Providing Basic Amenities To Tourist At Khadakwasla Dam Phase 02 Tal Halevi Dist Pune.-A Civil Work 1 212.42 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting, dewatering etc. complete. (Lift upto 1.5 metre) by Manual Means. 2 22.73 Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth /murum, ramming, watering including shoring and strutting, dewatering etc. complete (lift upto 1.5 metre) by Mechanical Means. (186) 3 268.62 Providing and laying Cast in situ/ Ready Mix cement concrete in Mix- 10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based Programmable Logic Controller with Superwisery Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand V.S.I. Grade). 4 12.55 Providing and laying in situ/ Ready Mix cement concrete Mix- 20 of trap/ granite/quartzite/ gneiss metal for Reinforced Cement Concrete work in foundations like raft, strip foundations, grillage and footings of Reinforced Cement Concrete columns and steel stanchions etc. including bailing out water, formwork, laying/ pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided, (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based Programmable Logic Controller with Superwisery Control and Data Acquisitionenabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Crushed sand V.S.I. Grade). 5 12.12 Providing uncoursed rubble masonary of trap stones in cement mortar 1:6 in foundations and plinth of inner walls/in plinth of external walls including bailing out water manually, striking joints on exposed faces and watering complete. (187) 6 2.43 Providing and laying cast in situ/ Ready Mix cement concrete Mix-20 of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based Programmable Logic Controller with Superwisery Control and Data Acquisitionenabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Crushed sand V.S.I. Grade). 7 2.25 Providing and fixing in position Thermo Mechanically Treated (TMT) FE -500 bar reinforcement of various diameters for Reinforced Cement Concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules, including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. 8 397.00 Providing earth work in embankment with approved materials obtained from other sources upto lead of 50 metre including all lifts, laying in layers of 20 centimetre to 30 centimetre thickness breaking clods, dressing to the required lines, curves, grades and section, watering and compaction with vibratory roller with VSat attachment to achieve not less than 97% of standard proctor density etc. complete (Material obtained from Other sources). (188) 9 1195.00 Painting letters upto 20 centimetre height complete, brushes, coir brushers dusting cleaning including cost of paint complete. 10 2621.23 Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 60 milimetre thickness of having a strength of 300 kilogram per square centimetre of approved quality and shape on a bed of crushed sand of 25 to 30 milimetre thick including skirting joints and cleaning etc. complete 11 1.39 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 centimetre to 20 centimetre thick including hand packing and compacting etc. complete. 12 5.28 Providing and fabricating structural steel work in rolled sections, fixed with connecting plates or angle cleats in main and cross beams, hip and jack rafters, purlins connecting to truss members and the like, as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/ bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. 13 801.00 Providing and casting in situ or precast tapering Reinforced Cement Concrete Mix-20 Barrier type Kerb without gutter (as per IRC:86-1983) embedded 125 milimetre below ground level over Mix-10 Plain Cement Concrete finished neatly with Cement Mortar 1:2, setting the same in Cement Mortar 1:2, including the required excavation in any strata and removing the excavated stuff anywhere in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant. 14 65.16 Providing and fixing mild steel grill railing 15 kilogram per square metre with teak wood hand rail of size 75 milimetre x 60 milimetre and sill of 75milimetre x 25 milimetre and newel posts for staircases, including fabricating, fixtures, erecting, painting the grill work with one coat of anticorrosive paint and two coats of oil painting with approved colours and polishing the sill, hand rail and the newel post with french polish. 15 97.32 Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950- 1050 mm effective cover width and nominal 25-30 mm deep ribs with subtle square fluting in the five pan at nominal 180- 250 mm center-to-center. The end rib shall be designed for anticapillary groove. and return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc- Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 kg/sqm) (190) 16 2.50 Filling in plinth and floors with approved excavated material 15 centimetre to 20 centimetre layers including watering and compacting etc. complete. Spec. No. : Bd.A. 11/Page No. 262 17 8.54 Providing second class Burnt Brick masonry with conventional Indian Standard type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding complete. 18 37.15 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 milimetre thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 milimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc. complete. 19 3.45 Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. 20 34.85 Providing internal cement plaster 12 milimetre thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. 21 2.74 Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted /bolted / welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. 22 72.00 Providing and applying two coats of exterior acraylic emulsion paint conforming to corresponding I.S.of approved manufacture and of approved colour to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary and watering the surface for two days etc. complete. 23 30.00 Providing and errecting chain link fencing 1.6 metre height with galvanised iron chain link of size 50 x 50 milimetre 8 guage thick and fixed 75 milimetre above Ground level on vertical Mild Steel Angle of 40x40x6 milimetre size including excavating pits for foundation and embeded in cement concrete block of 1:4:8 mix of size 450x450x670 milimetre at 1.75 metre center to center with iron bar 16 milimetre diameter as hold fast including welding link with angle frame at 30 cm. c/c nuts and bolts and horizontal Mild Steel Angles at top and bottom of 25x25x5 metre size and vertical Mild Steel flat 35 x 5 metre and 25 x 5 metre horizontal including cross support of 40x40x6 metre Angles both sides at every corner or bends embeded in concrete blocks of 1:4:8 of size 450x450x670 milimetre including 3 coats of oil painting etc. complete. 24 3.00 Providing and fixing M-40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming toIndian Standard 6524:1983 having 6 millitre diameter bars 3 numbers and stirrups at the 250 millitre center to center and fixing in wall with 6 numbers of hold fast of 12 millitre diameter bars 500 millitre long including primer and oil painting etc, complete with frame size 60 millitre x 100 millitre. 25 1.89 Providing and fixing fibre glass reinforced polyster door shutter 30 milimetre thick as per IS 14856 (2000) (reaffirmed 2006 ) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, complete. 26 2.88 Providing and fixing in position (as per I.S.1868:1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 milimetre at weight 0.547 kilogram per running metre and window frame bottom track section 61.85 x 31.75 x 1.20 milimetre at weight 0.695 kilogram per running metre, Top and side track section 61.85 x 31.75 x 1.30 milimetre at weight 0.659 kilogram per running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 milimetre at weight 0.417 kilogram per running metre. Inter locking section 40 x 18 x 1.10 milimetre at weight 0.469 kilogram per running metre and handle section 40 x 18 x 1.25 milimetre at weight 0.417 kilogram per running metre and top section 40 x 18 x 1.25 milimetre at weight 0.417 kilogram per running metre . As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 milimetre thick plain glass with all required screws and nuts etc, complete with colour Anodising with box. 27 2.88 Providing and fixing mild steel grill work for windows, ventilators 20 kilogram per square metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. 28 13.94 Providing and laying rough Shahabad Stone Flooring 25 millimeter to 30 millimeter thick and of required width in plain/ diamond pattern on a bed of 1:6 Cement mortar including cement float, striking joints, pointing in cement mortar 1:3 curing and cleaning complete 29 3.00 Providing and fixing mild steel grill gate with angle iron frame 65 milimetre x 65 milimetre x 10 milimetre with iron bars at 150 milimetre centre to center and diagonal flats as per the detailed drawing including hinges, pivot blocks locking arrangement welding, revetting with oil painting in three coats of approved colour shade. Weight of gate 35 kilogram per square metre. 30 49.60 Sand - Natural/V.S.I.(Vertical Shaft Impact Crusher)Quality Artifitial Sand B Garden Work 31 240.00 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area & stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) 32 180.00 GARDEN SOIL : Supplying on site garden soil well sieved 90% to pass through I.S. sieve of 10 mm sixe free from stones rubbish like dried grass mots and other such materials. The soil should be fresh from qarry. The colour of the soil generally be red. The soil will be measured b measuring box .(Farma) (Item includes Royalty charges ., Transporting, loading unloading etc.) lead charges for 20 k.m. is considered Spec. No.: As directed by Engineer-in-charge 33 30.00 FARM YARD MANURE: Supplying on site well decayed, well dried, well powdered, without clods and free from stones, dried grass and other rubbish material. The colur of the manure generally be black. 2. MATERIAL CHARGES The manure will be measured by measuring box. (Farma) (Item includes Transporting, loading unloading etc.) lead charges for 20 k.m. is considered Spec. No.: As directed by Engineer-in-charge 34 700.00 Preparing Shrubbery:- Excavating the ground to a required depth of 30 cms. Removing rubbish & conveying unwanted stuff to a required distance as directed. Filling fresh garden soil & manure in excavated area in3:1 proportion to a height of 30 cms. Mixing garden soil and manure thoroughly well, leveling, watering on previous night. Planting well, levelling, watering on previous night. Planting well developed shrubs plants, 0.50 mtr. height, 0.45 Mtrs, apart as dircted and maintaining till well established by watering, weedings, Stirring replacing, replacing casualatie etc. complete. Spec :As directed by Engineer-in-charge (196) 35 427.00 Planting Large flowering / shady tres :- (Minimum Height to 2M)- Digging pit with size 0.9m x 0.9m x 0.9 m removing and conveying unwanted stuff to a required distance as dircted. Filling the pit with approved excavated materials up to a height of 0.30m and remaining height of 0.60m with freash garden soil and manure in 3:1 proportion Mixing soil & manure thoroughly well, leveling as directed watering previous night, planting two to three year old minimum 2.0m height, healthy trees spacing as per specification. maintaining till well established by watering, weedings, stirrings of soil staking replacing of casualties etc. complete. Spec :As directed by Engineer-in-charge 36 306.00 Preparing Lawn (30 cms.Depth) Excavating the ground to a required depth of 30cms.Removing & conveying unwanted stuff to a required distance as directed. Filling fresh gardensoil/silt & manure in excavated area in 3:1 proportion to a height of 30cms. Mixinggardensoilandmanurethoroughly,well, leveling,watering on previous night. Planting required variety of lawn grass as directed and maintaining till well established by watering, weeding,clipping, rolling etc. complete (R.A.No.1) 37 700.00 Providing, Fixing, Testing & Commissioning of Agriculture pipe PVC Pipe 63 mm x 6 kg/cm2 of ISI standard, Jain make with all necessary fittings, including all labors, all taxes if any.etc., as per IS : 4985:2000 Make- Jain / Finolex / Kisan / Supreme PMC Park & Garden DSR (197) 38 1300.00 Providing, Fixing, Testing & Commissioning of Agriculture pipe PVC Pipe 50 mm x 6 kg/cm2 of ISI standard, Jain make with all necessary fittings, including all labors, all taxes if any.etc., as per IS : 4985:2000 Make- Jain / Finolex / Kisan / Supreme PMC Park & Garden DSR 39 1.00 Providing, Fixing, Testing & Commissioning of Filtration Unit consisting of Sand, Screen Filter for a filtering capacity of designed flow with Manual Back flush Unit conforming to IS specifications complete with all fittings, including all labours, all taxes if any Make Jain / Plastro / EPC (Clean master 25 m3/hr) Screen Filter Y Type 2.5 metal - 40cumh IS : 12786 PMC Park & Garden DSR 1919 4G-38 40 1.00 Providing, Fixing, Testing & Commissioning of ventury and accessories including all labours, all taxes if any. (Ventury Assembly Complete 1’’ ) PMC Park & Garden DSR 41 3000.00 Providing, Fixing, Testing & Commissioning Tubing with drippers and accessories including all labours, if any. 16mmIn- Line Drip Tubing of class-2 within-built 2.2L PH Non Drain Pressure Compensating (NDPC) emitters, spaced @ 0.6 mtr. Make - Jain /Netafim / Finolex / Rain Bird 42 15.00 Providing, Fixing, Testing & Commissioning of Control and safety valve with accessories including all labours, all taxes if any. (PVC Ball Valve 63 mm (Teflon seal) PMC Park & Garden DSR - 2022-23. 43 20.00 Providing, Fixing, Testing & Commissioning of Control and safety valve with accessories including all labours, all taxes if any. (PVC Ball Valve 50 mm (Teflon seal) PMC Park & Garden DSR - 22-23 44 10.00 MP 800 SR Multi Stream Rotor Popup Sprinkler with Adjustable from360° nozzle of radius 3mtr@Recommonded operating Pressure 2.8 bar, Q-0.18m³/hr (½ BSP inlet) Make Hunter/Toro/Rainbird 45 200.00 Micro Sprinkler assembly for Overhead Irrigation with adopter and anti leak, completeassembly 3.5 to 4.0 Mtr., discharge105 LPH @ 2 to 3 kg/cm2 Make - Jain / Hunter / Rainbird 46 2.00 BIRD BIN DUSTBIN (Proving and Fixing) HEIGHT : - 2.25’ DIA : - 1.25’ This dustbin is made up from FRP sheet with a 3 mm to 4 mm thick sheet of diameter 1.25 feet and given a shape of a bird with attractive colour. Work done should be as per engineer incharge 47 2.00 DUSTBIN – FISH (Proving and Fixing) General Information: Height : - 800 mmDia : - 400 mmMaterial Specification:This fish is made in pure polyester Fiberglass Reinforced Plastic of 2mm thk with MAT finish to give it a mirror image and it is corrosion resistance. This attractive fish dustbin attracts children towards it because of its eyes, nose and mouth and legs. As the children have habit of throwing the trash on the road or in the park, this encourages children to avoid littering, which creates an unhealthy and aesthetically unpleasant social environment. The fish dustbin is its shape, size and the scales of its body and fins looks like a real fish and the trash can be put through inside the mouth of the fish. Work done should be as per engineer incharge. (199) 48 2.00 BRINJAL BIN (Proving and Fixing) Height : - 950 mm Dia : - 550 mm This brinjal dustbin is made in pure polyester Fiberglass Reinforced Plastic of 2mm thk with MAT finish to give it a mirror image and it is corrosion resistance. This attractive brinjal dustbin attracts children towards it because of its eyes, nose and mouth and legs. As the children have habit of throwing the trash on the road or in the park, this encourages children to avoid littering, which creates an unhealthy and aesthetically unpleasant social environment. The brinjal dustbin has shape, size and the stem that of a brinjal which looks like a real brinjal and the trash can be put through inside the mouth 49 2.00 FROG BIN DUSTBIN (Proving and Fixing) Per No Height : - 850 mm Dia : - 600 mm This fish is made in pure polyester Fiberglass Reinforced Plastic of 2mm thk with MAT finish to give it a mirror image and it corrosion resistance. This attractive frog shape attracts children towards it because of its eyes, hands, legs. As the children have habit of throwing the trash on the road or in the park, this encourages children to avoid littering, which creates an unhealthy and aesthetically unpleasant social environment. The trash is to be put through the mouth of the frog. Work done should be as per engineer incharge. (200) 50 35.00 Providing, Fixing, Testing & Commissioning Valve Box with openable top cover with all necessary fittings, adhessives etc. complete including all labours, if any (Valve Boxes 6, Round shape with openable top green cover) Make - Jain /Toro /Nelson/ Rain Bird C Toys & Equipments 51 1.00 NET ROCK SCRAMBLER 2.1 MTR (Proving and Fixing) Rec. Age :- 5-12 years The area :- 2.5m x 1.5m Safe play area :- 3.5m x 2.5m Height :-2.1 M The rock n net climber is a combination of both rock and net climber. The platform of the rock climber is made up of 4 mm thick fiber reinforced plastic (FRP)/ROTO MOLDING( LLDPE /HDPE). The rocks are bolted on same platform, with a gradient of 65 degree from the ground. The main frame is made from 40 NB GI pipes. The net climber is made from 18 mm diameter nylon rope attached by specially designed nylon ball clamps. These ropes are attached to the pipe frame fabricated from 40 NB powder coated GI pipes with ‘U’ hooks. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should be as per engineer incharge. 52 1.00 CIRCULAR SWING (Proving and Fixing)Rec. Age :- 3 - 10 yrs. The area :- 1.5 m x 2 m Safe play area :- 2.5 m x 3 mThe leg support of this item is made up of 40 nb, while the top bar is from 50 nb powder coated gi pipes. The swing frame is made from 25 nb and 15 nb powder coated gi pipes. There are two seats provided which are made out of molded plastic in ROTO moulding process. The platform is made using aluminum chequered plate for footrest and bearing assembly is made. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should be as per engineer incharge. (202) 53 1.00 DOUBLE SWING WITH BELT ASSEMBLY (Proving and Fixing) Rec. Age : - 4-14 yrs. The area :- 3.0 m x 2.5 m Safe play area :- 4 m x 3.5 m In the double swing the leg support is made up of 40 NB GI pipes and top pipe is of 50 NB GI pipes with GI junction box with powder coating. The swing seat is made up of 10 mm thick rubber belt. The belt seat is affixed on 6 mm rubber coated GI chain. The ball bearings are mounted inside a specially designed nylon clamp of brand like SKF, FAQ.. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should be as per engineer incharge. 54 1.00 WAVE SLIDE 1.5 MT (Proving and Fixing) (FRP)/ROTO MOLDING( LLDPE /HDPE) Rec. Age :- 4 – 12 yrs. The area :- 4.8 m x 0.5 m Safe play area :- 5.8 m x 1.5 m Height :- 1.5m The attractive wave slide chute is made up of 4 mm thick fiber reinforced plastic materials. The structure comprises of 20 NB and 25 NB powder coated GI pipe. The center support is made in 80 NB powder coated GI pipe. The ladder cum railing is made 20 NB and 25 NB GI pipes. The platform is made up of 14 SWG GI sheet with anti skid for firm foot grip. There are triangular steps 16 SWG GI sheet. The chute has its end such as it causes safe landing of the child. All pipes are ‘B’ class pipes All Structures are to be Powder Coated. All Work Done As Per General Raw Material Sheet Added Below. Work done should be as per engineer incharge. (204) 55 1.00 PLATFORM MGR (Proving and Fixing) Rec. Age :- 5 - 12 yrsThe area :- 1.5 m dia. Safe play area :- 2.5 m dia.The platform of this platform MGR consists of non-skid type Aluminium chequered plate of 16 SWG. The ring on which chequered plate is based is made out of 25 NB GI pipes. The support below the chequered plate is of 40 x 40 x 5 and 25 x 5 Gi angle. The platform frame is made in 25 x 5 and 40x5 angle. It is provided with handrails of 20 NB GI pipes. The whole structure is mounted on heavy-duty bearing shaft permanently lubricated with water sealant of Brands like SKF, FAQ. The stand of this mgr platform is made out of 80 NB pipes. The foundation frame is fabricated with 40 x 40 x 5 angle. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI HDPE caps for user safety against entrapment etc all. Work done should be as per engineer incharge. (205) 56 1.00 MULTI SEATER SEE-SAW (Proving and Fixing) Age Group :- 3- 10 yrs. Product Area :- 3.0 m x 0.5 m Safe Play Area :- 4.0 m x 1.5 m Material Specification : The Multi Seater See saw comprises four roto seats. The lever consists of 20 NB and 80 NB powder coated GI pipes. The bearing used in this item is heavy duty nylon bush type. The stand for see saw is made using 50 NB GI pipe. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open end of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should be as per engineer incharge. 57 1.00 FUNNEL SCRAMBLER (Proving and Fixing) Rec. Age : - 4 - 12 yrs. The area :- 3.3 m x 2.4 m Safe play area :- 4.3 m x 3.4 m Height :- 3 m The scrambler consists of a funnel which is made from 25 NB GI pipes to form rings. The rings are supported with 20 NB GI pipes. Both of these pipes are fabricated together to form a funnel shape. It also has a ladder made from 40 NB GI pipes with steps made from 20 NB GI pipes. The leg support is made from 40 NB GI pipes. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should be as per engineer incharge (207) 58 1.00 STANDARD SEE-SAW – (Proving and Fixing) Age Group : - 4- 10 yrs. Product Area : - 2.5 m x 0.3 m Safe Play Area : - 3.5 m x 1.3 m The seats of the see-saw are made from roto moulded plastic. The lever is made up of 15, 20, 25 NB GI pipes and is fitted on 40 NB GI pipe. The bearing used is of heavy duty bush type. pipes are ‘B’ class pipes The Foundation pipes are embedded C.C. stock of size 0.45 x 0.45 x 0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should as per engineer incharge. 59 1.00 SHOULDER BUILDERProviding and fixing Shoulder Builder made from “B” Class G.I. pipe. The Center Pipe is of 100mm NB made from “C” Class G.I. pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The handle movement frame is of 25 NB & 20 NB made from “C” Class G.I. pipe. To Join the centre pipe & handle movement frame seamless pipe of 130mm dia & 3mm thickness is used. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” class G.I. Pipe, M.S. Round Plate of 250 mm dia & 10mm thickness & 25 mm X 25mm X 3mm M.S. angle. Closing caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm dia bright bar. The bearing used are of “6201” & “6205” permanent lubricated sealed bearing of reputed make like SKF, FAG. The nut bolts used for assembly are made from S.S. material. The serclips used for assembly is of 25 mm diameter. The Poly Urethin plastic bush is used for handling. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3 m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge (209) 60 1.00 Horizontal Bar Providing & fixing Horizontal Bar of height 2.1 mtr. from G.L. with G.I. Pipes of ‘C’ Class quality. The frame of the Horizontal bar shall be of 25 mm NB pipe. The vertical support pipe of 75 mm NB pipe. The total play area for the equipment shall be 3 m wide.The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3 m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge 61 1.00 Parallal Bar Providing & fixing parallel Bar of height 1.3 mtr. From G.L. with G.I. Pipes of ‘C’ Class quality. The horozontal parallel bar shall be of 40 mm NB pipe and vertical supports of 75mm pipe. The total play area for the equipment shall be 0.9 x 0.5 m. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3 mbelow ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge (211) 62 1 Back ExtensionProviding and fixing Back extension made from “B” class G.I. Pipe.The main frame of Ø90mm made from “ Class G.I. pipe, and The leg movement frame is of Ø40mm made from “C” Class G.I. pipe.The handle frame is of Ø32mm made from “C” Class G.I. pipe. The seats is fitted on the frame is made up of high quality FRP material of size 330 mm X 300 mm of thickness 3 mm & M.S. Plate of thickness 5 mm and Size 250 mm X 200 mm is used to Support it. The foundation used for fixing is consists of 25 mm X 25mm M.S. angle of 3 mm thickness. The footrests is made from Aluminum casting material, its sizes are 130mm X 310mm X5mm. For the support Ø32mm made from “C” Class G.I. pipe. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat done using the best quality brand paint or duly powder coated minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge 63 1 Sit Up Board Providing and fixing Sit up Board made from “B” Class G.I. pipe. The main frame is of 25mm NB made from “C” Class G. pipe.Perforated sheet of 2mm thickness is welded on main frame. The remaining frame of the sit up board is of 40mm & 50mm NB made from “C” class G.I. pipe. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3 m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat done using the best quality brand paint or duly powder coated minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge (213) 64 1 Triple Twister Providing and fixing Standing/Seated or Mix Triple Twister made from “B” Class Galvanized Iron (G.I.) Pipe. The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe, and the bottom support of M.S. round plate of 250 mm dia & 10mm thickness is welded at bottom. The standing frame of the triple twister is of 40mm NB made from “C” class G.I. pipe. The handle frame (Round type) of triple twister is of 25 NB made from “C” class G.I. pipe. The seamless pipe is used for joining the centre pipe frame & handle frame is made from 130mm dia with 3mm thickness. For the assembly different bushes are used which are made from 60mm with 3mm thickness seamless pipe is used. The foundation used for fixing is consists of three equal items i.e. 100mm NB made from “C” class G.I. pipe, M.S. round plate of 250 mm diameter & 10mm thickness & 25 mm X 25mm X 3mm M.S. angle. The standing plate is fitted on the standing frame is made up of 300mm dia & 10mm thickness M.S. material.Closing caps made from top quality FRP material which is of 2 mm thickness. The rest pipes are used for standing the plates is of 100 NB made from “C” class G.I. pipe is used. The Pins used are made up of 25 mm dia bright bar. The bearings used are of “6205” permanent lubricated sealed bearing of reputed make like SKF, FAG. The bushes (Stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50 mm dia. The nut bolts used for assembly are made from S.S. material. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge (215) 65 1 Leg PressProviding and fixing Leg Press made from “B” Class G.I. pipe. Thecenter pipe is of 100mm NB made from “C” Class G.I. pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The remaining outer frame is of 40mm NB made from “C” class G.I. pipe. The foundation used for fixing is consist of three equal items i.e. 80mm NB made from “C” class G.I. pipe, M.S. Round plate of 250mm dia & 10mm thickness, 25 mm X 25 mm X 3mm M.S.angle. To join the centre pipe & outer frame seamless pipe of 130 mm dia & 3mm thickness is used. The seats are fitted on the outer frame is made up of FRP material of size 330 mm X 330 mm of thickness 3 mm & M.S. Plate of thickness 5mm and Size 250 mm X 200 mm is used to support it. The footrests is made from FRP/C.I./Aluminum casting material, its sizes are 130 mm X 300 mm & 5 mm thickness. The frame of footrests consists of 25 NB made from “C” class G.I. pipe. Closing caps made from top quality FRP material which is of 2 mm thickness. The inner bushes are made from seamless pipe, its diameter is60mm& 8mm thickness. The pins used in are made up of 25 mm diameter hardened bright bar. The bearings used are of “6205” permanent lubricated sealed bearing of reputed make like SKF, FAG. The handles used are of Rubber grip. The Nut Bolts used for assembly are made from S.S. material. The bushes (stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50 mm diameter. The serclip used for assembly are of 25mmdiameter. foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge. (217) 66 1 Arm & Paddle Bike Providing and fixing Cycle made from “B” class G.I. Pipe. The main frame of Ø40mm made from “C” Class G.I. pipe. For the support of foot pedal M.S. round plate of Ø250 mm & 10mm thickness is used. The handle frame is of Ø32mm made from “C” Class G.I. pipe. The seats is fitted on the frame is made up of high quality FRP material of size 330 mm X 300 mm of thickness 3 mm & M.S. Plate of thickness 5 mm and Size 250 mm X 200 mm is used to Support it. The foundation used for fixing is consists of 25 mm X 25mm M.S. angle of 3 mm thickness. Closing Caps made from top quality FRP material with 2 mm thickness. The pins used are made up of Ø 25mm bright bar. The bearings used are “6205zz” permanent lubricated sealed bearing of reputed make (SKF/FAG). High tensile steel with galvanized nut bolts are used for assembly. The serclips used for assembly are of Ø25 mm. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge. (218) 67 1 RowerProviding and fixing rower made from “B” Class G.I. Pipe. The Main frame is of 80mm X 40mm & 40mm X 40mm CRC Pipe with 2 mm thickness. The handle frame is of 25 NB made from “C” class G.I. pipe. The Foundation used for Fixing consists of three equal items i.e. 40mm NB made from “C” Class G.I. pipe, C channel of 75mm X 40mm X 5mm & 25mm X 25mm X 3mm M.S. angle. To join the movement frame to main frame seamless pipe of 50mm dia & 3mm thickness is used. The seats which are fitted on the main frame is made up of high quality FRP material of size 330mm X 330mm of thickness 3 mm & M.S. plate of size 250mm X 200mm X 5mm is used to support it. Closing caps are made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 17mm diameter hardened bright bar. The bearings used are of “6203” permanent lubricated sealed bearing of reputed make foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge. The handles used are of Rubber grip. The nut bolts used for assembly are made from S.S. material. The bushes (Stopper) used to avoid the collusion made from Poly Urethane Plastic material of 50 mm dia. The serclips used for assembly is of 17 mm dia. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality (219) brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharg 68 1 Air Walker DIMENSIONS :- 1060mm (Length) x 810mm (Width) x 1600mm(Height). SAFE AREA: - 2.0 M x 1.8 M Air Walker Equipment made from “B” class G.I. Pipe of different NB. The main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bend at the radius of 250mm. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The leg movement frame is of 32NB made from “B” Class G.I. pipe. This link is supported with MS flat of size 60X8mm. The handle frame is of 25NB made from “B” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 25mm are made up from bright material. A24 circlips are used for assembly. The bearings used are “6205” permanent lubricated sealed bearing of repute brand likw SKF, FAG. High tensile steel galvanized nuts & bolts are used for assembly. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 250mm X 115mm X 3mm thick MS plate. To build structure bushes are used which are made from M.S.seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. Bolt M8 X 16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material,taxes, transport, etc complete all. Work done should be as per engineer incharge (222) 69 1 Single Chest Press DIMENSIONS:- 9000mm (L) x 650mm (W) SAFEAREA :- 2.0 M X 1.7 M. x 2150mm. (H). Chestpress equipment madeup of“B”ClassG.I.pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The center pipe is of 100NBmadeup of“B”Class G.I. pipe. The bottom welded with supportof M.S.round plate of Ø250mm &10mm thickness.The connecting pipes are made up from 25NB “B”class G.I.pipe. The handle frame is made up from 25NB & 32NB “B”class G.I.pipe. To build structure bushes are used which are made from MS.seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush isused. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm&10mmthick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. Foundation cover Closing Cap is madefrom HDPE / LLDPE Material.The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mmX 300mm X 2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Closing Caps are made up of high quality HDPE / LLDPE material. Pins used of Diameter 25mm and 17mm are made up from bright material. The bearings used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand like SKF, FAG. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for locking is made up of A24mm & A16mm. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge 70 1 Cross Trainer DIMENSIONS:-1320mm (Length)x 600mm (Width) x 1750mm. (Height). SAFEAREA:-1.77x1.2Mtr. Crosstrainer equipment madefrom“B” ClassG.I.Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Dia. of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The main frame Pipesareof80NB “B”ClassG.I.Pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of Ø250mm &10mm thick. The Handle Frame is made up of 25NB “B” Class G.I. Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe supported with 25mm X 25mm M.S.angles of 2mm thickness and 20mm 40mm MS square pipes of 2mm thickness. To build structure bushes are used which are made from M.S. seamless pipe of 60mm OD. With 5 mm thickness. The foot rests are made from HDPE / LLDPE material of size 130mm X 310mm X 5mm thickness and mounted on M.S.Plate of Size 130mm x 310mm 3mm thick Closing Caps are made up of highquality HDPE / LLDPE Plastic material. Pins used of Diameter 35mm, 25mm, and 17mm are made up from bright material. The Bearings used are of “6007zz” “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand like SKF, FAG. High tensile steel with galvanized nuts and bolts are used for assembly. A16 , A 24 mm circlips are usedforassembly. Bolt M8X16 mm and NY lock nut of M8 made of SS are used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. 71 1 Single Seated PullarDIMENSIONS:-1900mm (L) x 740mm (W) x 1920mm. (H).SAFEAREA:-1.2 M x 3 MSeated puller equipment made-up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The center pipe is of 100 NB made from “B” Class G.I. pipe. Bottom support is of M.S. round plate of Ø250mm & 10mm thickness is welded. All linkages are made up of 25NB “B” class G.I. pipe. The handle frame is of 32NB “B” class G.I. pipe. The seat frame is of 32NB “B” class G.I. pipe, To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solidbar bush is used. The foundation used for fixingis a structure and made from center pipe of G.I. of 80 NB “B” class. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. Foundation cover Closing Cap is made from HDPE / LLDPE material. Theseats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mmX 300mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Pins used of Diameter 25mm and 17mm are made up from bright material. The bearings used are of “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand like SKF, FAG. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A16. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3 below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron (227) thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge (228) 72 1 Sit Up Board Double PRODUCT DIMENSIONS: - 1950mm (L) x 1350mm (W) x 700mm (H). SAFE WORKOUT AREA: -2500mm (L)x 1600mm (W). The Sit up Board double made from “B” Class GI pipe. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The Sit up Board double made from “B” Class GI pipe. Center column made from 100mm NB “B” class G.I. Pipe. The remaining frame of the sit up board is of 50mm NB made from “B” class GI pipe. The powder coating is done with Fiber reinforced Plastic sheet of 3mm thickness is Bounded on 25mm NB (G.I.) “B” class pipe of mainframe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm M.S. square pipes of 2mm thickness. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge (229) 73 1 Sky WalkerDIMENSIONS :- 1650mm (L) x 700mm (W) x 1650mm.(H) SAFEAREA :- 2.7 m x 1.6 m.Sky Walker Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bend at the radius of 250mm. The legmovement frame is of 50 x 50 mm x 3mm thick MS square pipe. Sleeves are made up of 100 mm OD M.S. pipe with thickness 5mm. This results in easy replacement of bearings, pins and handle. The handle frame is of 25mm NB made from “B” Class G.I. pipe. The foundation used for fixingis a structure and made from center pipe of G.I. of 80 NB “B” class. Welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. Two foundations are provided for rigid support. The foot rests made from HDPE / LLDPE material of size 130 X 310 X 5mm. Closing Caps are made up of high quality HDPE / LLDPE material. The pins used are made up of Ø 25mm bright material. Pins are fixed at the outer end with M8 grub screws and Dia. 8mm SS ball. The bearings used are “6205zz” are permanent lubricated sealed bearing of reputed brand like SKF, FAG. High tensile steel with galvanizednuts & bolts are used for assembly. The cerclips used for assembly are of A24 type. TThe foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of 74 1 Thai - Chi Spineer (2 Wheel) DIMENSIONS:-1000mm (Length)x 500mm (Width) x 1450mm (Height). Safe Area :- 1.9 Mtr X 1.9Mtr Thai chi spinner Equipment made up of “B” Class G.I.pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The center pipe is of 100 mm NB made up of “B” Class G.I.pipe. The handle movement round frame is made up from 25 NB “B” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 100 mm NB “B” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25mm X 25mm M.S.angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. Closing Caps are made up of high quality HDPE / LLDPEmaterial. The pins used are made up of Ø25mm of bright material. •The bearing used is “6201zz” & “6205zz” permanent lubricated sealed bearing of reputed brand like SKF, FAG. High tensile S.S. nut bolts are used for assembly. Foundation cover Closing Cap is made from HDPE / LLDPE. The cerclips used for assembly is of A24 and A11. The nylon bush is used for handle knob. Bolt M8 X 16 mm and Nylock nut of M8 made of SS are used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge 75 1 Horse RiderDIMENSIONS:-1180mm (Length) x 400mm (Width) x 1400mm.(Height). SAFEAREA:-2.2 Mtr x 1.4 Mtr.Horse rider equipment made from“B”class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe inmillimeters, Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The main frame of 100NB made from “B” Class G.I. pipes welded with M.S. round plate of Ø250 mm &10mm thick, Seat provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. The foundation used for fixingis a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. The leg movement frame is of 32NB made from “B” G.I.pipe. The handle frame is of 32 NB made from “B” Class G.I. pipe. The footrests are made from 25 NB “B” class G.I. pipe. Pins used of Diameter 17 mm are made up from bright material. The bearings used are “6203zz” permanent lubricated sealed bearing of reputed brand like SKF, FAG. High tensile steel with galvanized nuts &bolts are used for assembly. The circlips used for assembly are of A24mm. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge (233) 76 1 Inversion Machine DIMENSIONS:-1700mm (Length)x 750mm (Width) x 1530mm. (Height) SAFEAREA:-2.7Mtrx1.6Mtr. Inversion machine Equipment made from“B” class M.S.Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The main frame pipe is of 80mm NB made from“B”Class M.S. Material. The outer ring of inversion machine is 25mm NB made from “B”Class M.S. pipe. For connecting the rotating frame to main frame 32mm NB “B”Class GI pipeis used. The movement frame is of 50 x 50mm x 2mm thick CRC square pipe. The handle frame is of 25mm NB made from“B”Class M.S. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. Closing Caps are made up of high quality HDPE / LLDPE material. The pins used are made up of Ø25mm bright material. The bearings used are “6205zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of Ø25mm. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. (234) 77 1 Pommel HorseDIMENSIONS :- 2000 mm (Length)x 690 mm (Width) x 640mm(Height).SAFEAREA :- 5 M x 3.5 Mr.Pommel horse equipment made from“B” Class G.I.pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The main frame of 80NB and 50NB made from“B”Class G.I. pipe. The handle frame is of 25NB made from “B” Class G.I. pipe. 20mm x 40mm MS square pipes frame is placed on the 25mm x 25mm 2mm M.S. L Angle with 40 x 10mm thickness flat is used for support. High tensile steel with galvanized nuts and bolts are used for assembly. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated ofminimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge (235) 78 1 Providing, Erecting, Installing, Commissioning and giving Test of 7.5 HP SPV Pumping System, Submersible pump (DC/AC) suitable for Bore well 115 to 150mm dia. (6750 Watt) with all necessary attachments & (6750 Watt PV Module) as per Techinical Specifications mentioned in MNRE Guidelines 2015-16 D.C. Motor Pump Set (with Brush less D.C.) etc complete. MNRE Bench Mark Cost of Order No. 32/24/2020- SPV Division dated 26 October 2021 with (5Year CMC) as per following technical specification. a) Solar Panel (PV Array) - 4800 WP. b) Motor Pump set -5.0 HP, 4800 Watt submersible pump set brushless D.C. pump (B.L.D.C.) c) PV Module mounting structure - M.S. hot dip galvznised, with passive or manual tracking of three time d) 150 Meter Shut off dynamic head. 79 1 Auto start/stop/ capability with remote tank full sensing and contrl via GPRS This will include: -sensors Data transmission to server - controller Based upon tank is full or not. - Power Supply to the dara collection/transmission unoit. This power supply needs to be battery backed ( with lithium ferrous phosphate battery 20AH x 12V) - Charge controller for battery charging -40Wp solar panel - The operation will be two sim-card based where one sim card is used to transfer datd from water tank to server and other one to receive the data and contrl command on the pump end Price of supply and Installation. 5 years CMC and maintenance (236) 80 1 Auto switching between Grid and Solar Pump can be operated on both solar and grid, Solar is given first preference. In case Solar Power generation is not sufficient to run pump, then pump operation will switch to grid unit till solar power is available. 81 1 Control Panel - Suitable for above pump set with arrangement of dry run protection, float switch & rain prevention box etc. ( As per water supply & sanitation dept. G.R. amendment No. Grapapu-5310/Prakra217 dated 24/07/2015) 82 1 Supplying & erecting flat flexible 3 core 4 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. 83 1 Supplying, installing and testing earthing with copper earth plate size 60 x 60 x 0.315 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover with minimum 25 kg Carbon based environment friendly back fill ground enhancing compound complete with all accesories of copper materials & recording the results as per specification no EAEP/ EF 84 0.835 Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates, etc. as per detailed design and drawing or as directed by Engineer-incharge including cutting, fabricating, hoisting, erecting and fixing in position, making riveted / bolted / welded connections and one coat of anticorrosive paint and over it two coats of oil painting, etc. complete. (Bd-C-8/278) 85 35 Providing & erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL (237) 86 35 Providing and erecting galvanised 1000mm double arm sword type bracket with FRP dome and ball as per specification no. OH-PL/BKT 87 35 40-Watt Philips Solar Light with Solar Panel – 4-Year Warranty 88 2 Making M-20 cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 2m depth including excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 12.5m raising lowering high mast). 89 2 Supplying Installing Testing and Commitioning Solar Mini Highmast with Dimming Arrengement with 40W Luminare X 4 Nos. 240 Ah 12.8 V Lithium Ferro Phosphet (LiFePO4) Battery (60Ah x 4 Nos.) 600 Wp Solar Photo Volatlic Models (Min 300 W Peak x 2 Nos. Module) Solar Panel Module with Anti Dust Coating and Fitted with Birds Spike Mounted on GI Octagonal Pole 7 mtr. Height with 3 mm thickness Hot Dip Galvanised with Bottom 130 mm A/F & Top Dia 70 mm A/F along with required Accessories Suitable Foundation Earthing All Brackets Such as for Solar Plate Fitting Bracket etc. Water Proof Battery Box sultable solar Inverter/ Charged Controller Timer Setting Arrengement GI / Powder Coated Module Structure with 5 Years On Site warranty 90 1 Testing Charges for conducting BASIC TEST OF CEMENT.Standard Consistancy Fineness, Specific Gravity, Setting Time ( Initial & Final ), Compressive Strength and Soundness test. (238) 91 2.00 Testing Charges for conducting BASIC TEST OF AGGREGATE. Water Absorption, Specific Gravity,Impact Value Crushing Value test. 92 4.00 Testing Charges for conducting BASIC TEST OF AGGREGATE. Sieve Analysis test. 93 4.00 Testing Charges for conducting BASIC TEST OF AGGREGATE. Flakiness Index/ Elongation Index test. 94 7.00 Testing Charges for conducting FINE AGGREGATES. Fineness Modulus (Sieve Analysis),Silt & Clay Content test. 95 1.00 Testing Charges for conducting BRICKS Water Absorption (Set of 5 Bricks), Compressive Strength ( Set of 5 Bricks), Efflorescence (Set of 5 Bricks) test. 96 11.00 Testing Charges for conducting CONCRETE Compressive Strength OF Cement Concrete Cube (Set of 3 cubes) test. 97 4.00 Testing Charges for conducting CONCRETE PAVING BLOCKS Compressive Strength,Water Absorption test (Set of 8 Blocks). 98 4.00 Testing Charges for conducting MORTAR Compressive Strength ( Set of 3 Cubes) test. (239) 99 1.00 Testing Charges for conducting STONE/ RUBBLE Crushing Value/ Compressive Strength,Water Absorption & Specific Gravity test. 100 1.00 Testing Charges for conducting SOIL / MURUM Liquid limit plastic Limit test. 101 1.00 Testing Charges for conducting SOIL / MURUM Compaction Test (Proctor Density). 102 1.00 Testing Charges for conducting SOIL / MURUM C.B.R. Test (Lab) Excluding compaction test. 103 1.00 Testing Charges for conducting SOIL / MURUM Field Density test by Sand Replacement Method. 104 1.00 Testing Charges for conducting STEEL BAR TESTING Upto 16 mm (Set of 3 Bars) 105 1.00 Testing Charges for conducting STEEL BAR TESTING Above 16 mm (Set of 3 Bars) (Tensile strength, %, Elongation, Yield Stress,Weight-Per Meter, Bend / Rebend Test, Proof Stress). 106 412.44 Royalty Charges 107 412.44 Surcharge 2% on Royalty Charges
