Tender For Repair Of Furniture At Mil Stn Fazilka; 1 TABLE 900 X 600mm with and without Drawer (FD-223 / 284 /224 / 283 /42 /55): Removing of UNSV legs of table 3 X 2 with and without drawer and S&F of new legs as existingof Ist class hard wood . 2 Removing of UNSV long railsof table 3 X 2 with and without drawer and S&F of new long railsas existingof Ist class hard wood 3 Removing of UNSV side rails of table 3 X 2 with/without drawer S&F of new rail as existingof Ist class hard wood 4 Removing of UNSV drawer of table 3 X 2 with drawer and S &F new drawer as existingalongwith chromium plated knobs all as per drg. 5 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces. 6 TABLE CENTRE (FD-29/235/ 274) : Removing of old u/s legs of table centre S&F of new legs as existingof Ist class hard wood 7 Removing of u/s long rail of table centre S&F of new rails as existingof Ist class hard wood 8 Removing of old u/s short rail of table centre and S&F new short rail made out of 1st class hardwoodas shown in the drg 9 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain glossy finish on all the exposed surfaces. 10 TABLE BED SIDE (MAP) (FD/Map/07 & FD/E6/Map/15) :Removing of u/s sideand replacing the same with one side teak faced prelaminatedparticle board 11 Removing the u/sdrawer and S&F new drawer made out of prelaminated partcile board and 12mm thick commercial plywood as specified in drg . 12 Removing the u/s back plywood , S&F new 6mm thick BWR grade plywood commercial as existing. 13 Removing the u/s legs and S&F new legs made out of ms square 18mm pipe with appropriate size screws and matching with black colour with other legs. 14 CHAIR DINING PVC SEAT AND CANE (FD-279/ FD-16,FD- MAP II/05) : Removing the u/s front legs ,S&F new front leg as existingof Ist class hard wood 15 Removing of old u/s Rear legs of Chair dining S&F of new Rear legs as existingof Ist class hard wood 16 Removing of old u/s front rail of Chair diningS&F of new front rail as existingof Ist class hard wood 17 Removing of old u/s Rear rail of Chair diningS&F of new Rear rail as existingof Ist class hard wood 18 Removing of old u/s Side rail of Chair diningS&F of new Side rail as existingof Ist class hard wood 19 Removing of old u/s Back wooden of Chair diningS&F of new Back wooden as existingof Ist class hard wood 20 Removing of old u/s Stiffner of Chair diningS&F of new Stiffner as existingof Ist class hard wood 21 Removing of existing cane cleaning of cane holes and recanning with 2 mm wide new plastic cane for seat and 3.5 mm wide cane for borders of chair all as specified and shown on drg and as directed by Engr-in-charge. (For chair 0.40x0.39 = 0.156 Sqm) 22 Removing old u/s pvc seat from existing chair dining and S&F new PVC seat single piece3mm thick weightnot less than 0.39 Kgswith holes having 4 x 10mm thick ribs mouldedall as specified in drg and as directed. 23 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces. 24 CHAIR DINING CUSHION (FD/MAP/10): Removing the u/s front legs ,S&F new front leg as existingof Ist class hard wood 25 Removing of old u/s Rear legs of Chair dining cushion and S&F of new Rear legs as existingof Ist class hard wood 26 Removing of old u/s front rail of Chair dining cushion and S&F of new front rail as existingof Ist class hard wood 27 Removing of old u/s Rear rail of Chair dining cushion and S&F of new Rear rail as existingof Ist class hard wood 28 Removing of old u/s Side rail of Chair dining cushion and S&F of new Side rail as existingof Ist class hard wood 29 Removing of old u/s Back wooden of Chair dining cushion and S&F of new Back wooden as existingof Ist class hard wood 30 Removing of old u/s Stiffner of Chair dining cushion and S&F of new Stiffner as existingof Ist class hard wood 31 Removing old u/s foam with cushion cover for seat of chair dining cushion and S&F new cool foam with cushion cover and cloh tapestry superior quality,colour ,pattern and quality as approved by GE/Engr -in-charge all as specified in drg . 32 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces. 33 CHAIR WRITING (FD-280/FD-20) : Removing the u/s front legs ,S&F new front leg as existingof Ist class hard wood 34 Removing of old u/s Rear legs of Chair writing S&F of new Rear legs as existingof Ist class hard wood 35 Removing of old u/s Arms of Chair writing S&F of new Arms as existingof Ist class hard wood 36 Removing of old u/s Front rail of Chair writing S&F of new front rail as existingof Ist class hard wood 37 Removing of old u/s Rear rail of Chair writing S&F of new Rear rail as existingof Ist class hard wood 38 Removing of old u/s Side rail of Chair writing S&F of new Side rail as existingof Ist class hard wood 39 Removing of old u/s Stiffnerof Chair writing S&F of new Stiffner as existingof Ist class hard wood 40 Removing of old u/s Back wooden of Chair writing S&F of new Back wooden rail as existingof Ist class hard wood 41 Removing of existing cane cleaning of cane holes and recanning with 2 mm wide new plastic cane for seat and 3.5 mm wide cane for borders of chairall as specified and shown on drg and as directed by Engr-in-charge. 42 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces. 43 CHAIR EASY (FD-229/FD-17) : Removing the u/s front legs ,S&F new front leg as existingof Ist class hard wood. 44 Removing the u/s Rear legs of chair easy ,S&F new Rear leg as existingof Ist class hard wood. 45 Removing the u/s Arms of chair easy ,S&F new Arms leg as existingof Ist class hard wood. 46 Removing the u/s Front rail of chair easy ,S&F new Front rail as existingof Ist class hard wood. 47 Removing the u/s Rear rail of chair easy ,S&F new Rear rail as existingof Ist class hard wood. 48 Removing the u/s Side rail of chair easy ,S&F new Side rail as existingof Ist class hard wood. 49 Removing the u/s Top/Bottom rail back frame of chair easy ,S&F new Top/Bottom rail back frame as existingof Ist class hard wood. 50 Removing the u/s Side rail back frame of chair easy ,S&F new Side rail back frame as existingof Ist class hard wood. 51 Removing of existing cane cleaning of cane holes and recanning with 2 mm wide new plastic cane for seat 3.5 mm wide cane for borders of chairall as specified and shown on drg and as directed by Engr-in-charge. (For chair Seat 0.51x0.45=0.2295 Sqm)(Back 0.43x0.34=0.1462 Sqm)Total 0.3757 Sqm 52 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces. 53 PEG TABLE (FD-277,FD-384): Removing the u/s leg of peg table,S&F newleg as existingof Ist class hard wood. 54 Removing the u/s long rail of peg table ,S&F new long railas as existingof Ist class hard wood. 55 Removing the u/s Short rail of peg table ,S&F new Short rail as existingof Ist class hard wood. 56 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces. 57 TEAPOY (FD-382, FD-278, FD-232) :Removing the u/s leg of Tepoy ,S&F newleg as existingof Ist class hard wood 58 Removing the u/s Stiffner of Tepoy ,S&F new Stiffner as existingof Ist class hard wood 59 Removing the u/s long rail of Tepoy ,S&F new long rail as existingof Ist class hard wood 60 Removing the u/s Short rail of Tepoy ,S&F new Short rail as existingof Ist class hard wood 61 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces. 62 SIDE BOARD/Bin Linon Multipurpose (FD-371/241) : Removing of u/s back , S&F new back of side board with 6mm thickBWR grade commercialply wood as existing and as per drg. 63 Removingthe existing u/s shutter,S&F new shutter as existing made out of 18/19mm thick prelaminated particle board one sidedecorative teak shade and balancing white shade to the other side. The shutter shall be fixed with 4mm thick TWedging all roundas per drg andfixed withaluminium anodised knob with ball spring catch. 64 Removing the u/s leg ,S&F newleg as existingof Ist class hard wood 65 Removing of u/s drawers, S&F new drawers made outof 12mm commercialplywood and fixed withaluminium anodised knoball as per existingand shown on drg. 66 Removing of U/S shelves from side board and S&F new shelves as per existing shape & size made out of18mm thick particle board one side teak faced. 67 Removing of U/S sideof side board and S&F new side made out of 18 mm thick prelaminated particle board as per existing shape & size 68 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces including inside of shutter 69 TABLE WRITING (FD-275/249) :Removing unsv legs and S&F legs as existingof Ist class hard wood 70 Removing unsv bottom stiffner S&F new stiffner of bottom as existingof Ist class hard wood. 71 Removing unsv drawer andS&F new drawer of table writing as existing andfixed with aluminium anodised knob. Rest all as per existing and as specified in drg. 72 Removing of U/S back ply from table writing and S&F new back ply of 6mm thick commercial plywood as per existing shape & size 73 Removing unsv bottom of box and S&F newbotom of table writing with 18mm prelaminated particle board as per existing shape & size and as specified in drg. 74 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces including inside of shutter 75 TABLE DRESSING LADIES (FD-378,FD-251) :Removing unsv back ply of mirror and S&F new 6mm commercial plywood to back of mirror as perexisting shapeand sizeas per drg 76 Removing unsv wooden memberand S&F new TW member for holding mirror alongwith mirror frame alround as existing. 77 Removing unsv top of box and S&F new top made out of 19mm thickPrelaminated particle board one side teak shade to the top of table dressing ladies all as per drg with 4mm thick TW edging. 78 Removing unsv alluminiumchannel and S&F new 12x22mm Aluminiumchannel for sliding glass all as per drg 79 Removing unsv legand S&F newleg as existingof Ist class hard wood 80 Removing unsvmirror and S&F new looking mirror of 5mm thickall as per drg and as existing 81 Removing unsv knoband S&F new aluminium anodised knob to drawer 82 Removing unsv drawerand S&F new drawer all as perexisting size made out of 12mm thick commercialplywood. 83 Removing unsv Cushion with cover for Stool dressing of dressing ladies and S&F new Cushion with cover all as perexisting size . 84 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces 85 TABLE DRESSING GENTS WITH MIRROR (FD-230/379) :Removing unsv back ply of mirror and S&F new 6mm thickply wood to back of mirror as per existing shape & size 86 Removing unsv wooden memberand S&F new TW member for holding of mirror alongwith mirror frame as per Drg 87 Removing unsvmirror and S&F new looking mirror of 5mm thickas per existingshape & size 88 Removing unsv knobsand S&F newaluminiumanodised knob to drawer 89 Removing unsv drawerand S&F new drawer all as perexisting size made out of 12mm thick commercialplywood. 90 Removing unsv Side to side board for dressing of Dressing Gents and S&F new Side to side board 18mm Prelaminated particle board all as perexisting size . 91 Removing unsv Glass shelf of dressing Gents and S&F new Glass shelf all as perexisting size . 92 Removing unsv catcher for Looking Mirror of dressing ladies and S&F new catcher all as perexisting size . 93 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces 94 TABLE DINING 6 PERS (FD-273, FD-30 ): Removing old unsv existing short rail and S&F new short rail of 1st class seasoned hard wood complete all as specified and shown on drawing. 95 Removing old unsv existing legs and S&F new legs of 1st class seasoned hard wood complete all as specified and shown on drawing. 96 Removing old unsv existing stiffener and S&F newstiffener of 1st class seasoned hard wood, fixed with dove tail jointcomplete all as specified and shown on drawing. 97 Removing old unsv existing corner bracket and S&F corner bracket of 1st class seasoned hard wood, made to shape at top of leg & frame fixed with screwscomplete all as specified and shown on drawing. 98 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces 99 TABLE DINING 1200 X900X760MM ( FD/MAP-II/03) : Removing old unsv existing long rail and S&F new long rail of 1st class seasoned hard wood complete all as specified and shown on drawing. 100 Removing old unsv existing short rail and S&F new short rail of 1st class seasoned hard wood complete all as specified and shown on drawing. 101 Removing old unsv existing legs and S&F new legs of 1st class seasoned hard wood complete all as specified and shown on drawing. 102 Removing old unsv existing stiffener and S&F newstiffener of 1st class seasoned hard wood, fixed with dove tail jointcomplete all as specified and shown on drawing. 103 Removing old unsv existing corner bracket and S&F corner bracket of 1st class seasoned hard wood, made to shape at top of leg & frame fixed with screwscomplete all as specified and shown on drawing. 104 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces 105 TABLE DINING 8PERS (FD-273/30) : Removing the unsv legs and S&F newlegs as existingof Ist class hard wood 106 Removing the existing u/s top railandS&F new rail as existingof Ist class hard wood 107 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces 108 BED HARD PLY WOOD TOP (FD-246/ 247) :Removing unsv plywood and beadingof headboard and S&F new teak veneered decorativeplywood 4mm thick to both sides of thehead boardincluding fixing6mm thick teak wood beading all round and as exising and as specified in drg . 109 Removing of unsv long rail & S&F new long rail made out of well seasoned teak wood as per existing shape & size 110 Removing ofunsv support short rail and S&F new short suport rail made out of TW as existing and as per drg. 111 Removing of unsv legs and S&F new leg made out of well seasoned teak wood as per existing shape & size and as shown on drg. 112 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces 113 SOFA SET1/4/ 5 SEATER (FD-281/ 373) : S&F 40 density 530x560x100mm cool foam cushion covered with cloth tapestry superior quality , colour, pattern and quality as approvedby GE/Engr-in-Charge. Make of cushion - SAMRAT/ Sleepwell /Kurlon.Each cushion cover shall be provided with one side openable zip. 114 S&F cushion cover only of size 530x560x100mm cloth tapestry superior quality , colour, pattern and quality as approvedby GE/Engr-in-Charge. Each cushion cover shall be provided with one side openable zip. 115 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces to sofa set 5 seater . 116 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces to sofa set Singal seater 117 Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat offrench polish to obtain a glossy finish on all the exposed surfaces to sofa set 4 seater 118 CHARPOY GI PIPE AND/IP HARD TOP (FD-220 ) :Removing of old unservicable existing elbows and S & F newGI elbowsThree way32mm dia ISI Markall as specified & directed 119 Removing of old unserviceable broken checknuts and S & F new GI check nuts for 32mm GI pipes ISI Marked all as specified & directed 120 Removing of existing unseviceable long rails from Charpoy GI pipe and S & F new long rails made out of GI pipe 32mm bore medium grade as per existing shape & size complete as specified & directed . 121 Removing exsting damaged short rails andfixing short rails to charpoy afterconversion from retrieved oldlong railsduly threaded at both endsand fixing the same as per exsting shape & size complete all as directed . 122 Removing exsting damaged legs andfixing legsafterconversion from retrieved old shortrailsduly threaded at one end and another side welding with 3mm thick MS sheet base and mild steel brackets of required size, shapefor fixingMNF set all as shown on drawing and as directed . 123 M & L for welding to broken/ cracked joints of charpoy GI pipe 32 mm dia (i.e) short rail, long rail, legs etc) by gas welding as per existing design rest all as specified and directed by Engineer-in-Charge. 124 Chair Varandah (FD-19(M), FD-256/ 359, FD- MAP -II/06) : M & L for repair / fixing of broken parts of chair varandah by welding (Gas Welding)as existing with 20mm dia MS Conduite pipe where ever requiredas directed. 125 M & L for preparation of surfaces and painting of chair varandah with two coat of synthetic enamelpaint white as specified and directed. 126 Removing of old exsting cane and recanning of chair varandah with new 4mm width 0.60mm thick cream colour plastic cane of approved qualityas specified in drg and as directed. 127 Removing of old unserviceable PVC seat and back from chair varandah and S&F new PVC seat and back 4mm thick weight not less than 1.85 Kgs for both seat and back having 4 x 10mm thick ribs moulded complete all as specified and as directed by Engineer-in-ChargeMake: Amko/Cello/Harmony 128 Supply and Fix new hard rubber shoessuperior quality (as approved) of required size to chair varandahas directed. 129 REPAIRS TO CHAIR CB STEEL WITH ARMS (FD-75(M)) : Removing of old unserviceable back frame of chair CB steel witharms and supply and fix new back frame made out of seasoned teakwood duly canned as per trade pattern.The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Noseach on either side of back duly welded and also making holes to back frame centre to centre by drilling machine for fixing back frame with steel pipes by required size screwsfor extra support as directed. 130 Removing of old unserviceable seatframe of chair CB steel witharms and supply and fix new seatframe made out of seasoned teakwood duly canned as per trade pattern.The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Noseach on either side of seatduly welded and also making holes to seatframe centre to centre by drilling machine for fixing seatframewith steel pipes by required size screwsfor extra support as directed. 131 Removing of old unserviceable hand rest and supply and fix new hand rest made out of well seasoned teakwoodwith required size screws. The hand rest shall befrench polished with black colour all as specified, directed and as shown on drawing. 132 M & L for preparation of surfaces and painting of chair CB Steel With Arms two coat of synthetic enamelpaint Olive Green. All as specified and directed. 133 ALMIRAH LARGE STEEL WITH SHELVES (FD-67 (M) /1031) : Removingunsvlegs of almirah and S&F newlegs made out of 1mm thick MS sheetas existing bywelding / revitting as per drg and as directed. 134 Removing of unsvshelves from almirah Large steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing 135 Removing of UNSV 3 way locking device. S&F completenewlocking device of same shape & size as existing andas per drg. 136 Removing of UNSVhandle from almirah large steel. S&Fnew CP handle 150mm long asapproved and directed. 137 Removing of old UNSV locks. S&F new brass lock 6 leversto almirah asapproved . 138 M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externallyby spray painting complete all as specified and as directed by Engr-in-Charge 139 ALMIRAH MEDIUMSTEEL WITH SHELVES (FD-67 (M) /1032) :Removingunsvlegs of almirah and S&F newlegs made out of 1mm thick MS sheetas existing bywelding / revitting as per drg and as directed. 140 Removing of unsvshelves from almirah medium steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing 141 Removing of UNSV 3 way locking device. S&F completenewlocking device of same shape & size as existing andas per drg. 142 Removing of UNSVhandle from almirah med steel. S&Fnew CPhandle 150mm long of approved make. 143 Removing of old UNSV locks. S&F new brass lock 6 leversto almirahasapproved . 144 M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applyingsynthetic enamel paint of required colour internally and externallyby spray painting complete all as specified and as directed by Engr-in-Charge 145 TABLE OFFICE OFFICER (FD-84(M)/ FD-1003) : Repairingframe oftablewithnew 25mm square MS tube of 1.6 mm thickby arc welding where ever required as directedby Engr-in-Charge 146 Removing of UNSV locks from table office Officer steel and S&F of new brass locks of 6 lever with duplicate key of approved quality as approved by GE/Engr-in-Charge. 147 Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all asspecified and directed by Engineer-in-charge 148 TABLE OFFICE CLERK STEEL (FD-84(M) / 1004) :Removing of old UNSV drawers from table office clerk steel and S&Fnew drawers made of 1.00mm thick sheet of same shape & size as existing. 149 Repairingframe oftablewithnew 25mm square MS tube of 1.6 mm thickby arc welding where ever required as directedby Engr-in-Charge 150 Removing of UNSV locks from table office clerk steel and S&F of new brass locks of 6 lever with duplicate key of approved quality as approved by GE/Engr-in-Charge. 151 Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all asspecified and directed by Engineer-in-charge 152 TABLE 3 X 2 WITH DRAWER STEEL (FD-1008) : Removing of old UNSV drawers from table 3 x 2steel and S&F of new drawers made of 1.00mm thick sheet of same shape & size as existing. 153 Repairingframe oftablewithnew 25mm square MS tube of 1.6 mm thickby arc welding where ever required as directedby Engr-in-Charge 154 Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified. 155 TABLE 3 X 2 WITH OUTDRAWER STEEL (FD-1007) : Repairingframe oftablewithnew 25mm square MS tube of 1.6 mm thickby arc welding where ever required as directedby Engr-in-Charge 156 Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified. 157 TABLE 3 X 3 STEEL (FD-1009) :Repairingframe oftablewithnew 25mm square MS tube of 1.6 mm thickby arc welding where ever required as directedby Engr-in-Charge 158 Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified. 159 LOCKER BED SIDE STEEL (FD-1029) :Removingunsvlegs of locker and S&F newlegs made out of 1mm thick MS sheetas existing bywelding / revitting as per drg and as directed. 160 Removing of unsvshelves from locker bed side steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing 161 Removing of UNSV hasp and staple of locker and S&F new hasp and staple of same shape & size as existing andas per drg. 162 Removing of UNSVhandle from locker bed side steel. S&Fnew steel handle 100mm long ofapproved make. 163 Removing of old UNSV hanging rodS&F new hanging rodCP of 20mm dia to locker approved . 164 M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externallyby spray painting complete all as specified and as directed by Engr-in-Charge 165 CHAIR EXECUTIVE REVOLVING STEEL (TP) :Removing old unsv seat of chair executive and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existingand as directed 166 Removing old unsv backof chair executive and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existingand as directed 167 Taking out old unsv castors wheel fromexecutive chair and S & F new twin wheel castors as per existing size and shape complete all as specified and as directed by Engr-in-Charge 168 Removing unsv gas lift and S&F newgas lift of 100mm stroke length and gas pressure of 300n force as existing. 169 CHAIR WRITING MAP (FD/E6/MAP-12)Taking out old unsv cantilever type MS framefromchair and S & F new cantilever type ms tubular frame made out of 25mm x 10mm secas per existing size and shape complete all as specified and as directed by Engr-in-Charge 170 Removing old unsv seat of chair steeland S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existingand as directed 171 Removing old unsv backof chair steel and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existingand as directed 172 Removing unsv armrestand S&F newone piece armrest made of black integral skin polyurethane with MS insert to the chairas existing with appropriate size bolt and nuts as specified and as directed. 173 CHAIR COMPUTER(FD/E6/ MAP/1) :Removing old unsv seat of chair computer and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existingand as directed 174 Removing old unsv backof chair computer and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existingand as directed 175 Taking out old unsv castors wheel from chair computerand S & F new twin wheel castors as per existing size and shape complete all as specified and as directed by Engr-in-Charge 176 Removing unsv gas lift and S&F newgas lift of 100mm stroke length and gas pressure of 300n force as existing. 177 BED HARD STEEL : FD/E6/MAP/08(R) Dismantling unsv stiffener and S&F new stiffener, made to shape, out of25mm square tube having wall thickness1.6mm by gas welding and one coat of primer complete all as specifed and shown on drg complete all as specified and shown on drg. 178 Removing old UNSV head rest and S&F of new head rest made to shape, out of38 mm square tube outer frame and section tube 18mm square having wall thickness1.6mm with gas welding and one coat of primer complete all as specifed and shown on drg complete all as specified and shown on drg. 179 Removing old UNSV foot rest and S&F of new foot rest made to shape, out of38 mm square tube outer frame and section tube 18mm square having wall thickness1.6mm welded with gas welding and one coat of primer complete all as specifed and shown on drg complete all as specified and shown on drg. 180 Removingold UNSV shoe and S&F new PVCrubber shoe of size 38mm at bottom of the leg complete all as specified and shown on drg. 181 Gas weldingof broken spot of 25mm dia pipecomplete all as specified and directed . 182 M&L for denting & painting of steel surfaces, exposed to view when placed in position and applying two coats of synthetic enamel black paint after preparation of old surfaces complete all as specified and shown drg . 183 COMPUTER TABLE (FD/E6/MAP/03) : Removing of old UNSV drawers of computer table and S&F of new drawers made of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the drawer of same shape & size as existing. 184 Removing of old UNSV key board of computer table and S&F of new key board made of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the drawer of same shape & size as existing. 185 Material & labour for painting to the frame of computer table with one coat of synthetic enamel paint olive black paint all as per specified. 186 PAINTING OF STEEL FURNITURE: M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying two coats of synthetic enamel paint for Side rack steel 3 spaces of required colour internally and externallyby spraypainting complete all as specifiedand as directed. 187 All as per Srl item No. 186 here-in-before but for Trestle store room steel 188 All as per Srl item No. 186 here-in-before but for Rack steel 1830x760x1905mm 189 All as per Srl item No. 186 here-in-before but for Rack Shoes Steel 190 All as per Srl item No. 186 here-in-before but for Stool Steel 305x305x760mm , 510mm & 610 mm 191 All as per Srl item No. 186 here-in-before but for Rack 6 tier steel 192 All as per Srl item No. 186 here-in-before but for Rack Pigeon hole steel 193 BOOK CASE STEEL (GLAGED) FD-1028, FD-90 Re-setting of existing dislocated shelvesby providingappropriate size clamps, nut and bolts of required numbers complete all as specifed and shown on drg. 194 S&F in replacementbrass lock, six/seven levers complete all as specified and shown on drg. 195 S&F in replacement powder coated mild steel handle 100 mm long for shutter complete all as specified and directed . 196 Dismantling unsv/broken glass for shutter and S&F new glass of 5mm thick glass for shutter fixed in MS frame, nut and bolts of apropriate size & required numbers complete all as specifed and shown on drg. 197 Preparation of existing painted steel surfaces (inside and outside) by carrying out denting, scraping old paint with sand paper, filling putty (where required) and applying one coat of synthetic enemel (olive green) paintwith spray gun complete all as specified and directed .
