Tender For Repair To Joinery Plumbing Flooring And Other Misc Br Repairs In Otm And Md Accn Of Prtc Ta Bn Under Ge North Bangalore; 1 Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm and Re-fixing in same opening after rectify the defect complete all as specified and directed 2 Resecuring or easing & adjusting without taking down shutters of any description exc 1 sqm but n.exc 2 sqm each complete all as specified and directed 3 Taking down chowkat (without taking of shutter from the frame) area not exc 1.5 sqm each including making good the disturbed surface in PCC 1:2:4 type B0 or CM 1:3 all as specified and directed 4 All as per Item No 1 above, but area exc 1.50 sqm and not exc 4.00 sqm each 5 Taking down shutters of any description area exc 1 Sqm but not exc 2 Sqm each all as specified and as directed 6 S&F Solid PVC door frame (Single rebated) of size 60 mm x 30 mm made out of solid foam with homogenious fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and directed 7 M & L for Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing with wood free EPS. 8 S&F 2nd class hard wood plain, solid, straight chowkats and frames, clean sawn, frame rebeated on the solid , rounded or chamfered, put tegether with glue pinned at joints etc complete all as specified and as directed 9 S&F Flush door shutters 35mm thick, factory made as per IS:2202 (Part-I 1999) solid core construction, with block board core with decorative face veneer both faces with lipping/frame to match as per drawing fixed to chowkhats all as speified and directed 10 S&F 2nd class hard wood 35 mm thick made glazed and skeleton shuttersopen rebated and prepared to receive glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified and as directed Note: Supply & fixing of 4 mm thick sheet glass or wire mesh be measured and paid separately. 11 S & F Plain framed, panelled shutter (two panel) of 35mm thick with lock rail and panel of 9mm BWP commercial ply or 12mm venereed particle board with commercial veneering on both faces. rail and style are of 2nd class hardwood & The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treateds fixed to chowkhat all as specified and as directed. 12 S&F for mild steel work as in hold fast made in flat ironall as specified conforming to Fe-290, Gde-E-165. 13 M & L for powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified ) 14 M & L Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Note: Supply & fixing of 4 mm thick sheet glass or wire mesh be measured and paid separately. 15 S&F Anodised aluminum powder coated (of any shade/colour as approved by GE ) ventilators with adjustable 4mm thick figured glass louvers, fixed in half portion, without sash bars, aluminum section weighing not less than 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, including stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.18mm including complete etcall as specified and directed by the Engineer-in-charge (Size of Ventilators = 500x850 mm) 16 M & L for powder coatedaluminium grill ( powder coated or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement all as specified and as direction of Engineer-in-charge. 17 M & L for plain cement concrete for filling of steel door frametype C0,1:3:6 using 12.50mm graded stone aggregate complete 18 Supply & fix Sheet glass 4mm thick ordinary quality and glazing with oil putty or in wooden /steel /aluminium /rubber beading in square not exceeding 0.5 Sqm in each pane and all as specified. 19 Supply & fix Sheet glass 4mm thick ordinary quality and glazing with oil or in wooden /steel /aluminium /rubber beadingputty in square exceeding 0.5 Sqm in each pane and all as specified. 20 Supply & fix stainless steel wire cloth 0.36mm nominaldia and average width of aperture 1.40mm and fixed with tinned tack or galvanized wire staple all as directed fixed. 21 Dismantling of structural steel work including doors,gates but excluding framed truss etcall as specified. 22 S&F MS framed work as in doors or gates of angle or other sections with gusset plates, rails braces, etc complete drilled for fixing of steel sheeting or other covering, doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails and guides) and hanging ; also fastening and fixing complete including painted with one shop coat of zinc chromate primer paint (including preparation of surface) at contractors workshop/factory before fabrication conforming to Fe-410-w Gde E-250 quality B complete all as specied and directed 23 S & F of 1.25 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required 24 M&L preparing new wooden surface of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed 25 M & L applying two coats of synthetic enamel paint over a coat of red oxide primeron steel surfaces over 10 cm width or girth including preparation of new steel surfaces 26 S & F Butt hinges stainless steel 100mm long and fixedto door frame and shutterduly welded / screwed complete all as specified and as directed 27 S & F Butt hinges medium weight, cold rolled mild steel 100mm long and fixedto door frame and shutterduly welded/screwed complete all as specified and as directed 28 S&F Aluminium anodised towerbolt 150mm long of extruded section etc complete all as specified and as directed 29 S&F Aluminium anodised towerbolt 200 mm long of extruded section etc complete all as specified and as directed 30 S&F125 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed 31 S&F150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed 32 S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed 33 S & F 140 mm floor door stopper of aluminium alloy powder coated, with hard down steel springall as specified and as directed. 34 S&F mild steel 300mm, ordinary rat tail rod pattern springs,including roller and roller plate complete 35 M & L4 mm thick figured glass, pin head type and glazing with oil putty/wooden or steel beading in squares n.exc 0.5 Sqm in each pane all as specified and as directed. incl Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips etc complete all as specified and as directed. 36 M&L for 3mm thick Sheet glass, ordinary quality and glazing withoil putty / wooden or steel beading in squares n.exc 0.5 sqm in each pane all as specified and as directed. incl Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips etc complete all as specified and as directed. 37 M&L for 5mm thick sheet glass, ordinary quality and glazing with screw in square exc 0.5 sq. m in each pane incl glazing clips/beading, rubber etc incl Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips etc complete all as specified and as directed. 38 S & F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.18 mm fixed with MS screw or nut bolts with or without wooden or steel beading in repairs all as specified and as directed. 39 S & F in repairs Aluminium anodised barrel towel bolts of extruded section of length 150 mmall as specified and as directed. 40 S & F in repairsAluminium anodised barrel towel bolts of extruded section of length 200 mm all as specified and as directed. 41 S & F in repairs Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections including taking down old sliding door bolt 300 mm all as specified and as directed. 42 S & F in repairs Extruded alloy handles fabricated type anodised of size 125 mmall as specified and as directed. 43 S & F in repairs Extruded alloy handles fabricated type anodised of size 150 mmall as specified and as directed. 44 S&F in repairs Butt hinges medium weight cold rolled mild steel of size of hinges 100mm 45 S & F in repairs 140 mm floor door stopper of aluminium alloy powder coated, with hard down steel springall as specified and as directed. 46 S&F in repair mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed. 47 S&F inrepairs door closer hydraulically regulated designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg of aluminium (extruded section)body in repairs complete all as specified and as directed. 48 S & F in repairs18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work,alround6mm th teakfillets fixed in kitchen Cabinet or cupboardsall as specified. 49 M&L for Plain fillets square, rectangular or triangular in section clean sawn , secured with nails or brads of second class hard wood fixed to cupboard shutter including taking down old fillets exc 6 & n exc 13 sqcm cross section area all as specified and directed. 50 S&F Continuous (piano) hinges 30mm width of flaps (when open) , mild steel, bright finish or electro galvanised 51 S&F 100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws 52 S&F Magntet door catcher made of stainless steel complete all as specified and directed 53 S & F 40 mm dia cupboard knobs fixed with nut, screw and washer of Brass,polished complete all as specified and as directed. 54 S & F in repairs Hasp and staple safety type of size 100 mm of aluminium anodizedall as specified and as directed. 55 S & F in repairs 40 mm dia cupboard knobs fixed with nut, screw and washer of Brass,polished complete all as specified and as directed. 56 S & F in repair Ball catcheswith 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed. 57 S&F in repairs stainless steel decorative curtain rod of 20 mm bore with wood finishes (weight not less 300 gms per running meter) incl fancy finale caps cap etc complete all as specified and as directed 58 S&F in repair Bracket for curtain rod of dia 20 mm dia made out of SS Flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long incl wooden base etc complete etc complete all as specified and as directed 59 Welding in repairs thickness of metal to be welded nexc 6mm complete all as specified and directed. 60 S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. 61 S&F solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing including dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. 62 Dismantling wrought iron or mild steel work of any description not otherwise provided for 63 M&L for MS rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410-w, Gde-E-250 quality A 64 S&F 4mm Non asbestos fibre cement building boards including anodised aluminium snap grid frame work of size of grid 605 x 605mm for false ceilingfixed or laid/ inserted to Aluminium framework with screws including taking down old celing of any description complete all as specified and directed. 65 S&FPre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of sheet of any type and any thickness complete all as specified and directed. 66 S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of sheet of any type and any thickness complete all as specified and directed. 67 Demolition of brick work or stone/boulders masonary built in cement mortar incl all quoins arches pillars etc but excl ashlar facing, dressed stones work and precast concrete articles. 68 ML for Pre-cast cement concrete block type B1 1:2:4 (20mm graded stone aggregate) masonry with solid blocks , exc. 10cm in width andsetting inin CM 1:6, complete all as specifid and as directed. 69 Taking down cement plaster of any description including racking out joints, hacking for key and disposal of debris to out side MD land all as specified and as directed. 70 M&L for Rendering 15mm thick in CM 1:6 on brick or concrete surfaces , finished even and smooth with out using extra cement. (Internal Surfaces) 71 M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 with WPC,finished plastered surface even and smooth without using extra cement (External Surfaces)Note :- WPC will be measured and paid separately 72 Supply only liquid water proofing compound 73 M&L for Rendering 5 mm thick in CM 1:3 on ceiling surfaces, finished even and smooth with out using extra cement. 74 Preparation of new plastered surfaces and applying three coats ofwhite wash on ceilings including in narrow widths/ bands etc complete all specified and as directed. 75 Preparation of newly plastered surfaces and applying twocoats of cement base paint over one coat of primeron walls including in narrow widths/ bands etc complete all specified and as directed. 76 Preparation of newly plastered surfaces and applying two coats of oil emulsion distemper overone coat ofprimer on walls including in narrow widths/ bands etc complete all specified and as directed. 77 M&L providing cement concrete type E2 1:5:10 (40mm graded stone aggregate) infoundations, filling and mass concrete for sunken floor including Demolition of cement concrete exc 15 cm thickness but above ground floors including removal of debris from MD Land complete all as specified and as directed. 78 Material and labour for water proofing to sunken portions of WCs, bathroom and kitchen etc by applying water based, cold applied, single component, elastomericin-situ seamless monolithic coating ready to use acrylic modified bituminous liquid membrance with the procedure in sequence all as specified and as directed.SURFACE PREPARATION (i) Removing all loose gravel, dirt, oil, grease and foreign matter by jet of dry air andcleaning the surface mechanically or by grinding to make it smooth before application. (ii) Repairing all cracks by cutting “V” groove and fill with PMC mortar prepared in theratio of Shalicrete : cement : sand (1:2:5) or equivalent. (iii) Providing 50 mm x 50 mm coving made out of PMCmortar as above.MATERIAL PREPARATION (i) Stir TarFelt® LM or equivalent by a slow speed mixture (approx. 400 rpm) fitted witha suitable mixing paddle to ensure a homogenous mix. (ii) After stirring, wait for the product to settle in order to let entrapped air escape. Condt/--79 79 Condt/--78WATERPROOFING APPLICATION(i) Slightly damp the surface. Avoid standing water / ponding.(ii) Prime the surface with a mixture of TarFelt® LM or equivalent and potable water inthe ratio of 50:50 and apply @400 grm / m2 of the mixture and allow it to touch dry.(iii) Apply first coat of TarFwlt® LM @ 0.70 kg / m2 by brush / roller / airless spray whilethe primed surface is tracky, For faster and smoother application, airless spray is preferred.(iv) Spread fiber glass net of 45 gsm with overlap of 50 mm in both directions when thesurface is till tackty.(v) Allow 1st coat to dry for 10-12 hrs.(vi) Apply second coat of TarFelt® LM @ 0.70 kg m2 by brush / roller / airless spray forfinal DFT of 1000 micron in two coats inclusive of fibre glass of 45 gsm (theoreticalcoverage depending on surface conditions).(vii) Sprinkle sand @ 200 grm / m2 over the final vertical coating when the surface is stilltackty to facilitate plastering.(viii) Ensure final curing time of 36 hrs before allowing / carrying out any further work.(ix) Conduct ponding test after 7 days of curing at ambient temperature. 80 M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite ,including cutting and polishing laid on 15 mm thick screed bed in CM 1:4 set and jointed including dismantling of old stone slabs laid bedded and pointed in any mortar complete all as specified 81 M & L for Providing edge moulding to 18-20mm thick granite stone any description of counters vanitiesetc. including machine polishing to edge to give high gloss finish etc. complete 82 S&F in repairs 15mm bore CP pillar taps, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered `Hot or `Cold with long screwd shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. 83 S&F 15mm stop valves/ angle valves cast copper alloy, screwed down, high pressure, fancy type, chromium plated screwed both ends for iron pipe or for unions and fixed in repairs. 84 S&F 15mm stop valves cast copper alloy, screwed down, high pressure, fancy type, chromium platedwith long shankandcup (concealed type) screwed both ends for iron pipe or for unions and fixed in repairs. 85 S&F bib tap 15mm, standard of CP fancy type, chromium plated any colour high pressure screwed for iron pipe and fixed in repair. 86 S&F two way bib cock with angle valve combination brass chromium plated, fixed in repairs. 87 S & F chromium plated long body bib tap 15mm dia with CP flange as fixed in repair all as specified and as directed. 88 S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position including taking down old complete in all respect as specified. 89 S&F wash basinBrass CP mixer for mixing hot & cold water screwed down for iron pipe 15 mm and fixed in repairs 90 S&F concussive push button tapsof cast copper alloy, for 15mm dia of pipe, screwed for iron pipe and fixed in repairs. 91 M&L in repairs 40mm dia, 800mm long corrugated waste pipe complete all as specified and as directed. 92 M&L in repairs 32mm dia, 800mm long corrugated waste pipe complete all as specified and as directed. 93 S&F in repair 15mm dia Bib tap PTMT fancy type any colour screwed, for iron pipe and fixed 94 S&F in repair 20mm dia Bib tap PTMT fancy type any colour screwed, for iron pipe and fixed 95 S&F in repair 15mm dia Pillar tap PTMT fancy type any colour screwed, for iron pipe and fixed 96 S&F in repair 15mm dia angle stop valve ofPTMT any colour pressed screwed, for iron pipe and fixed 97 S & F PVC sintex tank cover suitable for 500/1000 ltr tank complete as in repairs 98 S & F in repairs Towel rail stainless steel glossy finish complete all as specified and as directed. 99 S&F in repairs Soap dish chromium plated brass all as fixed in wall as per manufacturers instruction. 100 S & F in repairs 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified 101 S & F in repair PVC connection (Suitable for Cold Water Supply) 15 mm size with PTMT nuts of length 450 mm,all as specified and as directed. 102 S&F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. 103 M&L 32 mm dia waste fittings,brass,chromium plated for sinks,basins,etc with long screwed shanks and flynuts,flange end fixed in repair complete all as specified and as directed 104 M&L 75 mm dia waste fittings,brass,chromium plated for sinks etc with long screwed shanks and flynuts,flange end fixed in repair complete all as specified and as directed 105 Supply & laying 20 mm outer dia CPVC pipes SDR 11 ( Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings and specials including taking down 15 mm GI tubing and connections complete all as specified. 106 Supply & laying 25 mm outer dia CPVC pipes SDR 11 ( Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings and specials including taking down 20 mm GI tubing and connections complete all as specified. 107 S & F in repairs 20 gate valvescrewed both ends for iron pipe/CPVC Pipe and including taking down old gate valve/ball valve complete all as specified and as directed. 108 S & F in repairs 25 mm gate valvescrewed both ends for iron pipe/CPVC Pipe and including taking down old gate valve/ball valve complete all as specified and as directed. 109 M & L for 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in positionon roofs including 20 mm dia ball valve and fittings includingdismantling existing water storage tank, complete all as specified. 110 M & L for 1000 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in positionon roofs including 20 mm dia ball valve and fittings includingdismantling existing water storage tank, complete all as specified. 111 S & F in repairs 25mm bore dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 25mm-455gms) all as specified and as directed. 112 S&F in repairs 10 ltrs capacity PVC valveless syphonic action flushing cistern low level with inlet ball valve, flush pipe of polythelene of low or high density or PVC 32mm dia comlplete all as specified and directed. 113 S&F in repair plastic water closet seat cover for western & indo western pedestal pan closed pattern with flat bottom, and cover and mild steel chromimium plated or aluminised hinging device fixed complete all as specified and directed. 114 Demolition of cement concreteand paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed. 115 Dismantling of stone slabs and tiles laid dry or laid dry and pointed of any description or thickness in floors, aprons etc. 116 Dismantling of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc. 117 M & L cement concrete type B0 1:2:4 (12.5 mm graded stone aggregate) 25mm thick finished even as in levelling concrete for floor. 118 M & L providing 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in subbase / plinth protection. 119 M & L providing 100mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in subbase. 120 Dismantling of floor, hearth or wall tilling incl cement mortar bedding (but not backing) and removing rubbish off from premises. 121 M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying floor finishes all as specified and as directed. 122 M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying floor finishes all as specified and as directed. 123 M & L Glazed ceramic coloured tiles in vertical surfaces 350 x 250x 7 mm/ 450 x 350 x 7 mm/ 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaceover & incl 10mm thick in screed CM 1:4onbrick work or concrete surfaces to receivewall tiles all as specified and as directed. 124 M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set ,jointed and pointed in neat cement slurry in floors.(with grey cement and pigments) over 20mm screed bed or bedding layer of mortor in CM 1:6 complete all as specified. 125 M&L for M-Sand filling under floors or in foundationincluding watering and consolidation complete all as specified and as directed. 126 M&L for Machine pressed precast concrete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as specified and as directed. 127 M&L for Kota Stone slab 18 - 20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. 128 M&L 40mm thick Plain Cement concrete type B-1,1:2:4 (20mm graded stone aggregate) as in flooring 129 S&F in repair Vitreous China wash basin, white, flat back, size550x400mm including 32 mm dia brass waste coupling ,chromium plated fancy type pillar taps, waste pipe, 600 mm long PVC connection & brackets including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing & supply and waste pipe. 130 S&F in repair Vitreous china wash down water closet pan ( pedestral Pattern) white, (Including flushing cistern and flush pipe), including connection to drain & or out going pipe ) and to flushing pipe, anti syphonage pipe, seat and cover for pedestral pan including PVC flushing cistern and 450 mm long PVC connection etc. 131 Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC SWR P trap 10 litr PVC flushing cistern,600 mm long PVC connections connecting to flush pipe and to anti syphonage pipe, etc. complete including making good to floor, fixed in repairs complete all as specified and directed. 132 S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe ) but including Concussive push button taps of cast copper alloy, screwed for iron pipe, PTMT waste coupling suitable for urinals, (Minimum weight 32mm-45gms urinal spreader and 450 mm long PVC connection and PVC urinal waste pipe complete all as specified and as directed. 133 S & F in repair 75 mm dia bore PVC (SWR) type B pipes single socketed in any length with rubber ring joints fixed to walls including necessary fittings all as specified and as directed. 134 S & F in repair 110 mm dia bore PVC (SWR) type B pipes single socketed in any length with rubber ring joints fixed to walls including necessary fittings all as specified and as directed. 135 S&F 75mm dia PVC (SWR) Bends with access door of any radious 136 As per item No. 135 above butfor 110mm dia 137 S&F 75mm dia PVC (SWR) junction single(single T) equal or unequal with access door 138 As per item No. 135 above butfor 110mm dia 139 S&F 110mm PVC (SWR) branch piece, double (single Y) equal or unequal 140 S&F 110mm PVC (SWR) branch piece, double (double Y) equal or unequal 141 S & F in repairs 32mm dia GI pipe (one side perforated) in spout of sunken floor all as spesified and directed 142 S & F in repair 75mm dia PVC(SWR) floor trap, plain with grating including jointing with slvent cement all as specified and as directed.
