Tender For special Repair To Bldg No P 143 Jcos Or Md Accn In Umed Vihar At Rms-- 1 Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed. 2 Demolition of unreinforced cement concrete of any description and inany position not otherwise specifically provided complete all as specified and as directed. 3 Taking downchowkats with shutter n.exc 1.5 Sqm each (without taking off shutters from the frame) complete all as specified and as directed. 4 Taking downchowkats with shutter exc 1.5 but not exc 4 sqm each (without taking off shutters from the frame) complete all as specified and as directed. 5 Taking down door shutter exc 1 sqmtr but nex 2 sqmtr eachand removing to store complete all as specified and as directed. 6 S&F in repairs/replacement of 750 ltr capacity rotational moulded polythylene water storage tanks double layer(cylindrical, vertical with closed top ), including 20mm diaBall valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms), all specified in SSR Part-I complete all as specified and as directed. 7 Formwork to chajjas including edges for flat rough finished surfaces complete all as specified and as directed by Engineer-in-Charge. 8 M & L for RCC (1:1.5:3) type A-1, Nominal Mix (using 20 mm gradedstone aggregate) as in chajjas complete all as specified and as directed. 9 M&L for TMT steel bars 10 mm dia and above, as in reinforcement for concrete, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and as directed. 10 All as peritem No 09.00 (here-in-before)but above 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders. 11 M&L for Cement Concrete type E-2 (1:5:10) using (using 40 mm graded stone aggregate) as in foundation and mass concrete/sunken floors complete all as specified and as directed. 12 M&L for Cement concrete type B-1 (1:2:4), as in levelling course (using 20 mm graded stone aggregate), 25mm thick complete all as specified and as directed. 13 M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular),area of each tiles exceeding0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in whitecement mixed with pigment to match shade of tiles,laid over and including 15 mm thick screed bed in CM (1:6) including dismantling of old unsv tiles complete all as specified and as directed. 14 M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular),area of each tiles exceeding0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white/colouredcement mixed with pigment to match shade of tiles,laid over and including 15 mm thick screed bed in CM (1:6) including dismantling of old unsv tiles complete all as specified and as directed. 15 M&L for Glazed ceramic coloured tiles in vertical surface 3350 x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile , over and including baking coat of 10 mm thick in CM (1:4) including dismantling of old unsv tiles complete all as specified and as directed. 16 M&L for preparing the sunken floor slab as specified and appying cement plaster coat laid to slope average 20mm thick in CM (1:3) finished even and fair and applying evenly a tack coat of industrial bitumen 85/25 @ the rate of 1.2 kg per sqm etc complete all as specified and directed. 17 M&L for Water proofing treatment by applyingbituminonus primer @ 0.20 kg/sqm providing and laying 3mm thick APP modifide water proofing membrane weighing not less then 3.00 kg/sqm reinforced with non woven polyster mett weighingnot less then 160gm/sqm having soften point not less then 140 degree centi grade, longitudinal tensile strength not less then 650N/Sqm, tearing strength of 180 N, by torch application including minimum 10cm side overlap and 15cm end over lap and over the membrane. 18 M&L preparation of roof surface and applying one coat of aluminium primer (reflux) @ 0.10 kg /m applied on treated bituminous membrane complete all as specified and directed. 19 M&L for screeding 10 mm in cement mortar (1:4) on brick/concrete roof surfaces, using WPC (WPC measured and paid separately), surfaces finished even and smooth without using extra cement etc complete all as specified. 20 S&F Pressed steel door frames of size 105 X 60mm (Thickness of MS Sheet 1.25mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling of steel chowkhats with Cement concrete (1:3:6), type C-2 (using 40mm graded stone aggregate)including necessary form work complete all as specified and as directed. 21 S&F Pressed steel door frames of size 125 X 60mm (Thickness of MS Sheet 1.25mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,including filling of steel chowkhats with Cement concrete (1:3:6), type C-2 (using 40mm graded stone aggregate)including necessary form work complete all as specified and as directed. 22 S&FPlain, solid straight chowkat and frames, wrought, frmedrebated on the solid, rounded or chamfred put together with glue pinned at joints , supplied and fixed in 2nd class hard wood. 23 S&F35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sidescomplete all as specified and as directed. 24 M&L for 0.90mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions complete all as specified and as directed. 25 S&F 35 mm thick factory made second class hard wood glazed and skelton shutter, open rbatd and prepared to receive glass, gauze etc (with out sash bar ) edges of framing plain, camfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part -I section 8 clause 8.42(a) supplied and fitted to chowkat complete all as specified and as directed. 26 Supply and fix stainless steel wire cloth 0.36 nominal dia of wire and average width apperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutter complete all as specified and as directed. 27 S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified (Thickness or powder coating notless than 50 micron) complete all as specified and as directed. 28 S&F powder coated, Anodised aluminium window and ventilator shutters (Triple track), fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. (Thickness or powder coating not less than 50 micron) complete all as specified and as directed. 29 All as per item No 28.00 (here-in-before) but in ventilators, with sliding type lovers and provision for fixing exhaust fan/fixed type Glazing a(Area of ventilator not exceeding 0.50 Sqm). 30 S&F Aluminium decogrills made out of fixed indepently on outsode of sliding window system in Aluminium C channelon top & Bottom, wt of aluminium alloy grill not less than 1.5 Kg/m2 complete all as specified and as directed. 31 Supply and fix sheet glass selected quality 4.0 mm thick, any size, tinted of approved colour fixed with rubber beading complete all as specified and as directed. 32 M&L for Preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink wood primer complete all as specified and as directed. 33 M&L for Preparation of old wooden surface and applying two coats of synthetic enamel paint over a coat of pink wood primer complete all as specified and as directed. 34 S & F,Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specificationcomplete all as specified and directed. 35 S&F for Factory made solid panel PVC doorshutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed. 36 S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed. 37 S&F 100 mm thick Butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed. 38 S&F 75 mm thick Butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed. 39 S&F Aluminium bow handles, cast type, anodised 150 mm long complete all as specified and directed. 40 S&F Aluminium bow handles, cast type, anodised 75 mm long complete all as specified and directed. 41 S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. 42 S&F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. 43 S&F in repairs 18 mm thick prelaminated Medium density fibre board, Exterior grade, fixed to timber frame-work with stain less steel screws fixed in repairscomplete all as specified and directed. 44 S&F 75 mm Hasp and staple, safety type, aluminium anodised mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. 45 S&F Continuous (piano) hinges, mild steel bright finish or electro galvanised with flap (when open) 40 mm, fixed with steel screws complete all as specified and directed. 46 S&F 200mm long mild steel ordinary rat tail rod pattern springs including roller and roller complete complete all as specified and directed. 47 M&L for brick work with sub class B bricks (using old size burnt bricks) straight or curved on plan exc 6m mean radius built in CM (1:6) including demolition of old brick work complete all as specified and as directed. 48 M&L for brick work with sub class B bricks (using old size burnt bricks) straight or curved on plan exc 6m mean radius in half brick thick wall built in cement mortar (1:4) including demolition of old brick work complete all as specified and as directed. 49 M&L for Rendering 10 mm thickin CM (1:6) on brick work/concrete surfaces finished even and fair without using extra cement including taking down old plaster from its position complete all as specified and as directed. 50 M&L for rendering 15 mm thick cement plaster in CM (1:4) on brick work/concrete surfaces mixed with WPC @ 3% by weight of cement content ,finished even and fair without using extra cement including taking down old plaster from its position complete all as specified and as directed. 51 M&L for rendering 5 mm thick cement plaster in CM (1:3) on ceiling surface finished even and fair including taking down old plaster from its position complete all as specified and as directed. 52 M&L for Complete removal of existing treatmentand applying twocoats of oil bounddistemper white or tintedon walls over a coat of alkali resistant primer over 2 mm thick wall care putty(in two layers) complete all as specified and as directed. 53 M&L for preparation of new plastered surfaces of wall applying two coats OBD white or tintedon walls over a coat of alkali resistant primer over 2 mm thick wall care putty(in two layers) complete all as specified and as directed. 54 M&L for Complete removal of existing treatment and applying 2 coats of oil bound distemper white or tinted over a coat of alkali resistant primer over 2 mm thick wall care putty(in two layers) over ceiling surfaces complete all as specified and as directed. 55 M&L for preparation newely plastered surface and applying two coats of oil bound distemper white or tintedover a coat of alkali resistant primer over 2 mm thick wall care putty(in two layers) over ceiling surfaces complete all as specified and as directed. 56 M&L for preparation of oldwall surfaces by removing the existing treatment completely and applying two coats on external wall of Antifungal exterior emulsion paint over a coat of primer and over 2 mm thick wall care putty(in two layers) complete all as specified and as directed. 57 M&L for preparation of new plastered wall surfaces and applying two coats on external wall of Antifungal exterior emulsion paint over a coat of primer and over 2 mm thick wall care putty(in two layers) complete all as specified and as directed. 58 Taking Down 15 mm steel tubing and connection including cleaning for refixing or removal to store complete all as specified and as directed. 59 Taking Down 20 mm steel tubing and connection including cleaning for refixing or removal to store complete all as specified and as directed. 60 S&F in repairs Vitreous china wash down water closet pan, (pedestal pattern), white, with and including plastic water closet seat, white, closed pattern with flat bottom, andcover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. 61 S&F in repair Vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand,brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, complete all as specified and as directed. 62 S&F in repairflushing cistern 10ltr capacity body molded from design quality high impact polly propylene critical, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and 15mm bore 450mm long PVC connection complete all as specified and as directed. 63 S&F CPVC pipes, SDR 11 , 25 mm outer dia conforming to IS - 15778 with all fittings such as Tee, bends ,elbows, unions sockets and end pieces etc to receive the fittings and fixed with solvent concealed in wall , floor and ceiling complete all as specified and as directed. 64 S&F CPVC pipes, SDR 11 , 20 mm outer dia conforming to IS - 15778 with all fittings such as Tee, bends ,elbows, unions sockets and end pieces etc to receive the fittings and fixed with solvent concealed in wall , floor and ceiling complete all as specified and as directed. 65 S&F CPVC pipes, SDR 11 , 16 mm outer dia conforming to IS - 15778 with all fittings such as Tee, bends ,elbows, unions sockets and end pieces etc to receive the fittings and fixed with solvent concealed in wall , floor and ceiling complete all as specified and as directed. 66 M&L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar (1:3) to ends or etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed. 67 S&F in repairs PVC connection low density polythene pipe 15 mm dia , 450 mm long , heavy duty with PTMT nuts complete all as specified and as directed. 68 S&F in repairs Pillar tap with aerator, cast copper alloy with capstain heads, chromium plated, fancy type, screwed down with high pressure, with or without lettered Hot or Cold with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore dia of pipe complete all as specified and as directed.Make : Cera Cat No QT F2006101 or equivalent in Hindware/Parryware. 69 S&F in repairs 15 mm bore Bib cock with wall flange and aerator,brass chromium plated with fancy type and screwed down to 15mm bore GI tubing or for brass ferule complete all as specified and as directed. Make : Cera Cat No. QT F2006151 or equivalent in Hindware/ Parryware. 70 S&F in repairs Angle stop valve with wall flange 15 mm bore of pipe brass chromium plated, screwed down, high pressure screwed both ends for iron pipe for unions and fixed complete all as specified and as directed. 71 S&F in repairs Stainless steel soap dish white of size 160 x 160 x 90 mm as approved fixed with brass screws or embedded in wall completeall as specified and as directed. 72 S&F in repairs Health faucet of brass body with wall hook and 1mtr flexible stainless steel braided rubber hose pipe fixed in repairall as specified and as directed. Make:-Cera Cat part No F 8030102 or equivalent as per make oflist attached as Appx B of tender documents. 73 S&F in repairs Towel rail 20mm chromium plated fancy type 60cm long including bracket fixed between flanges complete complete all as specified and as directed. Make : Cera Cat part F 5007103 - equivalent as per make oflist attached as Appx B of tender documents. 74 S&F in repairs Brass chromium plated over head 15 mm boreshower rose 120mm diawith 3 flow swivel jointincluding shower arm fixing to steel pipe or union complete all as directed and as specified.Make:-Cera Cat No F 7020305 shower arm F 7040104or equivalent as per make oflist attached as Appx B of tender documents. 75 S&F in repairs 600 X 450mm bevelled edgemirror of selected quality glass, mounted on 6mm thick AC building board fixed to wooden plugs withCP brass screws and cup washers complete all as specified and direced. 76 S&F PVC (SWR) pipes of dia110mm boredouble socketed in any lengthwith rubber ring joints fiexed to walls complete all as specified and direced. 77 S&F PVC (SWR) pipe of75 mm bore in double socketed in any lengthwith rubber ringjoints fixed to walls complete all as specified and direced. 78 S&F PVC Nahani traps 75 mm outlet with stainless steel cover grating complete all as specified and direced. 79 S&F PVC (SWR)bends of 75mmbore in radius complete all as specified and direced. 80 S&F PVC (SWR)bends of 110 mmbore in radius complete all as specified and direced. 81 S&F Salt glazed stone ware gully traps square or round mouthed type 150 mm x 150 mm. type P complete all as specified and as direced. 82 M&L for Cutting holes into or through cement concrete slabs ,chajjas etc reinforced or superficial areaExc 100 sqcm but N.exc 250 sq cm complete all as specified and as direced. 83 S & F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws including dismantling of old unsv Plain /corrugated steel sheeting complete all as specified and as directed. 84 S & F Pre-painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws including dismantling of old unsv Plain/corrugated steel sheeting complete all as specified and as directed. 85 M&L for applying two coats of synthetic enamel paint over a coat of red oxide,zinc chrome primer on newly prepared steel surface of any description,over 10cm width or girth,not other wise describedcomplete all as specified and as directed. 86 M&L for Preparation ofold painted surfaces of steel & Iron of any description over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) complete all as specified and as directed. 87 S&F in repairs 20 mm dia powder coated aluminium curtain railsfixing with fancy brackets and closing caps complete all as specified and as directed. 88 S&F Gun metal globe or gate valves of size 40 m dia with iron wheels head , screwed both end for iron pipe complete all as specified and directed. 89 M&L for chequered cement concrete tiles of size not less than 300x300x25mm thick laid over and including 15mm thick screed bedfor laying floor finishes in cement mortar (1:6) etc, set, jointed and pointed in neat cement slurry with grey cement and pigments complete all as specified and as directed. 90 S&F in repairs 1mm thick stainless steel sink, plugs, washers, PVC waste pipe, union, CP coupling & cantilever brackets embedded in cement and sand mortar in wall , ovesinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmrall size of sink 495mmx420mm, bowl size 410mmx330mmx 160 mm complete all as specified and as directed. 91 S&F in repairs stainless steelplate rack of standard pattern & of size 790x610x220mm thickness of stainless steel sheet shall be304 AISI including fixing to wall with 4 nos 50 mm screws & pvc rawl plugs complete all as specified and as directed. 92 S & F for4 mm thick of size 600x600mmHSPC (high pressure Steam Cured) non asbestos fibre cement reinforced multipurpose board, pre-primetered self embossed, textured designer boardE-Board Classic fixed or laid/inserted to timber/ GI frame work with screws to be fixed in ceiling flat or sloping and Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre both ways, size of grid 605 x 605mm fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any sizeincluding dismantling of old unsv ceiling boards (fibre, pulp, insulation, etc.) any thickness including cover fillets of any description and at any location complete all as specified and as directed. 93 M&L for Machine cut kota stone slab flooring 20-25 mm thick laid over 20 mm cement screed bed in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishingand rounded or chamfered for nosing complete all as specified and as directed. 94 M&L for Machine cut kota stone (20-25)mm thickin riser of steps, skirting, dadoand pillar over 15 mm thick screed bed in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishingand rounded or chamfered for nosing complete all as specified and as directed. 95 M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, laid over and including 20mm thick screed bed/bedding layer in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. 96 M&L for 75 mm thick PCC (1:3:6) type C-2 , (using 40 mm graded stone aggregate) in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and as directed. 97 Material and labour for (concelaed Type) point wiring in repairs including necessary chases cutting of wall for one light/fan/call bell point with 1.5 sqmmPVC insulated (FR-LSH) PVC sheathed multistranded copper conductor cable 1100 volts gradecontrolled by one way switchincluding 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit with all accessoriesand sunk GI box for mounting of fittings like switch, socket and fan regulator etc and making good the distrubed surfaces as per the existing complete all as specified and as directed by the Engr-in-Charge 98 Onelight pointcontrolled by one, one way switch . 99 One Ceiling fan/ exhaust fan point controlled by one, one wayswitch. 100 One 3 pin socket outlet 5 Amps on the same board with other switches. 101 One 3 pin socket outlet 5 Amps on the Independent board. 102 One bell pointcontrolled by one, one way switch . 103 One light point control by two way switch 104 All as per item No- 97.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed. 105 S&F Switch Piano, flush type single pole, one way 5 Amps complete all as specified and as directed. 106 S&F Socket outlet, 2 in 1, 5 pin 5A flush type complete all as specified and as directed. 107 S&F Switch Socket combination, 2 in 1, 5 pin 6A flush type complete all as specified and as directed. 108 S&F Switch Socket combination, 2 in 1, 5 pin 6A/16A flush type complete all as specified and as directed. 109 S&F for bell push switch 5 amps piano type flush type complete all as specified and as directed. 110 S&F bell AC 230 volts musical type complete all as specified and as directed. 111 S&F Switch piano, flush type single pole,two way 6 Amp complete all as specified and as directed. 112 S&F stepped type electronic fan regulator 100/120 Watt socket size flush type on the existing phenolic laminated sheet complete all as specified and as directed. 113 Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper conductors FRLSH quality, 1100 volts grade, drawn throughand including non metalic rigid PVC conduit with all conduit accessories (including concealing and making good to the disturbed surfaces of walls, ceiling,floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface) complete all as specified and as directed. NOTE:- Two runs of 4.0 Sq mm + one run of 4.0 Sq mm and one run of PVC Conduit and its accessories of suitable size shall be measured as one unit length. 114 S&F in repairs LED Light fitting 1 x 20 watt (4 Ft), Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with, including two Nos PVC blocks and connecting upwith flexible copper cable of size 0.75 Sq mm 3 core and flexible pipe from ceiling rose to the light fitting complete all as specified and as directed. 115 S&F in repairs 10W LED, 2, Wall mountedpolycarbonate batten internally pre-wired with electronic driver and polycarbonate diffuser and fixing the same onand including two Nos PVC blocks and connecting upwith flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting complete all as specified and as directed. 116 S&F in repairs/replacement for decorative wall mounted light fitting made up of polycarbonate including 9 watt LED lampwith B-22 basecomplete all as specified and as directed. 117 S&F ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and directed. 118 S&F in repairs Bldg Security LED 25W light fitting, drawn through including GI bracket of 25mm borelight grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holesas required and connecting upwith flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fittingcomplete all as specified and as directed. 119 Taking down carefully exisiting water heater storage 25 Ltrs Capacity, PVC connection GI Tubes, Bip taps, and stop valve safecustody and refixing, testing after compltion of the work complete all as specified and as directed. Note : All fansterns Nut and Bolts deemed to included in quoted rates. 120 S&F in repairs VTPN DPX 4 way,double door 415 Volts, 50 Hz, IP 43 IK 09 sheet steel, powder painted, with02 neutral link & 02 earth bar and cable ties for cable managementsuitablefor fixing ofMCCB asincomer and MCB SP/TP as outgoing MCB DBs incl taking down of old UNSV DBs and making good the disturbed surfaces to match with existing specification , complete all as specified and as directed..Note : MCBs will be measured and paid separately. 121 S&F in repairs MCCB 4 Pole, 415 V, Adjustable type, 100 Amps with breaking capacity 16 KAcomplete all as specified and as directed. 122 S&F in repairs MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacityincluding taking down old unsv DB and making good the disturbed surfaces to match with existing specification , complete all as specified and as directed.Note : MCBs will be measured and paid separately. 123 S&F metal clad AC socket point single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 32 Amps etc complete all as specified and as directed. 124 S&F in repairs MCB SPN 32 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DBcomplete all as specified and as directed 125 S&F in repairs MCB SP 6 to 32 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed 126 S&F in repairs exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m complete all as specified and directed. Note : Old Exhaust Fan shall be deposited to EM store yard. 127 S&F in repairs exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed.Note : Old Exhaust Fan shall be deposited to EM store yard. 128 S&F in repairs ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service valuenot less than 5.1 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed. Note : OldFan shall be deposited to EM store yard. 129 Supply, Fixing and testing of vertical type wall mounted storage water heater of Capacity 25 Ltrs BEE 5 Star rated or minimum Standing Loss of 0.511 kWh , 240V, 50Hz with Maximum power consumption of 2KW , dry powder fero glass line coating technologyfor inner tank with incoloy heating elementwith minimum4 years warranty , ABS outer body , 2 units of PVC connection pipe with length of 450mm length for hot and cold water supply with complete Accessories complete all asspecified and directed. 130 Taking down and M&L for overhauling/ servicing of ceiling fan of any size / sweep (i.e 1200/1400mm sweep) and make comprising dismantaling, cleaning internally and externally and cleaning / lubricating of bearing / bushes using fresh lubricant (Oil grease) re-assembling, checking of split pin, hook assembly & hanging andincluding provision of cable fromceiling rose or connector to fan and testing for proper functioning complete all as specified and directed. 131 Taking down burnt unsv LT UG cable of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of25 sq mm, 4 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. 132 Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified ans as directed. 133 Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified ans as directed. 134 Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified ans as directed. 135 M&L for spread fine river sand in trenches complete all as specified ans as directed. Note: Punned thickness shall be measured and paid. 136 Supply & laying tubes light grade galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 40 mm dia bore including taking down corroded GI tubing complete all as specified and as directed. 137 M&L for laying brick sub class B old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed 138 M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i)The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI cover 10 m thick, funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSRPart-II. (ii)Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.
