Tender For Road Safety Work & Signage Board For 04 Nos Ramp At Ch 26.400 Km On Yamuna Expressway,Yea - Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per directionof Engineer - in - charge.Based on UPPWD SOR2020/15.2.1 2 Cement concretewith 2cm gauge approved stone ballast coarse sand & cement in the proporotion of 8:4:1 including supply of all material labour tools plants etc required for proper completion of the work 3 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concretework, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge All works upto plinth level Based on uppwd sor 2020/5.33.1 4 Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete Based on UPPWD SOR2020/5.22.6 5 Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concreteBased on UPPWD SOR2020/5.9.1 6 Centering and shuttering including strutting, propping etc. and removalof form for :Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etcBased on UPPWD SOR2020/5.9.2 7 Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. as requiredIn gratings, frames, guard bar, ladder, railings, brackets, gates and similar worksBased on UPPWD SOR2020/10.25.2 8 Cost of crane upto 40 tonne capacity complete 9 Supply of labour 10 Providing and laying of hot applied thermolpastic compound 2.5mm thick including reflectorising glass beads @250 gms per sqm area thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC :35 The finished surface to be level uniform and free form streaks and holes Rates are inclusive of all taxes royalty etc all T&P/machines material and labour required for proper completion of work. 11 Providing and fixing of speed bump it is designed so dynamically and complete that it can bear maximum load on it the body of the speed bump is made of ABS material .too highly reflectores module in PMMA material are welded with ABSSpeed bump is made of ABS, bare plate through ultrasonic welding process and then mixed on to the speed bump so that dust and water cannot touch reflectors Inside area and thus it maintains its reflectivity for aLong time Six of the speed bump. Length 350mm width 263 mm working width 250 mm height 53mm& weight 1200 gms approx. It is available in yellow and black colons as per instructions of Engineer in charge 12 Retro Reflectorised Signs (Stainless steel Framo and Post with one side sings)Supply & fixing of reflective sign board (Single side) of size 1.50x1.20 m retro reflective sheeting of HIP grade type-IV, the board shall be fixed on 50mm SS 304 grade pipe and reflective sheet on 4 mm thick, ACM sheet of standard make as per MORTH specificaton. The Board shall be fixed using 2 man post 45x45x60 cm cement concrete foundation. The stainless steel joint welding of SS pipe work shall be band and grinder property including bufting so an to give uniform shining at weded joints. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International / Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012. Legends, letters, numerals and borders etc should be as per MoRTH specification No-801.3.7. Proof of the same in form of government report shall be uploaded while quoting tenderUPPWD SOR2022/22.41
