Tender For Provision Of Fire Detection/ Alarm/ Fighting System At Esic, Haryana. - Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. 2 All kinds of soil 3 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 4 25 mm nominal bore 5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 6 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 7 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 8 Cement mortar 1:4 (1 cement : 4 coarse sand) 9 Providing and laying up to floor five level reinforced cement concrete in kerbs, steps and the like excluding the cost of centering,shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 10 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 11 Thermo-Mechanically Treated bars of grade Fe-500D or more. 12 Centering and shuttering with 12mm thick shuttering plywood conforming to IS 4990:2011 and removal of form at all heights. Plywood will be supported on lock bars. 13 Suspended floors, roofs, landings, balconies and access platform. 14 Centering and shuttering including strutting, propping etc. and removal of form work for : 15 Foundations, footings, bases for columns 16 CEMENT PLASTER (IN COARSE SAND) 17 12 mm cement plaster of mix : 18 1:4 (1 cement: 4 coarse sand) 19 Providing and applying plaster of paris putty of 2 mm thickness overplastered surface to prepare the surface even and smooth complete. 20 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 21 New work (two or more coats) over and including water thinnable priming coat with cement primer 22 Finishing walls with Acrylic Smooth exterior paint of required shade : 23 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 24 Neat cement punning. 25 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 26 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 27 Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc.complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately). 28 Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm. 29 Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete. 30 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately). 31 12mm thick commercial ply conforming to IS : 1328 BWR type 32 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. 33 Using M.S. angels 40x40x6 mm for diagonal braces 34 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 35 Two or more coats on new work 36 Providing, laying, testing & commissioning of C class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 37 80 mm dia 38 100 mm dia 39 150 mm dia 40 250 mm dia (wall thickness 6.3 mm) 41 Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : 42 Single headed Gunmetal 43 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 44 30 m 45 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : 46 Gun Metal 47 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : 48 Gun metal 49 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 50 80mm dia 51 150mm dia 52 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 53 80mm dia 54 100mm dia 55 150mm dia 56 Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-F insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. 57 2280 lpm at 70 m Head 58 Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-F insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 59 180 lpm at 70 m Head 60 Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 61 2280 lpm at 70 m Head 62 Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required : 63 Incomings400A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital Voltmeter 0-500V with selector switch Ammeter (0-400 A) with selector swtich & CTs etc. LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Set of Copper Bus Bar 500AOutgoings( Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps)Main Fire Pump200 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 75 hp pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation.Jockey Pump100 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. Diesel Engine ControlControl for diesel engine comprising - Automatic/Manual selctor switch & 3 attempt starting device, timers and relays as required, push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0- 20 A DC Ammeter All standard relays and accessories for automatic operation of diesel engine System Controller Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specifications. 64 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. 65 Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 66 2 way-100 mm dia M.S. Pipe 67 4 way - 150 mm dia M.S. Pipe 68 Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. 69 Providingand fixing one coatof 4 mm thick MAKPOLY KOTE anti rust pipe protection including primer and lap of 25mm onexternal M.S. pipe complete including surface preparation complete in 70 Supply & Installation of vibration pads Set of 4 Piece for Main Fire Pump, Jokey Pump & Deisle Pump in Pump Room (1 Set Per Unit) 71 Supplying and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 72 70 sq. mm 73 HAVEELS Copper Cable 2 Core 1.5 Sqmm 74 HAVEELS Copper Cable 3 core x 4 Sqmm(For Jockey pump) 75 Extinguishers FK CO2 Type 4.5kg squeeze Grip/ Wheel MS Body FE ( Make:-FLAMEKLOG ) 76 Extinguishers FK Foam Type 9L MS Body FE ( Make:-FLAMEKLOG ) 77 Extinguishers FK ABC Powder Type Map-90 4kg FE ( Make:-FLAMEKLOG ) 78 FOOT VALVE Cast Iron Foot Valve Flanged End 80mm ( Make:- KIRLOSKAR ) 79 FOOT VALVE Cast Iron Foot Valve Flanged End 100mm ( Make:- KIRLOSKAR ) 80 FOOT VALVE Cast Iron Foot Valve Flanged End 150mm ( Make:- KIRLOSKAR ) 81 Pressure gauge 50 mm ( Make:- SNSM,Model Code 50B2007D ) 82 Fire Hose cabinet Double Door ( Make:- Kalpex ) 83 Hydrolic Door Closer ( 80 Kg ) ( Make:- Ozone, Model:- NSK-980E STD LIGHT-GREY ) 84 Fire Scheme Drawmatry on the Scheduled Building Plan 85 Fire evcuation plan/map (NIGHT GLOW) 12X18 86 Fire evcuation plan/map (NIGHT GLOW) 8X12 A4 87 STAIR EXIT (NIGHT GLOW) 4X10 88 Lift 4X8 89 Ladies Toilet 8X8 90 Gents Toilet 8X8 91 Danger 6X6 92 FIRE EXTINGUISHER (NIGHT GLOW) 6X6 93 MCP (FIRE ALARM) (NIGHT GLOW) 6X6 94 FHC (FIRE HOSE CABINET) (NIGHT GLOW) 4X8 95 RESTRICTED AREA 6X12 96 DO NOT SPIT. 8X12 97 NO SMOKING 8X12 98 IN CASE OF FIRE DO NOT USE LIFT (NIGHT GLOW) 8X8 99 PUSH 2X6 100 PULL 2X6 101 Fire Exit sine board 6x12
