Tender For Repair, Overhaul And Replacement Of Damaged Equipment/Machineries Of Four Nos Existing Car Washing Platforms And Other Related Ancillary Works At Dhapa Dumping Ground.- 1 HYDRAULIC HOIST: CAPACITY- 8MT, NO. OF POST- 01, OPERATING PRESSURE- 12-16 KG/CM2 LIFTING HEIGHT-1525MM 2 CAR WASHING MACHINE: DELIVERY PER GUN- 12.5 LPM NO. OF GUNS-02 OPERATING PRESSURE- 22 KGF/CM2 MOTOR POWER- 3HP TYPE OF MOUNTING-BASE FRAME 3 PNEUMATIC GREASE PUMP: PRESSURE RATIO-50:1 WORKING PRESSURE RANGE OF AIR-4.5-10.5 AIR REQUIREMENT (FAD)- 325 LPM TYPE OF HOSE-WIRE BRAIDED ID HOSE- 06, DRUM CAPACITY- 50 LTR OIL RESISTANT, HIGH PRESSURE 4 OIL GUN: FORM FACTOR- SPRAYER, TYPE- PNEUMATIC, USAGE: OIL APPLICATION 5 HYDRAULIC OIL :- HOIST LUBE 6 INSTALLATION OF HYDRAULIC HOIST: COST OF TRANSPORTATION, ERECTION, SUPERVISION, CONCRETING AND ANY OTHER MATERIALS REQUIRED AT THE TIME OF ERECTION 7 SUPPLY AND RE-INSTALLATION OF PLUNGER, RING, WIPER, GLAND, HOIST LUB ETC. FOR 1NO. OF CAR WASHING HOIST REPAIRING AT DHAPA DUMPING GROUND UNDER SWM-I DEPARTMENT. 8 BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS, GATES ETC. A. ORIGINAL WORKS 1. M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length,fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof. II) For Structural Works in Roof Trusses etc. using joists, channels and angles of specified section weighing less than 22.5 kg/ m (3rd Corrigenda & addenda dated 04.06.2018) 9 CHAPTER - VIII SUPPLYING OF MATERIALS HIRE CHARGES OF MACHINERIES 8.29Hire charges for engaging Air Compressor machine with minimum pressure capacity of 5.0 Kg/sq.cm arrangement including all necessary equipments and operating staff, carriage, fuel, Tools and plants all complete for cutting Road / hard crust cutting with pneumatic hammer at desired point in water supply works as per direction of EIC . a) With Pneumatic hammers For minimum engagement of 8 hrs. In a day 10 BUILDING WORKS ( C ) BRICKWORKS, CONCRETE WORKS Etc. A. BRICK WORKS 1. Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. 11 BUILDING WORKS ( C ) Brickworks,Concrete Works etc B. CONCRETE WORKS 1. Cement concrete with graded jhama khoa (30 mm size) excluding shuttering In ground floor and foundation (a) 1:3:6 proportion 12 ORDINARY CEMENT CONCRETE ( MIX 1:1.5:3 ) WITH GRADED STONE CHIPS ( 20 MM NOMINAL SIZE) EXCLUDING SHUTTERING AND REINFORCEMENT, IF ANY, IN GROUND FLOOR AS PER RELEVANT IS CODES (BASED ON PWD SCHEDULE OF RATES, W.E.F. 01.11.2017 WITH CORRIGENDA DT.04.06.2018) 13 Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. ( Ref :PWD (Bldg.)-2017, It. No. 40, Page No. 43 Annexture-I , Format-B, & 2nd Corrigenda Addenda dtd-04.06.2018, p-1,2, I-43) 14 SECTION 1. ------------BUILDING WORKS (I) PLASTERING, POINTING ETC. A. ORIGINAL WORKS 15 Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. 15 PLUMBING WORKS (A)-(II) G.I. PIPE WORKS AND FITTINGS 2. Supplying, fitting and fixing in position G.I. pipes of TATA make for underground works with all necessary accessories,specials viz.socket, bend, tee, union, cross, elbow, nipple, short piece etc.including cost of all materials,jointing materials ,cutting pipes,making threads,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.Payment for painting will be made seperately) (vi) 50 mm dia. medium quality 16 Sub Total 17 GST (18%) 18 Cess (1%)
