|
| 1 | Providing drain with brick work in cement mortar in proportion 1 : 5 with half brick thick side wall and 100 mm thick C.C. ( 1 : 3 : 6)base over one brick flat soling including 15 mm thick cement plastering in prop 1 : 3 finished with a floating coat of cement slurry as directed with necessary shuttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified . (ii) 300 mm wide and average 250 mm deep with bed slope 1 in 150 with initial depth of 100 mm |
| 2 | Providing plinth protection with bricks flat laid in cement mortar1 : 4 and finished with 15 mm thick cement plaster in prop 1 : 2 with a floating coat of neat cement finish. |
| 3 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 4 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) |
| 5 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in allcolours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. Thetiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.11.41A.1 Double charge vitrified tile polished finish of size 11.41A.1.1 Size of Tile 600 x 600 mm |
| 6 | Supplying , fitting and fixing PVC pipes of 6 Kg/ cm 2 (Supreme/ Prince) or other ISI approved including jointing , fitting and fixing with clamps etc as necessary complete at all levels including below G.L. as directed and specified (a) In exposed surfaces or in trenches(a) 110 mm dia |
| 7 | Supplying , fitting and fixing 87.5 degree PVC bend of(Supreme/ Prince) or other ISI approved including jointing , fitting and fixing with clamps etc as necessary complete at all levels including below G.L. as directed and specified (a) In exposed surfaces or in trenches(a) 110 mm dia |
| 8 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer - in - Charge . Concealed work, including cutting chases and making good the walls etc. 18.8.2 20 mm nominal dia pipes |
| 9 | Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar including filling joints with jamuna sand with common burnt clay non modular bricks (a) Brick on flat soling |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.5 / 1:3:6 ( 1 cement : 3 coarse sand (Zone - III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 11 | Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chainwith rubber plug, PVC waste pipe etc. completeincluding painting the fittings ,cutting &making goodthe walls wherever required. (Sink cock, stop cocks,waste coupling are to be paid separately.(A) Parryware Make(ii) Single Bowl with Drain Board (36” L x 18” W x 8”D) Flat Edge - Glossy (Cat.No.C853699) |
| 12 | Renewing stainless steel kitchen sink of Parryware make with PVC waste pipe etc. complete including painting the fittings, cutting & making good the walls wherever required ( Sink cock , waste coupling are to be paid separately)(ii) Single Bowl with Drain Board (40” L x 20” W x 8”D) Flat Edge - Glossy (Cat. No. C853799) |
| 13 | Renewing PVC waste pipe including removing theunserviceable materials, cutting and making good tothe floors and walls where necessary. |
| 14 | Supplying fitting and fixing C.P. bib cock 15mm dia ofapproved brand directed and specified. (G.I. & C.P pipeswill be measured separately) Parryware make (i) Bib Cock with flange (Cat. No.T3904A1) |
| 15 | Providing, fitting and fixing Chrome Plated wastecoupling complete as directed and specified.(a) Jaquar Make (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709) |
| 16 | Making suitable frame for fixing S.S. Kitchen Sink with Stainless Steel (Grade - 304) hollow section round / square tubes as directed by Engineer - in - charge |
