|
| 1 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm. |
| 2 | Earthwork in filling in foundation trenches with good earth in layers not exceeding 150mm in thickness including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) a) With earth obtained from excavation of foundation. |
| 3 | Filling in foundation or plinth by Silver sand in layers not exceeding 150 mm. as directed and consolidating same by through saturation with water ramming complete including the cost of supply of sand ( payment to be made on measurement of finished quantity). (B) Do - by fine sand |
| 4 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 5 | Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with powdered earth or local sand. |
| 6 | Ordinary Cement Concrete [ Mix 3 : 1.5 : 1 ] Cement concrete with graded stone chips (20 mm.size) excluding shuttering and reinforcement, if any, in ground floor. |
| 7 | At 1st. Floor |
| 8 | Hire and labour charges for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works. (upto roof of ground floor) |
| 9 | At 1st. Floor |
| 10 | Reinforcement for reinforced concrete work in the all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection complete as per drawing and direction. i) For works in Foundation and upto roof of ground floor / upto 4M i) Tor steel/Mild Steel I(JSW/JSPL/SHYAM/SRMB/BMASL/ELECROSTEEL/SSL) |
| 11 | At 1st. Floor |
| 12 | 125mm. thickbrickworkwith1st class bricks incementmortar (1:4) i ground floor |
| 13 | G.F. |
| 14 | 1st Floor |
| 15 | G.F. |
| 16 | Neat cement punning about 1.5 mm. thick in wall dado, window, sills, floor, drain, etc. |
| 17 | M.S. structural works with hollow sections ( square or rectangular shape) conforming to IS: 806-1957 & IS:1161-1958) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1956 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. a) Span up to 12 Mtr |
| 18 | Supplying , fitting & fixing Zn -Al alloy (55% Al & 45 % Zn) coated ( followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc.complete with 150 mm, end lap & one corrugation minimum side lap.(Payment to be made on area of finished work) a) With 0.5 mm thick sheet |
| 19 | Labour forcurvingC.I. orG.C.I. sheet forcurvedroof etc. (Payment tobemadeonareaof finishedworksdonewiththe curved sheets.) |
| 20 | Supplying,Fitting corrugated Zinc Alluminium alloy coloured sheet ridging fitted with necessary bolts,screws,washer etc complete.(225 mm end lapping) (A) 300 mm lapping each way (a) with 0.60 mm sheet |
| 21 | Holding down bolt with nut including 100 x 100 x 6 mm plate washer at bottom fitted complete and packing the hole with cement concrete or cement grout as directed. |
| 22 | CGST & SGST (18%) |
| 23 | Labour Welfare Cess (1%) |
