete all as specified and directed. |
| 93 | REPAIR TO PEG TABLE ( FD- 277 & 384) M & L for replacement of top of peg table made out of 18/19 mm thick pre-laminated particle board one side teak face (exterior grade) with 4mm thick teak wood edging all round, all as per drawing including taking out old top, complete all as specified and directed. |
| 94 | M & L for replacement of leg ofpeg table with new legs of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out ofold broken legs, complete all as specified and directed. |
| 95 | M & L for replacement of damaged side/front rail of peg table with well seasoned 1st class teakwood, all as per drawing including taking out old side rail, complete all as specified and directed. |
| 96 | Supply and fixing new stiffener/bottom rail of peg table of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out broken stiffener/bottom rail, complete all as specified and directed. |
| 97 | REPAIR TO BED PLYWOOD TOP ( FD- 246) M & L for replacement of top of bed ply wood made out of 12mm thick commercial plywood, BWR grade, fixed on top of bed plywood with screws all as shown on drawing including taking out old damaged bed top, complete all as specified and directed. |
| 98 | M & L for replacement of leg ofbed plywood top with new legs of required size made out of well seasoned 1st class teak wood, all as per drawing including taking out ofold broken legs, complete all as specified and directed. |
| 99 | M & L for replacement of damaged long rail of bed plywood top with well seasoned 1stclass teak wood, all as per drawing including taking out old long rail, complete all as specified and directed. |
| 100 | Provision of short rail plywood top by converting from long rail obtained from item No.13.20 here-in-before including cutting and made to shape and size of short rail from existing broken/unserviceable long rail and fixing the same to bed after removing the damaged short rail all asshown on drg, complete all as specified and directed. |
| 101 | M & L for repair to head board of bed plywood top by replacing with 4mm thick one side teak face plywood fixed to existing frame and edging with 4mm wide teak wood beading all as shown on drawing including taking out old head board, complete all as specified and directed. |
| 102 | All as per item No.55.40 here-in-before but foot board of bed ply wood top all as per drawing, complete all as specified and directed. |
| 103 | RECANNING OF CHAIR DINING (FD-279) AND CHAIR EASY(FD-229)Taking down oldworn out plastic cane from chair dining/chair writing/chair easy/Stool dressing and reweaving the same with new approved quality plastic cane 3mm wide half round, white, with bordering of 4mm wide half round white plastic cane, canning shall be done in godrej pattern, complete all as specified and directed. |
| 104 | REPAIR TO TABLE BED SIDE (FD- 276)M & L for new top/bottom of table bed side made out of prelaminated particle board 18mm thick (ISI marked) exterior grade one side teak face including 4mm thick teak wood beading all around the edges, all as per drawing, including removing of old unseviceable top, complete all as specified and directed. |
| 105 | All as per item No. 57.00 here-in-before but side made out of prelaminated particle board 18mm thick, complete all as specified and directed. |
| 106 | All as per item No. 57.00 here-in-before but back made out of 6mm ply wood, commercial grade (BWR grade), complete all as specified and directed. |
| 107 | All as per item No. 57.00 here-in-before but shelf made out of prelaminated particle board(ISI marked), complete all as specified and directed. |
| 108 | REPAIR TO HAT STAND WITH MIRROR (FD- 233)M & L for removing of existing unseviceable mirror and replacing with new mirror, 5.5mm thick electro copper plated mirror of polished sheet with 6mm x 35mm teak wood edging, all as per drg, complete all as specified and directed. |
| 109 | M & L for removing of existing unseviceable peg of hat stand and replacing with copper oxidised steel peg, all as per drg, complete all as specified and directed. |
| 110 | M & L for key plate of hat stand made out of3mm thick MS plate of size 40mm x 25mm including removing of existing unseviceable key plate, as per drawing, complete all as specified and directed. |
| 111 | M & L for venear of hat stand made out of4mm thick teak venear ply including removing of existing unseviceable key plate, as per drawing, complete all as specified and directed. |
| 112 | M & L for frame beading of hat stand made out of6 x 35mm size frame beading all round of 1st class hard wood including removing of existing unseviceable key plate, as per drawing, complete all as specified and directed. |
| 113 | M&L for preparation of surfaces by removing of old existing fade out polish from chair wooden bottom by scrapping or with caustic soda and rubbed down by emery paper including filled up the cracks and pores with a paste of putty and applying two coats of french polish of approved quality/PFU with high gloss finish on exposed surfaces to view, complete all as specified and directed. (Drg No. FD-225/285) |
| 114 | All as per item No. 59.00 here-in before but chair dinning, complete all as specified and directed. (Drg No. FD-279) |
| 115 | All as per item No. 59.00 here-in before but table dressing ladies, complete all as specified and directed. (Drg No. FD-251) |
| 116 | All as per item No. 59.00 here-in before but table 3\" x 3\", complete all as specified and directed. (Drg No. FD-88/291) |
| 117 | All as per item No. 59.00 here-in before but table centre, complete all as specified and directed. (Drg No. FD-274) |
| 118 | All as per item No. 59.00 here-in before but teapoy, complete all as specified and directed. (Drg No. FD-232 & 382) |
| 119 | All as per item No. 59.00 here-in before peg table, complete all as specified and directed. (Drg No. FD-277 & 384) |
| 120 | All as per item No. 59.00 here-in before but bed ply wood top/hard bed, complete all as specified and directed. (Drg No. FD-246) |
| 121 | All as per item No. 59.00 here-in before but sofa set 5 seater, complete all as specified and directed. (Drg No. FD-281/ 373) |
| 122 | All as per item No. 59.00 here-in before but sofa set 4 seater, complete all as specified and directed. (Drg No. FD-281/ 373) |
| 123 | All as per item No. 59.00 here-in before but table bed side, complete all as specified and directed. (Drg No. FD-276) |
| 124 | All as per item No. 59.00 here-in before but hat stand with mirror, complete all as specified and directed. (Drg No. FD-233) |
| 125 | All as per item No. 59.00 here-in before but chair dining JCO/ORs, complete all as specified and directed. (Drg No. FD/MAP-II/05) |
| 126 | Removing old u/s PVC shoes from various type of chairs such as chair dinning, chair writing, chair easy, chair WB etc. and replacing the same with new 20mm dia and 10mm high PVC cap screwed to bottom of legs with CP screws/nail, complete all as specified and directed. (Drg No. FD - 281, 225, 285, 229 & 280) |
| 127 | STEEL FURNITUREREPAIR TO ALMIRAH LARGE STEEL (FD- 67M & 1031) & ALMIRAH LARGE 1/2H & 1/2S Taking down old unserviceable locking device of almirah large steel and supply and fixing new lock of suitable size provided with duplicate keys as per sample, fixed with screws, all as per drawing, complete all as specified and directed. |
| 128 | M & L for repairing locking device of almirah steel large including lock bar, complete all as specified and directed. |
| 129 | M & L for repairing of door shutters of almirah steel large by denting and necessary adjustment, as required, complete all as specified and directed. |
| 130 | Taking down old unserviceable handle of almirah large steel and supply and fixing new chromium plated handle, fixed with screws, all as per drawing, complete all as specified and directed. |
| 131 | Taking down old unserviceable legs of almirah large steel and supply and fixing (by welding) new legs made out of 1mm thick mild steel black sheet and applying two coats of spray painting with synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer including preparation of surfaces of new legs, all as per drawing, complete all as specified and directed. |
| 132 | Taking down old unserviceable shelves of almirah large steel and supply and fixing (by welding) new shelves made out of 1mm thick mild steel black sheet made to shape and applying two coats of spray painting with synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer to new srfaces of shelves including preparation of surfaces, all as per drawing, complete all as specified and directed. |
| 133 | M & L for running welding in repair to broken/damaged sides (left/right), back and top of almirah steel large, complete all as specified and directed.(Note : Thickness of material to be welded n. exc. 2mm and length of each welding exc. 10mm but n. exc. 20mm). |
| 134 | REPAIR TO LOCKER STEEL (FD- 1029)Taking down old unserviceable legs of locker steel and supply and fixing (by welding) new legs made out of 1mm thick mild steel sheet and applying two coats of spray painting with synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer to new legs including preparation of new surfaces, all as per drawing, complete all as specified and directed. |
| 135 | M & L for replacement for old damaged hasp and staple of locker steel with new hasp and staples of chromium plated safety type 100mm long, complete all as specified and directed. |
| 136 | Taking down old unserviceable handle of locker steel and supply and fixing new chromium plated steel handle, of 100mm size, ‘D’ type, complete all as specified and directed. |
| 137 | Taking down old unserviceable hinges of locker steel and supply and fixing new mild steel hinges, 75mm size of approved quality, complete all as specified and directed. |
| 138 | M & L for repairing of door shutters of locker steel by denting and necessary adjustment as required, complete all as specified and directed. |
| 139 | S&F 20mm dia stainless steel conduit pipe as a hanging rod all as per drawing iincluding taking out old unserviceable pipe, complete all as specified and directed. |
| 140 | S&F new shelves made out of 1mm thick plain sheet, all as per drawing iincluding taking out old unserviceable shelves, complete all as specified and directed. |
| 141 | M & L for running welding in repair to broken/damaged sides (left/right), back and top of locker bed sidw steel, complete all as specified and directed.(Note : Thickness of material to be welded n. exc. 2mm and length of each welding exc. 10mm but n. exc. 20mm). |
| 142 | REPAIR TO CHARPOY GI PIPE (FD-220)M&L for replacement of angle iron of size 25 x 25 x 5mm thick, 225mm long welded to long rail and short rail at corners of charpoy GI pipe drilling holes for fixing plywood with bolts and painting to angle iron pieces with two coats of black synthetic enameled paint (1st grade quality) over a coat of red oxide zinc chrome primer including taking out old one, complete all as specified and directed. |
| 143 | M&L for replacement ofangle iron of size 25 x 25 x 5mm thick, 850mm long welded to long rail horizontally (one end to each long rail) at equal distance including drilling holes where ever required for fixing plywood with bolts and painting to angle iron pieces with two coats of black synthetic enameled paint (1st grade quality) over a coat of red oxide zinc chrome primer including taking out old one, complete all as specified and directed. |
| 144 | M&L for replacement ofcommercial plywoodtop of charpoy GI pipe size 1950mm x 900mm x 12mm thick, BWR grade, confirming to IS 303-1975 with 4mm wide 2nd class hard wood beading all-round the plywood,fixed to charpoy frame with and including nuts, bolts and GI washers (minimum 12 Nos. per charpoy), dia of bolt not less than 8mm including taking out old unserviceable plywood top, complete all as specified and directed. |
| 145 | Dismantling of old unserviceable / worn outlong rail of the charpoy GI pipe and replace the same with new long rail made out of 32mm GI pipe including cutting threading etc. without damaging other parts, all as per drawing, complete all as specified and directed. |
| 146 | M&L for replacement of short rail (converted from U/S long rail), complete all as specified and directed. |
| 147 | M&L for replacement of legs converted from U/S short rail, (complete with clamps for FMN set), complete all as specified and directed. |
| 148 | M&L for replacement ofwooden plugs made of 2nd class hard wood, as per drg, complete all as specified and directed. |
| 149 | M&L for replacement ofGI elbow, three way (ISI marked) 32mm dia, complete all as specified and directed. |
| 150 | M&L for replacement of GI check nut (ISI marked), complete all as specified and directed. |
| 151 | REPAIR TO ALMIRAH MEDIUM STEEL (FD-67M & 1032)Taking down old unserviceable locking device from almirah medium steel and supply and fixing new lock of suitable size provided with duplicate keys, complete all as specified and directed. |
| 152 | M & L for repairing of door shutters by denting and necessary adjustment as required, complete all as specified and directed. |
| 153 | Taking down old unserviceable handle and supply and fixing new chromium plated brass handle, of size 125mm, fixed with screws, all as per drawing, complete all as specified and directed. |
| 154 | Taking down old unserviceable legs of almirah medium steel and supply and fixing (by welding) new legs made out of 1mm thick mild steel black sheet and applying with two coats of spray painting with synthetic enameled paint (1st grade quality) over a coat of red oxide zinc chrome primer to new legs including preparation of surfaces, all as per drawing, complete all as specified and directed. |
| 155 | Taking down old unserviceable shelves of almirah medium steel and supply and fixing new shelves made out of 1mm thick mild steel black sheet made to shape and applying two coats of spray painting with synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer to new surfaces of shelves including preparation of surfaces, all as per drawing, complete all as specified and directed. |
| 156 | M&L for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel large, complete all as specified and directed.(Note: Thickness of materials to be welded n. exc 2mm thickness and length of each welding exc 10mm and n. exc 20mm in length) |
| 157 | REPAIR TO BED HARD STEEL (FD/E6/MAP/08R)M & L for replacement of plank of head rest by replacing with 18mm thick pre-laminated particle board screwed to MS strip and welded to 18mm rectangular pipe, all as per drawing including taking out old unserviceable plank of head rest, complete all as specified and directed. |
| 158 | M & L for replacement of plank of foot rest by replacing with 18mm thick pre-laminated particle board screwed to MS strip and welded to 18mm rectangular pipe, all as per drawing including taking out old unserviceable plank of head rest, complete all as specified and directed. |
| 159 | M & L for spot welding n. exc. 2.50cm in length of broken steel frame of bed hard steel. All joints welding and fixing shall be done in accordance with standard workmaship/specification and all steel member shall be powder coated, complete all as specified and directed. |
| 160 | M&L for replacement of top of bed hard steel with 12mm thick plywood, BWR grade, to same platform with screw including removing of old unseviceable plywood top, complete all as specified and directed. |
| 161 | REPAIR TO CHARPOY IP HARD TOP (FD/MAP-II/01)M&L for replacement of top of charpoy with 12mm thick plywood, BWR grade, to same platform with screw including removing of old unseviceable plywood top, complete all as specified and directed. |
| 162 | M & L for spot welding n. exc. 2.50cm in length of broken steel frame of charpoy IP hard top. All joints welding and fixing shall be done in accordance with standard workmaship/specification and all steel member shall be powder coated, complete all as specified and directed. |
| 163 | REPAIR TO TABLE OFFICE CLERK STEEL (FD-84M, 84 & 1004)M & L for replacement of table top office clerk steel of size 1370mm X 760mm with 18/19mm thick one side teak face pre-laminated particle board (exterior grade) with 4mm thick teak wood edging all round and fixed with screwsall as per drawing including taking out old unserviceable top, complete all as specified and directed. |
| 164 | M & L for replacement drawermade out of 1mm thick MS black sheet including making shape, welding and painting with two coats of spray painting with synthetic enamel paint (1st grade quality)over a coat of red oxide primer all as per drawing including taking out old unserviceable drawer, complete all as specified and directed. |
| 165 | M & L for replacement of damaged legs / stiffener with25mm MS square tube ofwall thickness 1.6mm by welding complete and applying with two coats of spray painting with synthetic enamel paint (1st grade quality) over a coat of red oxide primer all as shown on drawing including taking out old unserviceable leg / stiffener, complete all as specified and directed. |
| 166 | M & L for replacement of unserviceable lock of drawer with new lock of 6 lever 65mm long (best quality) with double key, complete all as specified and directed. |
| 167 | REPAIR TO TABLE OFFICER STEEL (FD-1003)M & L for replacement of table top oftable office officer steel 1680mm x 870mm with 18/19mm thick one side teak face pre-laminated particle board (exterior grade) with 4mm thick teak wood edging all round and fixed withscrews with frame all as per drawing including taking out old unserviceable top, complete all as specified and directed. |
| 168 | M & L for replacement of damaged drawer of table made out of 1mm thick MS black sheet including making shape, welded with gas welding and painting with two coats of synthetic enamel paint over a coat of red oxide primer all as per drawing &including taking out old unserviceable drawer, complete all as specified and directed. |
| 169 | M & L for replacement of damaged legs/stiffener with 25mm MS square tube ofwall thickness 1.6mm and welding complete and painting with two coats of synthetic enamel paint over a coat of red oxide primer all as shown on drawing &including taking out old unserviceable leg/stiffener, complete all as specified and directed. |
| 170 | M & L for replacement of unserviceable lock of drawer with new lock of 6 lever 65mm long (best quality) with double key, complete all as specified and directed. |
| 171 | REPAIR TO TABLE DINING OR\"S (FD-165M)M & L for replacement of top of table dining with 18/19mm thick one side teak face pre-laminated particle board (exterior grade) with 4mm thick teak wood edging all round and fixed withscrewedall as per drawing & taking out old top, complete all as specified and directed. |
| 172 | M & L for replacement of damaged legs with 25mm MS square tube ofwall thickness 1.6mm by welding complete and painting with two coats of synthetic enamel paint over a coat of red oxide primer all as shown on drawing & taking out old leg , complete all as specified and directed. |
| 173 | M & L for replacement of centre stiffener and long rail with 25mm MS square tube of wall thickness 1.60mm welded to frame complete and painting with two coats of synthetic enamel paint over a coat of red oxide primer all as shown on drawing including taking out old stiffener and long rail, complete all as specified and directed. |
| 174 | All as per item No. 74.20 here-in before but short stiffener and short rail, complete all as specified and directed. |
| 175 | M & L for scrapping out old painted (external and internal) surface ofalmirah large steel and applyingtwo coats of spray painting with synthetic enamel paint (1st grade quality) over a coat ofred oxide zinc chrome primer including preparation of surfaces and filling cavities with putty, complete all as specified and directed. (Drg No. FD- 67 & 1032) |
| 176 | All as per item No 75.00 here-in-before but almirah medium steel, complete all as specified and directed. (Drg No. FD- 67 & 1032) |
| 177 | All as per item No 75.00 here-in-before but locker steel, complete all as specified and directed.(Drg No. TD, FD- 1029) |
| 178 | All as per item No.75.00 here-in-before but bed hard MAP, complete all as specified and directed.(Drg No. FD/E6/MAP/08R). |
| 179 | All as per item No.75.00 here-in-before but charpoy IP hard top, complete all as specified and directed.(Drg No. FD/MAP-II/01). |
| 180 | All as per item No 75.00 here-in-before but table office clerk steel, complete all as specified and directed.(Drg No. FD- 1004) |
| 181 | All as per item No 75.00 here-in-before but table office officer steel, complete all as specified and directed. (Drg No. FD- 1002) |
| 182 | All as per item No.75.00 here-in-before but table dining ORs, all as per existing and as approved, complete all as specified and directed. (FD-165M) |
| 183 | M & L for providing new hard rubber shoe for table office clerk steel, bed har MAP, charpoy IP hard top, all as per existing and as approved, complete all as specified and directed. (FD-/E6/MAP/08 (R), FD/MAP-II/01, FD-1004) |
| 184 | Note: An amount of Rs.61,195.00 on account of Credit Schedule for schedule \"A\" part - II shall be deducted from the total amount of BOQ to arrive at the contract sum. |
| 185 | Supply and fixing energy efficient ‘LED Flood Light120 W LED luminairewith Aluminium dia cast housing, toughened glass cover with IP 66 protection, CCT 5700 K including fixing arrangment on wall/pole / surface and connecting cable up to nearest ceilign rose into flexible PVC conduit. Make : Crompton/Havells/ Surya/Philips |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
