Tender For Upgradation Of Sheep Development Block Rohama.- 1 Animal Examination Area:Earth work in excavation in foundation trenches or drains (not exceeding 1.5M in width as well as 10Sqm on plan) including dressing of sides ramming of bottoms lift up to 1.5M including getting out the excavated soil and disposal of surplus excavated soil within a lead of 50M from edge of cutting . 2 Providing and laying Stone solling /boulders Hand packed including compacting, watering including all carriages of material complete. 3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level (1:4:8) (1Cement: 4 fine sand: 8 grade stone aggregate 40mm nominal size). 4 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating eachdeposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 5 Filling under floors by Nallah Muck including watering, consolidation and all other carriages, complete job 6 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement all work up to all levels(.1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size) Crushed. (All Works up to Plinth level) raft 7 Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering. All work up to plinth level1:2:4 (1Cement: 3 fine sand: 6 grade stone aggregate 20mm nominal size) 8 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo-Mechanically Treated bars of grade Fe-500D or more. 9 Centering and shuttering including strutting propping etc. removal of form work Foundations, footings, bases of columns etc. for mass concrete. 10 Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. 11 Structural steel work in built up sections, trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer all complete. 12 Providing and fixing with High rib coloured profile sheet roofing including vertical/curved surface including polymer coated J. or L hooks,fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters but including cost of ridges valleys. 13 Providing and fixing aluminum work for doors,windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge including 4mm thick glass panes for fixed portion/shutters of doors and windows and ventillators including providing and fixing of hinges /pivots and all necessary fittings wherever required power coated almunium ( minimum thickness of powder coated of 50 microns Jindal or equivalent make16 gauge including all carriages) framework size (65-85mm) x (40-45mm) 14 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete 13.60.1 On steel work 15 Providing and laying antiskid vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is:15622 of approved make, in all colours and hades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete 600x600mm 16 Providing and fixing of12 mm thick plywood in ceiling of good quality including cost of wooden cornice as required,nails etc all complete job 17 Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position :Budloo / Fir wood 18 Applying Priming coat with ready mixed colour primer of approved brand and manufacture on wood work. 19 Painting with synthetic enamel paint to give an even shade two or more coates of approved brand and manufacture on wood. 20 Providing and Electric fitting as per details. One .lighting point includeslamp point with wiring in 1.5 sq mm pvc insulated copper wire and 2.5 mm pvc multistrand copper wire,6 amp one way switch in PVC coduits/Chaneel with bends junctions boxes etc 6 amp S pole MCB 10 ampwith swicthes all compleet job. 21 One Heating point includes03 pin heating socket with wiring in 2.5 sq mm pvc insulated copper wire and 4.00sqmm mm pvc multistrand copper wire,16 amp one way switch in PVC coduits/Chaneel with bends junctions boxes etc 6 amp S pole MCB 10 ampwith swicthes all compleet job. 22 One Fan point includesone fan with wiring in 2.5 sq mm pvc insulated copper wire and 4.00sqmm mm pvc multistrand copper wire, 1200 mm ceiling fan with dimmerin PVC coduits/Chaneel with bends junctions boxes etc 6 amp S pole MCB 10 ampwith swicthes all compleet job. 23 Repair/Renovation SDBProviding and fixing of 10mmthick MDFreadymade laminated wooden flooring of approved brand and manufature over necessarythermocol , adhesive includingbeeding all fittings complete 24 P/f of 12 mm thick imported wooden panelling over 12mm thick plywood runnerandapplying malimine polish of approved quality allfixtures , carriagescost of matrial labour upto site of work including cornice 3 x3 25 Providing and laying antiskid vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is:15622 of approved make, in all colours and hades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete 600x600mm 26 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete 27 Finishing walls with water proofing cement paint of required shade onNew work (two or more coats applied @ 3.84 kg/10sqm) 28 Painting with synthetic enamel paintof approved brand and manufacture to give even shade two or more coats including all carriages upto site of work (on wood work) 29 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer 30 12mm Cement plaster of mix 1 : 4 ( 1 cement : 4 coarse sand) 31 Apply 2mm thick wall putty on wall surfaces including all carriages and costs. 32 Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing insuperstructure above plinth level upto floor five level, Cement mortar 1:6 ( 1 cement : 6 coarse sand) incl carriages complete job. 33 Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size 34 Centering and shuttering including strutting, propping etc. and removal of form for: 35 Providing and laying gang saw cut of specified thickness, mirror polished pre- moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour andtexture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-inCharge.18 mm thick 36 Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 37 Providing and fixing P.V.C low level flushing cistern with manuallycontrolled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete:10 liter capacity -White 38 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps (01 Nos), 32 mm C.P. brass waste of standard pattern(01 Nos),including painting of fittings and brackets, cutting and making good the walls wherever required.White vitreous china wash basin size 550x400 mm with a pair of 15mm C.P. brass pillar taps. 39 Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required. White glazed fire clay kitchen sink of size 600x450x250 mm 40 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backingRectangular shape 453x357 mm 41 Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 42 Providing and fixing 15 mm nominal bore C.P. brass Wall Mixer/basin mixerof approved brand and manufacture including all fittings and fixtures, complete job 43 Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 of approved brand and manufacture including all fittings and fixtures, complete job 44 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour, 600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 190 gms. 45 Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms. 46 Providing and fixing of 100 m dia PVC Pipes (Type B) of approved brand including allied accessories like collars, door junctions, socket, bends etc and all other fittings, complete job 47 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge including all allied accessories 48 Providing and installation of 25 litre capacity water heating gyser of approved brand VENUS with all accessories complete job
