Tender For Provision Of Pol Stores Near Mt Section At Af Station Sonegaon, Nagpur.; 1 Excavating over areas, n. exc. 1.5 m deep and getting out soft/loose soil (Black cotton soil) complete all as specified and directed. 2 Excavating over areas, exc 1.5 m deep and getting out soft/loose soil complete all as specified and directed. 3 Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed at a level n exc. 1.5 m above the starting pointand depositing where directed by EIC complete all as specified and directed. 4 M & L for Plain cement concrete in foundation filling type D-2 1:4:8 (40mm graded aggregate) and mass concrete complete all as specified and directed by Engr-in-Charge. 5 Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by Engr-in-Charge. 6 Formwork to sides of pillars, posts, struts, piers, columns and stanchions compete all as specified and directed by Engr-in-Charge. 7 M & L for RCC M-25 (using 20mm graded aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge. 8 M & L for RCC M-25 (using 20mm graded aggregate) Columns, pillars, piers, posts and struts concrete complete all as specified and directed by Engr-in-Charge. 9 M & L for providing RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. 10 M & L for providing RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. 11 Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. of rough finished surface also splays between floors and beams, etc complete all as specified and directed. 12 M & L 150mm thick cement concrete type C-2,1:3:6 (40mm graded aggregate) as in sub base with proper slope maintained to self-drainage complete all as specified and directed by Engr-in-Charge. 13 M & L for Hardcore of gauge not exceeding 63mm,deposited, spread and levelled in layer not exceeding 30cm thick, watered and rammed to true surface complete all as specified and directed. 14 M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed by Engr-in-Charge. 15 M & L for Brickwork with subclass ‘B’ bricks modular brick, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed. 16 M & L for 15mm thick rendering in CM 1:4 on fair faces of brick work using water proofing compound as per manufacture instruction complete all as specified and directed.Note: -WPC shall be measured separately. 17 M & L for 15 mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth complete all as specified and directed. 18 S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering, fixed with 12 mm dia bolt with 2 number washer instead of self-tapping screws complete all as specified and directed.Note: - bolt and washer shall be measured and paid separately. 19 S & F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with 12 mm dia bolt with 2 number washer instead of self-tapping screws complete all as specified and directed.Note: - Bolt and washer shall be measured and paid separately. 20 S & F 2 mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with 12 mm dia bolt with 2 number washer instead of self-tapping screws in roof, wall etc complete all as specified and directed by Engr-in-charge.Note: - Bolt and washer shall be measured and paid separately. 21 M & L for PCC (M-25) Design mix using 20mm graded stone aggregate for Ramp complete all as specified and directed. 22 S & F MS Rolled sections as in main and cross columns and beams, rafters; purlins; fixedwith angle cleats or other connecting platesFe- 410 (Gde E-250 Quality A) complete all as specified and directed by Engr-in-Charge. 23 S & F mild steel screw bolt,11 to 15mm dia machine made with hexagonal head at one and screwed the other or screwed bolts each screwed and to be filled with washer and one hexagonal or square nut exc 05cm and n exc10cm long complete all as specified and directed by Engr-in-Charge. 24 M & L for preparing the newly surface of any description not otherwise described over 10 cm width or girth on steel surface and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified and directed upto any height and in any shade and colour complete all as specified and directed by Engr-in-Charge. 25 M & L for 75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection & paving finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. 26 Use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete complete all as specified and directed. 27 M & L for providing RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in chajjas complete all as specified and directed. 28 S & F for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to IS (Fe 415 D) complete all as specified and directed. 29 Ditto - All as per Item No. 29.00 above but for 5mm dia and over up to and including 10mm dia in stirrups complete all as specified and directed. 30 S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-Charge. 31 Ditto – All as per Item No. 31.00 above but without glazing bars complete all as specified and directed. 32 S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed by Engr-in-Charge. 33 S & F 3mm thick sheet glass ordinary quality and fixing with Oil putty complete all as specified and directed by Engr-in-Charge. 34 S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 35 M & L for preparation newly prepared wood surface not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paints over a coat pink primer complete all as specified and directed. 36 S & F frame work such as grills, grating etc with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, barred iron doors, ladders etc and similar works conforming to Fe-290 Gd E-165 complete all as specified and directed. 37 Supply only liquid water proofing compound. 38 M & L for Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of priming plastered surfaces with alkali resistant priming paint complete all as specified and directed. 39 M & L for applying three coats of white wash on newly plastered surfaces on wall after necessary preparation of the surface, complete all as specified and directed. 40 S & F Steel rolling shutter of lath thickness 1.25 mm, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete:gear operated type with bevel gear box and crank handle with 2nos each Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed by Engr-in-Charge. 41 M & L for 20mm Screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and as directed. 42 M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. 43 M & L for concealed type wiring for explosive storage accommodation with PVC insulated 1.5 Sqmm multi stranded copper conductor cable, FRLS, 1100 Volts grade drawn in and including surface mounted ERW stove enamelled black steel conduit not less than 20mm dia with and including flame proof bends and elbows, couplers, bell mouth reducer except junction box all as per relevant IS fixed with solid baked distance saddles, and elevated MS spacer plate fixed with nettle fold GI screws along with 1.0 Sqmm PVC insulated solid strand copper conductor FRLS 1100 Volts grade as ECC connected to common earth dolly for the following points complete all as specified and as directed. 44 One light point controlled by one rotory switch. 45 One exhaust fan point controlled by one rotory switch. 46 S & F flame proof ON/OFF rotary switch of cast Aluminium alloy SP 10/16 Amp 240 Volts in LM-6 complete all as specified and as directed. 47 S & F flame proof /weather proof light fittings suitable for 1 x 18/20 Watt LED tube light fittings with built in control rear box as per relevant IS complete with accessories and 1 No of 18/20 Watt LED tube rod complete all as specified and as directed. 48 S & F flame proof /weather proof exhaust fan size 12” as per relevant IS complete suitable for single phase 0.25 HP, 1440 RPM, 1120 CFM, 240 Volts complete all as specified and as directed. 49 S & F flame proof DB, 4 Way with MCB DP 16/25 Amps capacity construction with cable entries at bottom/Top for incoming and 2 Nos MCB 6/10 Amp as outgoing circuit complete all as specified and as directed. 50 Earthing with galvanised iron earth plate electrode 600 x 600 mm & 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal GL) with top of earth plate not less than 1.5 metre below GL connected to GI earth lead wire 4 mm dia connected to earth plate electrode by means of GI nuts, bolts & washers earth wire protected with & including 15 mm dia medium grade ISI marked GI pipe not less than 7.5 metre long all as shown in electrical plate No. 3 MES Schedule Part 1, with & including ; PCC 1:3:6 type B1 reinforced with welded steel wire fabric not less than 4 Kg per Sq M, watering arrangements with 20 mm GI medium grade pipe ISI marked , GI funnel with GI mesh, filling with mixture of common salt & charcoal, necessary excavation and earth work in any type of soil, including test point, testing & commissioning, complete all as specified and as directed.Note: - GI earth wire with GI pipe protection beyond 7.5 metre measured and paid separately.
