|
| 1 | Charpoy GI PIPE Plywood top(FD-220) |
| 2 | Removing of unserviceable plytop from charpoy and supply and fix new6\"x3\"x12mmthick plywood top BWR grade fixed with inculding nuts , washers and bolts to frame work, complete all as specified and as directed by Engineer-in-charge. |
| 3 | Removing of old unserviceable/broken Elbow and Supply & fix new 03 way GI Elbow 70mm long of 32mm dia ISI marked and fixing in position, complete all as shown on drawing (Wt. not less than 420gm per elbow) |
| 4 | Removing of old unserviceable/broken check nut and S&F new 06mm thick ISI marked GI check nut of 32mm dia, complete all as shown on drawing. |
| 5 | Welding to broken joints of charpoy GI pipe, complete all as directed by Engr-in-Charge. |
| 6 | Removing of old unserviceable long rail from existing charpoy GI pipe and Supply & fix new long rail of 32mm dia medium grade GI pipe, ISI marked and threading the same 22mm long at one end 52mm long at other end anf fixing in position, complete all as showm on drawing. |
| 7 | Cutting and converting the old unserviceable long rail as retrieve vide Srl No. 1.05 here-in-before into two short rails and fixed to charpoy GI pipe duly threaded 22mm long at both side end including removal of old and broken threaded short rails, complete all as directed by Engr-in-Charge. |
| 8 | Cutting and converting the old unserviceable short rails as retrived vide Srl ite No. 1.06 here-in-before into two legs and fixed to charpoy GI pipe duly threaded 22mm long at one end including removal of old and broken unserviceable legs, complete all as directed by Engr-in-Charge. Note : Before placing the work order in respect of Srl item No. 1.05 & 1.06 of sch \"A\" Part-I(BOQ) the necessary cutting schedule be prepared and get approved from the accepting Officer. |
| 9 | Table office clerk steel (FD-1004) |
| 10 | Removing of old unserviceable top from table office clerk steel and supply and fixing the new top of same size made out of 18/19mm thick pre-laminated particle board teak faced wth 4mm thick teak wood beading all around the table top all as shown on drg, complete all as directed by Engr-in-Charge. |
| 11 | Table Bed Side officers(FD/E6/MAP/15 (R)) |
| 12 | Replacement of upper drawer made of 18mm thick teak faced prelaminated particle board, exterior grade and provided with 6mm thick bottom of ISI marked commercial plywood of BWR grade, complete all as directed by Engr-in-Charge. |
| 13 | Replacement of lower drawer made of 18mm thick teak faced prelaminated particle board provided with 6mm thick bottom of ISI marked commercial plywood of BWR grade & telescopic channel of best quality as approved, complete all as directed by Engr-in-Charge. |
| 14 | Removing of old unserviceable top from table bed side and supply & fixing the new top of same size made out of 18/19mm thick exterior grade pre-laminated particle board teak faced with 4mm thick teak wood beading all as shown on drg, complete all as directed by Engr-in-Charge. |
| 15 | All as per srl item No. 3.03 here-in-before but side of table bed side, complete all as directed by Engr-in-Charge. |
| 16 | Removing of old unserviceable back ply of table bed side and supply & fixing the new back ply of same size made out of 6mm thick commercial plywood all as shown on drg, complete all as directed by Engr-in-Charge. |
| 17 | Removing of old unserviceable handle from the table bed side and supply and fixing new CP steel handle 100mm long as per sample, shape and size all as per drg, complete all as directed by Engr-in-Charge. |
| 18 | Table Centre(FD-274) |
| 19 | Removing of old unserviceable top from table centre and S&F new top made out 18/19mm thick exterior grade pre-laminated praticle board teak faced with 4mm thick wood beading all-around the top of teapoy wooden, complete all as directed by Engr-in-Charge. |
| 20 | Replacement of old unserviceable leg from existing table centre and S&F the same size new leg made out ISI 1st Class hard wood teak to table centre duly french polished all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 21 | All as per srl item No. 4.02 here-in-before but long rail, complete all as directed by Engr-in-Charge. |
| 22 | All as per srl item No. 4.02 here-in-before but short rail, complete all as directed by Engr-in-Charge. |
| 23 | All as per srl item No. 4.02 here-in-before but stiffner of table centre, complete all as directed by Engr-in-Charge. |
| 24 | Teapoy Wooden (FD-278) |
| 25 | Removing of old unserviceable top from teapoy and S&F new top made out 18/19mm thick exterior grade pre-laminated praticle board,teak faced, ISI marked with 04mm thick reak wood beading all-around the top of table centre, complete all as directed by Engr-in-Charge. |
| 26 | Replacement of old unserviceable leg from existing teapoy wooden and supply and fixing the same size new leg made out ISI 1st Class hard wood teak to teapoy wooden duly french polished all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 27 | All as per srl item No. 5.02here-in-before but long rail, complete all as directed by Engr-in-Charge. |
| 28 | All as per srl item No. 5.02 here-in-before but short rail. complete all as directed by Engr-in-Charge. |
| 29 | All as per srl item No.5.02 here-in-before but stiffner of teapoy wooden, complete all as directed by Engr-in-Charge. |
| 30 | Table peg (FD-277) |
| 31 | Removing of old uunserviceable top from peg table and S&F new top made out of 18/19mm thiick exterior grade pre-laminated praticle board,teak faced, ISI marked with 4mm thick teak wood beading all around the top of peg table, complete all as directed by Engr-in-Charge. |
| 32 | Replacementof old unserviceable leg from existing peg rable and S&F the same size new leg made out 1st class kard wood teak to peg table duly french polished all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 33 | All as per srl item No. 6.02 here-in-before but long rail, complete all as directed by Engr-in-Charge. |
| 34 | All as per srl item No. 6.02 here-in-before but short rail, complete all as directed by Engr-in-Charge. |
| 35 | All as per srl item No. 6.02 here-in-before but stiffner of peg table, complete all as directed by Engr-in-Charge. |
| 36 | Table writing(FD-275) |
| 37 | Removing of old unserviceable top from table writing and S&F new top made out 18/19mm thick exterior grade pre-laminated praticle board teak faced with 4mm thick wood beading all-around the top of table writing, complete all as directed by Engineer-in-Charge. |
| 38 | Removal of old damaged door complete from table writingand S&F the new door of same size with piano type hinges made out 18/19mm thick exterior pre-laminated particle board top all as shown in drawing including one coat of french polishand including aluminium anodised knob, complete all as directed by Engineer-in-Charge . |
| 39 | Replacement of unserviceable drawer with new drawer of same size and shape to table writing,front of the drawer shallbe made out 18mm thick, exterior grade pre-laminated particle board teak faced and including aluminium anodized knob. Side,base and back of drawer made out of 12 mm tfick ply wood(ISI marked) and fixing all as shown in drawing including one coat of french polish, complete all as directed by Engr-in-Charge. |
| 40 | Replacement of unserviceable leg of table writing with new leg made out of 1st class hard wood teak all as shown on drawing includingone coat of french polish, complete all as directed by Engr-in-Charge. |
| 41 | Removal of old unserviceable back ply of table writing and S&F the new back ply of same size of 12mm thick OSTF commercialplywood, ISI marked (Irrespective of all as shown on drawing ) including one coat of french polish, complete all as directed by Engr-in-Charge. |
| 42 | All as per srl item No. 7.05 here-in-before but side ply, complete all as directed by Engr-in-Charge. |
| 43 | Removing old broken/unserviceable side short rail of table writing and S&F new side short rail made of 1st class hard wood teak as per shape and size shown in drawing, complete all as directed by Engr-in-Charge. |
| 44 | Removing old broken/unserviceable side long rail of table writing and S&F new side long rail made of 1st class hard wood teak as per shape and size shown in drawing, complete all as directed by Engr-in-Charge. |
| 45 | Removing old broken/unserviceable knob of table writing and S&F new CP brass knob as per sampleshape and size shown in drawing, complete all as directed by Engr-in-Charge. |
| 46 | Removing old broken/unserviceable stiffiner of table writing with new long/short stiffiner madeof 1st class hard wood teak as per shape and size shown in drawing, complete all as directed by Engr-in-Charge. |
| 47 | Table dinning 6 pers(FD-273) |
| 48 | Removing of old unserviceable top from table dining 06 personsand supply and fixing new top made out of 18/19mm thick pre-laminated particle board, teak faced with 4mm thick wood beading all around the top of table dining 06 persons complete all as directed by Engineer-in-Charge . |
| 49 | Replacement of old unserviceable leg from existing table dining 06 persons and supply and fixing the same size newleg made out of 1st class hard wood teak to table dining 06 persons duly french polished all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 50 | All as per srl item No. 8.02 here-in-before but long rail, complete all as directed by Engr-in-Charge. |
| 51 | All as per srl item No. 8.02 here-in-before but short rail, complete all as directed by Engr-in-Charge. |
| 52 | All as per srl item No. 8.02 here-in-before but stiffner of size 100x25mm under the top joining the top long side of top rails of table dining 06 persons, complete all as directed by Engr-in-Charge. |
| 53 | S&F new right angle of size 15x30x5mm thick with steel screws to legs, complete all as directed by Engr-in-Charge. |
| 54 | S&F wooden corners made of first class hard wood teak to legs joining top rails each with 04 Nos of steel screws, complete all as directed by Engr-in-Charge. |
| 55 | Table Dressing Ladies with Mirror(FD-251) |
| 56 | Removing of old unserviceable looking mirror from table dressing ladies and supplying and fixing new looking mirror of size 1200 x 450 x 05 mm Thick of modi-gaurd duly fixed in and including frame of teak wood and polishing complete in all respect to fix on wall as shown on drawing, complete all as directed by Engr-in-Charge. |
| 57 | Removing of old broken/unserviceable knob from table dressing ladies and S&F new 40 mm size CP Brass knob as per shape and size shown in drawing, complete all as directed by Engr-in-Charge. |
| 58 | Removing of old broken/unserviceable sliding glass from table dressing ladies and S&F new 5mm thick sheet glass with plastic handle as per sample, shape and size shown in drawing, complete all as directed by Engr-in-Charge. |
| 59 | Removing old broken/unserviceable legs from table dressing ladies and S&F new legs of 1st class hard wood teak as per shape and size shown in drawing including french polishing to match the other parts, complete all as directed by Engr-in-Charge. |
| 60 | Removing old broken/unserviceable sunmica from the top of table dressing ladies and S&F new 1.5 mm thick sunmica of best quailty fixed with fevicoal as per shape and size shown in drawing, complete all as directed by Engr-in-Charge. |
| 61 | Chair writing (MAP) FD/E6/MAP/12 |
| 62 | Replacement of old unserviceable seat and back of chair with new seat of 12mm thick plywood commercial quality (ISI marked) coverd with 75mm thick U foam and best quality of tapestry cloth. The backshall be 6mm thick plywood commercial quality (ISI marked) fixed to frame with screw and covered with 40mm thick U foam over shape and best quality of tapestry cloth. Seat and back fixed on frame with screw and including all minor repairs with welding to steel frame etc, complete all as specified and as directed by Engineer-in-Charge. |
| 63 | Welding to broken joints of chair writing, complete all as directed by Engr-in-Charge. |
| 64 | Replacement of old unserviceable broken arm rest with new arm of black integral skin polyurethane reinforced with MS insert and all shall be scratch and weather resistant of chair briefing static base, complete all as directed by Engr-in-Charge. |
| 65 | Chair Dinning (MAP) FD/E6/MAP/10 (R) |
| 66 | Removing old broken unserviceable front legs from chair dining and S&F new fronts legs of 1st class hard wood reak wood as per shape and size shown in drg, complete all as directed by Engr-in-Charge. |
| 67 | All as per srl No.11.01 here-in-before but rear legs, complete all as directed by Engr-in-Charge. |
| 68 | All as per srl No. 11.01 here-in-before but front/back/side rail, complete all as directed by Engr-in-Charge. |
| 69 | All as per srl No.11.01 here-in-before butback teak wood strip of size 30x15mm of suitable length, complete all as directed by Engr-in-Charge. |
| 70 | All as per srl No.11.01 here-in-before but stiffner, complete all as directed by Engr-in-Charge. |
| 71 | Removing old unserviceable foam cushioned seat from existing chair dining cushioned and S&F new 75mm thick, 0 density foam seat of (Make : Sleepwell/Feather foam/ Kurl-on) to chair dining duly covred with leatherite covercolour, shade and quality of leatherite shall be as approved by the AGE(I), complete all as directed by Engr-in-Charge. |
| 72 | S&F new wooden brcket/corners of suitable size made 1st class hard wood teak to chair dining cushioned and screwd with railing for extrea strength including french polish, complete all as directed by Engr-in-Charge. |
| 73 | Chair verandah (FD-256, 359) |
| 74 | Conduit section any member of MS conduit pipe 16G, 19mm dia as per drg, complete all as directed by Engr-in-Charge. |
| 75 | Welding joints of leg of 19/20mm MS tube and other joints as per drg, complete all as directed by Engr-in-Charge. |
| 76 | Removing of old paint complete by scrapping, preparing surface smooth and painting to the entire frame inculding removign old unserviceable cane from chair verandah and recanning the chairs etc with approved new plastic cane 4mm wide half round as per mattpattern all as specified color of cane shall approved by AGE(I), complete all as directed by Engr-in-Charge. |
| 77 | Chair EasyFD-229/201/17 |
| 78 | Removing old broken unserviceable rear legs from chair easy and S&F new rear legs of 1st class hard wood reak wood as per shape and size shown in drg, complete all as directed by Engr-in-Charge. as per drg |
| 79 | All as per srl No.13.01 here-in-before but front legs as per drg, complete all as directed by Engr-in-Charge. |
| 80 | All as per srl No.13.01 here-in-before but seating/back frame memebers front back side rail as per drg, complete all as directed by Engr-in-Charge. |
| 81 | All as per srl No.13.01 here-in-before but arm rest as per drg, complete all as directed by Engr-in-Charge. |
| 82 | M&L for Re-canning of chair easy (Seat) in Godrej pattern with oval shape 2mm wide new white plastic cane and 3mm wide at the edge make as approved by AGE(I) inculding taking out old canning complete all as shown on drawing inculding PVC shoe to each legs, complete all as directed by Engr-in-Charge. |
| 83 | M&L for Re-canning of chair easy (Back) in Godrej pattern with oval shape 2mm wide new white plasitc cane and 3mm wide at the edge make as approved by AGE(I) inculding taking out oldcanning complete all as shown on drawing inculding pvc shoe toe each legs, complete all as directed by Engr-in-Charge. |
| 84 | Sofa Set 04 seater & 05 Seater with cushion FD-281 |
| 85 | Removing of old unserviceable arm rest from existing sofa set 04 seater & 05 seater and S&F new 1st class hard wood teak arm rest to sofa set 05 seater &04 seater all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 86 | All as peritem No. 14.01 here-in-before but front rail of sofa set single piece of 01 seat, complete all as directed by Engr-in-Charge. |
| 87 | All as per item No 14.01 here-in-before but side rail of sofa set, complete all as directed by Engr-in-Charge. |
| 88 | All as per item No 14.01 here-in-before but legs of sofa set, complete all as directed by Engr-in-Charge. |
| 89 | All as per item No 14.01 here-in-before but wooden battens of sofa set, complete all as directed by Engr-in-Charge. |
| 90 | S&F of foam cushion of size 22\" x 21\" ,100 mm thick 32 density duly covered with best tapestry cloth of approved quality and colour, complete all as directed by Engr-in-Charge. |
| 91 | Removal of tapestry cloth from existing seat/back of Sofa set 04 & 05 seater and S&F new tapesty cloth from existing seat/back of sofa set 04 seater & 05 seater and providing new tapestry cloth DCM/Handloom long cloth of approved shade of Indian make and fixing the same all as per drawing, complete all as directed by Engr-in-Charge. |
| 92 | Almirah large steel & Almirah medium steel(FD-1031) |
| 93 | Removing of old unserviceable handles from Almirah large steel & Almirah Medium steel and S&F new CP steel handle of exisiting size to almirah large steel as shown on drawing, complete all as directed by Engr-in-Charge. |
| 94 | Removing of old unserviceable lock from Almirah large steel & Almirah Medium steel S&F new brass lock 75mm long, 06 lever with two keys to Almirahsteel all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 95 | Removing of old unserviceablehandle & lock assembly from Almirah large steel & Almirah Medium steel and S&F new handle & lock assembly to Almirahsteel including making adjustment ofdoor shutter & applying one coat of synthetic enamel paint over a coat of primer after preparation of surfaces complete with spray machine all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 96 | Removing of old unserviceable foot rest from Almirah large steel & Almirah Medium steel and S&F new foot rest made out of 01mm thick MS black sheet (PBI) of existing size, shape and welding at appropriate points and applying one coat of synthetic enamel paintover a coat of primer after preparation of surfaces complete with spray machine, complete all as directed by Engr-in-Charge. |
| 97 | All as per Sr.item No. 15.01 here-in -before but bottom sheet ofalmirah steel, complete all as directed by Engr-in-Charge. |
| 98 | All as per Sr.item No. 15.01 here-in -before but shelf of almirah large steel, complete all as directed by Engr-in-Charge. |
| 99 | Removing of old unserviceable butt hinges of Almirah steel and S&F new butt hinges 75mm long and adjusting door by revitting / welding complete all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 100 | M&L for removing the dented/loose shlef from Almirah steel and refixing it with mild steel revitting /spot welding after bringing it to original shape, complete all as directed by Engr-in-Charge. |
| 101 | Locker Bed side Steel(FD-257) |
| 102 | Replacement of old unserviceable hasp and staple with new 100mm long MS chromium plated hasp and staple all as shown drg, complete all as directed by Engr-in-Charge. |
| 103 | Replacement of old unserviceable bow handle with new 100mm long CP steel bow handle all as shown drg, complete all as directed by Engr-in-Charge. |
| 104 | Replacement of unserviceable conduit pipe with new CP steel conduit pipe of siutable size of 20mm dia having wall thickness 1.25mm to locker steel, complete all as directed by Engr-in-Charge. |
| 105 | Replacement of unserviceable socket with new aluminium socket/brackets suitable for MS 20mm dia conduit pipes, complete all as directed by Engr-in-Charge. |
| 106 | Removing of old unserviceable foot rest from locker bed side steel andsupply and fixing new foot rest made out of 1mm thick MS black sheet (PBI) of existing size, shape and welding at appropriate points and applying one coat of synthetic enamel olive green paint with spray machine over a coat of primer after preparation of surfaces, complete all as directed by Engr-in-Charge. |
| 107 | All as per Sr.item No. 16.05 here-in -before but bottom sheet oflocker bed side steel, complete all as directed by Engr-in-Charge. |
| 108 | Removing of old unserviceable MS hinges of locker bed steel and S&F new MS hinges 65mm long with gas welding / revitting complete all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 109 | M&L for refixing of loose shelves with mild steel revitting / spot welding, complete all as directed by Engr-in-Charge. |
| 110 | Table 3x2 with drawer / Without drawer FD-283& 284 |
| 111 | Removing of old unserviceable top from Table 3\"x2\" wooden with / without drawer and S&F the new top of same size made out of18/19mm thick exterior grade pre-laminated particle board teak faced having 4mm thick teak wood beading all-around the table top all as shown on drawing, complete all as directed by Engr-in-Charge. |
| 112 | Charpoy with ply top , Bed Hard FD / MAP-II / 01 |
| 113 | Removing of old unserviceable plytop from Charpoy with hard top and S&F of 12mm thick plywood of suitable size , ISi marked, BWR bonded commercial plywood with unpolished edging of approved quality all as shown on drg, complete all as directed by Engr-in-Charge. |
| 114 | Removing of unserviceable long rail (length approx 1.98m) MS tube side 25x65mmx16 guage from charpoy with hard top and supply and fix new MS tube side 25x65mmx16 guage as per as exitsting specification duly painted two coats of synthetic enamel paints black colour over red oxide paint , all as shown on drg, complete all as directed by Engr-in-Charge. |
| 115 | Removing of unserviceable short rail (length approx 0.90m) MS tube side 25x65mmx16 guage from charpoy with hard top and supply and fix new MS tube side 25x65mmx16 guage as per as exitsting specification duly painted two coats of synthetic enamel paints black colour over red oxide paint , all as shown on drg, complete all as directed by Engr-in-Charge. |
| 116 | Supply and fixing in replacement of MS tube legs (appx length 440mm) 32x32mmx16 guage, two coat of synthetic enamel paint black colour over red oxide paint, all as shown on drawings, complete all as directed by Engr-in-Charge. |
| 117 | Supply and fixing in replacement of MS plate 32x32x5mm welded at bottom of legs and under which 3mm thick rubber sheet fixed with adhesiv all shown on drawing, complete all as directed by Engr-in-Charge. |
| 118 | Supply and fixing in replacement of stiffeners 25x25xmm x 16guage (appx length 0x90m)MS tube two coat of synthetic enamel paint black colour over red oxide paint all as shown on drawings, complete all as directed by Engr-in-Charge. |
| 119 | Bed Hard (MAP) FD/E6/MAP/08 (R) |
| 120 | Removing of old unserviceable plywood12mm thick BWR grade (Make : Century ply/Archid Ply) as exising shape and sie with 8 Nos Shunken/Bolt appropriate whole shall be make with electric drill machine complete rest all as drg and directed. |
| 121 | Removing unserviceable head board form bed hard steel and fix new 18mm thick prelaminated particle board with PVC edging all as shown on drg and complete all as specified and as directed by Engnieer-in -charge. |
| 122 | Removing unserviceable foot board form bed hard steel and fix new 18mm thick prelaminated particle board with PVC edging all as shown on drg and complete all as specified and as directed by Engnieer-in -charge. |
| 123 | Removing unserviceable long rail (length approx 1.974m) MS tube side 25x65mmx18 guage rect CR pipe form bed hard steel and supply and fix new MS tube side 25x65mmx18 guage as per as exitsting specification duly painted two coats of synthetic enamel paints black colour over red oxide paint , all as shown on drg and complete all as specified and as directed by Engineer-in-charge |
| 124 | POLISH :- Material and labour for complete removing/scrubbing of entire old polished surfaces of the following items with appropriate sand paper / emary paper etc, including preparation of old wooden surfaces by applying seina/burnt seina uniformally for french polish in order to obtain the required glossy finish and applying two coats of french polish to the following wooden furniture items to the entire satisfaction of Engr-in-Charge and all as directed. |
| 125 | ChairDining FD - 279 |
| 126 | ChairWriting FD - 280,250 |
| 127 | Table pegFD- 277,384 |
| 128 | Teapoy Wooden FD– 278 |
| 129 | Table Centre FD-235,274 |
| 130 | Table Dressing Ladies with Mirror FD-251 |
| 131 | Table Dining 06 Person FD- 239, 273 |
| 132 | Sofa Set 05 seater with cushion FD-281, FD/MAP-II/02 |
| 133 | Sofa Set 04 seater with cushion FD-281, FD/MAP-II/02 |
| 134 | Table 3x2 with/ without drawer FD- 283 |
| 135 | Table writing FD-249, 275 |
| 136 | PAINTING :-M&L for one coat of painting by means of spray painting with synthetic enamelled paint of appropriate shade and quality to steel furniture items (internally & externally complete) including removing of dents & filling with putty after preparation of surfaces thoroughly by using appropriate abrasive cloth emery as required as trade practice complete all as specified and as directed by Engineer-in-Charge to the following steel furniture items :- |
| 137 | Almirah large steel with shleves FD-1031 |
| 138 | Almirah medium/small steel FD-1032 |
| 139 | Bed Hard (MAP) FD/E6/MAP/08 ( R ) |
| 140 | Charpoy IP hard top FD/MAP-II/01 |
| 141 | Charpoy GI PIPE Plywood top(FD-220) Silver Colour |
| 142 | Locker bed side steel FD-257,1029 |
| 143 | Table Office Clerk steel FD- 1004 |
