|
| 1 | FOR PART A |
| 2 | Supplying and filling in plinth withsand under floors, including watering, ramming, consolidating and dressing complete. |
| 3 | With stone dust by truck carriage including loading and unloading to the site of work |
| 4 | Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 5 | Plain Cement concrete floor base in proportion 1:3:6 laid in alternate bays as specified with coarse aggregate of size 13mm to 32mm including dewatering if necessary and curing etc. complete. |
| 6 | 50 mm thick |
| 7 | Cement concrerte works in topping 1:1:2 on RCC floor, tread and rise of steps, kitchen slab etc finished with a floating coat of neat cement using cement slurry for bond @ 2.75 kg of cement per sqm of floor to be laid in panels including curing complete as directed. |
| 8 | 20mm thick |
| 9 | 25 mm thick cement concrete topping 1:2:4 finished with a floating coat of neat cement slurry to be laid in panels including curing complete as directed. |
| 10 | SURFACE PREPARATION :Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels. |
| 11 | Extra for Old Building Repairs over Item No. 8.13, for removing and chipping of brick bat corba, tar felt or any other existing protective layer over roof slab etc. |
| 12 | Providing and fixing ISI marked flush door shutter conforming to IS:2202 (Part-I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutter: |
| 13 | 35 mm thick including ISI marked stainless steel butt hinges with necessary screws. |
| 14 | Satna lime wash on walls with one coat. |
| 15 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour |
| 16 | Old works (One or more coat) |
| 17 | Applying priming coat over new wood and wood based surfaces over 100 mm in girth / width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. |
| 18 | Applying priming coat over new wood and wood based surfaces over 100 mm in girth / width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. |
| 19 | With ready mixed paint , wood primer |
| 20 | Painting one coat (excluding priming coat) on old wood and wood based surface with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matters sand papering and stopping. |
| 21 | (i) Surfaces over 100mm in width or girth. |
| 22 | General purpose(Asian/Berger/ICI/J & N / Nerolac paint) |
| 23 | ii) Surfaces upto 100mm in width or girth. |
| 24 | General purpose(Asian/Berger/ICI/J & N / Nerolac paint) |
| 25 | Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufactirer to give an even shade including cleaning the surface of all dirt, dust and other foreign matters sand papering and stopping. |
| 26 | (ii) Surfaces upto 100mm in width or girth. |
| 27 | General purpose(Asian/Berger/ICI/J & N / Nerolac paint) |
| 28 | Applying priming coat over new steel and other metal surface up to 100mm in width or girth after preparing the surface by thoroughly cleaning oil, grease, dirt and dust and other foreign matters and scoured with brushes, fine steels, wood scrapers and sand papers |
| 29 | a)With ready made mixed red-lead/ red oxide primer. |
| 30 | Finishing walls with water proofing weather coat paint of required shade : |
| 31 | Old work (one or more coats @ 2.20 kg/10 sqm) complete. |
| 32 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 33 | 300x16 mm |
| 34 | 250x16 mm |
| 35 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 36 | Single rubber stopper |
| 37 | Providing and fixing plain frosted glass of ordinary quality beded in putty and fixed with/ without wooden bidding including necessary cutting and glass to be required sized ( paymentfor wooden bead shallbe made seperately). (1) Area of glass panes not exceeding 0.15 sqm. |
| 38 | 3.5 mm thick |
| 39 | Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. |
| 40 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : |
| 41 | Of sectional area below 40 square centimetres |
| 42 | Dismentling All types of ceiling, partition and wall lining and stacking the materials as directed by the department for all levels. |
| 43 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 44 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete. |
| 45 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete. |
| 46 | White solid plastic seat with lid |
| 47 | Providing, fitting & fixing Chrome Plated robe hook complete as directed & specified. (a) Jaquar Make |
| 48 | Continental |
| 49 | Providing and fixing PTMT Waste Coupling for wash basin and sink, ofapproved quality and colour. |
| 50 | Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms |
| 51 | Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms |
| 52 | Supplying, fitting & fixing 87.5 degree PVC bend of (Supreme / prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified.a) In exposed surfaces or in trenches |
| 53 | 110 MM DIA |
| 54 | 50 MM DIA |
| 55 | Supplying, fitting & fixing 87.5 degree PVC bend with door of (Supreme / prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches |
| 56 | 110 mm dia |
| 57 | Supplying, fitting & fixing PVC Plain single tee of (Supreme / prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches a) In exposed surfaces or in trenches |
| 58 | 110 mm dia |
| 59 | 50 MM DIA |
| 60 | Supplying G.I Fittings such as bend, tee, elbow, reducer, nipple, plug SOCKET etc. G.I Socket (ZOLOTO-m brand.) (Heavy) |
| 61 | 15 mm dia |
| 62 | 20 mm dia |
| 63 | G.I Reducing Socket. (ZOLOTO-m brand.) (Heavy) |
| 64 | 20mm x 15 mm size |
| 65 | G.I Elbow(ZOLOTO brand.) (Heavy) |
| 66 | 15MM DIA |
| 67 | 20 MM DIA |
| 68 | GI Nipple |
| 69 | 15mm dia |
| 70 | 20 mm dia |
| 71 | Providing and fixing PTMT bib cock of approved quality and colour |
| 72 | 15 mm nominal bore |
| 73 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 74 | 15 mm nominal bore |
| 75 | FOR PART B |
| 76 | Supplying and filling in plinth withsand under floors, including watering, ramming, consolidating and dressing complete. |
| 77 | With stone dust by truck carriage including loading and unloading to the site of work |
| 78 | Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 79 | Plain Cement concrete floor base in proportion 1:3:6 laid in alternate bays as specified with coarse aggregate of size 13mm to 32mm including dewatering if necessary and curing etc. complete. |
| 80 | 35 mm thick |
| 81 | 50mm thick |
| 82 | Providing Bamboo Scaffolding up to a height of 6.5 M including 2nd class timber plank platforms and removal of the same complete as directed & specified ( measurement to be taken on elevation area of the building / structure). |
| 83 | 25 mm thick cement concrete topping 1:2:4 finished with a floating coat of neat cement finish to be laid in panels including curing complete as directed |
| 84 | Providing 1.2 mm thick transparent fibre sheet ridging1.2 mm thick and 300mm lapping including supplying and fixing galvanised screws/ washers etc. complete as specified and directed |
| 85 | 2SURFACE PREPARATION :Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels. |
| 86 | Extra for Old Building Repairs over Item No. 8.13, for removing and chipping of brick bat corba, tar felt or any other existing protective layer over roof slab etc. |
| 87 | Providing and fixing ISI marked flush door shutter conforming to IS:2202 (Part-I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutter: |
| 88 | 30 mm thick including ISI marked stainless steel butt hinges with necessary screws. |
| 89 | Providing, fitting and fixing MS round bars with MS flat stiffeners at required spacing In wooden frames of windows and clerestory windows. |
| 90 | Satna lime wash on walls with one coat. |
| 91 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour |
| 92 | Old works (One or more coat) |
| 93 | Applying priming coat over new wood and wood based surfaces over 100 mm in girth / width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. |
| 94 | With ready mixed paint , wood primer |
| 95 | Applying priming coat over new wood and wood based surfaces over 100 mm in girth / width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. |
| 96 | With ready mixed paint , wood primer |
| 97 | Painting one coat (excluding priming coat) on old wood and wood based surface with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matters sand papering and stopping.(i) Surfaces over 100mm in width or girth. |
| 98 | (a) General purpose(Asian/Berger/ICI/J & N / Nerolac paint) |
| 99 | (ii) Surfaces upto 100mm in width or girthGeneral purpose(Asian/Berger/ICI/J & N / Nerolac paint) |
| 100 | Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufactirer to give an even shade including cleaning the surface of all dirt, dust and other foreign matters sand papering and stopping. (ii) Surfaces upto 100mm in width or girth. |
| 101 | a.General purpose(Asian/Berger/ICI/J & N / Nerolac paint) |
| 102 | Applying priming coat over new steel and other metal surface up to 100mm in width or girth after preparing the surface by thoroughly cleaning oil, grease, dirt and dust and other foreign matters and scoured with brushes, fine steels, wood scrapers and sand papers |
| 103 | With ready made mixed red-lead/ red oxide primer. |
| 104 | Finishing walls with water proofing weather coat paint of required shade |
| 105 | Old work (one or more coats @ 2.20 kg/10 sqm) complete. |
| 106 | Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges bright finished with necessary screws etc. complete |
| 107 | 100x58x1.90 mm |
| 108 | 75x47x1.70 mm |
| 109 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 110 | 250x16 mm |
| 111 | Providing and fixing aluminium handles, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 112 | 125 mm |
| 113 | 100 mm |
| 114 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 115 | Single rubber stopper |
| 116 | Twin rubber stopper |
| 117 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : |
| 118 | Of sectional area below 40 square centimetres |
| 119 | Dismentling Woodwork in frames of ceiling, partition etc. including disposal of debris and stacking of serviceable materials as directed complete. |
| 120 | Dismentling All types of ceiling, partition and wall lining and stacking the materials as directed by the department for all levels. |
| 121 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 122 | For thickness of tiles 10 mm to 25 mm |
| 123 | Demolishing Floor Topping (concrete/plastered) upto a maximum thickness of 20 mm without causing damage to base concrete including disposal of debris and stacking of serviceable material as directed complete. |
| 124 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 125 | Providing and fixing PTMT Waste Coupling for wash basin and sink, ofapproved quality and colour. |
| 126 | Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms |
| 127 | Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms |
| 128 | Supplying, fitting & fixing PVC Pipes of 6kg/cm2 (Supreme /Prince) or other ISI approved including joining, fitting and fixing with clamps etc. as necessary complete at all levelsincluding below G.L as directed and specified. a) In exposed surfaces or in trenches |
| 129 | 50 mm dia |
| 130 | Supplying, fitting & fixing 87.5 degree PVC bend of (Supreme / prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified.a) In exposed surfaces or in trenches |
| 131 | 110 mm dia |
| 132 | 50 mm dia |
| 133 | Supplying, fitting & fixing 87.5 degree PVC bend with door of (Supreme / prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. |
| 134 | 110 mm dia |
| 135 | Supplying, fitting & fixing PVC Plain single tee of (Supreme / prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified a) In exposed surfaces or in trenches |
| 136 | 110 mm dia |
| 137 | 50mm dia |
| 138 | Supplying G.I Fittings such as bend, tee, elbow, reducer, nipple, plug SOCKET etc.G.I Socket (ZOLOTO-m brand.) (Heavy) |
| 139 | 15 mm dia |
| 140 | 20 mm dia |
| 141 | G.I Reducing Socket. (ZOLOTO-m brand.) (Heavy) |
| 142 | 20mm x 15 mm size |
| 143 | G.I Tee (ZOLOTO-m brand.) (Heavy) |
| 144 | 15 mm dia |
| 145 | 20 mm dia |
| 146 | G.I Elbow(ZOLOTO brand.) (Heavy) |
| 147 | 15 mm dia |
| 148 | G.I Nipple |
| 149 | 15 mm dia |
| 150 | 20mm dia |
| 151 | 25mm dia |
| 152 | Providing and fixing PTMT bib cock of approved quality and colour |
| 153 | 15 mm nominal bore |
| 154 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 155 | 15 mm nominal bore |
