Tender For Construction Of Hard Standing In Mt Garage Asc Bn (Mt) At Mil Stn Haldawani; 1 Surface dressing in soft / loose soil n. exc. 15 cm deep complete all as specified and as directed. 2 Surface Excavation in hard/dense soil n.exc. 30cm deep and averaging 15cm deep and getting out complete all as specified and directed. 3 Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in Hard/ Dense soil complete all as specified and directed. 4 M&L for Earth work in excavation for all kinds of soil by mechanical means(Hydraulic excavator) means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in charge 5 Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil complete all as specified and as directed. 6 Spreading & levelling in layers n exc. 25 cm thick & well ramming including watering as required complete all as specified and as directed. 7 Removing Excavated soil exceeding 250 M but not exceeding 1.50KM and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed. 8 M & L for hard core of gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed. 9 M&L for bringing soil from outside MOD land and spreading, levelling ramming under floors, foundations including watering and consolidation as directed by engineer in charge. 10 M&L for ATT Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed. 11 M&L for ATT Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed. 12 M&L for ATT Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed. 13 M & L for Cement concrete in foundations, filling and mass concrete Type D2PCC 1:4:8(40 mmgradedaggregate) complete all as specified and as directed. 14 M & L for Cement concrete in foundations, filling and mass concrete Type C2 PCC 1:3:6(40 mmgradedaggregate) complete all as specified and as directed. 15 Surface channel in concrete 1:3:6 (40 mm graded aggregate) for drain complete all as specified and directed. 16 M&L for RCC pre-cast type B-1 (1:2:4) (using 20mm graded crushed stone aggregate) as in cover slabs for manholes etc set in cement mortar (1:4) complete all as specified and directed by Engr-in-charge.NOTE: Reinforcement for cover slabs will be provided under respective item separately. 17 M & L for Reinforced cement concrete (design mix) in, Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete M-25 (20mm graded aggregates) complete all as specified and as directed. 18 M & L for Reinforced cement concrete (design mix) M-25(20mm graded aggregates) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. 19 M & L for Reinforced cement concrete (design mix) M-25(20mm graded aggregates) in Chajjas complete all as specified and as directed. 20 M & L for Reinforced cement concrete (design mix) M-25(20mm graded aggregates) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. 21 M & L for Reinforced cement concrete (design mix) M-25(20mm graded aggregates) in Columns, pillars, piers, posts and struts complete all as specified and as directed. 22 Extra for forming fair finished drain or channel 30 cm inner girth in cement complete all as specified and directed, concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. All as specified and directed. 23 M & L for laying of fine river sand, free from sharp material for cable cushioning in trenches complete all a specified and as directed. 24 Supply only integral water proofing compound complete all as specified & directed. 25 M & L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in Cement mortar (1:4) complete all as specified and as directed. 26 M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding6m mean radius, built in cement mortar (1:6) complete al as specified and as directed. 27 M & L for Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in 1:4 cement mortar complete all as specified and as directed. 28 Damp proof course to horizontal or vertical surfaces including necessary formwork In cement concrete 1:2:4, type B-0, 25mm thick complete all as specified and as directed. 29 Cutting chases, forwater tubing or concealed , etc, and making good to facings where required and plastering in cement mortar (1:4)cutting not exceeding 10cm girth in brick walls complete all as specified and directed. 30 M & L for brick protection covers laid over cables of sub class B bricks old size complete all as specified and as directed. 31 Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed. 32 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) Flat complete all as specified and as directed. 33 Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed. 34 Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed. 35 Formwork to sides of pillars, posts, struts, piers, columns and stanchions Square,rectangular or polygonal complete all as specified and as directed. 36 S&F Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising ofPVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) complete all as specified and as directed. 37 S&F Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 35 mm thickcomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge (Note:- stainless steel butt hinges and necessary SS screws shall be paid separately complete all as specified and as directed. 38 Providing and fixing factory made uPVC white colour fixed Windows made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including necessary provision for mosquito proofing, drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners-5mm thick glazing with selected quality glass (Note: The unit rate quoted by contractor including costof glass and includes all other connected accessories Net opening will be measured for payment purpose.) (B) Area exceeding 1.00 sqm but not exceeding 2.00 sqm each complete all as specified and as directed. 39 Providing and fixing factory made uPVC white colour fixed Windows made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners,including necessaty provision for mosquito proofing, drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners-5mm thick glazing with selected quality glass (Note: The unit rate quoted by contractor including costof glass and includes all other connected accessories Net opening will be measured for payment purpose.) (B) Area not exceeding 1.00 sqm each complete all as specified and as directed. 40 Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm (+ 0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, includingnecessary provision for mosquito proofing ,drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 8mm thick toughened glazing with selected quality glass. (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) complete all as specified and as directed. 41 Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made complete all as specified and as directed. 42 S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed. 43 Supply and fix300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed. 44 S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. 45 S & F aluminium Hat pegs, solid body, 125 mm to 175 mm complete all as specified and as directed. 46 S&F 20mm Dia Aluminium alloy anodised curtain rod decorative fancy type with brackets complete all as specified & directed. 47 S&F Aluminum anodizedTubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and as directed. 48 S & FAluminium die cast body Door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed. 49 S & F in repair MS framed work such as grills, gratings, etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 190-0 or Fe-165-0 complete all as specified and as directed. 50 M & L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 22.5cm and n exc 30cm long complete all as specified and as directed. 51 M & L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. ( TMT Bars ) complete all as specified and as directed. 52 All as per item No. 51 here in before but dia of bar 6 mm to 8 mm. 53 All as per item No. 51 here in before, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. ( TMT Bars ) complete all as specified and as directed. 54 S&F forMS Plates Fe-410- W (Gde E-250) quality B (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed. 55 M & L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS:-1161- 1979 grade St.-240 complete all as specified and as directed. 56 S & FAnodised Aluminium snap grid frame work of grid size 605x 605 mm for false ceilingcomplete all as specified and directed. 57 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. 58 S&F Pre- painted galvalume aluminum zinc coating GI based Plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. 59 S & F 4 mm thick Nonasbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium frameworkwith screws complete all as specified and as directed. 60 M & LGranite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stoneover screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes including grinding and polishing complete all as specified and directed. 61 M & L for 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement over 10mm thick plaster in cement mortar (1:4) on fair face of brick or concrete surface with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed. 62 M & L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement complete all as specified and directed. 63 M&Lfor 75 mmthick cement concrete 1:4:8 type D-2 finished fair and even as in sub base Complete all as specified and directed. 64 M&L for 100 mm thick plan cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregate) as in hardstanding, path, flooring surface finished even & smooth without using extra cement complete all as specified & directed by Engr-in-charge. 65 S&F Coloured Glazed ceramic tiles in vertical surfaces350x250mm 7mm / 450x350x7mm thickset and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in cement mortar (1:4) on fair face of brick or concrete surface complete all as specified and directed. 66 S&F Coloured Non Skid ceramic tiles7 to 8mm thick (squares/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in cement mortar (1:6) complete all as specified and directed. 67 M & L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match Light Shade over screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes complete all as specified and directed. 68 M & L for Rendering (10mm + 5 mm) thick Cement plaster1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed. 69 M & L for Rendering 10mmmm thick Cement plaster1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed. 70 M&L for rendering5 mm thickness in cement mortar 1:3 in ceilings, chajjas etc. complete all as specified and directed. 71 M&L for rendering 15 mm thickfaces of brick work or stone masonry or concrete surfaces in cement mortar 1:4 and finished fair and even without using extra cement includigmixing of water proofing compound of approved make complete all as specified. 72 M&L for preparation of new surfaces and applying 2 coats of white wash on ceilings complete all as specified and directed. 73 M& L for applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed. 74 M & L for distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, all as per manufacturers specification,two or more coats on new work complete all as specified and directed. 75 M & L for finishing walls with textured exterior paint of required shade : new work (Two or more coats applied @ 3.28 ltr/10 Sqm ) over and including priming coat of exterior prime applied @ 2.20 kg /10 sqm complete all as per manufacturers specification and as directed. 76 M & L for Prepration of newly Steel surface and applying two coat synthenic enamel paint over a coat of redoxide primer, over 10 cm in width or girth ,not otherwise described complete all as specified and directed. 77 M & L for GI pipe 25mm bore, light grade with all fittings fixed to pole and laid to floor/ ground for mechanical protection of cable complete all as specified and as directed. 78 S&F GI Tubes, `medium grade with all fitting & fixed complete to walls & ceilings or laid in floors of 15mm bore complete all as specified and as directed. 79 S&F GI Tubes, `medium grade with all fitting & fixed complete to walls & ceilings or laid in floors of 20mm bore complete all as specified and as directed. 80 S&F GI Tubes, `medium grade with all fitting laid in trenches /fixed on walls & on open surfaces of 20mm bore complete all as specified and as directed. 81 M & L for cutting existing steel tubing of size 40 to 50mm for alterations or additions alongwith insertion of GI Tee of size 40 or 50mm complete all as specified and as directed. 82 S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity complete all as specified and directed. 83 S&F CP Bib taps 15 mm bore, chromium plated, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 84 S&F CP Pillar taps 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot or `Cold with long screwed shanks & fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. 85 S & F 15 mm bore Fancy type chromium plated Wall Mixer including, connecting legs and wall flanges, screwed down high pressure with or without lettered hot and cold screwed for iron pipe complete all as specified and directed. 86 S&F 15mm bore angle cock CP, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. 87 S&F Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed. 88 S&F 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed. 89 S & F PVC connections 15mm dia, 450mm long, withPTMT nuts& washers at both ends complete all as specified and directed. 90 S&FPVC (SWR) pipes 75 mm single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed 91 S&F PVC (SWR) pipes 110 mm single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed 92 S&F PVC (SWR) 75 mmbends any radius, diminishing pieces or tapers (larger bore measured) complete all as specified and directed. 93 S&F PVC (SWR) 110 mm bends any radius, diminishing pieces or tapers (larger bore measured) complete all as specified and directed. 94 M&L for PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement with CP grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4 ) complete all as specified and directed. 95 M & L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150mm bore complete all as specified and directed. 96 M & L for 150 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed as specified complete all as specified and directed. 97 S&F Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws Complete all as specified and directed. 98 S&F Chromium platedshower rose 125 mm swivel type complete all as specified & directed. 99 S&F Waste Pipe 32 mm dia for wash basin complete all as specified and directed. 100 S&F 10 ltr capacityPVC valveless,syphonic action type, flushing cistern, low level, white, with inlet ball valve , float and handle including brackets, complete all as specified and directed. 101 S&F Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed. 102 S&F Vitreous China wash basin, white, flat back, size 580x450mm with pedestal excluding taps, waste chain & plug & porcelain stopper but including brackets and pedestal complete all as specified and directed & fixed complete all as specified and directed. 103 S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup complete all as specified and directed. 104 S&F for Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern including all necessary accessories like rag bolts/ gel gasket etc. in all respect (excluding flushing cistern & flush pipe) complete all as specified and directed. 105 Supply only Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. 106 Supply, laying, jointing and commissioning of LT XLPE 1100 volts 16sqmm 4 core grade heavy duty under ground cable PVC insulated, stranded aluminium conductor served with inner sheating of PVC tape, armoured with GI steel or tape and over all PVC sheating laid in trenches, floor through pipes, in duct on pole and roads etc. complete all as specified and as directed. 107 M & L for point wiring for Modular fittings for one light point/ fan/ bell/ 5Amps socket out let (independent) point controlled by one, one way switch with 1.5 sqmm size, PVC insulated and unsheathed 1100volts grade, single core stranded (multistrand) copper conductor (FR-LSH)PVC cable drawn into & including medium grade PVC conduit (not less than 20mmouter dia) with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) including modular metal flush box for mounting modular fittings and covered with modular cover plate with frame and cup washersincluding one continuous run of PVC insulated (green colour) 1.5 Sqmm multistrandedcopper conductor cable earth wire and connected to earth dollyfor One light/One fan/one bell point controlled by one modular switch complete all as specified and directed 108 All as per item No. 107 here in before but for, one modular socket outlet 3 pin 6 ampscontrolled by one switch on sameboard. 109 All as per item No. 107 here in before but for, one modular socket outlet 3 pin 6 ampscontrolled by one switch onindependent board. 110 All as per item No 107 herein beforebut wiringwith 2.5 sqmm copper wire (FR-LSH) PVCand 2.5 sqmm earth wire formodular socket outlet 5 pin 16 amps on independent board. 111 Supply and fix modular type switch single pole, one way 6 Amp complete all as specified and directed. 112 Supply and fix socket out letmulti 5 pin, 6 Amps, modular type complete all as specified and directed. 113 Supply and fix switch modular type single pole, one way 16 Amp complete all asspecified and directed. 114 Supply and fix socket out let 2 in1,3 pin, 6 and 16 Amp, modular type complete all as specified and directed. 115 S&F ceiling rose, PVC/ Poly carbonate,isolated body three terminal complete all as specified and directed. 116 S & F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed. 117 Supply and fix High quality LED T8 indoor batten tube light 20 Watt with aluminium extrusion in D shaped have large diameter for increased convection heat transferincl one LED PC tube rod and driver,internaly pre wired of 1.5 sqmm twin twisted flexible cableall as specified & directed.NOTE: The contractor must submit 5 years warranty for LED fitiings. 118 Supply & Fixing ofMCB SP,240 volts,AC C curve, 10 KA 6 to 32 Amps complete all as specified and as directed. 119 Supply & Fixing of MCB SPN , 240 volts,AC B curve, 10 KA 40 Amps complete all as specified and as directed. 120 Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete. all as specified and directed.NOTE : The contractor must submit 5 years warranty for LED fittings 121 S&F sheet metal enclusure for DBs(double door type)single pole and neutral 4 way including blanking platge as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed . 122 S&F sheet metal enclusure for DBs(double door type)single pole and neutral 8 way including blanking platge as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed . 123 S & FLED bulk head fitting, 1x10 watt with PDC aluminium housing and milky diffuser including LED light driver holder, complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230 Volts, 50 Hz complete all as specified and directed. NOTE: The contractor must submit 5 years warranty for LED fittings 124 M&L for earthing complete with galvanised steel,earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs belowground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways and pit/chamber in PCC 1:3:6 type C1 with suitable lifting handleto cover, GI protection pipe 15mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed.Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 15mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone at no extra cost. 125 S& F LED Bulb of 9 watt complete all as specified .NOTE: The contractor must submit 5 years warranty for LED fittings 126 S & F Exhaust fan plastic body heavy duty ISI mark, 250 mm size with louvers including all connecting accessories and cutting opening on wall and making good as per existing surface complete all as specified and directed 127 S&F service connection cable, 1100 volts grade heavy duty PVC insulated aluminium conductor, 16 Sqmm 2 core size, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mmsuspensionwire, one twin core cable flat or circular, complete all as specified and directed.
