Tender For Addn/Altn To Gdcc Bldg At Swac And Bldg No P- 232 At Vsn Chiloda Under Ge (Af) Chiloda; 1 Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed. 2 M & L hardcore of broken bricks of gauge n.exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface complete all as specified and directed. 3 M&L 100 mm thickPCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base complete all as specified and directed. 4 M&L 80mm thick, machine pressed precast concrete interlocking paver block, with grey cement and pigment,any shape and size confirming to IS 15658-2006, M-40 Grade laid over and including 25mm thick layer of sand cushioning and filling the interstices etc with sand complete all as specified and as directed. 5 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. 6 Excavation in post holes each n. exc. 0.50Cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. ex`c. 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surface complete all as specified and directed. 7 M&L forPCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation of columns,building pillar,posts,struts,etc. filling and mass concrete complete all as specified and directed. 8 S&F in steel work in tubular trusses including special shaped washer,as in purlin / rafter, ms plate and connecteing works etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed. 9 S&F for mild steel plates (plain or chequered) of Grade Fe 410-W, (Gde- E-250) quality-A as inconnectingplates, base plate etc.welding etc complete all as specified and directed by Engr in Charge 10 S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. 11 M&L forpreparation of steel surfaces of any description over 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed by Engr-in-Charge. 12 S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed. 13 S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed. 14 S&F powder coated anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators, partition with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 15 S&F powder coated, any colour, aluminum door shutters (minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 Kg/ Sqm including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door, tower bolts, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed. 16 M&L 12 mm thick prelaminated partical board, interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to timber frame work or inserted in aluminium frame work complete all as specified and directed. 17 S&F aluminum alloy door closer hydraulically regulated, desination No 3 universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 Kg and fixed to door frame complete all as specified and directed. 18 M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed. 19 S&F 100 mm size mortice lock of brass, vertical type,4 levers, complete all as specified and directed. 20 S&F door stopper of aluminum alloy body and tongue anodised with rubber shoe fixed to door with screws complete all as specified and directed. 21 Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting outsoft and loose soil complete all as specified and directed. 22 Excavating in trenches, additional 1.5m or part thereof in depth beyond the first 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. and getting out soft and loose soil complete all as specified and directed. 23 Returning filling in including spreading, levelling,watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed. 24 Removal of surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point and disposal complete all as specified and directed. 25 M & L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete etc complete all as specified and directed. 26 M & L for Brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius ,built in CM 1:6 complete all as specified and directed. 27 M & L Brickwork with fly ash Bricks, straight or curved on plan to any radius in Half Brick thick walls, built in Cm (1:4) complete all as specified and directed. 28 M&L for rendering 10mm thick plaster in CM 1:6 on fair faces of brick work or concrete surfaces of walls finished even & smooth with out using extra cement work complete all as specified and as directed. 29 M&L for rendering 15 mm thick on brick or concretesurfaces in cement mortar (1:4) finished even & fair without using extra cement work complete all as specified and as directed. 30 M & L 5mm thick rendering in Cement Mortar 1:3 on fair facesof brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and as directed. 31 M&L for preparing new surfaces of ceiling and applying three coat of white wash complete all as specified and as directed. 32 M&L two coat of oil bound distemper onPreparaion plastered or unplasterd surfaces over a coat of alkali resistance primer on vertical surfaces of walls , and the like complete all as specified and as directed. 33 M & L applying two coats of cement based paint on newly plastered or unplastered wall surface including preparation ofsurfaces, complete all as specified and directed. 34 M&L for formwork to sides of concrete foundations, footings, bases of columns, rafts raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or batter, finished rough surfaces of concrete, complete all as specified and directed. 35 M&L for formwork to fair finish surfaces soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. 36 M&L for formwork to fairfinish surface edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. 37 M&L for formwork to sides and soffits of lintels,lintel bend, beams etc finished rough surfaces of concrete complete all as specified and directed. 38 M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular finishes rough surfaces of concrete.etc finished rough surfaces of concrete complete all as specified and directed. 39 M&L RCC M-25 Design Mix, using 20 mm graded aggregate as in beams, cantilevers, lintels, over 1.5 m span complete all as specified and directed. 40 M&L RCC M-25 Design Mix, using 20 mm graded aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed. 41 M&L RCC M-25 Design Mix, using 20 mm graded aggregate as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and directed. 42 M&L RCC M-25 Design Mix using 20 mm graded aggregate as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified and directed. 43 S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. 44 S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia complete all as specified and directed. 45 M&L for 16-18mm thick granite (of any type/ colour) work (table rubbed and polished) for steps ,jambs ,pillars ,window cill andwall lining (veneering to wall) 12mm thick in cement mortar (1:3)or chemical adhesive including pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-charge. 46 M&L 75 mm thick cement concrete type C1 1:3:6using 40 mm gradedstone aggregate as in plith protection, surface finished even and smooth without using extra cement complete all as specified and directed. 47 Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame, complete as specified by the manufacturer and as per directions of Engineer-in-charge. 48 Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. 49 S & F 100 mm long butt hinges extruded alumiunium alloy with galvanised mild steel hinges pin, anodised and fixed complete all as specified and directed. 50 S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing boltsand sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. 51 S & F 150 mm long aluminium anodised barrel tower bolt of extended section and fixed complete all as specified and directed. 52 S & F 125 mm long aluminium handle cast type anodized complete all as specified and directed. 53 Treating The Backfill In Contact With Foundation At The Rate Of 7.5 Litres Of Emulsion Per Square Metre Of Vertical Surface (area Of The Sub Structure In Contact With Backfill To Be Measured) complete all as specified and directed. 54 Treating The Top Surface Of Filled Earth At The Rate Of 5 Litres Of Emulsion Per Square Metre Of Surface complete all as specified and directed. 55 Treating The Soil Along With External Perimeter Of Building At The Rate Of 2.25 Litre Of Emulsion Per Metre Of The Perimeter Wall complete all as specified and directed. 56 Treating The Soil Under Plinth Protection At The Rate Of 5 Litres Of Emulsion Per Square Metre Of Surface Area complete all as specified and directed. 57 M&L for Glazed ceramic coloured tiles in vertical surface of size 450mmX 300mmX 7mm / 600mm x 300mm x 7mm thick joint free set and jointed in neat cement slurry and pointed in white or colour cement to match including backing coat of 10mm thick in CM (1:4) complete all as specified and as directed. 58 M&L for Non - skid ceramic colouredtiles 10 mm thick joint free area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. 59 M&L 25 mm thickcement concrete type B-1, 1:2:4 using 20mm graded stone aggregate as in floors levellingfor tiles complete all as specified and as directed. 60 Demolition of brick work built in cement mortar or cement lime mortar complete all as specified and as directed. 61 S&F stainless steel kitchen sink with drainage board of overall size 915x460mm and bowl size 410x330x160mm with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as specified and directed. 62 S&F 15 mm size sink cock (wall mounted) with long swivel spout and wall flange with all connected accessories, complete all as specified and directed.Make : Cat part No F1015251 of CERA or techno commercially equivalent as approved by GE. 63 S&F stainless steel plate rack , 0.5mmto 1mm thick having size (900 x 760 x 230 mm ) including fixing on wall with brackets etc complete all as specified and as directed. 64 Material and labour for providing kitchen cabinet and cubboard in required sizes at site made out of 18mm thick PVC sheet (prelam) having one side decorative laminated sheet (for shutter, sides of cabinet, partition and shelves etc). All the edges of shutter and front exposed edge of partition/shelves shall be covered with 2mm thick edge bonding tape as per manufacturer. Including all required fixing material such as SS brackets, screws, adhesive etc., complete all as specified and as directed by Engineer-in-charge.Note :- (i) The area of each sheet (shutter, sides of cabinet, partition and shelves)shall be measured in sqm for payment.(ii)Magnetic catcher, handles, continuous Piano hinges and PVC frame (where required) shall be measured and paid separately under appropriate item of BOQ.(iii) Any other material required for making/fixing/hanging of cabinet shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. 65 S & F continous (Piano)type hinges stainless steel bright finish or lectro galvanised with wide of flaps30mm complete all as specified and directed. 66 S&F stainless steel fancy type handles ofsize 75 mm complete all as specified and directed. 67 S&F Magnetic catches of size25 mm x 12mm, No.3, complete all as specified and directed. 68 S&F Chlorinated PVC (CPVC) pipes 20 mm outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.0 m spacing . this includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed. 69 Supply & fixing mild steel tubes of size 25 mm bore (medium grade) galvanised with all fittingsand fixed to wall complete all as specified and directed. 70 S&F 110mm PVC (SWR) pipes single socketed(pressureratingnotlessthan 4kg/sqcm)in any length with rubber ring joints laid in trenches or in floors / walls fixed withand including PVC clamps, complete all as specified and directed. 71 S&F 75mm PVC (SWR) pipes single socketed(pressureratingnotlessthan 4kg/sqcm)in any length with rubber ring joints laid in trenches or in floors / walls fixed withand including PVC clamps, complete all as specified and directed. 72 S&F PVC (SWR) 40 mm borepipes, single socketed in any length with rubber ring joints with adhesive solvent fixed to wall or flooras in urinal/ WHB waste water line and similar works etc complete all as specified and directed. 73 Supply&fixingPVC(SWR)bends(anyradius)suitablefor110mmborepipecompleteallas specified and as directed by Engineer-in- charge. 74 Supply&fixingPVC(SWR)bends(anyradius)suitablefor75mmborepipecompleteallas specified and as directed by Engineer-in- charge. 75 Supply&fixingPVC(SWR)bends(anyradius)suitablefor 40mmborepipecompleteallas specified and as directed by Engineer-in- charge. 76 Supply&fixingPVC(SWR)floortrap,plainwithgrating,suitablefor100/75mmborepipeincluding jointing with solvent cement complete all as specified and as directed by Engineer-in- charge. 77 Supply and fixing PVC (SWR) reducer 110/75 complete all as specified and as directed by Engineer-in-charge. 78 Supply & fixing PVC (SWR) vent cowl suitable for 75mm bore PVC pipe complete all as specified and directed. 79 Supply & fixing PVC (SWR) of size 110 mm sanitary connection socket to fit out let of WC complete all as specified and directed by Engineer-in-Charge. 80 Supply & fixing 110mm bore PVC (SWR) junction single (single T) equal or unequal fixed with solvent cement, with access door complete all as specified and directed. 81 Supply & fixing 75mm bore PVC (SWR) junction single (single T) equal or unequal fixed with solvent cement, with access door complete all as specified and directed. 82 Supply & fixing 40mm bore PVC (SWR) junction single (single T) equal or unequal fixed with solvent cement, with access door complete all as specified and directed. 83 M & L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. 84 M & L PVC (SWR) multi floor trap 75mm/100mmwith grating including jointing with solvent cement complete all as specified and directed. 85 Supply&fixing150mmborePVC(SWR)pipessinglesocketed(pressureratingnotlessthan 4kg/sqcm)inanylengthwithrubberringjointsfordrainorrainwaterfixedalongwallswithand including PVC clamps complete all as specified and directed. 86 Supply&fixingPVC(SWR)bends(anyradius)suitablefor150mmborepipecomplete all as specified and directed. 87 S & F 600 x 450 mm size beveled edge mirror 5mm thick of selected quality glass mounted on 6mm thick commercial plywood and fixed with wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 88 S&F table top wash basin with fixing accessories of size 550mm x 400mm x 140mm complete all as specified and directed. Make : Cera Cat Part No. S2020137or techno commercially equivalent as approved by GE. 89 S&Fsingle piece WC with slim soft close seat cover ,cistern fittings, fixing accessories and accessories set of size 655mm x 345 mm x 750mm, with S trap 220mm complete all as specified and directed. Make : Cera Cat part No S1013205 or techno commercially equivalent as approved by GE. 90 S&F in repair urinals without sensor (back inlet) with all fixing accessories of size 265 x 335 x 695mm complete all as specified and directed. Make : CERA Cat part No S4020116 or techno commercially equivalent as approved by GE. 91 S&F in repair urinal flush valve concealed push type (single flush ) 32mm ofchromium plated for fixing with 15 mm dia pipe complete all as specified and directed. Make : CERA Cat part No F8010108 or techno commercially equivalent as approved by GE. 92 S&F in repair bib taps long body, 15mm bore dia, fancy type, cast copper alloychromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed. 93 S&F 15 mm size two way bib cock with single handle and wall flange cast copper alloy, chromioum plated with fancy type screwed down, with capston head, screwed for iron pipe complete all as specified and as directed. Make : Cat part No F2002163 of CERA or techno commercially equivalent as approved by GE. 94 S & F in repairs 15mm bore CP Angle cock one waychromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed. 95 S&F in repairs 25 mm size gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and gate valve complete all as specified and directed. 96 S&F in 15 mm size pillar cock with swan neck spout(Left / right) and aerator fancy type cast copper alloy chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed. Make :CERA Cat part No F2014104 or techno commercially equivalent as approved by GE. 97 S&F in repair PVC connection 15 mm size with PTMT nuts on both end, length 600 mm, complete all as specified and directed. 98 S&F brass chromium plated bottle traps for wash basinsand urinal with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed. 99 S&F stainless steel grating doom 150 x 150mm complete all as specified and directed. 100 S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. 101 S&F toilet paper holder with stainless steel wall flange complete all as specified and directed. Make : Cera Cat part No F5015109CH or techno commercially equivalent as approved by GE. 102 S&F towel ringwith stainless steelwall flange complete all as specified and directed. Make : CERA Cat part No F5013115CH or techno commercially equivalent as approved by GE. 103 S&F soap dispensor with glass bottle complete all as specified and directed.Make : CERA Cat part No F5012111CH or techno commercially equivalent as approved by GE. 104 S&F soap dish (Glass) holder with wall flange complete all as specified and directed. Make : CERA Cat part No F5013116CH or techno commercially equivalent as approved by GE. 105 S&F 1000 Ltrs capacity rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoistedand fixed on roof in position over existing PCC platform including all fitting such as connection pipe pieces with GI tank nipple for inlet, outlet,washout and overflow etc and including fixing only ball valvescomplete all as specified and directed. 106 M&L ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 210 gm screwed for 25mm bore iron pipe supplied and fixed in repair complete all as specified and directed by Engineer-in-charge. 107 M&L for ATT Along the internal and external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes minimum 300mm depth @ 300mm c/c etc in apron complete all as specified and as directed. 108 M & L for Anti-termite treatment of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and pluging 12mm dia hloles with cement mortar 1:2 (1cement: 2 coarse sand) tyo match the existing floors complete all as specified and directed. 109 Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe complete all as specified and directed. 110 M&L precast RCC 1:2:4 type B1 as in landings, cover slab ( (for man holes etc.) chullah hoods, water troughs, mangers, shelves and,chajjas etc.and similar articles with plain faces set in CM 1:4 complete all as specified and directed. 111 M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm dia pipe complete all as specified & directed. 112 M&L for cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills,steps,and other similar bands,plinth courses, string courses, lacing courses, parapets and railing upto 60cm eight,copings,kneelers,apex stone,bed plates and the like including weathering slightly rounded or chamfered angles and throating, complete all as specified & directed. 113 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 114 Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. 115 Dismantling of stone slabs & tiles of anythickness & in any position laid, bedded and pointed in any mortar otherwise complete all as specified and directed. 116 Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exc 1.5 sqm but n exc 4.00 sqm each complete all as specified and directed. 117 Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n exc 1.5 sqm each complete all as specified and directed. 118 M&L for anodised aluminium snap grid frame work of size (605mm X 605mm ) using T grid/Cross-T/Wall angle/level clip & suspenders for false ceiling and similar works including hangers 6mm dia. G.I. wire (upto 1200 mm length) size of grid (605 mm X 605 mm ) adjusting level fixed to roof slabs/trussesby means of ceiling cleats made out of G.I.flat 40 x 3 mm size 60 mm long and expansion hold fastener 12.5mm dia 40mm longcomplete all as specified and directed by Engineer-in-charge. 119 S & F false ceiling 8 to 10mm thick gypsum tiles (600mm x 600 mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film fixed complete all as specified and as directed by Engineer-in-Charge. 120 M&L forVitrified Ceramic tiles 10 mm thick, light shade(square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match premium quality as in floor etc andincluding screed bed 15 mm thick in CM (1:6) complete all as specified and directed. 121 All as per item No 120 here in before but on vertical surfaces/skirting including backing coat 10mm thickin CM (1:4) complete all as specified and directed. 122 M&L for aluminium powder coating (powder coated of required colour) three track sliding windows frame top and sides of size 92x31.75x1.5mm (section No 20831), bottom size 92x31.75x1.5mm (section No 20832) and shutter top & bottom of size 40x18x1.55mm (section No 20736) and sides (handle) of size 40x18x1.55mm (section No 20738) and lock side shutter frame of size 40x18x1.45mm (section No 20737) with rubber gasket beading and locking arrangement and rollers etc including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperature and fixed with stainless steel wire staples and fixing 5mm thick glass (plain/tinted/with laminated film) incl necessary rubber beading gasket complete all as specified and as directed. 123 M&L for cement concrete Type B0 1:2:4 (12.5mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed. 124 S&F 5.5 mm thick glass, looking mirror size exc 0.5 Sqmandnot exc 3 sqm of selected quality glass, mounted on 10 mm thick commercial ply or plane with decorated beading all round of woodwith chromium plated brass screws/ brackets/ studs in top and bottom etc complete all as specified and directed. 125 S&F for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. and similar small articles conforming to Fe 410 W (Grade E-250 ,quality A ) complete all as specified and as directed. 126 M&L 15mm thick Italian Marble tiles slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, shelves, WHB platform in any position in cement mortar (1:4) and pointing with white or coloured cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 127 S & F pre painted galvalume aluminum Zinc coating GI based plain steel sheeting 0.5mm thick of any colour having tensile strength of 550 MPA as in ridge ,gutters etc fixed with self tapping screws complete all as specified and directed. 128 S&F for manually operated zebra blinds for flexible light control and privacy having opaque strips aligned to block light with alternate horizontal strips of sheer and opaque fabric or polyster of size as per requirement width and drop, having hardware top tube made of extruded aluminium with spline adoptable to accomodate clutch moulded plastic having self lubrication with glass fibre reinforcementhaving a minimum lifting capacity head adoptability operating chain plastic/steel ball chain adoptable to the clutch pitch for smooth operation of blinds locking member plastic/steel stop locks for limit setting adoptable to be steel chain bonding with wide double sided adhesive tape of reqd length for strong holding capacity spring booster provided as per the requirement bottom bar aluminium extruded circular section with powdwer coated finish, for a perfect fall to fabric to avoid warpage/floating ends are covered with ends cap to give a perfect finish complete all as specified and directed. 129 Taking down cement or cement lime plaster from brick walls etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed. 130 M&L for complete removal of old treatment of old surfaces of wall by brooming down or steel wire brushing, scrapping down smoke, efflorescent salts, oil, greesy spot or peeled off surfaces and applying a layer of Birla white putty 2mm thick even and smooth and applying two coats of plastic emulsion paint (approved quality & tint) over a coat of alkali resistant primer using painting rollar complete all as specified and directed. 131 Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified anddirected. 132 S&F for Toughned sliding glass 12mm thick as in partition/hinged doors/automatic doors and similar work including cutting to shape, grinding, drilling holes, SS studds for fixing complete all as specified and directed 133 M&L for Preparation of old steel painted surfaces of any description exc 10 cm width or girth and appying one coat of synthetic enamel paint, complete all as specified and as directed. 134 Taking down carefully copper/ aluminum point wiring (Light, fan, socket, power and Bell) including fixture and fittings such as switches, sockets, ceiling roses, lamp, holder , regulators, socketslight fittings etc , removing material to store for keeping in safe custody or for taking credit , and making good disturbed surface of walls, floors, etc. complete all as specified and directed by Eng-In-Charge. 135 M&L for point wiringfor modular accessories with modular metal flush box and cover plate with frame of suitable size complete with 1.5 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLScable 1100 volts grade drawn throughmetallic rigid / PVC heavy duty concealed conduit/ casing capping/open coduit with 1.5 sqmm, single core, PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 volts grade as earth continuity wire terminated in new modular sunken boxes and modular metal flush box as required size at site incl all connected accessories , box made from not less than 1.6mm GI sheet factory made complete all as specified and directed by Eng-In-Charge for the following. (a)One light/fan/bell pointcontrolled by one switch One light/fan pointcontrolled by one switch complete 136 All as per item No 135 here in before but one 3 pin socket out let 5 Amps on the independent board. 137 All as per item No 135 here in before but one 3 Pin socket out let 5 Amps on the same board. 138 All as per item No 135 here in before but with cable of size 2.5 Sq mm PVC insulated on independent boardfor power plug 5/15 Amps. 139 All as per item No 135 here in before but with cable of size 4 Sq mm PVC insulated on independent boardfor power plug 15 Amps. 140 S&FModular switch one way 6A, 1 Module complete all as specified and directed. 141 S&F Modular switch one way 16A, 1 Module, complete all as specified and directed. 142 S&FModular socket 6/10A-2/3 pin combined 2 Module complete all as specified and directed. 143 S&F Modular socket 16/15A-2/3 pin combined2 Module complete all as specified and directed. 144 M&L sub main wiring complete with PVC insulated cable two run of06 Sq mm (FRLS) 1100 volts grade with multi stranded copper conductor for drawn through and including PVC casing -cappingwith accessories incl6 Sq mm unsheathed multi stranded copper conductor as on earth wire complete all as specified and directed by Eng-In-Charge.Note :- Two runs of 4 sqmm cable with one run of earth continuity cable including PVC casing -capping and its accessories will be measured and paid as one unit 145 S & Fsheet metal enclosure, single phase, double door DB, flush to wall mounting for MCB fitted with 200 Amp ratedbus barsand neutral links ( without MCBs) 8 ways SPN complete all as specified and directed. 146 S & F MCB, SPN 240 volts, 40 to 63 Amps capacity complete all as specified and directed. 147 S & FMCB, SP 240 volts capacity 5 - 32 Amps current rating, 10KA breaking capacity complete all as specified and directed. 148 S & Fin repair Pluto Panel surface/recess mounted2x2 ,36-40 watt cool white or warm white in colour LED flat panel for surface mounting which provides soft-light and glare free symmetrical illumination including connection up with twin core twisted flexible copper conductior cable with suitable size complete all as specified and directed. 149 S&F wall fan complete with accessories, 230 V, 400 mm sweep. Five star rated with complete all as specified and directed. 150 Supply install high wall split type air conditioner unit indoor/out door complete with cordless remote control unit and with in built air ioniser and plasma filter for batter indoor air quality and EER 3.2 of cap 1.5 ton inverter type 5 star of make complete all as specified and directed.Note: Contractor will be resposible to brought extra copper pipe and drain pipe where ever required, extra copper pipe and drain pipe will not be paid extra. 151 S&Fin replacement ceiling rose 3 terminal/ poly carbonate, isolated body complete all as specified and directed. 152 S & Fin replacement white cover plate with frame , 3 module complete all as specified and directed. 153 S & F in replacement white cover plate with frame , 4 module complete all as specified and directed. 154 S & Fin replacementwhite cover plate with frame , 6 module complete all as specified and directed. 155 S & Fin replacement white cover plate with frame ,8 module complete all as specified and directed. 156 S & Fin replacement white cover plate with frame ,12 module complete all as specified and directed. 157 M&L for Sub main wiringin replacement complete with two run of10 Sqmm single core, PVC insulated but unsheathed, multistranded copper conductorFRLS 1100 Volts grade cable drawn through in and including non metallic, rigid, PVC heavy duty surface conduit/casing capping (ISI marked) with wall thickness not less than 1.8mm complete with all accessories like bends, tees, junction boxes fixed on wall, ceiling and incl sunken type pressed steel terminal boxes with 3mm thick bakelite white/coloured (as approved) top cover including 10 Sqmm single core PVC insulated but unsheathed multistandard copper conductor FRLS 1100 Volts grade cable as earth continuity wire and connected to earth dolly . Note :-Two run of 10 Sqmm cable incl one run of earth wire and PVC conduit and its accessories shall be measured and paid as one length complete all as specified and directed. 158 Supply and fixingin replacement TPNdouble door DB 4 way incl civil work complete all as specified and directed. 159 Supply and fixingin replacement sheet metal enclosure, single phase, double door DB, flush to wall mounting for MCB fitted with 200 Amp ratedbus barsand neutral links ( without MCBs) 12 ways SPN complete all as directed by Engineer-in-Charge. 160 S & F in replacement of single pole and neutral sheet metal enclosure with atwo Pin Socket plug and socket with one single pole MCB 240Volts, 20 Amps, capacity complete all as specified and directed by Engineer-in-Charge. 161 S & F in replacement MCB, TPN 415 volts,63 Amps capacity complete all as specified and directed by Engineer-in-Charge. 162 S&Fin replacementdecorative wall mounting/Surface mounted round spot/focus light/mirror light CRCA body powder coated in white of capacity 10 wattcomplete all as specified and directed by Engineer-in-Charge.
