Tender For Addition/Alteration Cum Special Repairs To Compound Wall Of Convoy Ground At Rear Side Of 1806 Pioneer Unit Under Ge (West) Lucknow.; 1 Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. 2 M&L Old size brick work using fly ash bricks conforming to IS-12894:2002, non Modular,class designation 7.5, straight or curved on plan exc 6m mean radius, built in Cm (1:4)complete all as specified and directed. 3 Excavation in trenches n.exc 1.5 m in depth for foundationn.exc. 10 sqm on plan and n.exc1.5 mtr in depth and getting out completein soft/loose soilcomplete all as specified and directed. 4 M & L for cement concrete type D2 1:4:8 (40mm gradedaggregates) in foundation filling and mass concretecomplete all as specified and directed. 5 S & F for MSTMT bars 10 mm dia and over , cut to length , bent to shape required incl cranking bending spirally for hooping for coloumn hooking ends and binding with and incl mild steel wire annealed not less than 0.9mm dia or securing with clipscomplete all as specified and directed. 6 S & F for MSTMT bars 5mm to 10 mm dia and over , cut to length , bent to shape required incl cranking bending spirally for hooping for coloumn hooking ends and binding with and incl mild steel wire annealed not less than 0.9mm dia or securing with clipscomplete all as specified and directed. 7 M & L for form works rough finished surfaces of concrete side of concrete foundation , footing , bases of coloumns raft and raft beams sides and sofits if any of foundation and plinth beams and similar work flat , vertical or to battercomplete all as specified and directed. 8 M&L for form work to sides of pillar, posts, struts, columns etccomplete all as specified and directed. 9 M&L for form work to sides and soffits of beams lintel band and the likecomplete all as specified and directed. 10 M & L for Reinforced cement concreteM-25 design mix(using 20 mm graded stone agg) as infoundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete in foundation, footingscomplete all as specified and directed.. 11 M & L for Reinforced cement concreteM-25 design mix(using 20 mm graded stone agg) in columns, pillars, piers, posts and struts etccomplete all as specified and directed. 12 M & L for Reinforced cement concreteM-25 design mix(using 20 mm graded stone agg) in beam cantilevers, bressummers, lintels over 1.5 m span etccomplete all as specified and directed. 13 M & L for 15 mm thick rendering cement plastering on fair faces of brick work or concrete surfaces 1:4 mixed with WPC (WPC will be measured separately)and finished even and smooth (without using extra cement) 14 M & L preparation of new plaster surface and applying two coats of cement base paint on newly plasteredwall surfaces complete all as specified and directed. 15 Returning, filling in including spreading leveling, watering and well ramming in layers not exceeding 25cm in soft/loose soil as requiredcomplete all as specified and directed. 16 Removing excavated materials soiln.exc. 50mtr and depositing where directed at a level n.exc. 1.5 mtr above the starting pointcomplete all as specified and directed. 17 M & L for angle posts and struts in fencing including cutting tops to shape as directed drilling holes notching for hole including necessary drilling bilting or rivetting complete or forged into spikes framed guards bars conforming to Fe-290 Gde E-165 complete all as specified and directed. 18 M &L for preparation of steel surfaces of any description over 10cm in width or girth not otherwirse described and two coat of synthetic enamel paint over one coat of red oxidecomplete all as specified and directed. 19 S & F for galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or typing at crossings with and provision of galvanised mild steel wire stapes or steel pins, etc as directed (each line wire to be measured.) 20 S&F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete Fe-290-Gde-E-165complete all as specified and directed. 21 S & FGalvanised. 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barb at 75mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins, etc including dismantling/taking out barbed wire in fencing complete all as specified and directed.(each line of wire to be measured). 22 S & F mild steel screw bolts (machine made ) with hexagonal or square heads at one end, 10mm dia, not exc 10 cm long, bolt with waher and nutsdia of neck 5 to 10 mmcomplete all as specified and directed. 23 Supplyand fixing of 3mm dia GI wirechain link fencing with 75x75mm mesh size and fixed to anytype of strandard rails straining bolts etc including provision ofbinding wire including dismantling fencing wiremesh any type complete all as specified and directed. 24 S&F Concertina coil fencing with punched tape coil 450mm dia (at stretched position), made out of hot dipped, galvanised steel wire coated with CLR anti corrosive paint, making diamond shape barbs with 18 SWG sheet, spring core 2.5mm thick wire with tape 0.52mm thick and weight of each coil should not be less than 7.50 Kg, each coil should have 50 rounds and should covers 6 RM length, fixed over and including 6 lines of horizontal RBT (reinforced barbed tape) wire or razor wire at points wherever coil touches the bottom of wire with the help of hog rings (14 SWG) and in between Y shaped angle iron post complete all as specified and directed.NOTE:(i) Hogging shall be fixed at a interval of 600mm centre to centre, wherever it touches with the razor wire.(ii)Overlapping of concertina coil and razor wire shall be 300mm.(iii)Y shaped angle iron post shall be measured and paid separately under respective items. 25 S&F Reinforced concrete pipes 450 mm dia, class NP3, laid on 150 mm thick bed of PCC 1:4:8 with excavation upto 1.65 m depth in any type of soil, Incl manhole/drop man hole of srandard size made of brick masonry/RCC/Pre cast RCC with SFRC Ventilating cover and frame includes all items and activities to execute and make sewer line functional complete with collars complete all as specified and directed. 26 Supply only Integral water proofing compound confirming to IS-2645-2003of approved makecomplete all as specified and directed.
