Tender For Certain Repair To Leakage, Seepage And Dampness In Md/Otm Accn At Zone-I Under Age B/R-I At Amritsar Cantt; 1 Taking down cement plaster of any thickness from walls/ceiling including raking out joints hacking for key scrubbing down with water and dispose off debries out side the premises where directed complete. 2 Material and labour for rendering 15mm thick on internal brick or concrete surfaces in CM 1:6 , finished even and fair without using extra cement and incl highly stretchable, durable and hydrophobic, Nano/micro technology based Elastomeric Hydrophobic Powder/admixture (EHP) powder @ 1% of cement content complete all as specified and directed.Note : Elastomeric Hydrophobic Powder/admixture (EHP) shall be measured and paid as Supply only in respective item. 3 Material and labour for rendering 15mm thick on external brick or concrete surfaces in CM 1:4 , finished even and fair without using extra cement and incl highly stretchable, durable and hydrophobic, Nano/micro technology based Elastomeric Hydrophobic Powder/admixture (EHP) powder @ 1% of cement content complete all as specified and directed.Note : Elastomeric Hydrophobic Powder/admixture (EHP) shall be measured and paid as Supply only in respective item. 4 Material and labour for rendering 5mm thick on fair face concrete surfaces in CM 1:3, finished even and fair without using extra cement and incl highly stretchable, durable and hydrophobic, Nano/micro technology based Elastomeric Hydrophobic Powder/admixture (EHP) powder @ 1% of cement content complete all as specified and directed.Note : Elastomeric Hydrophobic Powder/admixture (EHP) shall be measured and paid as Supply only in respective item. 5 Making & Laying for Damproofing to wall with 2 component acrylic polymercementitious waterproofing elastomeric coating,mix to form uniform slurry and apply with paint brush:-Taking DownTaking down cement plaster including raking out brick joints properly & make sure the surface is neat & clean & dust free.Surface PreparationFirst,break and remove any damaged or loose plaster or disturbed portion.Clean the brick joints properly and make sure the surface is neat and dust-free.Joint Filling & RepairOnce the surface is completely dry,fill the joints and repair the surface using amixture of acrylic waterproofing chemical and cement mortar ratio 0.5:1:4 (Chemical:Cement:Sand) . Make the surface smooth and let it dry completely.First Coat ApplicationApply the first coat of waterproofing by mixing acrylicchemical with neat cementina1:2 ratio. Use a brush for even application. Allow it to dry properly.Fiber Mesh & Waterproofing CoatAfter the first coat dries,fix the fiber mesh on the surface.At the same time,apply the 2-component ready-made waterproofing material over the mesh.FinalWaterproofing CoatOnce the second coat dries, apply the third and final coat of the 2-component waterproofing material.This coat should fully cover the fiber mesh and provide a smooth surface.Sand SprinklingWhile the final coat is still slightly wet,sprinkle coarse sand over it to provide grip for plaster.Plaster & Paint After the waterproofing layer dries completely,proceed with making & laying cement plasteron surface, 12-15mm thick, in ration 1:4, even & smooth without using extra cement. Note : Quoted rate shall be deemed to be inclusive of materials all labours, tools and plants, scaffolding and working upto height 12 m etc. Make :- Fosroc,Sika,Choksay,Bostik,STP,I can Nano,Asian Paints ,Berger,Dr Fixit 6 Supply only Nan/ micro otechnology based Elastomeric Hydrophobic Powder/admixture (EHP) powder for cement plaster and concrete all as specified.Make:-Narolac,I can Nano,Asian Paints ,Berger,Dulux,Shalimar,JK ,Fosrc,Sika,Dr Fixit 7 Material and labour for preparation of newly plastered surfaces of walland applying 02 coats of High Penetration, water resistance, anti bacterial, Nano/micro technology based Premium Waterproof Nano Cement Paint of having zero VOC over one coat of nano Primer complete all as specified & directed.Make:-Narolac,I can Nano,Asian Paints ,Berger,Dulux,Shalimar,JK 8 Material and Labour for preparation of newly plastered surface of wall and applyingtwo coats of Nano/ micro technology based Acrylic Regular Distemper, water based gives walls a smooth and matt finish and applied on prepared surface of wall & ceiling over a coat of approved nano primer @ 6.50 sqm/ltr using AUTO-ROLLER complete all as specified and dircted by Engr-in-Charge.Make:-Narolac,I can Nano,Asian Paints ,Berger,Dulux,Shalimar,JK 9 Material and Labour for preparation of new plastered surfaces and applying three coatsof white washon ceiling complete all as specified. 10 Preparation of existing roof surface of concrete/PCC tiles/brick tiles/Chajja/Parapet surfaceby cleaning with Nano bio wash or equivalentincl wire brush including scrapping & cleaning with emery paper or by air blasting or sand blasting for removing any foreign materials, loose concrete/aggregate etc complete all as specified and as directed. 11 Material and labour for average 25mm thick PCC 1:2:4, type B0 (using 12.5mm size stone aggregate) as levelling course, padding on chajjas, etc incl angular moulding at junction upto 10cm heightwith proper slop towards the spouts/drain pipe complete all as specified with WPC @2% by wt of cementas per manufacturers instruction, applied over prepared surfaces as per directedby Engr in Charge.WPC Make :- Fosroc,Sika,Choksay,Bostik,STP,I can Nano,Asian Paints ,Berger,Dr Fixit 12 Material and labour for appplying Nano/micro technology based Anti-corrosive with high strength carbon Fiber based shorter chain Epoxy coating (Bond Coat) or equivalentof finest quality, high strength, high penetration, durable, UV resistant, high scratch/ impact resistant, bacteria resistant and thermally stable, Semi transparent, mixed in proportion (4 Base : 1 Hardner)in reqd consistency @ 8 sqm/kg over the entire prepared surfaces of roof/parapet complete all as specified.Make :- Fosroc,Sika,Choksay,Bostik,STP,I can Nano,Asian Paints ,Berger,Dr Fixit 13 Providing and applying of polyurethene (white)liquid roof waterproofing with improved water ponding capability, thermal insulating elastomeric high build liquid membrane for concrete roof for exterior wall and exposed surface with solid content not less than 80% and solar reflective index 109 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film,14 days,+30 degree C) (ASTM D 624) and tensile strength ˃= 2 N/mm2 (ASTM D4541) (a) Apply first coat of Polyurethene white @ 650 gram /Sqm (minimum) of approved brand by brush / roller while primer surface is tacky.Spread waterprrofing glass fibre mesh of 45 GSM with overlap of 50 mm in both directions when the surface is still ticky.Allow 1st coat to dry.(b) Apply 2nd and 3rd coat of polyurethenewhite @ 650 gram /Sqm (minimum) of approved brand by brush or roller .Make :- Fosroc,Sika,Choksay,Bostik,STP,I can Nano,Asian Paints ,Berger,Dr FixitNote :- (i) The minimum dry film thickness (DFT) of roof treatment shall be 2 mm if any shortfall in thickness of above treatment the same will be achieved by additional coat.(ii) The procurement of material and execution of work of water proofing treatment shall be carried out by authorised applicator approved by GE under company supervision on weekly basis during the currancy of work.(iii) The material brought at site as per consumption kept in record and empty buckets/Containers will be deposited in the store yard before preparation of every Running Account Recipt (RAR) .(iv) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 5 years. 14 Supply and fixingin reapir 15mm bib tap standard of PTMT any colour fancy type long body high pressure screwed for iron pipe and fixed (minimum weight 15 mm- 105 gms) etc complete all as specified and directed. 15 Supply and fixingin reapir 15mm angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 15 mm- 90 gms) complete all as specifeid and directed. 16 Ditto as per item above here-in-before but with long shank & cup (concealed type) minimun weigth 15mm-110gms) complete all as specified. 17 Supply and fixingin repair 100mm swivel type shower rose of PTMT with shower arm15 mm size, 195 mm long ofany colour for fixing with 15 mm pipe ( min weight 40 gms )complete all as specified and directed. 18 Supply and fixingin repair 15mm Pillar taps,of PTMT any colour fancy type high pressure scewed for iron pipe complete all as specifeid 19 Supply and fixing in repairs bevelled edge mirror ofsize 600mmx450mm , 6mm thick of selected quality glass, mounted on 6mm thickcommercial plywood including teak wood beading allround and fixed to wooden plug with chromium plated brass screw and cup washer and including clamps with wooden / plastic frame complete all as specified 20 Supply and fixingin repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified 21 Supplying and fixing in reapir whitePVC valve less syphonic action type low level flushing cistern of 10 ltrs capacity with inlet ball valve, float valve, push button type handle includingpipe 32mm dia of PVC(Heavy duty) flush pipeincluding brackets andtaking down/dismantling old unserviceable cistern completeall as specified. 22 Supply and fixingin repair vitreous china wash basin, white, flat back of size 550mm x 400mm fixed on existing brackets, including32mm bore CP waste coupling, PVC waste pipe, inlet & outlet, chrimium plated PVC pipe etc, complete all as specified and directed by Engineer-in-Charge. 23 Supply & fixing in replacement vitreous China squatting pan Orissa pattern of size 580mm x 440mm white with integral foot rests including lime concrete for fixing the trap and making connection to trap and flush pipe and making good the floor to existing specifications completeall as specified and directed. 24 Supply and fixingin repair replacement vitreous china wash down water closet pan (pedestal pattern) white with trapincluding connection to existing out joint pipe, flushing pipe or cistern, antisyphonage pipe, includingplastic water closet seat white closed pattern with flat botom and cover mild steel chromium plated or aluminium plated or aluminished hinging device complete all as specified and directed. 25 Supply and fixingin reapir soap dish fixed to walls with chromium plated brass screws complete all as specified. 26 Supply and fixingin repair PVC connection 450mm long of 15mm size with PTMT nutson both sides complete all as specified. 27 Dismantaling floor hearth or wall tiling incl cement mortar bedding or plaster upto the thickness of 15 mm complete removing rubbish off the premises complete as specified. 28 Material and LabourNon skid cerermic coloured tiles 7 to 8 mm thick (Square /rectangular) area of each tile exc. 0.11 sqm but n.exc. 0.18 sqm, set and jointed in neatcement slurry and pointed in white or coloured cementwith pigment to match over 20mm thick screed bed in cement mortar (1:6) complete all as specified and directed. 29 Material and LabourGlazed ceramic coloured tiles in vertical surface 350x 450X 300X 7mm thick setandjointedinneat cement slurry and pointed in white or colour cement to match such skriting /dado and over 10mm thick in cement mortar 1:4 as in backing plaster complete all as specified and directed. 30 Taking up or down steel water tubing and connectionsincluding cleaning serviceable pipe for refixing and removal of unserviceable pipe, bore of pipe 15mm complete all as specified.Note :- The quoted rates shall be include for necessary excavation andearth work, cutting/ chasing in wall/ floor and making good in CM1:3 all as directed. 31 All as per above item here-in-before but 20 mm bore. 32 Supply and fixing 15mm boretubes medium grade , galvanised, with all fittings, and fixed complete to walls and ceilings or laid in floorscomplete all as specified. 33 Supply and fixing20mm bore tubes medium grade , galvanised, with all fittings, and fixed complete to walls and ceilings or laid in floors complete 34 Supply and fixingrotational moulded polythelene water storage tanks(multi layer) capacity 500 litres(cylindrical vertical with closed top), with and including 20mm dia PTMT ballvalve with epoxy coated aluminium rod ( minium weight 210gms ) hoisted, fixed in position and making connection with inlet & outlet tank nipple with gate valveincluding dismantling of existing unserviceable tank exc 250 Ltr & not exc 500 Ltr complete all as specified. 35 Disconnecting existing tanks of cap exc 250 ltrs & n.exc 500 Ltrs, setting aside (or lower ing if required) for repairs, cleaning, etc. and hoisting if required re- connecting and re-fixing in position and Cleaning and removing all scale and dirt, etc. from tanks and form mouths of circulating pipes,including inlet & outlet tank nipples and inlet and outlet gate valave etc complete all as specified and directed. 36 Supply and fixingin reapir PVC covers of water storage tank (Capacity of tank n.exc 500 Ltr) area not exceeding 0.5 sqm each including hing and fixing nut bolt arrangement complete all as specified and directed. 37 Supply and fixingin repair 15 mm Ballvalveshigh pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for ironpipe and fixed.(Minimum weight 15mm-142gms) 38 Supply and fixingin repair 20 mm Ballvalveshigh pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for ironpipe and fixed.(Minimum weight 2 0mm-210gms) 39 Dismantling ofPVC pipeof 75/100mm dia fixed with cement joint complete all as spec ified. 40 Material and Labour75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete. 41 Supply and fixingPVC (SWR) 110mm dia mtr pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete. 42 Supply and fixingPVC (SWR) 110mm dia mtr bends any radius complete. 43 Supply and fixingPVC (SWR) 100mm junction single,(Single T) equal or unequal 44 Supply and fixingPVC (SWR) 100mm junction double, (double T) equal or unequal 45 Supply and fixingPVC (SWR) 75mm junction single,(Single T) equal or unequal 46 Supply and fixing75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. 47 Material and LabourPVC (SWR) gully trap 125/110mm setting and jointing with solvent cement. 48 Taking down shutter and removing from site of any description size but not exc 1 sqm complete all as specified and directed. 49 Taking down chowkhats or frame without taking of shutter and removing from site n.exc 1.5sqm each complete all as specified and directed. 50 Taking down shutter exc.1 sqm and not exc 4 sqm each and refixing same opening complete. 51 Supply and fixingsolid PVC door frame of size 50mmx47mm made out of 5mm plain glover PVC sheet reinforced with MS square tube in opening as per specification. 52 Supply and fixingfactory made soilid panel PVC Door shutter 30mm thick (Stype) consisting of frame made out MS frame shall be covered with heat moulded plain coloured PVC C channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, & bottom rail; Panneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification. 53 Material and Labour for Box type steel ventilator made of ERW tube P-section of size 60mmx25mmouterframe ( single rebated), comprisesglazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing ofsheet glassincluding fixture and fittingslike as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. NOTE : , Guard bar, Sheet glass and painting shall be measured and paid Separately. 54 Supply and fixingframed work such as grill, framed guard bar and similer work conforming to FE 290, GDE E- 165 all as specified and as directed. 55 Supplying and fixingstainless steelwire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified. 56 Supplying and fixing in repair stainless steelwire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified. 57 Hacking out old broken glass any thickness, size, quality or description from steel frames with oil glazing pin, glazed with putty or fixed with beads Complete all as specified 58 Supply and fixing3mm thick ordinary sheet glass and glazing with oil putty or fixed on steel frame, in squares not exc 0.50 Sqm in each panes complete all as specified. 59 Supply and fixing 3mm thick figured glass pin head type and glazing with oil putty or fixed on steel frame, in squares not exc 0.50 Sqm in each panes complete all as specified. 60 Supply and fixingbutt hinges 100mm size medium weight cold rolled mild steel fixed with stainless steel screw complete all as specified and directed 61 Supply and fixing150 mm size aluminium anodized barrel tower boltof extruded section fixed with stainless steel screw complete all as specified. 62 Supply and fixingin reapir 150 mm size aluminium anodized barrel tower boltof extruded section fixed with stainless steel screw complete all as specified. 63 Supply and fixing125 mm size extruded aluminium anodized handle cast type fixed with stainless steel screw complete all as specified. 64 Supply and fixing in repairs125 mm size extruded aluminium anodized handle cast type fixed with stainless steel screw complete all as specified. 65 Material and Labourfor preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide premier. 66 All as per above item here-in-before but single coat on old steelsurfaces incl preparation complete as specified. 67 Demolition of cement concrete in ground floors and pavings (unreinforced) n.exc 15 cm thickness (below or above ground level) all as directed 68 Material and Labourcement concrete type C-1, 1:3:6 ( using 20mm graded stone aggregate) , 50 mm thickas in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair ontop without using extra cement complete all as specified and directed. 69 Demolition of cement Concrete in sunken floors exc 15cm thick ( above ground level) and disposing the rubbish debries out side the premises where directed complete. 70 Material and LabourPlain cement concrete (1:5:10) type E-2 using 40mm graded stone aggregate as in sunken filling as mass concrete of sunken complete all as specified. 71 Material and labour for water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WCs etc shall be as under:-(a) Application of two component acrylic modified cementitious coating on dried surface free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance existing coating and achieve a gripping profile that is clean, dry and free from laitance and any other form of surface contamination. The installation instructions in manufacturers literature should be strictly complied with including but not limited to the following:-(i) Chipping out any visible cracks in V-Groove pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/ Dr. Fixit 302 SBR latex/ perma latex SBR/ FOSROC Nitbond SBR latex/ Asian paint latex as required. Final cleaning of surface with powder grinder, wire brush, hair brush & vacuum pressure.(b) Dampen all surface immediately ahead of application of acrylic modified cementitious coating of SIKA top seal-107/ Brush bond FOSROC/ Dr. Fixit/ STP/ CICO.(c) Whilst the surface is still damp from saturation (SSD) apply one coat of acrylic modified cementitious coating of SIKA top seal-107/ Brush bond FOSROC/ Dr. Fixit/ STP/ whilst of the first coat is wet.(d) Apply glass fabric sheet of SIKA Fab 1/ FOSROC/ Dr. Fixit/ STP whilist the first coat is wet.(e) Once touch dry, apply second coat of acrylic modified cementitious coating of SIKA top seal-107/Brush bond FOSROC/Dr. Fixit/STP/CICO of viscosity as per manufacturer ins on the entire area.(f) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat.(g) The waterproofing coating should be taken to a height minimum 450mm above the finished floor level on the vertical surface.(h) It is essential to cure acrylic modified cementitious coating immediately after application (min 6-8 hrs drying) for a min of 3 to 5 days to ensure full cement hydration and to minimize cracking. 72 (j) A protection plaster (12-15mm thick) in cement mortar (1:3) admixed with appropriate integral water proofing compound has to be a applied on the walls.(k) Admixture: Sika plastocrete plus/ FOSROC/ Dr. Fixit/ STP/ CICO confirming to IS 2645.(l) Providing and applying a protection screed 50mm thick in cement mortar (1:4) mixed with SIKA plastocrete over the applied water proofing coating on horizontal surfaces.(m) Admixture: Sika plastocrete plus/ FOSROC/ Dr. Fixit/ STP/ CICO confirming to IS 2645.(n) All the corners and joints should be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansion zone in the centre of make seal tape SIKA/ FOSROC/ Dr. Fixit/ STP.(o) The membrane has to be protected in accordance with the manufacturers recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturers recommendations.(p) Water proofing treatment has to be carried out through authorised applicators.(q) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (r) All traps in sunken slabs to be enclosed with PCC (1:1½:3) (min 15cm) alround. (s) The sunken portion shall be filled with PCC (1:5:10) using 40mm graded stone aggregate all as specified. (t) Providing drainage spout pipe GI 40mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600mmlong) including cutting hole in existing wall and making good the disturbed surface complete all as specified and directed.(u) Providing 25mm thick cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as sin flooring for laying floor finishes all as specified. Notes :- (i) Item No. (s), (t) and (u) shall be measured and paid seperately. (ii) Plan area (wall to wall/ wall to beam/ beam to beam) shall be measured and paid. No separate measurement for vertical surface shall be accounted and quoted rate shall be deemed to include for the same. 73 Material and Labourfor preperation ofOLD decorated surfaces of walls by scraping and washing down with, removing all acales/dirts and greasy spots andapplying one coat of oil bound distemper over and incl incl applying plaster of paris putty of 1mm thickness to prepare the surface even and smooth complete all as spcified and directed by Engr in Charge . 74 Material and Labourfor applying one coat of whitewash on ceiling including preperation of OLD plastered surfaces complete all as specified and directed. 75 Material and LabourPreparing of OLD decorated brick/concrete plastered/un-plastered surfaces including scrapping of old existing treatment of walls pillars cornices applying one coat of cement base paint and making smooth surface complete all as specified and directed. 76 Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. 77 Supply & Fixing Bib taps, cast copper alloy fancy type, chromium plated, with long shank long bodyfor sink with crutch or butterfly handle, screwed down, screwed for iron pipe of size 15mm bore ; Complete all as specified and directed by Engineer - in - Charge. 78 S/F 15mm bore anglecock cast copper alloy CP screweddown high pressure with crutch or butterfly handle complete. 79 Supply and fixingin repair stop valves(Concealed cock) 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc. complete all as specified. 80 Material and labour for providing and placing in position free flow non shrink cementitious micro Nano-concrete of Grade M-50 for effected RCC beam, column, chajjas, fins/drops, staircase, etc. complete using necessary formwork (where applicable) after due treatment/coating of existing concrete with High Penetration, high adhesion shorter chain Nano epoxy bond adhesive and reinforcement surfaces with High Penetration, high adhesion shorter chain with high anti corrisive Nano Epoxy Zinc rich primer. Make :- Fosroc,Sika,Choksay,Bostik,STP,I can Nano,Asian Paints ,Berger,Dr FixitNote : (i) Nano micro-concrete shall have a min 1 day compressive strength of 10 Mpa and 28 days strength of 50 Mpa incl min tensile strength of 5N/mm² at 28 days and min flextural strength of 5N/mm² at 28days. (ii) Nano micro-concrete shall be prepared in proportion of (1Part) Nano cement : (0.5 Part) Sand (packed graded sand of same make) : (1 Part) Aggregate (packed graded sand of same make) : (0.1 Part) Nano shorter chain water based epoxy base : (0.1 Part) Nano shorter chain water based epoxy Hardener : (0.002 Part) Nano Admixture : (0.3 to 0.4 Part) Water : (0.01 Part) EHP Powder.(iii) Necessary formwork shall be removed after 48 hrs and curing shall be done as per manufacturer instructions.(iv) Necessary formwork upto the height of 15 mtrs, TMT bars (where reqd), treatment with High Penetration, high adhesion shorter chain Nano epoxy bond adhesive and High Penetration, high adhesion shorter chain with high anti corrisive Nano Epoxy Zinc rich primer shall be included in quoted rate. 81 Material and labour for applying two component structural grade Shorter Chan NANO/MICRO Base and Catalyst basedpolymer modified reinstatement mortar in damaged parapets /chajjas/staircase, where local spalling has taken place or shuttering is not possible. The morter can be applying in layers not exceeding 6mm thick in each layer in and upto any thickness in smaller vertical pockets and upto any thickness in horizontal applications (any RCC ceiling surfaces)till the desired shape and size. The mortar should have a minimium compressive strength 12N/mm2 in 1 day and 45N/mm2 in 28 days. Minimum flexural strength should be 8 N/mm2 in 28 days. A modified styrene butadience emulsion for use as a bonding aid and gauging liquid for cementious system to be mixed with cement slurry before the application of modified polymer mortar. The bonding agent should have minimium compressive strength 24N/mm2. Minimum tensile strength 3.5N/mm2, minimium flexural strength 6.5N/mm2 complete all as spd and directedby the Engr-in-charge.Make :- Fosroc,Sika,Choksay,Bostik,STP,I can NANO/MICRO,Asian Paints ,Berger,Dr Fixit 82 Taking down carefully copper/aluminium point wiring any type (light, fan, socket or power) complete including fittings such as switches, sockets, ceiling roses, lamp holders, regulators, sockets etc. and removing old retrieved materials to store for keeping in safe custody or for taking credit (credit for above items shall be made as per condtitions separately) complete all as specified and directed. 83 Material and Labour forpoint wiring in existing concealed conduit for the following point (using red, black, green colour wires as colour codings) complete with 1.5 sqmm ( nominal cross section area ) single core FRLS PVC insulated unsheathed and multi stranded copper conductor cable 1100 volt ( ISI marked ) drawn through and existingPVC concealed conduit with all fittings and accessories including pressed steel powder coated sunken terminal box suitable for Modular switch socket ( min 50mm deep and 1.6 mm thick sheet ,suitable size ) concealed in wall , including inner and outer plates ( cover plate ) suitable for fixing the modular switches/sockets/regulator etc including provn of 1.5 sqmm single core FRLS PVC insulated multi stranded copper conductor wire continues as earth wire connected to earth dolly etc including cuttings chases in walls as required and making good disturbed surfaces with cemenr mortar (1:3) as required complete all as specified and as directed for the following :- Note:1. Switch/socket/ceiling rose/lamp holder/regulator etc. shall be measured and paid for separatelya) For one light /fan/ buzzer point controlled by one 5 Amp switch one way 84 b).For one three pin socket outlet 5 Amps independent board complete 85 c) For one three pin 5 Amps socket outlet on the same board with other switches 86 d) For one light point controlled bytwo way switch 87 All a per item No 84here-in-abovebut with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 2.5 Sq mm copper multi stranded conductor connecting to common earth dolly complete. 88 Material and Labour for surface point wiring for the following point ( using red,black,green colour wires as colour codings) complete with 1.5 sqmm ( nominal cross section area ) single core FRLS PVC insulated unsheathed and multi stranded copper conductor cable 1100 volt ( ISI marked ) drawn and including surface PVC conduit with all fittings and accessories i.e. pipe bend,pipe hook, elbow,juction boxes etc including pressed steel powder coated sunken terminal box suitable for Modular switch socket ( min 50mm deep and 1.6 mm thick sheet ,suitable size ) concealed in wall , including inner and outer plates ( cover plate ) suitable for fixing the modular switches/sockets/regulator etc including provn of 1.5 sqmm single core FRLS PVC insulated multi stranded copper conductor wire continues as earth wire connected to earth dolly etc including cuttings chases in walls as required and making good disturbed surfaces with cemenr mortar (1:3) as required complete all as specified and as directed. Note:1. Switch/socket/ceiling rose/lamp holder/regulator etc. shall be measured and paid for separatelya) For one light /fan/ buzzer point controlled by one 5 Amp switch one way 89 b).For one three pin socket outlet 5 Amps independent board complete 90 c) For one three pin 5 Amps socket outlet on the same board with other switches 91 d) For one light point controlled by two way switch 92 All a per item No 89 here-in-abovebut with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 2.5 Sq mm copper solid conductor connecting to common earth dolly complete all as specified and directed. 93 Supply & fixing Modular switch flush type one way 6 Amp, 230 voltscomplete all as specified and directed. 94 Supply & fixing Modular switch flush type two way 6 Amp, 230 voltscomplete all as specified and directed. 95 Supply & fixing Modular socket 6 Amp 2/3 pin combined 2 module complete all as specified and directed. 96 Supply & fixingModular switch flush type one way 16 Amp, 230 voltscomplete all as specified and directed. 97 Supply & fixing Modular socket 6 /16 Amp 2/3 pin combined 2 module complete all as specified and directed. 98 Supply & fixing Modular switch bell push swiwch 6 Amp 1 modulecomplete all as specified and directed. 99 Supply and fixing ceiling rose 65X50 mmthree terminals c complete all as specified and directed. 100 Supply & fixing Lamp holder bakellite type with black plate suitable for batten fitting complete all as specified and directed.. 101 Supply and fixing in replacement of Ding Dong bell AC 230 Volts complete all as specified and directed. 102 Supply & fixing Modular stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd heavy duty 230 voltsc complete all as specified and directed. 103 Supply and fixing in replacement for vertical sheet steel metal enclouser distribution boards, double door factory made3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulatedcopper wire of suitable size from the MCCB to the out going circuits oneincoming MCCB and suitable outgoing MCBs circuits comprising of 3 phase 4 wireof suitable rating complete all as specified and directed including following accessories :- (a) MCCB 100 amps, 25 KA, TP, 415 volts, 50 Hz = 01 No. 104 Supply and fixingin repairs sheet metal enlosure DBs double door factory made flush fixed complete with 200 amps rated bus-bar 240 volts single phase 8 ways including necessary brick work and plaster to match with the existing surface complete all as specified and directed. 105 Supply and fixingin repairs sheet metal enlosure DBs double door factory made flush fixed complete with 200 amps rated bus-bar 240 volts single phase 12 ways including necessary brick work and plaster to match with the existing surface complete all as specified and directed. 106 Supply and fixing in repairs MCB single pole 6 to 32 Amps complete all as specified and directed. 107 Supply and fixing in repairsMCB DP 40 Amps 240V, 10 KA, complete all as specified and as directed 108 Supply and fixing in repairs40 to 63 Amps MCB TPN, 415 Voltcomplete all as specified and directed. 109 Supply and fixing in repairs of Sheet metal single pole and neutral enclosure, 240 volts with a two pin and earth plug and socket complete with one single pole MCB capacity 20 amps complete all as specified and directed (for AC and geyser). 110 Supply and fixingin repairs,Fresh Air fan of size 250mm, Plastic body 1200RPM, electrically driven, 230volts, 50Hz, single phase, AC supply, copper wounddynamically balanced impeller for smooth and vibration free operation, complete with louvers,nuts for fixing exhaust fan and 3 long bolts, nuts for fixing louvers with civil work,wall hole, and provision of PVC insulated, flexible copper conductor cord of size 23/0.0076, three core from ceiling rose to fan all as specified and directed. Note: Material and Labour for Making suitable opening as required for fixing air fan shall be deemed included in the quoted rate of item. 111 Supply and fixing ,in repairsExhaust fan of size 300mm, Heavy duty 1200RPM, electrically driven, 240volts, 50Hz, single phase, AC supply copper wound , dynamically balanced impeller for smooth and vibration free operation, complete with louvers,nuts for fixing exhaust fan and 3 long bolts, nuts for fixing louvers with civil work,wall hole, and provision of PVC insulated, flexible copper conductor cord of size 23/0.0076, three core from ceiling rose to exhaust fan for giving connectioncomplete all as specified and directed. Note: Material and Labour for making suitable opening as required for fixing exhaust fan shall be deemed included in the quoted rate of item. Note for item No-111 &112 : Old retrieved material obtianed shall be deposited in MES Store Yard. 112 Supply and fix in repairsLED tube light 20 watt, (4 long), 6500K, wall mounted, E-lite LED curve with high lumen batten with efficacy not less than of 100 lumens, with integrated electronic driver complete with all accessories complete all as specified and directed. 113 Supply and fix in repairsLED decorative Gate ligh/Garden lights 20 watt light fitting with allaccessories includingmaking connections by using suitable size of PVC wire any type complete all as specified and as directed. 114 Supply and fixing Iin replairsLED building security light fitting powder coated pressure die cast alminium compact High power LED street light with heat resistant toughened glass for 25 watt with IP66 protection and impact resistance of IK07 with 10KV Built-in Surge Protection Devicebracket made out of GI Pipe 40mm medium grade 1.2 mtr long made to shape with fixing clamps of MS Flat 40x6mm nuts bolts Complete all as specified and directed. 115 Supply and fixin repairsSMD/PLUTO NEOLED luminare36/40 watt 600 x 600 mm 220 V ACLED ceiling light recessed/surface type with high efficiency PMMA diffuser soft glass free light complete with driver ,holders and LED lamps stable for roof/ceiling including fixing arrangementsand connecting with copper wire flexible three core 1.5 sqmm PVC insulated 3 core cable from ceiling rose to light fitting complete all as specified and as directed. 116 Supply and fixingin repairsdecorative Ceiling light 12 watt light fitting LED type with accessories including any type complete all as specified and as directed. 117 Supply and fixing in repairs1100 volts grade heavy duty PVC cable insulated aluminium conductor served with inner sheating of PVC tape and over all PVCsheathed in service connection stranded conductor flatr 6 sqmm 2 core cable allas specified and directed and specified 118 Supply and fixing in repairs , Sub main wiring with two single pole 6 sqmm (nominal area) stranded copper conductorFRLS PVC insulated and unsheathed cable drawn inexisting non metalic PVC rigid conduit medium grade of suitable size with all standared fitting ,including one run of continuous PVC insulated standed copper conductor PVC insulated stranded copper conductor FRLS cable 6 sqmm (nominal area) for earth continuty , including taking out and removal of old sub main wiring , complete all as specified and directed.Note:- Two runs of 6 sqmm main cable one run of 6 sqmm for earth cableshall be measured as one unit/ one running metre. 119 Supply and fixing in repairs , Sub main wiring with two single pole 6 sqmm (nominal area) stranded copper conductorFRLS PVC insulated and unsheathed cable drawn inand including non metalic PVC rigid conduit medium gradeof suitable size with all standared fitting , on surface including one run of continuous PVC insulated standed copper conductor PVC insulated stranded copper conductor FRLS cable 6 sqmm (nominal area) for earth continuty , including taking out and removal of old sub main wiring and making good disturbed surface as per exisiting as required, complete all as specified and directed.Note:- Two runs of 6 sqmm main cable one run of 6 sqmm for earth cable & conduit shall be measured as one unit/ one running metre. 120 Supply and fixing in repairs , Sub main wiring with two single pole 4 sqmm (nominal area) stranded copper conductor on surface FRLS PVC insulated and unsheathed cable drawn inexisting non metalic PVC rigid conduit medium grade of suitable size with all standared fitting ,including one run of continuous PVC insulated standed copper conductor PVC insulated stranded copper conductor FRLS cable 4 sqmm (nominal area) for earth continuty , including taking out and removal of old sub main wiring including making good disturbed surface as required as per existing, complete all as specified and directed.Note:- Two runs of 4 sqmm main cable one run of 4 sqmm for earth cableshall be measured as one unit/ one running metre. 121 Supply & fixing in repairs , Sub main wiring with two single pole 4 sqmm (nominal area) stranded copper conductorFRLS PVC insulated and unsheathed cable drawn inand including non metalic PVC rigid conduit medium grade of suitable size with all standared fitting , on surface , including one run of continuous PVC insulated standed copper conductor PVC insulated stranded copper conductor FRLS cable 4 sqmm (nominal area) for earth continuty , taking out and removal of old sub main wiring including making good disturbed surface as required as per existing, complete all as specified and directed.Note:-Two runs of 4 sqmm main cable one run of 4 sqmm for earth cable & conduit shall be measured as one unit/ one running metre. 122 Material and labour in repairsEarthing complete with galvanized steel earth plate electrods of size 60cmx60cmx6mm thick burried directly in ground vertically(earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanized iron or steel earth wire 4 mm dia by means of bolts nuts check nuts and GI washers of Galvanised iron protected by steel pipe 15mm (light grade) all as shown in elecrrical plate No.3 of SSR Part-I and connecting to earthing test point (earth test point to be provided at 5 mtr distance from earth pit) and testing on completion including necessary excavation and earth work. The rate also include charcoal dust and salt in alternate layers 25 mm dia light grade GI pipe, funnel, wire mesh. Concrete 1:3:6 type C-1 for pit and RCC pit cover. The extra cost of the water- ing pipe,bends,elbows shall be included in the unit rate.Note : RCC pit cover shall be precast of RCC 1:2:4type B-1 80mm thick reinforced with XPM weighing notless than 4 Kg/Sqm complete all as specified and directed. 123 Material and Labour forin replacemennt earthing complete with galvanized steel earth plate electrod of size 60cmx60cmx6mm thick burried directly in ground vertically(earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanized iron or steel earth wire 4 mm dia by means of bolts nuts check nuts and GI washers of Galvanised iron protected by steel pipe 15mm (light grade) all as shown in elecrrical plate No.3 of SSR Part-I and connecting to earthing test point (earth test point to be provided at 5 metre distance from earth pit) and testing on completion including necessary excavation and earth work. The rate also include charcoal dust and salt in alternate layers, 25 mm dia light grade GI pipe, funnel, wire mesh, Concrete 1:3:6 type C-1 for pit and RCC pit cover. The extra cost of the watering pipe, bends, elbows shall be included in the unit rate. Note : RCC pit cover shall be precast of RCC 1:2:4 type B-1 80mm thick reinforced with XPM weighing notless than 4 Kg/Sqm,complete all as specified and directed.
