|
| 1 | Provision of new bore well near B block & water pipe line & sluice valve connected to overhead tank pipe line at OCFS Estate |
| 2 | Excavating in trenches n.exe.1.5m wide and n.exe.1.5m in depth for foundation, getting out soft & loose soil. |
| 3 | M&L broken brick hardcoreof gauge n.exc 63mm , deposited , spreaded andlevelledin layersn.exc. 15cmthickwatered andrammedto a true surface |
| 4 | M&L Cement conerete in foundations filling and mass concrete Type C2 1:3;6 (40mm stone aggregate). |
| 5 | Reinforced cement concrete type B-1 1:2:4 (20 mm graded aggregate) in columns ,pillars ,piers, posts and struts. |
| 6 | Reinforced cement concrete type B-1 1:2:4 (20 mm graded aggregate) in foundations including rafts footings foundation beams plinth beam base for columns etc |
| 7 | Reinforced cement concrete type B-1 1:2:4 (20 mm graded aggregate) in beams cantilevers, lintels over 1.5m span. |
| 8 | Reinforced cement concrete type B-1 1:2:4 (20 mm graded aggregate) in slab( flat & Inclined) supported on walls beams and columns in floors, roofs, landings. |
| 9 | M&L M.S. Bars 10 mm dia or over, cut to lenth, bent to shape and binding with M.S. wire as required/directed.(TMT bars). |
| 10 | M&LMild steel bars 6mm dia to 8mm dia, cut to length,bent to shap required, including cranking,bending and binding with mild steel wire (annealed) notless then 0.9mm dia. (TMT bars). |
| 11 | Form work to side of concrete foundation footings base of columns plinth beam etc.flat rough finished surface of concrete. |
| 12 | Formwork to sides and soffits of roof beams, beam haunchings, cantilevers, etc, flat rough finished surfaces of concrete. |
| 13 | Form work to sides of square,rectangular or polygonal pillars, posts struts, piers, columns and stanchions flat rough finished surfaces of concrete. |
| 14 | Formwork to soffits of suspended slabs as flat roof slabs (Horijontal or sloping), fair finished surfaces of concrete. |
| 15 | M&L for brick work with sub class \"A\"bricksstraight or curved on planexc. 6mmean radius built in1:4 mix cement mortarusing 100%coarsesand. |
| 16 | Rendering 12mm thick cement plaster in 1:4 mix cement mortar on walls. |
| 17 | Providing 70 mm Cement concretetype B-0, 1:2:4 (12.5mm graded aggregate)finishing cement concrete surface even and smooth without using extra cement concrete. |
| 18 | S/F of MS framed work for cladding glazing and like fixed with angle cleats and connecvting plates.Fe-290(Gde E-165). |
| 19 | S&F of Mild steel,1.60mm thick plain,black sheet in wall cladding,steel gates and similar work, cut to size,holes punched,including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required |
| 20 | M&L for steel rolling shutters, with out ball bearing, as specified thickness of laths in 1mm including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type. |
| 21 | S&F of Butt hinges , heavyweight cold rolled mild steel 125msize. |
| 22 | S&F Aluminium anodised, barrel tower bolts of extruded section and fixed 200 mm size. |
| 23 | S&F Aluminium handles, cast type, anodised 100 mm size. |
| 24 | S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 200 mm size. |
| 25 | S&F of steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded. |
| 26 | S&F of steel ventilators, fixed type, with glazing bars. |
| 27 | Sand filling under floors or in foundations including watering and consolidation |
| 28 | M&L of machine cut kota stone slab flooring 40-50mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 29 | S/F of light shed Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqmin floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. |
| 30 | S&F Non - skid Ceramic white tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 31 | Providing screed bedding layer of mortor 25 mm thick for laying floor finish 1:4 ratio. |
| 32 | S&F Glazed ceramicjoint free colour tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match. |
| 33 | S&Fixing in repair of vitreouschinasquattingpan of \"Orissa\" patternssize 580X440 mm whitewith integral footrest(excluding flushing cistern)\"P\" or \"S\" trap front or back inletofany pattern including lime concrete bedding connection to trap &flushing pipe includingtrap set,including flush pipe of polyethene of lowlevel of PVC 32 mm dia & concrete bedding & making good to floor. |
| 34 | S/Fixing in repair of PVC 10 litres valveless syphonic action type flushing cistern low valve white with inlet ball valve float and handle including brackets. |
| 35 | S&F of 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 36 | S&F PVC connections 15mm size with PTMT nuts of length 300mm. |
| 37 | S&F of fancy type 15mm Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule. |
| 38 | S&F PVC(SWR) pipe single socketed in any length with rubber ring joints, fixed to walls110mm bore. |
| 39 | S&F of bends PVC(SWR) 110mm bore. |
| 40 | S&F of junction single(single T), equal,or unequal,110mm bore. |
| 41 | S&F stop valve but fancy type, chromium plated serewed down high pressur with butterfly handle serewed both ends for Iron pipe or for union & fixed 15mm of bore. |
| 42 | S&F High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches 15mm with all fittings. |
| 43 | S&F High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches 25mm with all fittings. |
| 44 | S&F Vitreous China Wash basins, white,flat back, size 580X450 mm including cutting for and pinning in ends of brackets. |
| 45 | S&F of 15mm bore fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed |
| 46 | Preparation of new steel surface and apply two coat of synthetic enamel paint over priming with red oxide as specified.M&L complete. |
| 47 | M&L for apply 3 mm thick cement base wall care putty on wall. |
| 48 | M&L for apply 3 mm thick cement base wall care putty on ceiling. |
| 49 | Preparation of new plastered surface then apply two coat of distemper oil emulsion on ceiling. M&L complete. |
| 50 | Preparation of new plastered surfaceand apply two coat of paint plastic emulsion on wall as directed. M&L compete. |
| 51 | M&L for one light point or one fan point wiring controlled by one switch with 1.5 sqmm size, PVCsingle core sheathedcopper conductor cable in PVC conduitwith sunk cast iron or pressed steel terminal boxes with 3mm thick mica top. Cable should be Finolex / Havells / Polycab/anchoMake only. PVC conduit should be ISI marked and heavy grade. as per approved sample. |
| 52 | M&L Wiring for one 3pin socket outlet 5amp on sameboard with other switches with 1.5 sq.mm size, PVC single core sheathed copper conductor cable in PVC conduit.I S I MARKED &Make- Havells / Anchor / Polycab Only. as per approved sample. |
| 53 | S&FSocket out let 2 in 1, 3 pin , 5 Amp flush type ISI marked, Make- Havells / Anchor / Polycab Only. as per approved sample. |
| 54 | M&LLamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting insulated body with back plate for PVC Pipe fitting, ISI marked Make- Havells / Polycab/ Anchor Only.& as per approved sample. |
| 55 | M&L Switch piano, flush type single pole one way6 Amp.,I S I MARKED ,Make- Havells / Polycab/ AnchorOnly. as per approved sample. |
| 56 | M&L for Power point wiring for 15 amps socket outlet controlled by one switch with 2.5 sq.mm size, PVC single core sheathedcopper conductor cable in PVC conduit with sunk cast iron or pressed steel terminal boxes with 3mm thick mica top.Cable should be Finolex/ Havells /Polycab Make only.PVC conduit should be ISI marked and heavy grade.as per approved sample. |
| 57 | M&LSwitch piano, flush type single pole one way 16 Amp , I S IMARKED ,Make- Havells / Polycab/ AnchorOnly. as per approved sample. |
| 58 | S&F socket outlet 2 in 1, 3pin ,6 & 16 amp flush type , I S I marked , Make- Havells / Polycab/ Anchor Only. as per approved sample. |
| 59 | M&LCeiling ros ,3 pin PVC/ polycarbonate, isolated body Make- Havells / Polycab / Anchor Only. as per approved sample. |
| 60 | M&LMCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA. With box. |
| 61 | M&L MCCB 3 Pole .415 V. fixed type, 100 Amps withbreaking capacity 16 KA. With box. |
| 62 | S&F Single pole & neutral 4 way with 200 A rated bus bar 240 V with 200 amps rated bus bar. |
| 63 | Supply and fixing 240V, 10 KA \"B\" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning. Make -Havells / anchor/Polycab / Siemens Only. |
| 64 | S&F PVC insulated, armoured, heavy duty electric cable withaluminium conductor, 1100 volts grade, cross-sectional area70 sq. mm 4 core. |
| 65 | S&F Wiring for circuit/ submain wiring alongwith earthwire with FR is PVC insulatedcopper conductor, single core cable size 2x2.5 sq.mm +1x2.50 sq. mm earth wire in PVC Conduit.Cable should be Finolex / Havells / Polycab Make only. PVC conduit should be ISI marked and heavy grade.as per approved sample. |
| 66 | M&L Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less\"than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completionbut using galvanised iron strip 25×4mm as earthing lead.as per approved sample. |
| 67 | M&L Common salt commercial |
| 68 | M&L Charcoal dust/Breeze |
| 69 | Returning,fillingin ,including spreading, levelling, watering and well ramming in layers not exc 25 cm.soft loose soil |
| 70 | Boring with reverse rotary rig circulation method including electronic logging through any kind of strata of soil/rocks for drilling 525 mm dia hole for depth not exceeding 60 mtrs deep below ground level by keeping sufficient space for packing pea gravel complete all as specified. |
| 71 | All as per serial item No. 1 here in before but depth exceeding 50 metre but not exceeding 100 metre. |
| 72 | All as per serial item No. 1 here in before but depth exceeding 100 metre but not exceeding 150 metre. |
| 73 | All as per serial item No. 1 here in before but depth exceeding 150 metre but not exceeding 200 metre. |
| 74 | All as per serial item No. 1 here in before but for drilling depth exceeding 200 metre and not exceeding 300 metre below ground level. |
| 75 | Supplying, assembling, and lowering into bore hole (12 inch) bore dia MS casing pipe ERW conforming to IS 4270:2001 with 8mm wall thickness externally threaded and screwed ERW, in random lengths of 6 metre or as required, ISI marked including necessary fittings and jointing upto 60 mtrs depth from ground level, including providing two coats of anti-corrosive paint over a coat of primer on external surfaces of pipes complete all as specified anddirected. |
| 76 | All as per Srl Item No. 6 here-in-before but of 200 mm bore dia with 8mm wall thickness beyond 60metre below from ground level. |
| 77 | Strainer (slotted)MSpipe ERW 200mm boreconforming to IS 4270:2001, minimum wall thickness 8mm including screwed and socketed ends with coupling and socketed joints along with arc welding each length not exceeding 6 metre including lowering, duly painted with primer and two coats of anti corrosive paint complete all as specified. |
| 78 | Supplying and fixing 8 mm thick MS bail plug of 200 mm bore dia with 60cm lung MS pipe having wall thickness 8mm, with strong iron hook, screwed & arc welded to the casing pipe complete all as specified.Note:- Length of pipe requiredto be fixedwith bail plug will be measuredand paid for separately. |
| 79 | Supply and lowering into bore holes centering guide made out of MS flat iron of size 50mm x 6mm made to shape with two rings at 75 cm apart and three No. of ribs suitable for 250mm/350mm bore pipe complete all as specified. |
| 80 | Supplying and fixing of MS reducer of 8mm wall thickness screwed both ends of 300x200(1\"x6\"\") mm size of length 600mm including jointing screwed and socketed along with electric are welding complete all as specified and directed. |
| 81 | Supply and fixing well cap 200 mm bore having internal threads and with welded iron handle of 20mm dia MS round complete all as specified and directed. |
| 82 | Housing clamps made out of mild steel plate 12mm thick of size 700mm x 150mm including nuts, washers and bolts 20mm dia fully threaded of suitable length for 350mm bore housing pipe complete all as specified. |
| 83 | Supplying lowering and packing pea gravel of size 3mm to 6.00 mm all around the casing pipe and slotted pipe in the well bore to entire depth completeall as specified . (Volume of pee gravel shall be measured asspace between bore well and outer dia of pipe) |
| 84 | Supplying and fixing 80 mm bore GI pipe medium grade 6 Mtr long, 4 Nos in the angular space on four sides of the bore well and 30 cm above the ground level with suitable cap at the end for feeding pea gravel all as specified(Cost of gravel feeding is not included in this item ). |
| 85 | Supplying and fixing strata sample box made out of II class hard wood (hillock) with openable transparent glass shutter 3mm thick and locking arrangements, having not less than 20 compartment capable of holding 400 to 600gms of strata sample including painting wooden surfaces with two coats of synthetic enamel paint (grey)over a coat of pink primer complete all as directed. |
| 86 | Yield testing and stabilizing of the tube well by means of pumping by air compressor to obtain a minimum desire yield of 30000GPH for number of hours as required :-(a)By compressor of capacity suitable PSI 500 to 600 upto first 2 hours so that clear water is obtained for continuous out put of 30000 GPH. (b)For subsequent hour by compressor of capacity suitable PSI for 24 hours to 42 hours.(c)Yield testing of the tube well by means of electric driven pumping set of suitable capacity (The discharge shall be measured by providing orifice system of ‘V’ Note fixed to steel tank of adequate capacity) |
| 87 | Supply, Install, testing & commissioning factory made outdoor type dust and vermin proof LT panel board cubical double door hinged type compartmentalized of suitable size 415 volts, AC 50 Hz fabricated of CRCA sheet 3.15 mm thick machine pressed and angle iron frame 40 mm x 40mm x6mm grouted in PCC 1:2:4 type B1 (20mm graded stone aggregated) powder coated inside and outside complete including 4 pole copper bus bar of capacity 200 Amps (size 25mm x 6mm) mounted on porcelain insulators and enclosed in chamber and connection from incoming and outgoing electric cable with suitable size thimbles/lugs with open able shutters on both side and comprising of the following :-(a) Incoming MCCB 160 Amps cap with adjustable thermal release 4 pole of 25 KA rupturing capacity- 01 No.(b) OutgoingMCCB 100 Amps cap with adjustable thermal release 4 pole of 25 KA rupturing capacity - 01 No. (c)outgoing MCCB 32 Amps cap with adjustable thermal release 4 pole of 25 KA rupturing capacity - 01 No.(d) Digital Volt meter 0-500 volt with built in line & voltage selector switch, Digital Amp meter of capacity 0-100 Amp bolt in line current selector switches type indicator (RYB), 3 x 100/5 tape wound CT\"s 3 x SP MCBs of 6 Amp for protection of indicator. Size of voltmeter & ammeter to be 96sqmm. -01 Job.(e) Electronic Energy meter 3 phase, 0-200 Amps including set of CTs- 1 Nos. f) Fully automatic star delta starter suitable for 50 HP, 415 volts, 50 submersible pump set AC electric driven - 01 No. g) Single phase preventer - 01 No.h) Change over switch four pole 200 Amp with 50 Hz -01 No. i)Automatic phase corrector 3 Phase, 415 volt 50 Hz AC supply suitable for motor of 50 HP capacity- 01 Set |
| 88 | Supplying, lowering, installing, commissioning and testing of submersible pumping set of capacity 1000 LPM at 100 metre head with outlet size 100mm bore including electric motor AC3 Phase, 400-440 volt, 50 C/S submersible not less than 40 HP capacity with the following accessories :-(a) Submersible cable PVC ofcopper conductor of size 16 Sqmm 3core two lengths of required length from panel to star delta starter and motor of submersible Pumping set installed not less than 60 metre below ground level.(Make of the pump Crompton,Havells or Kirloskar) |
| 89 | Supply, lowering and jointing MS coloumn heavy duty flanged pipe 5.4mm thick 100mm bore conforming to IS -1239 (part-I) of 1979 (length not less than 3mtr each) MS flanged not less than 15mm thick on both side, with drilled holes and welded to MS pipe, including material and labour for jointing material with nuts, bolt, rubber packing complete all as specified and directed. |
| 90 | S&F non return valve CI heavy duty 100mm dia double flanged incl rubber gasket nuts and bolts comp for jointing all as specified and directed. |
| 91 | S&F sluiced valve 100mm bore ISI marked conforming to IS 14878 class PN 1.6 with brass spindel ,checknut , fibre gasket ,washer nuts and bolt comp all as specified |
| 92 | MS chain double for holding motor and fix to strong hook at GL level |
| 93 | Supply, laying, connecting and testing 150 mm bore, ductile iron pipes tyton joint class K-9 suitable for including rubber joint in standard working length conforming to IS 8329 laid in trenches complete all as specified and directed. |
| 94 | M&L for Ductile special fitting such as bends,tapers.tee pieces(single and double branch) any type and angle/radius and straight connecting pieces but all end flanged complete all as specified and directed . |
| 95 | Flate Flexible copper cable 3 core 16 Sq.mm |
