construction of Foundation For Drought Pump At Shalifur Hp Bagh For Augmentation Of Dubji Canal Civil Part Rdddc2526128847- Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil : 2 Filling available excavated earth (excluding rock) in trenches, plinth, sides offoundations etc. in layers not exceeding 20 cm in depth, consolidating each depositedlayer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 3 Dumping stone excluding cost of stones in Horizontal on level 4 Stone boulder (nallah) nominal size 225 mm (Stack measurements reduced by 15%) 5 Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 6 Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 7 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level.1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) 8 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing inposition and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. 9 Centering and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns etc. for mass concrete. 10 Centering and shuttering including strutting, propping etc. and removal of form for:Walls (any thickness) including attached pilasters, buttresses, plinth andstring courses etc. 11 Centering and shuttering including strutting, propping etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platforms. 12 Centering and shuttering including strutting, propping etc. and removal of form for. Edges of slabs and breaks in floors and walls. Under 20 cm wide. 13 Boring, providing and installing bored cast-in-situ reinforced cement concrete pile of specified grade concrete mix, diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embeded in the pile cap etc. all complete including removal of excavated earth with all lifts and leads(Length of pile for payment Shall be measured from top of shoe to the bottom of pile cap). By Crawler mounted, telescopic boom hydraulic pilling Rig all complete.600 mm dia piles 14 Brick Work 15 Providing and installation of ISI marked heavy duty single winch machine including all assessories including carriage, painting etc complete job 16 Providing wood work in frames of doors, windows, clerestory windows andother frames, wrought framed and fixed in position with hold fast lugs or withdash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Kiln seasoned and chemically treated hollock wood 17 Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Second class Kail wood 18 Providing and fixing wire gauze shutters using galvanized M.S. wire gauze ofaverage width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction ofEngineer-in-charge :Second class Kail wood 19 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area ofopening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Second Class teak wood 20 Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 21 15mm Cement plaster on the rough side of single or half brick wall ofmix: 1 : 4 ( 1 cement : 4 fine sand) 22 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) 23 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer 24 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 gradedstone aggregate 20 mm nominal size). 25 Providing and fixing aluminum tower bolts ISI marked anodized (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed torequired colour or shade with necessary screws etc. complete :150x10 mm 26 Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to requiredcolour and shade with necessary screws etc. complete.125 mm 27 Providing and fixing bright finished brass 100 mm mortice latch and lock, ISImarked, with six levers and a pair of anodized (anodic coating not less thangrade AC 10 as per IS : 1868) aluminum lever handles of approved quality withnecessary screws etc. complete. 28 Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws, (Shutter area to be measured). 29 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. 30 Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 31 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer)pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Providing and fixing PPR Unions.PPR union 25 mm 32 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer)pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Internal work-exposed on wall with clamps at 1.00 meter spacing.PN-16 pipe , 25mm OD(SDR-7.4) 33 Providing and Fixing soil, waste and vent pipes 1mm thick PVC S&S pipe (150mm dia) 34 Providing and Fixing Soil, waste and vent pipes 1mm thick PVC S&S pipe (100mm dia) 35 Providing and Fixing in position PVC floor Traps (100mm dia) 36 Providing and Fixing bend of required degree with door, inspection rubber washer 3mm thick, bolts and nuts complete PVC S&S pipes.(100mm) 37 Providing and Fixing bend of required degree with door, inspection rubber washer 3mm thick, bolts and nuts complete PVC S&S pipes.(75mm) 38 Constructing brick masonry chamber for underground C.I. inspectionchamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick withcement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line- 39 Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the walls wherever required :White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap 40 Providing and fixing 15 mm nominal bore C.P. brass bib cock ofapproved quality conforming to IS : 8931 41 Wiring for Circuit/Sub-main wiring along with earth in FRLS PVC insulated 660/1100 volt grade flexible stranded copper conductor wires of polycab/Finolex/Anchor/Havells make, to be laid in recessed or surface conducting system (including cost of required size and dia conduit with allied accessories) of following sizes.2x4 sq.mm +1x4 SQ.MM Earth Wire 42 Providing and fixing 5/6 A switch of aproved brand including all allied accessories complete job. 43 Supply, Installation, Testing and commissioning of ceiling fan of aproved brand viz HAVALES ,PHILLIPS ,GOLD MEDAL etc including all accessories complete job. 44 Supply, Installation, Testing and commissioning of 12 watt LED surface/recessed Down lighters having CRCA/Aluminium Body (commercial type) minimum lumens 100lm/w the luminaries housing should be crca /aluminium and the luminary optics shall have a high efficiency with transmittance, average life of 50000 hrs operating temperature-10C to + 45C of philips/Havells/Wipro/Helonix/Jaguar/Trulux make incl making of necessary Connections. The job further includes replacement warrenty of fixture (if damaged) /burnt out what so ever reason for a period of two years reckoned from date of successful commissioning/handing over of site to intending department. 45 Carriage of material by mechenical transport from source to actual site of work including loading,unloading ,stacking complete job. 46 Cement by an average lead of 10 KMby MT 47 Sand by an average lead of 10 KM by MT 48 20 mm Agg. By an avg lead of 10 KM by MT 49 40 mm Agg. By an average lead of 10 KM by MT 50 Stoneby an average lead of 10 KM by MT 51 Bricksby an average lead of 10 KM by MT 52 Steel by an average of 10 KM by MT