Tender For Provision Of Water Supply Scheme At Pooh Under Ge 863 Ews; 1 Excavating over areas, n exc 1.5m deep and gettingout in hard/dense soil complete all as specified and directed. 2 M&L for PCC (1:4:8) Type D2 using(40 mm graded stone aggre-gate) as in foundations, filling and mass-concrete or sub base of floor/ hard standing/ footpath complete all as specified and directed. 3 M&L for walling of random rubble, uncoursed well bonded, bedded and solidly hearted, stone masonary work built in CM (1:6) complete all as specified and as directed. Note :- Only quantity of PCC bond stone to be deducted from quantity of random rubble masonary. 4 S&F 110mm bore PVC (SWR) pipes single socketed in any length (6Kg/Sqcm pressure rating) and fixed in retainnig wall as spout (for weep holes) complete all as specified and as directed. 5 M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast,water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed. 6 M&L for raised pointing in cement mortar (1:4) to random rubble masonary uncoursed or brought upto course complete all as specified and directed. 7 M&L for stone boulder or broken stone hand packing (Any thickness)at back of wall over arches etc and raising (or lowering) to the required level, complete all as specified and as directed. 8 Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surfacae not exceeding 40mm to face stone for Lime or sand stone and dressing of face beds and joints, as specified of random rubble walling, uncoursed or brought upto course complet all as specified and directed. 9 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.complete all as specified and directed. 10 Removal of surplus soil to a distance nexc. 50 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed. 11 Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil comlete all as specified and directed. 12 Excavating in trenches nexc 1.5 m width and nexc 1.5 m in depth for foundation or for shafts, well cesspits, manholes etc / for laying of cable/ pipe etc nexc 10 sqm on plan and nexc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed. 13 Ditto-Depth exc 1.5m but nexc 3.0m deep 14 Ditto-Depth exc 3.0m but nexc 4.5m deep 15 M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles, raft etc and mass concrete complete all as specified and directed. 16 M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed. 17 M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in floor/ roof beam, cantilevers, lintel over 1.5m span complete all as specified and directed. 18 M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in Chajjas complete all as specified and directed. 19 M &L for Pre-cast cement concrete block masonryType C1 1:3:6 using 20 mm graded stone aggregate with solid blocks, exc. 10 cm in width and setting in cement mortar,(1:6)complete all as specified and directed. 20 M&L for 15mm thick plastering onof brick or concrete surface in CM (1:4), surface finished even and smooth with out using extra cementmixed with WPC as per manufacturers instruction complete all as specified and directed.Note :- WPC shall be measured and paid separately as supply only. 21 Supply only WPC integral water proofing compound complete all as specified and directed. 22 M&L for 10 mm thick plastering onof brick or concrete surface in CM (1:6), surface finished even and smooth with out using extra cement complete all as specified and directed. 23 M&L for formwork for rough finished sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, circular/curvedcomplete all as specified and directed. 24 M&L for formwork for rough finished sides of pillars, posts, struts, piers, columns and stanchionscomplete all as specified and directed. 25 M&L for formwork for rough finished chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed. 26 M&L for formwork for rough finished sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etccomplete all as specified and directed. 27 M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hopping for column hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 28 M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending,spirally for hopping for column hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete and all as specified and directed. 29 M&L for hard core of broken boulders/stone of gauge n exc. 63 mm, deposited, spread abd levelledwatered and rammedto a true surface in layers not exceeding 15 cm thick each layer complete all as specified and directed. 30 M&L for 100 mm thick PCC (1:4:8) type D2, (using 40 mm graded stone agg) as in sub base of floor complete all as specified and directed. 31 M&L for 25 mm thick PCC (1:2:4) type B0(using 12.5 mm graded stone agg) as in sub floor of flooring complete all as specified and directed. 32 M&L for mirror polished machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror finish polishing over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and as directedNote:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.) 33 Description same all as per item No 32 above but, as in skirting/ dado/pillar/Riser (10-12mm thick Kota stone) over and including 10mm thick rendering in cement mortar (1:4) complete all as specified and as directed. 34 M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed.Note : Joint to be provided at each interval of 3m and corner and cost of the same deemed included in quoted rate. 35 S&F rolled mild steel section for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-Acomplete all as specified and as directed.Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. 36 S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 37 S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ-150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. 38 M&L for twocoats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed. 39 M&L for preparing newly plastered surfaces of wall and applying two coats ofcement base paint over a coat of cement primer complete all as specified and directed. Note :-The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. 40 M&L for preparation ofnewly plastered surfaces of walland apply two coats of oil emulsion distemperover a coat of chalk whitening primer complete all as specified and directed. 41 S&F second class hard wood (sal) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. 42 S&F 35mm thick factory made plain framed, panelled door shutters (two panel) of IInd class hard wood rail and styles with lock rail and panel of 9 mm BWP commercial ply. The size of rail and style as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified. 43 S&F 100 mm long mild steel barrel tower bolts stove enamelled black with bright boltcomplete all as directed and specified. 44 S&F 300mm long mild steel sliding door bolt plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed. 45 S&F100 mm longMS butt hinge, medium weight, cold rolled and fixedcomplete all as specified and directed. 46 S&F 125 mm long mild steel pressed handles oval type, stove enamelled blackcomplete all as directed and specified. 47 S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed. 48 S&F factory made steel windows with side hung shutters including projecting type hinges with steel handles and steel peg stay, complete with glazing bars, dovetailedore welded completeall as specified and directed. 49 M&L for twocoats of synthetic enamel paint over a coat of pink primer including preparation of new wood or wooden base surface over 10cm width or grith complete all as specified and directed. 50 S&F PUF insulated cylindrical tank of capacity 500 Ltr capacity vertical type duly filled with PUF insulation superior quality to resist in temperature -30 to 35 degree centigrade and hoisted on plateformwith making connection complete all as specified and directed. 51 S&F 20mm bore ( minimum weight 210gms) ball valve high pressure ofPTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipes or brass ferrule and fixedcomplete all as specified and as directed. 52 S&F 20 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed,complete all as specified and directed. 53 S&F 15 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed,complete all as specified and directed. 54 S&F 3-layer PP-R Polypropylene random copolymer) 20 mm outer dia concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. 55 S&F 3-layer PP-R Polypropylene random copolymer) 25mm outer dia concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. 56 S&F vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat cover , white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device, ( excluding fixing bolts, flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc., completeall as specified and directed. 57 S&F vitreous china wash hand basin, white, flat back, size 550mm x 400mm excluding taps, chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed.Note : Rate quoted under this item deemed included fixing of taps, plug and chain and connecting up to supply pipes, wastes or traps etc. 58 S&F PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia complete all as specified & directed. 59 S&F 15 mm bore bib taps, chromium plated, fancy type, cast copper alloy with crutch handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed . 60 S & F 15 mm bore angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms)complete all as specified and directed . 61 S & F 15 mm borepillar taps, cast copperalloy, with capstan heads, chromium plated, Fancy type screwed down for pipe, high pressure , with or without lettered HOT or COLD with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed. 62 S&FPVC connection 15 mm size with PTMT nut of600 mm length complete all as specified and directed. 63 M&L for 75mm diacast iron floor trap with grating including jointing to waste pipe fixed in PCC (1:2:4) type B1,complete all as specified & directed 64 S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and laid in trenches or in floor of following size complete all as specified and as directed :- 65 110 mm bore 66 75 mm bore 67 M&L for salt glazed stone ware gully trap square or round mouthed type P of following size complete all as specified & directed :- 68 Size 180mm x 100mm 69 S&F PVC (SWR) bends any radius including necessary cutting in brick wall and making good to match with existing surface of following size complete all as specified and as directed :- 70 110 mm bore 71 75 mm bore 72 S&F 110 mm bore PVC (SWR) junction single, (single T) equal or unequalcomplete all as specified and as directed 73 S&F PVC (SWR) vent cowl of following size complete all as specified and as directed :- 74 110 mm bore 75 S&Fsoap dish of viterious china, white size 160mmx160mmx90mm embedded to wall complete all as specified and as directed. 76 S&F chromium plated brass tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed. 77 S&F Vitreous China bowl urinal flat back, sizeof 465 x 355 x 265 mm white (minimum),with grating and union for discharge pipe(excluding flushing cistern, flush pipe andwaste pipe (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed. 78 S&F 5mm thick bevelled edge best quality looking mirror of size 600x450 mm with 30mm PVC beading all around the glass, mounted over 3mm thick PVC sheet or 6mm thick AC bldg board, complete all as specified and directed. 79 S&Ftoilet paper holder of vitreous china, coloured, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. 80 S&Fchromium plated health fauset, telephonic type with CP flexible arms and hooks of approved make suitable to fix to 15mm bore CP angle valve complete all as specified and directed. 81 M&L for salt glazed stone ware (SGSW) pipe, grade A, ISI marked, laid in trenches and jointed in CM (1:1) for following bore of pipe complete all as specified and directed :- 82 150 mm bore 83 M&L concrete bed to pipes in PCC (1:4:8) type D2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid on slope and tested for following bore sewer pipe line complete all as specified and directed :- 84 150mm bore 85 S&F 20 mm dia aluminium alloy anodised curtain rails with brackets fixed complete all as specified and directed. 86 Excavating over areas, in following depth and gettingout in hard/ dense soil complete all as specified and directed :- 87 Depth not exc 1.5m deep 88 Depth exc 1.5m but nexc 3.0m deep 89 Depth exc 3.0m but nexc 4.5m deep 90 Depth exc 4.5 m but nexc 6.00 m deep 91 M&L for mild steel TMT bars 5 to 10mm dia bars as in stirrups cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 92 M&Lfor RCC (design mix) M-30 (20mm graded aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. 93 M&L for formworkfor rough finish to sides of walls, retaining wall, basement wall etc. complete all as specified and directed. 94 M&L for RCC (design mix) M-30 (20mm graded aggregates) as in walls etc.complete all as specified and directed. 95 M&L for RCC (design mix) M-30 (20mm graded aggregates) as in beam (curved) etc.complete all as specified and directed. 96 M&L for formwork for rough finish to sidesof sump beams,including supports, overhangs, etc. complete all as specified and directed. 97 M&L Formwork to sides and soffits of domes, vaults, shell roofs and arch rib curved surface in two planes complete all as specified and directed. 98 S&F mild steel work as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 steel with and including necessary drilling holes etc complete all as specified and directed.Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account. 99 M&L for RCC (design mix) M-30 (20mm graded aggregates) as in Domes, vaults, shell roofs, arch ribs and folded plates etccomplete all as specified and directed. 100 M & L forstainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. 101 M & L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted orweldedFe-410 W(Gde E-250)quality B complete all as specified and directed. 102 M&L for mild steel screw bolts (machine made) dia of neck length exc 12 nexc 20 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5 cm and n exc 30cm long complete all as specified and directed. 103 M&L 150 mm dia DI Pipe (S&S) K-9 centrifugally cast (Spun) confirming to IS 8329/2000 including supply of EPDM rubber gasket confirming to IS 5382-1985 complete all as specified and directed. 104 M&L 150 mm dia DI bend of any radius complete all as specified and directed. 105 M&L for 75 mm thick PCC (1:4:8) type D2, (using 40 mm graded stone agg) as in sub base of floor complete all as specified and directed. 106 M&L for rubber moulded coloured glossy finish chequered cement concrete tiles, ISI Marked, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 15mm thick screed bed in cement mortar (1:6) for following size of tile complete all as specified and as directed:- 107 30cm x 20cm x 25mm thick 108 M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) and set in CM (1:6) including necessary fair finish formwork complete all as specified and directed. 109 M&L for Bricks, sub class B, laid flat, laid dryin floors, old size bricks complete all as specified and directed. 110 M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregate as in surface channel and drain including saucer drain and toe wall etc complete all as specified and directed. 111 M&L for extra for forming fair finished drain, or channel, 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred, stopped ends, complete all as specified and directed. 112 Add or deduct from item No.104 for each 25 mmm girth or part thereof over or under 30Cm complete all as specified and directed.Note:- For adjustment only and quantities may be varied (Plus/Minus) to any extend as per site requirement. 113 M&L for 15mm thick plastering on fair faces of brick wall in CM (1:4) surface finished even and smooth without using extra cement complete all as specified and directed. 114 M&L for 10 mm thick plastering on fair faces of brick or concretesurface in CM (1:4) surface finished even and smooth without using extra cement mixed with WPC as per manufacturers instruction complete all as specified and directed.Note :- WPC shall be measured and paid separately as supply only.complete all as specified and directed. 115 M&L for rubberized water bar 300 mm wide and 10 mm thick to be provided in concrete structure as a sealing of the joint complete all as specified and directed. 116 M&L for fusion based epoxy coating to prevent corrosion on steel structure/steel bar complete all as specified and directed. 117 M&L for point wiring with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 Sqmm multi stranded copper conductor cable (FRLSH) with continious earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed, drawn in and including concealed PVC conduit medium grade (ISI marked), not less than 20mm dia duly concealed on wall/ ceiling or above false ceiling with fittings medium grade (Color coding of wires shall be phase, neutral and earth wire all as specified) sunk metal flush box suitable for modular fixture with and including decorative polycarbonate frame for housing modular switches, sockets, fan regulators etc including white cover plate complete all as specified and directed for following:-Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface in CM (1:3) and matching with the existing surface deemed included in quoted rates. (ii)If the contractor fail to make good the disturbed surface of wall/ ceiling etc and do not match with the existing surface of wall/ceiling to the entire satisfaction of Engr-in-Charge a recovery of @ Rs. 50/- per RM will be made from payment due to the contractor. In case of any dispute the decision of Accepting Officer will be final and binding. 118 One light/fan/exhaust fan/call bell point controlled by one way 5 Amp switch. 119 One 5 pin socket out let 5/6 Amp on independent board. 120 One 5 pin socket out let 5/6 Amp on same board. 121 Descrition same all as per item No 108 above, but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point on independent board complete all as specified & directed. 122 S&F modular switch piano, 1module, flush type button 5/6 Amp single pole one way conforming to IS: 3854 and ISI marked complete all as specified and directed. 123 S&F modular socket outlet, 2 module, five pin 2 in 1, 5 Amps, flush type, 230 volts AC circuit complete all as specifiedand directed. 124 S&F modular switch piano, 1module, flush type button 15/16 Amp single pole one way conforming to IS: 3854 and ISI marked complete all as specified and directed. 125 S&F modular socket outlet, 2 module, five pin 2 in1, 15 Amps, flush type, 230 volts AC circuit complete all as specifiedand directed. 126 S&F ceiling rose surface bakelite 65 x 25mm dia three terminals (ISI Marked) complete all as specified and directed. 127 S&F LED batten 20 Watt (Warm light) 4 ft length ultra slim square profile with extruded polycarbonate envoirmental friendly energy efficient connected with 23/0.0076 twin core PVC flexible cable complete all as specified and directed. 128 S&F LED batten 10 Watt (Warm light) 2 ft length ultra slim square profile with extruded polycarbonate envoirmental friendly energy efficient connected with 23/0.0076 twin core PVC flexible cable complete all as specified and directed. 129 S&F angle Lamp holder (with metal ring), insulated body, of PVC/ Polycorbonate with back plate (ISI Marked) suitable for batten fitting complete all as specified and as directed. 130 S&F 9 watts LED lamp B22 all as specified and directed 131 S&F LED building security light 1 x 25 W housing made out of pressure die-cast aluminium alloy with toughned glass, IP 66 protection working on 240 volts, 50 Hz, consisting of reflecting lamps wired with appropriate driver PF> 0.98 having overvoltage protection upto 440 volt, surge protection level > 10 KV, thermal short circuit protection THD< 10% made up of long life LED chip (SMD) in modular with Ra< 70, and LED lumen efficiency > 140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminaire efficiency> 120 luminous /watt power LED should be of more than 01 watt CCT should be between 5700° K- 6500 K including fixing on existing bracket including making necessary electric connection with 1.5 Sqmm, 3 core, PVC insulated copperconductor cable 1100 Volt grade complete all as specified and as directed. 132 S&F electric water heater storage type steel body with copper inner tank and heating element up to 2.00KW capacity 25 ltr BEE 5 Srar Rated complete with all cccessories such as safety valve thermostate, NRV,connection peice etccomplete all as specified and as directed. 133 S&F connecting & testing distribution board of sheet metal enclosures double door, DB SPN, 8 way IP-43, 240V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps ratingcomplete all as specifiedanddirected. 134 S&F connecting & testing MCB, 230V/ 415Vwith rupturing capacity 10 KA of following capacity complete all as specified and directed:- 135 MCB 6 to 32 Amp, SP, C series/ curve, 136 SPN 32 Amp,C series/ curve, 137 S&F exhaust fan steel body with louver shutter, heavy duty, AC, single phase, 230 V, of size 300 mm sweep, 1200 RPM and connecting up including provision of cable from ceiling rose/ connector to exhaust fan complete all as specified and directed. 138 S&F exhaust fan with louver shutter, heavy duty, AC, single phase, 230 V, of size 250 mm sweep, 1200 RPM and connecting up including provision of cable from ceiling rose/ connector to exhaust fan complete all as specified and directed. 139 S&F 10Sqmm twin core cable flat of PVC insulated, stranded aluminium conductor, 1100 volts grade heavy duty cableserved with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than one mtr apart including 4 mm dia suspension wire complete including making necessary connection etc and taking down old U/S cable complete all as specified and as directed. 140 S&F brackets made out of 50mm dia GI pipe, light grade, lenth not less than 3.00 mtr, bent to shape having an angle 120 degree, fixed with two Nos32x5 mm size flat mild steel clamps made to shape and sizeand suitable nuts bolts and washers etccompete all as specified anddirected. 141 M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground, earth pit not less than 2.25 mtr depth below ground level at any type of strata with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate, connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC (1:3:6) type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM (1:4) funnel with wire mesh, RCC pit cover of 320 x 320 x 80mm size PCC (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed. 142 Supply and laying in trenches 3- layer PP-R (Polypropylene random copolymer) 75mm outer diameter conforming to IS 15801 concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random complete fittings all as specified and directed. 143 Supply and laying in trenches 3- layer PP-R (Polypropylene random copolymer) 63mm outer diameter conforming to IS 15801 concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random complete fittings all as specified and directed. 144 Supply & fixing PP-R Gate Valve of size 75 mm dia bore (outer dia of pipe in mm) compete all as specified and directed. 145 Supply & fixing PP-R Ball Valves (brass insert) as per requirement of the site of size 63 mm dia bore (outer dia of pipe in mm) compete all as specified and directed. 146 Material and Labour High density polyethlylene pipe (HDPE) Pipes of 100 mm bore PN 10 complete with fittings all as specified and directed. 147 Supply, Installation, Testing and Commissioninghigh Pressure Multistage Pump set of 30KW/40HP motor of dicharge capacity 415 LPM at 200 mtr Head with base plate coupling and foundation with all necessary fittings as recommended by OEM complete all as specified and directed. 148 Supply, Installation, Testing and Commissioning star delta starter 40 HP, Copper Bus Bar 100A and chamber , VAF Meter, LED indicating LampRYB (set of 3), incommer MCCB 100A, ICTP Switch 100A,, single phase priventor, Earth leakage relay including Hours run meter complete fabricated MS Panel Box3.15 mm thick outdoor type all as speciifed and directed.Necessary PCC foundation and earth work demeed to be incl in above rates 149 Supply and fixing high pressure single head chemical dosing system of power input 230V, 50Hz, 40SPM, 1/30 fractional HP, pressure 5 Kg/ Sqcm of maximum output 6.5 ltr / hrs with complete accessories like lead tubing, connecting ferrule, check valves etc of following accessories.(a) High pressure single head chemical dosing system of power input 230Volt, 50 Hz , 40 SPM , 1/30 fractional HP, pressure 5 Kg/sqcm with max output 6.5 ltr/hrs with complete accessories like lead tubing, connecting ferrule, check valves etc(b) 100 liters FRP dosing tank TOP dia 540mm x bottom dia 480mm x height 575mm consisiting of water inlet line.Dosing pump inlet arrangement, Drain overflow level guage , inspection port etc complete(c) Agitator 120 Watt 900 RPM single phase flange mounted with plastic shaft and impeller with complete accessories.(d) Injection dosing system with PPM Cpntrol.Note :-(i)Required Electric connection (cable) with Electric protection and PCC foundation with working sapce for chemical dosing system will be provided by the contractor as per recommendation of OEM demeed to be included in above rates. 150 Supply only calcium hyochlorite 65% to 70% chlorine contents in granular form (calcium based Granular disinfectant for water treatement all as specified and directed. 151 Supply and fixing CS sluice valve 65mmdia suitable for 75 mm delivery pipe line complete with flanged and all fiitings all as specified and directed. 152 Supply and fixing CS Reflux valve 65mmdia suitable for 75 mm delevey pipe line complete with flanged and all fiitings all as specified and directed. 153 Supply and fixing CI sluice valve 80mm dia PN 1.0 suitable for 80 mm suction pipe complete with flanged and all fiitings all as specified and directed. 154 Supply and fixing CI foot valve 80mm dia suitable for 80 mm suction pipe complete with flanged and all fiitings all as specified and directed. 155 Supply and laying inside the water storge sump of GI Pipe Heavy grade 80mm bore fixed to suction of pump set and header with necessary fittings, reducers etc all as specified and directed. 156 Supply and laying inside the water storge sump of GI Pipe Heavy grade 65mm bore connceted to pump set delivery and header , connected to main pipe line with all necessary fittings, reducers etc all as specified and directed. 157 Supply and fixing non return sluice valve 80mm of outer dia compitable with PP-R pipe of 75 mm dia OD pipe as mentioned in item No 1 of complete with all fittings as specified and directed. 158 S&F PUF insulated cylndrical tank of capacity 1000 Ltr Vertical type double layer duly filled with puf insulation superior quality to resist in temp -30 to +35 degree centigrade alongwith hiknged top lid of same material with locking arrangement and hoisted on platform complete with making pipeline connection with the following specification :- 159 (a) Inner tank will be double layered HDPE food grade material. 160 (b) Outer 4mm thick FRP jointless casing of tank. 161 (c) Thickness of PUF insulation shall be 75mm. 162 (d) Minimum density of PUF insulationshall be 44 kg per/cum+ 10%. 163 Supply and laying in trenches 3- layer PP-R (Polypropylene random copolymer) 32mm outer diameter conforming to IS 15801 concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches , walls , hard standing , road , complete fittings all as specified and directed. 164 Supply and laying in trenches 3- layer PP-R (Polypropylene random copolymer) 40mm outer diameter conforming to IS 15801 concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches , walls , hard standing , road , complete fittings all as specified and directed by Engr-in-Charge. 165 Supply and laying in trenches 3- layer PP-R (Polypropylene random copolymer) 50mm outer diameter conforming to IS 15801 concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches , walls , hard standing , road , complete fittings all as specified and directed by Engr-in-Charge. 166 Supply and fixing lagging to pipes used in water supply or plumbing all round with 40mm thick bonded mineral wool preformed SNAP-ON-PIPE sections of density 144kg / cum conforming to IS 9842 suitable for PPR pipe of size 25mm dia complete all as specified and directed. 167 All as per ser item No 148 here in before but suitable for PPR pipe of size 32 mm dia complete all as specified and directed. 168 All as per ser item No 148 here in before but suitable for PPR pipe of size 40 mm dia complete all as specified and directed. 169 All as per ser item No 148 here in before but suitable for PPR pipe of size 50 mm dia complete all as specified and directed. 170 M & L for providing aluminium cladding over insulation of PPR pipe of size 25mm dia with aluminium sheet having thickness 0.2mm all as specified and directed 171 All as per ser item No 152 here in before but suitable for PPR pipe of size 32 mm dia complete all as specified and directed. 172 All as per ser item No 152 here in before but suitable for PPR pipe of size 40 mm dia complete all as specified and directed. 173 All as per ser item No 152 here in before but suitable for PPR pipe of size 50 mm dia complete all as specified and directed. 174 Supply & fixing PP-R Gate Valve (brass insert) as per requirement of the site of size 25 mm dia bore (outer dia of pipe in mm) compete all as specified and directed. 175 Supply & fixing PP-R Gate Valve (brass insert) as per requirement of the site of size 32 mm dia bore (outer dia of pipe in mm) compete all as specified and directed. 176 Supply & fixing PP-R Gate Valve (brass insert) as per requirement of the site of size 40 mm dia bore (outer dia of pipe in mm) compete all as specified and directed. 177 Supply & fixing PP-R Gate Valve (brass insert) as per requirement of the site of size 50 mm dia bore (outer dia of pipe in mm) compete all as specified and directed. 178 Supply and fixing ball brass float valve,high pressure, with polythene float and flynut for 25mm PPR Pipe all as specified and directed. 179 Supply, laying and testingXLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 50 sq mm 3.5 core complete all as specified and directed. 180 Supply, install, testing and commissioning LT cubical Panel of outdoor type factory made dust/vermin proof made out of CRCA sheet 3.15 mm thick CPRI approved duly powder coated having opening and locking arrangementboth in front and rear side(independent door for each item on front side) mounted on 4 Nos angle iron 50x50x6 mm, 45 cm long embedded in PCC 1:3:6 type C2 complete with aluminium bus bar ofrating 1.5 times the rated capacity of incomer, IP 65 protection, suitable cable gland for incomming and outgoing cables with lugs and connections etc required nuts ,bolts and washer incl complete control wiring with suitable size PVC copper conductor cable and provn of cable lugs etc. Including provision of following accessories/eqpt incl cable gland etc and suitable for fixing of under mentioned items:- 181 Incoming-(a) MCCB fixed thermal and fixed magnetic 4Pole 160 A 25 KA-No.01 No 182 (b) Onload changeover with advance Neutral I-O-II type 160 amps 4 pole -01 No 183 (c) Digital Voltmeter 0 to 500 Volt -01 No 184 (d) Digital Ammeter 0 to 400 Amps with CTs and selector switch - 01 set 185 (e) LED Phase Indication lamp (RYB) -01 Set 186 Outgoing (a) MCCB Adjustable thermal and fixed magnetic 4 Pole 100 A 25 KA - 02 Nos 187 (b) MCB SPN 40 Amps for PH & Operarter Room - 02 Nos 188 (c)Spare Space -01 No 189 Material & Labour for High density polyethylene pipes (HDPE) of pressure ratingPN-10 fixed complete to Road, Hard standingand over brick block etc for cable protection of size 50 mm bore all as specified and directed. 190 Material & Labour for High density polyethylene pipes (HDPE) of pressure ratingPN-10 fixed complete to Road, Hard standingof size 100 mm bore all as specified and directed. 191 M & L for Earthing complete with galvanised steel earth plate electrode 600x600x6.0mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised strip of size 32 x 6 mm earth continuity coductor by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR-I 2009, connected to main switch board all as specified. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20 mm dia GI Pipe medium grade, funnel with wire mesh and lugs, and 40 mm dia GI Pipe medium grade for protection of earthstrip complete all as specified and directed. (LP-02 + DG-04+AMF+02 = 8 Nos) 192 Supply and laying cable protection bricks, common burnt clay sub class B designation 75 for protection of UG cable laid in trenches with axis of the bricks perpendicular to the axis of the cable complete all as specified and directed. 193 Returning and filling in two parts (i) using riddled soil obtained from excavated soil upto depth of 30 cm (8 cm below cable and remaining above cable for cushioning of cable and (ii) refilling the trench of remaining depth with normal excavated soil complete all as specified and directed. Note- Excavated soil shall be riddled by using sieve to separate composite particles etc and refilling in trenches as in cable cushioning. 194 Supply, Installation, Testing and Commissioningof silent Diesel Engine capacity 58.5 KVA Gen Set developing 75.5 BHP @ 1500 RPM, 415 Volts (AC3 phase, 4 wire system of supply) driven eco friendly generating set confirming to statutoryGovtCPCB IV + emission norms level norms , compact size with Manual / Automatic starting system, sound proof enclosure, low vibration,best in class fuel consumption with electronic fuel injection system, class G3 Governing in its range, directly coupled alternator and engine , water cooled, mounted on common base plate of rigid fabricated mild steel frame platform with fuel tank 156 ltrand including all Earth work , PCC fundation for DG Set inculding 1 meter working space all around, anti vibration pads / dampers including standard control panel as per OEM and other accessories as per manufacturers design.The Gen Set should be fitted with integrated acoustic enclsure is of modular construction as per OEM of the Generating Set. Specification of DG Set and AMF control Panel shall be as specified and comprising of the following:- 195 Silent features of DG Set:-(a) High water temprature(b) Low lube oil pressure(c) Emergency stop push button outside the enclosure(d) DOC, EGR(e) Cold Start feature(f) Specially designed standard control panel is mounted inside enclosure itself(g) In buit draw in type fuel tan of 156 ltr capacity(h) UV resistant powder coating can withstand extreme environments(j) The wall of the enclosure are insulated with fire-retardant and noise absorbent PU foam as to comply with the noise level of 75 dB (A) at distance of 1 mtr in open free field environment as per ISO 8528 part 10 specified by ministry and forest.(k) Fluid drains for lube oil and fuel. 196 Diesel Engine: Diesel engine of capacity of 58.5 KVA, 04 cylinder, water cooled , Turbocharged intercooled, developing 75.5 BHP aat 1500 RPM, electric start, compression ignition, 4 stroke engine designed to run continuously @ 1500 RPM.The Diesel Engine conforms to present CPCB IV + norms.The diesel engine comprise of following:-(a) Radiator with fan(b) Electric starter motor with soft starting system(c) Electronic Governor (G3 as per ISO 8528 Part V class governor)(d) Battery charging alternator(e) Dry type Air Cleaner with service indicator(f)CRDI System(g) Lube oil and fuel filter(h) DOC, EGR(j)First fill of lube oil and coolant(k) 1 x 12 V DC Battey (105 AH) 197 Alternator : Alternator capacity of 58.5 KVA suitable for continuous opertation rated at 1500 RPM, 415 volt, 0.8 PF, 50 HZ three phase in SPDP enclosure, self-excited, self-regulated brush less, floor mounted.The alternator confirming to IS:4722, BS EN 60034-1 and will be suitable for tropical condition. 198 Acoustic Enclosure : Provision of an integral type approved and certified accoustic enclosure insulated with fire-retardant and nosie abosorbent PU foam so as to comply with nose level of 75 dB(A) at distance of 1 meter in open free field environment as per ISO 8528 Part 10 specified by Ministry of Environment and Forest include of following :-(a) The enclosure is of modular construction(b) Durable industrial locking system is provided on door.(c) The sheet metal componenets are pre-treated and are polyester based powder coated (inside as well as out side ) for long life.(d) Specially designed sound attenuators are provided to control sound at air entry and exit points in side the enclosure.(e) In build draw in type fuel of 156 ltr capacity. 199 AMF Control Panel : Supply, Installation, Testing and Commissioning the standard AMF Control Panel is manufactured 3.15mm thick CRCA an is powder coated sheet outdoor type , weather proof and long lasting finish.The AMF control panel consistss of the following :-(a) Microprocessor based Gen set controller of - 12 V DC - 01 No(b) Toggle Switch -15 A 28 V DC- 01 No(c) LED Indicating Light -12 V DC- 01 No(d) Illuminated push button (Red) - 01 No(e) Illuminated push button (Green) - 01 No (f)Slector switch for by Pass -6A - 01 No(g) Pannel Door Lock - 02 Nos(h) Control MCB 1P - 32A - -01 No(j)Fuse Terminal Block with 2A Glass Fuse- 110-240V- 10 Nos(k) Fuse Terminal Block with 5A Glass fuse - 110-240V - 01 No(l)Automotive Relay - 12 V DC - 05 Nos(m)Battery Cahrger - 12V- 2.5A- 01 No(n) Buzzer 12 V DC- 01 No 200 (o) MCCB 3P 10 KA - 100Amp - 02 Nos(p) Power contactor FP - 100Amp - 02 Nos(q) Add on Block (01 No + 1 NC)- 01 No(r)Add on Block (02 No + 2 NC) - 01 N0(s)Surge Suppressor - 02 Nos(t) CTS CL 1.0 100/5A - 03 Nos(u)Power Terminal FP - 100A - 01 No(v)Lugs for power wire - 01 Set(x)Lugs for control wire - 01 set(y)Panel box powder coated 3.15mm thick CRCA Sheet outdoor type(z) Control wire FRLS 0.75 - 4 sqmm(aa)Power cable size 8 - 01 set(ab)Hardware 58.5 KVANote :- The Gen Set controller has all the basic safeties and protection as per OEM demeed to be included in above rates.
