Supply Installation Testing And Commissioning Of Lift Along With Related Electrical Works At Integrated Office Building,Cooch Behar, Coochbehar-West Bengal

supply installation testing and commissioning Of Lift Along With Related Electrical Works At Integrated Office Building,Cooch Behar= 1 SITC of Automatic Lift( as per manufacturer design & as per detailed specification below conforming to IS ) and putting into operation afterfinal testingin the existing liftshaftcomplete with all accessories andrepairing thedamage wall / floor/or any civil work if any etc to complete as required. 2 Make : Categary-I- OTIS / KONE/SCHINDLER 3 Type:Bed Cum Passanger Lift. 4 Load : 13 Passenger / 884 Kg 5 Control: Microprocessor based with AC variable voltage & variable frequency( VVVF) 6 Machine:- Energy efficient machine, Gearless without MachineRoom 7 Position of Machine Room: MRL 8 Speed: 1.0 Mtrs./ Sec 9 Floor served: G + 3 10 Landing: 4 , all on same side 11 Total Rise: 10.8 m 12 Operation: Microprocessor based simplex fullcollectivewith or without attendant. 13 Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator. 14 Traveling accuracy:± 5 mm(Micro levelling arrangement ) 15 CAR 16 Car inside :1600 mm wide x 1350 mm deep x 2200 mm high 17 Door Dimension: 900 mm wide x 2000 mm internal height 18 Car Enclosure: Stainless Steelsheet (20 SWG) with Hairline finish withhand rail. 19 Car Ceiling & Lighting: Stainless Steel with hairline finish with LED lighting andFan 20 Car Ventilation: Pressure fan with anodised aluminium grill. 21 Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Departments Order). 22 Car Door:Stainless Steelcentre opening/Telescopicautomatic door providedwith V3F controlled door drive system 23 Landing Door: Stainless steel centre openingautomatic door providedwith V3F controlled door drive system 24 Door type: Two-panel to Center opening 25 Door Opening: Automaticpower oprated door with full length Photocell assembly light curtain sensor 26 PROTECTIVE DEVICES & OTHER ACESSORIES 27 ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others. 28 Overload Protection:Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and giveaudiodisplay indication 29 Emergency lighting in car: Battery operated emergency lighting in the lift car. 30 Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room 31 Emergency Alarm: Battery operated alarm bell system in lift car and control room 32 Fireman switch: Fireman switch at main landing terminal. 33 Voice Synthesizer: Voice announcementsystem (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. 34 Main rope - As per manufacturers standard conforming to IS 35 DIMENSION OF SHAFT & POWER SUPPLY 36 Available Shaft Dimension:2300 mm width and 2300 mm depth 37 Pit Depth :1350 mm 38 Overhead : 4200mm 39 Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS 40 Note: 1) Rates should be quotedwith minor civil works, wall cuttingand mending good the damages to the original finish. 2) All the above rates should be quoted inclusive of all taxes & duties, District charges and LWC as applicable, with cost of maintenance, servicing,supply & replacement of spares for 01 (One) year from the date of commissioning.3) The Agency must procure the materials from the manufacture/OEM or their authorised sales Channel so that the standard warranty/support of the manufacturerer/OEM becomes applicable to the product to be delivered and installed by them. Documents that authenticate such procurement from the manufacturer/OEM or from their authorised sales Channel and standard warranty/support should be sent from the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution of work/submission of bill. If any refubrished materials are supplied and installed, penal action will be taken as per existing rule. Before execution of the work the prospective bider has to submit layout drawing as per design of OEM dully approved by the OEM. 4) Total is rounded off to the nearest rupees

Sr No	CorrigendumDate	Corrigendum	CorrigendumType	NewSubmissionDate
1	13-10-2025	DATE CORRIGENDUM 1	Date	07-11-2025

Refer document

INR 17.51 Lakhs /-

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB