Tender For Repairing Work Of Sewer Shaft At Epfo, Ujjain - Dismantling & Demolishing 2 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 3 Of area beyond 3 sq. metres 4 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge 5 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 6 In Cement mortar 7 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per directionof Engineer - in - charge. 8 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 9 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. 10 Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps : 11 Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. 12 Dismantling stone slab wall/flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. 13 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 14 Brick and plaster work 15 Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinth level : 16 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 17 Brick work with comman burnt clay F.P.S.(non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V leveling all shapes and sizes in . cement mortar 1:4 (1 cement :4 coarse sand ) 18 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. 19 With cement mortar 1:4 (1cement: 4 coarse sand) 20 Washed stone grit plaster on exterior walls height upto 10 metreabove ground level, in two layers, under layer 12 mm cement plaster1:4 (1 cement : 4 coarse sand ), furrowing the under layer withscratching tool, applying cement slurry on the under layer @ 2 Kg ofcement per square metre, top layer 15 mm cement plaster 1:1/ 2:2(1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size),in panels with groove all around as per approved pattern, includingscrubbing and washing the top layer with brushes and water to exposethe stone chippings ,complete as per specification and direction ofEngineer-in-charge (payment for providing grooves shall be madeseparately). 21 Providing and fixing on wall face unplasticised Rigid PVC rain waterpipes conforming to IS : 13592 Type A, including jointing with sealring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 22 100 mm pipe 23 Providing and fixing unplasticised -PVC pipe clips of approved designto unplasticised - PVC rain water pipes by means of 50x50x50 mmhard wood plugs, screwed with M.S. screws of required length,including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. 24 110 mm 25 Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 26 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 27 Finishing work 28 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of requiredshade and colour all complete to achieve even shade and colour : 29 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre 30 Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete. 31 Providing and fixing double scaffolding system (cup lock type) onthe exterior side, up to seven story height made with 40 mm diaM.S. tube 1.5 m centre to centre, horizontal & vertical tubes joiningwith cup & lock system with M.S. tubes, M.S. tube challies, M.S.clamps and M.S. staircase system in the scaffolding for workingplatform etc. and maintaining it in a serviceable condition for therequired duration as approved and removing it there after .Thescaffolding system shall be stiffened with bracings, runners,connection with the building etc wherever required for inspection ofwork at required locations with essential safety features for theworkmen etc. complete as per directions and approval of Engineerin-charge .The elevational area of the scaffolding shall be measuredfor payment purpose .The payment will be made once irrespective ofduration of scaffolding. 32 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. 33 Old Work or more coats on new work 34 Providing and fixing powder coated aluminium work (minimum thicknessof powder coating 50 micron) consisting of tee/ angle sections, ofapproved make conforming to IS : 733 in frames of false ceiling includingaluminium angle cleats with necessary C.P. brass/ stainless steel sunkscrews, aluminium perimeter angles fixed to wall with stainless steel rawlplugs @ 450 mm centre to centre and fixing the frame work to G.I. leveladjusting hangers 6 mm dia. with necessary cadmium plated machinescrews all complete as per approved architectural drawings and directionof the Engineer-in-charge (level adjusting hangers, ceiling cleats andexpansion hold fasteners to be paid for separatel 35 Providing and fixing glazing in aluminium door, window, ventilator shuttersand partitions etc. with EPDM rubber / neoprene gasket etc. complete asper the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item): 36 With float glass panes of 5 mm thickness (weight not lessthan 12.50
