Tender For Repair And Maintenance Of Various Houses, Hutments Damaged/Cracked At Dudha Tola Village And Repair Of Dudhatola School Due To Aocm Mine Blasting Under A-Docm Sub Area
Tender Value
4.92 Lakhs
Estimated cost
Bid Submission
27 Sep 2025
0 days left
EMD
6200
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
sohagpur → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repair And Maintenance Of Various Houses, Hutments Damaged/Cracked At Dudha Tola Village And Repair Of Dudhatola School Due To Aocm Mine Blasting Under A-Docm Sub Area
BOQ
| Sl. No. | Item Description |
| 1 | Item Description/ Heading |
| 2 | 12 mm cement plaster:1:6 (1 cement : 6 fine sand) |
| 3 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.25 mm thick with 20 mm nominal size stone aggregate |
| 4 | Brick work withfly ash bricks of class designation50 conforming to IS: 2222 -1991 in superstructure above plinth level upto floor five level in cement mortar 1:6(1 cement : 6 coarse sand): With fly ash bricks. |
| 5 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 6 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 7 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 8 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 9 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :300x16 mm. |
| 10 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :200x10 mm. |
| 11 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :100x10 mm . |
| 12 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm |
| 13 | White washing with lime to give an even shade : Old work (one or more coats) |
| 14 | Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : Old work (one or more coats) |
| 15 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.99.1 One or more coats on old work |
| 16 | Providing and fixing to existing door frames.30 mm thick factory made Polyvinyl Chloride (PVC) doorshutter made of styles and rails of a uPVC hollow section ofsize 60x30 mm and wall thickness 2 mm (± 0.2 mm), withinbuilt decorative moulding edging on one side. The stylesand rails mitred and joint at the corners by means of M.S.galvanised/ plastic brackets of size 75x220 mm having wallthickness 1.0 mm and stainless steel screws. The styles ofthe shutter reinforced by inserting galvanised M.S. tube ofsize 25x20 mm and 1 mm (± 0.1 mm) wall thickness. Thelock rail made up of \"H\" section, a uPVC hollow section of size100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to theshutter styles by means of plastic/ galvanised M.S. \"U\" cleats. |
| 17 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 18 | White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap. |
| 19 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White |
| 20 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia. |
| 21 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 15 mm nominal outer dia Pipes. |
| 22 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 23 | Providing and fixing PTMT bib cock of approved quality and colour. (18.54.1) 15mm nominal bore, 86 mm long, weighing not less than 88 gms |
| 24 | Providing and fixing PTMT stop cock of approved quality and colour. 15 mm nominal bore, 86 mm long, weighing not less than 88 gms. |
| 25 | Clearing grass and removal of rubbish uptp a distace of 50 m out side the periphery of the area cleared. |
| 26 | carriage of debris by By Mechanical Transport including loading,unloading and stacking upto a lead of 1 km |
| 27 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm includingpointing the joints with white cement and matching pigment etc.,complete. |
| 28 | Providing and fixing G.I. pipes complete with G.I. fittings includingtrenching and refilling etc. 40 mm dia nominal bore |
| 29 | Total impact of GST for the purpose of CTC |
AI Tender Summary
Tender Timeline
Sep 16, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedSep 27, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedSep 29, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender