|
| 1 | Ring Well Excavation in foundation trenches not exceeding 1.50 m width or 10 Sq.m.on plan or drains not exceeding 1.50 m in width or 10 Sq.m. on plan including dressing of sides and ramming of bottoms, lift upto 1.50 m including getting out the excavated soil as directed,within a lead of50 m. (c) Hard Rock requiring chiselling (where blasting is probihited) |
| 2 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 3 | Providing and laying cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in : (b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level. |
| 4 | Centring and shuttering including strutting proping etc. and removal of form work for: (b) Walls including attached buttresses, pilasters etc |
| 5 | Bore Well Ground water exploration (Drilling by DTH-200 Rig mechine with ODEX option bore-well size 5\" (127 mm) and complete assembling with ERW casing pipe of size 128 mm ID and 142 OD and other required lubricants, accessories in the depth of approximately 100 mtr. |
| 6 | Provision for Jacket filter and other accessories(a) Jacket filter 80 mm dia and 3.00 mtr length each |
| 7 | (b) Packer assembly |
| 8 | © GI reducer 80 x 50 mm |
| 9 | (d) GI Socket 80 mm |
| 10 | (e) GI Nipple 50 mm dia |
| 11 | (f) End plug |
| 12 | Supplying and fitting 2 Horse power 1 pnase submersible pump made in cromption greaves discharge up to total head of 150 m with compartible to 40-50 mmdiameter pipe. |
| 13 | Supply of panel board with high quality |
| 14 | Supply of submersible cable 4 sqm copper |
| 15 | Supply of sfety wire |
| 16 | Supply of starter |
| 17 | Supply of GI pipe 40 mm x 3 mtr length filter with socket |
| 18 | Provision for 5\" bore-well size capacity clamp (2 Nos ) with nut & bolt |
| 19 | Septic TankEarth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 20 | Providing and laying in foundations and plinth cement concrete 1 : 3 : 6 (1cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 21 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cementmortar1:3(1cement:3finesand)ofthicknessnotexceeding6mmto give a smooth and even surface but excluding cost of centring and shuttering andreinforcementwithM20(1cement:1.5coarsesand:3stoneaggregate20 mm nominal size). |
| 22 | Centring and shuttering including strutting proping etc. and removal of form work for: ( a) Foundation, footings, bases of columns etc. and mass concrete |
| 23 | c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height) |
| 24 | Reinforcement of RCC work including bending, binding and placing in position complete. (b) Tar/ TMT steel |
| 25 | Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand) |
| 26 | 12 mm cement plaster 1 : 3 (1 cement : 3 fine sand). |
| 27 | Neat Cement Punning |
| 28 | Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and makingchannels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. (a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg). |
| 29 | Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design. |
| 30 | Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes. (a) 100 mm dia |
| 31 | SHToilet RoomEarth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 32 | Re-filling excavated earth in foundations and plinth etc. in15 cm layer including ramming and watering etc. complete |
| 33 | Filling in plinth with sand under floors including watering,ramming, consolidating and dressing complete |
| 34 | Providing and laying in foundations and plinth cement concrete 1 : 3 : 6 (1cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 35 | Providing and laying in foundations and plinth cement concrete 1 : 2 : 4 (1cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 36 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : (b)1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). (a) M20 (1 cement : 1.5 corase sand : 3 stone aggregate 20 mm nominal size) |
| 37 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement ((b)1 : 1.5:3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 38 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. ((b)1 : 1.5:3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 39 | Reinforced cement concrete in suspended floors, roofs, landings and balconiesupto floor two level including finishing and plastering the exposed surface with cement mortar 1:3 (1 cement: 3 fine sand ) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shutteringand reinforcement with M20 (1 cement : 1 .5 coarse sand :3 stone aggregate 20 mm nominal size) |
| 40 | Centring and shuttering including strutting proping etc. and removal of form work for: ( a) Foundation, footings, bases of columns etc. and mass concrete |
| 41 | b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 42 | d) Lintels, beams, girders, bressumers and cantilevers etc. |
| 43 | e) Column, pillars, posts and struts etc. |
| 44 | c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height) |
| 45 | Reinforcement of RCC work including bending, binding and placing in position complete. |
| 46 | Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand) |
| 47 | Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3 coarse sand) in foundation and plinth. |
| 48 | Extra for half brick masonry in superstructure above plinth level and up to floor two level. |
| 49 | Providing approved best available local wood (Class-BII) work in frames of doors, windows clerestory windows and other frames,wrought framedand fixed in position |
| 50 | Providingand fixing panelled,glazed or panelled and glazed shuttersfor doors, windows and clerestory windows including aluminium butt hinges with necessary screws |
| 51 | Providing and fixing 40x3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts,nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1:3:6 (1 cement : 3 sand : 6hard stone chips 40 mm nominal size) |
| 52 | Providing and fixingMSgrillsof required pattern in wooden frames of window setc with MS flat, square or round bars with round headed bolts and nuts or by screws. (b) Ornamental grill. |
| 53 | Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete. (a) 300 x 16 mm |
| 54 | Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete (a) 300 x 10 mm |
| 55 | c) 150 x 10 mm |
| 56 | Providing and fixing aluminum Handlesanoised transparent or dyed to required color or shade with necessary screws etc complete (a) 125 mm |
| 57 | b) 100 mm |
| 58 | Providing and fixing MS Hooks and Eyes.(b) 150 mm |
| 59 | Cement concrete flooring 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. (c) 75 mm thick |
| 60 | Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3 coarse sand) finishedwith a floating coat of neat cement, including rounding of junctions with floor. (b) 21 mm thick |
| 61 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete(a) Size of Tile 500 x 500 mm |
| 62 | Providing and fixing on wall face C.I. rain water pipe including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 (1 cement : 2 fine sand) (b) 100 mm diameter pipe |
| 63 | Providing and fixing M.S.Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1:2:4 mix (1cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) including cost of cutting hole sand making good the wall etc (b) 100 mm diameter |
| 64 | Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked inneat cement slurryand cement mortar 1 : 2 ( 1 cement: 2 fine sand). (b) 100 mm diameter |
| 65 | 12 mm cement plaster 1 : 3 (1 cement : 3 fine sand). |
| 66 | 15 mm cement plaster 1 : 3 (1 cement : 3 fine sand) |
| 67 | White washing with whiting on new work (three or more coats) to give even shade. |
| 68 | Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work including priming coat of whiting to give an even shade. |
| 69 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete. |
| 70 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade |
| 71 | Applying priming coat with ready mixed primer of approved brand and manufacture on steel work |
| 72 | Painting two ormore coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade. |
| 73 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth. |
| 74 | Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1:3:6 (1cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on side sand bottom and plastering on all exposed surface swith 12 mm thick cement mortar 1 : 3 (1cement : 3 fine sand) including shuttering complete. |
| 75 | Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work). (a) 15 mm nominal bore |
| 76 | b) 20 mm nominal bore |
| 77 | Providing and fixing brass bib cock of approved quality. |
| 78 | Providing and fixing brass stop cock of approved quality. |
| 79 | Providing and fixing PVC connection pipe with brass union. |
| 80 | Providing and fixing white vitreous china water closet squating pan (Indian type WC pan)size 580mmwith100mmandsandcast ironP orS trap,12.5LitrehighlevelCI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fitting sand clamps 20 mm GIover flowpipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required |
| 81 | Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete. |
| 82 | Providing and fixing white vitreous china wash basin with RS or CI brackets painted white15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass tra pand MI unions complete,including cutting and making good the walls where required |
| 83 | a)Flatback wash basinsize 550x400mmwithapairof15 mmCP brass pillartapsof heavy quality |
| 84 | Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleats with CP brass screws and washers. |
| 85 | Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleats with CP brass screws. |
| 86 | Providing and fixing CPbrasstowel rail completewith CPbrass bracketsfixed to wooden cleadt with CP brass screws (heavy quality). |
| 87 | Providing and fixing toilet paper holder. a) CP Brass |
| 88 | Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes (a) 100 mm dia |
| 89 | Providing and fixing sand cast iron heel rest sanitary bend. (a) 100 mm dia |
| 90 | Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. (a) 100 x 100 x 100 mm |
| 91 | Internal Electrification |
