Tender For Annual Contract For Repair And Maintenance Of Buildings At 220 Kv Gss, Chittorgarh - Part-A: Building WorksPWD Rajasthan Integrated Building BSR 2022 2 (B-150/13.1) Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead With cement mortar 1:4 ( 1 cement : 4 coarse sand). 3 (B-153/13.29) Repair to damaged RCC slabs, beams and columns etc for strengtheing with cement mortar 1 : 2 in following steps: (i) Choping losse and cracked concrete to required depth, cleaning the exposed surface of steel and concrete with wire brush and sand papering , cleaning of concrete surface with water as necessary and getting dried. (ii) Applying Epoxy primer on the exposed steel bars. (iii) Applying Epoxy hardener and resin mix (as per manufectureds specification) on concrete and steel bars with brush. (iv) Speading dry cement mortar 1 : 2 mix over epoxy treated wet surface and allow it to dry for one day. (v) Plastering the surface with CSM 1:3 upto depth of 30mm complete. (vi) Cure the plastered surface for 15 days. 4 (B-145/12.43.1) Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provision. New work. 5 (B-151/13.12) Repair to stone masonry in cement sand mortar 1:6 with old & new stones. 6 (B-86/7.12) Providing and fixing Ist quality standard White Ivory Glazed Tiles ISI marked [IS:13753] of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster). 7 (B-86/7.13) Providing and fixing Ist quality MAT finished ceremic tile size 300x300mm confirming to IS : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slsurry including nicely finished joints using water proof joint filler power (Untile or Roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (Including the cost of cement mortar bed). 8 (B-87/7.18.2) P&F 1st quality vitrified porcelain polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1:4 including grouting the joints with white cement and matching pigment etc complete. Size 600 mm X 600 mm. 9 (B-159/14.23.1) Dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: For thickness of tiles 10mm to 25mm. 10 (B-93/8.13.2.1+B-93/8.14) Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure A: 30 mm thick. Commercial Veneer both side. Extra for providing external lipping with 2ndclass teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured). 11 (B-91/8.5.2.3 + B-93/8.11) Providing and fixing fully panelled /partly panelled double leaf shutters frame for windows and ventilators as per approved design and drawings with approved steel fittings as per Annexure A and width of styles, bottom and top rails 75mm including intermediate rails 50 mm wide, beading of 25mm x 15mm size on both faces: 30 mm thick. Shesham wood grade-I. Deduct for providing Single leaf shutter instead of double leaf. 12 (B-92/8.6.8) Providing and fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Wire gauge 24 gauge 14 mesh of IS 1568-1970 marked 85 gauge of dia 0.56 mm. 13 (B-100/9.17+B-101/9.17.1) Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings as per direction of engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint. Add extra for double leaf shutters. 14 (B-152/13.24) Labour charges for repair to door/window without using any material such as applying randha (finishing) tightening of bolts & screw etc. 15 (B-152/13.23) Repair of existing steel glazed doors, windows and ventilator, MS sheet door, garage doors, compound wall gates etc. by welding drilling complete include. Cost of welding rods and hire charge of welding meachine and TP etc complete. 16 (B-154/13.33) Repair of door, window shutters including cost of material and labour for change of damaged : 17 (B-154/13.33.c.i) Aldrop of mild steel. 12 long x12mm dia. 18 (B-154/13.33.d.ii) Stopper of Aluminium with double rubber gutka. 19 (B-154/13.33.f.ii) Steel hinges. For wooden chowkhat 4 size. 20 (B-154/13.33.h) Steel locking bolt. 21 (B-154/13.33.i) Steel handle 6 size. 22 (B-102/9.26) Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 23 (B-150/13.4.1) Renewing glass panes, with puty and nails wherever necessary: float glass panes of thickness 4 mm. 24 (B-99/9.8) Providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 25 (B-172/15.30) Providing & applying one coat of UV resistant polymer cement based waterproofing slurry coating of approved make and quality on concrete or plastered surface as per specifications including preparation of surface by cleaning brushing and dust removing, filling of cracks and making the surface leak proof by mixing one part of chemical with 2 parts of cement and 2 parts of water (covering area 1.86 Sq.M/Kg of chemical) including cost of cement, labour, tools & plant, scaffolding if necessary etc., complete as directed by Engineer in Charge. 26 Part-B: Sanitary WorksPWD Rajasthan Integrated Building BSR 2022 27 (S-240/2.37) Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge (Exposed on wall). 28 (S-240/2.37.1) 15 mm nominal size. 29 (S-240/2.37.3) 25 mm nominal size. 30 (S-15/2.2.6) P&F G.I. Pipes (External Work) with G.I. fittings (IS:1239 Mark) including trenching & refilling earth etc. B Class. 50 mm Dia Nominal bore. 31 (S-233/2.15) P&F Full-way valve (IS:778 Mark) or wheel valve of approved make: 32 (S-19/2.15.1) Gun-metal 15 mm nominal bore 33 (S-19/2.15.3) Gun-metal 25 mm nominal bore 34 (S-234/2.15.6) Gun-metal 50 mm nominal bore. 35 (S-236/2.26.3) P&F PVC Storage Tank ISI Marked (IS : 12701) indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 litres Capacity. 500 litres Capacity. 36 (S-232/2.7) P&F Bib Cock (IS : 8931 Mark), Superior quality of approved make: 37 (S-232/2.7.4) C.P. Brass bib cock, Long Body, 15 mm nominal bore weight not less than 690 gm. 38 (S-232/2.7.3) C.P. Brass bib cock 15 mm nominal bore. 39 (S-225/1.55.3) P&F Bath Shower of approved quality/make. C.P. brass of Heavy & superior quality, revolving with adjustable key 150mm. 40 (S-232/2.8.4) P&F Stop Cock (IS :8931 Mark), superior quality & of approved make: C.P. Brass 15 mm nominal bore. 41 (S-226/1.59) P&F Jet spray for water closet with C.P. Copper Tube flange of approved make. 42 (S-218/1.7.4) P&F water closet Seat Covers with brass hinges complete: Non-breakable of other approved make white. 43 (S-219/1.20.2) P&F Low level Flushing Cistern of 10 litres capacity (IS:2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall : PVC with PVC bend as per IS : 7231. 44 (S-223/1.45.1) P&F looking mirrors with PVC frame of approved (atul/equivalent). Size 500x400mm. 45 (S-222/1.43.1) P&F waste pipe with all fitting : PVC with C.P. Nut 32mm. 46 (S-233/2.13.3) P&F 15 mm Dia Connection Pipe of approved quality/make: PVC pipe with C.P. Brass nuts up to length 450 mm. 47 (S-224/1.48.2) P&F Grating of approved quality/make: Stainless steel sheet heavy duty of approved quality/make size. 125 mm dia. 48 (S-257/3.44.2) Providing and fixing unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type `B for sciland waste dischareg system (IS : 13592: 1992 marked) of approved quality/ make. 110 mm dia. 49 (S-257/3.45) Providing and fixing unplasticized Poly Vinyl Chloride (UPVC) SWR pipe fittings type `B for sciland waste discharge system (IS : 13592: 1992 marked) of approved quality/ make. 110 mm dia. 50 (S-257/3.45.4.ii) Bend 87.5 51 (S-258/3.45.12.ii) Pipe Clip 52 (S-251/3.21.1) Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame. 53 (S-250/3.19.1) Construction of manhole in all type of soil inner size 90 X 60 Cm, 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. Depth up to 0.5 M. 54 (S-247/3.16.4) P&F rigid PVC Pipe (IS:4985 mark) class II / (4 Kg/cm2) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 160 mm dia. 55 Part-C: Electrical WorksPWD Rajasthan Electrical BSR 2022 56 (E-7/3.1) Wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) on surface ISI marked (IS:14927 P - II) virgin material UPVC trunking & its accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box, 10 A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose/holder /3 way Connector, screws, making connections, testing etc. as required. 57 (E-7/3.1.1) Short point (up to 3 mtr). 58 (E-7/3.1.2) Medium point (up to 6 mtr). 59 (E-7/3.1.3) Long point (up to 10 mtr). 60 (E-8/3.3.1) Wiring of 3/5 pin 6 amp. light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC Trunking & its accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box, modular 10A switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. On board. 61 (E-9/4.1) Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. 62 (E-9/4.1.2) 2 x 1.5 sq.mm. 63 (E-9/4.1.6) 2 x 2.5 sq.mm. 64 (E-8/3.4.2) S&F following sizes of ISI marked (IS:14927 P-II) virgin material UPVC trunking along with accessories like coupler, inner, outer, elbow, square box, tee, end cap etc. on surface with screws, expansion fasteners as required. 25 mm x 12 mm. 65 (E-87/17.2.2) Providing & Fixing of energy efficient direct fit (Retrofit)Polycarbonate/ GlasshousingSMD Mid Power LED tube rod(with integral driver & alumn. heat sink ), on existing fixture.system lumen efficacy ≥ 100 lm/Watt output, internal surge protection of 2.5 KV ,THD < 20% ,p.f.≥0.95,CRI >80 , life time of minimum35000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. 1200mm, Min. Lumens output 2000 lm LED Tube rod with Polycarbonate Housing. 66 (E-81/15.7.3) Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceilingfan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ). 67 (E-29/7.20) Providing & Fixing of IS 11037:1984marked non modular socket size flush type 120 watt rotary minimum 5 step fan regulator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required. 68 (E-27/7.4) Providing & Fixing of 16 amp. combined flush type non modular socket and switch set with indicator and fuse set as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. 69 (E-28/7.10) Providing & Fixing of 3/6 pin 16 amp flush type non modular socket made out from Industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. 70 (E-27/7.1) Providing & Fixing ISI marked (IS:3854) 6 amp. flush type non modular switch with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. 71 (E-30/7.26) Providing & Fixing of ding dong/musical chime bell as per PWD specification for electrical Works, including making connection testing etc. as required. 72 (E-17/6.1.1.2) Providing & Fixing of 240/415V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. Single pole MCB (with B/C curve tripping characteristics). 6A to 32A rating.
