Tender For For Various Electricity Line Works,Indeposit Scheme(Running Contract), In The Jurisdiction Of Eudsd-I, & Ii Of Eudd-Iii, Gzb, Under Eudc-1, Gzb - Carriage of line material (like LT ABC, 1IKV XLPE Cable AB& 33 ky XLPE and 11KV &33KV CableJointingKitindoor/outdoortypeete.)fromElectricityStoreCentre,MeerutRoad, Ghaziabad to site of work with loading and unloading at both ends on Kachha Packka road. (One Job =1 Connection material) 2 CarriageofSTPole11mtrs.&13mtrLongfromElectricitystorecentre,MeerutRoad, Ghaziabad/J.E. Store to site of work with loading and unloading at both ends on Kachha pakka road 3 Carriage of PCC Pole 8.5 mts. Long from Electricity store center, Meerut Road, Ghaziabad .E. Store to site of work with loading and unloading at both ends on Kachha Packka road. 4 Carriage of 10KVA to 400K V A from Electricity store center, Meerut Road, Ghaziabad to site of work with loading and unloading at both ends on Kachha Packka road 5 Carriage of 11KV&33 kv CT/PT Unit from Electricity store center,Meerut Road, Ghaziabad to site of work with loading and unloading at both ends on Kachha Packka road. 6 CarriageofMeteringCubicalSetComplete,fromElectricitystorecenterMeerutRoad, Ghaziabad to site of work with loading and unloading at both ends on Kachha Packka road 7 Erection & Fixing of PCC Pole 8.5 mtr. long in LT. line after digging of suitable pits including fixing of requisite accessories as per RESPO Drawing/Norms by providing L.T.PinClamps.M.S.Flatofsize50x6&SchacleInsulatorofsize75x90mm,with proper size nuts and bolts. 8 Erection & Fixing of STP Pole 11 mtr. long &13 mtr long in 11 KV line& 33kv after digging of suitable pits including fixing of requisite accessories as per RESPO Drawing/Norms by providing F-Bracket made of M.S. Flat of size 50x6 mm, Cross Arm holding Clamps made of M.S. Flat of size 50x6 mm with proper size nuts and bolts, 9 Erection and fixing of double pole on ST Pole 11 mtr. long & 13 mtr long with fixing of M.S.Top & Dropper Channel, M.S. S/S Angle, E-Bracket, 11 KV Pin insulator with Pin, Disc Insulator with Disc fitting as per RESPO Drawing/ Norms by providing top and dropper clamps made of M.S. Flat of size 50x6 mm with proper size nuts and bolts 10 Mounting, Placing and connecting from LT/HT side of 11KV, 10 to 400K VA T/F as per RESPO Norms. 11 Mounting, Placing and connecting from LT/HT side of 11KV,&33 kv CT/PT Units as per RESPO Norms. 12 Road restoration charge for pucca road/footpath crossing as per RESPO/Drawing Norms. 13 Laying of 11 KV. XLPE Cable (3x35-3x70-3x120-3x185 sq mm ) and complition work properly as per RESPO/Norms 14 LayingofLTABCofvariouscapacityandcompletionworkproperly,asper RESPO/Norms. 15 Erection & Fixing of Distribution Box on pole by providing 02 Nos. D/B Clamps & proper size nut & bolts. 16 Providing and fixing of Suspension Clamp with Eye Hook as per RESPO/Norms. 17 Providing and fixing of Dead End Clamp with Eye Hook, as per RESPO/Nonns. 18 Makingandfillingof11KVCable&33kvJointingKit,Indoor/outdoortype,afterduly21 plumbing and taping of suitable XLPE Cable, providing, fixing and crimping of proper size good quality lugs, including cost of lugs and tape etc., as per RESPO Norms. 19 Installation of 11K V& 33kv Metering Cubical & CT/PT Complete work as per RESPO Norms. 20 Fabrication & Fixing of T-Channel on pole by providing Holding Clamps, F-Clamps & Proper size nuts & bolts, as per RESPO/Norms. 21 Grouting & fixing of stay rods (20x 1800)mm including all work of excavation, cement concrete in size (0.60x0.60x0.30)m in ratio 1:4:8 cement, sand, 40mm brick ballast as per drg. Including back filling, proper ramming ete and fixing tightening & nuzzling of stay wire 24 with stay rod with the poles of required tension as per drawing as per RESPO Drawing/Norms by providing all grouting material and stay clamp made of M.S. Flat of size 50x6mm with proper size bolts & nuts & loops. 22 Earthing of supports with MS earth Rod of (20x2500)mm long including excavation of pit anddrivingM.S.Rod3.0Mapartfromsupportand0.5mbelowthegroundleveland connection below the earth electrodes with the help of G.l. wire &e earthing lugs as per RESPO Drawing/Norms by providing proper size nuts & bolts. 23 Grouting of ST/PCC supports in CC 1:4:8 (Cement, sand & 40mm brick ballast) Grouting will be done in the block of size (450x450)mm x1/6th of full length of the support, up to ground level, 300mm plinth above the ground level with CC 1:3:6 (Cement, core sand and Stone grit) with mufting as per drawing, work includes back filling & proper ramming by providing all required grouting materials. 24 Wrappingofbarbedwireon11KVST/PCCpolesasanti-climbingdeviceforalengthof 0.9mtrs. Wire pitch/gap 13mm and fixing upper and lower end keeping lower end at a height of 2.75 mtr from the ground complete, including providing & fixing of lower end & upper end clamps made of M.S. Flat 40X5mm complete with nuts & bolts and all other required material and T&P. 25 FabricationofGuardingAngleXArm&otherrequisitesmaterialforguardingby drawing02NosG.IWireandmakingloopatsuitabledistanceasperRESPO drawing/Norms by providing holding clamps, 02Nos. Eye bolts made of M.S. round size 12mm dia- 100mm long & Cross Arm clamps made of M.S. Flat of size 50X6mm and bolts as per norms of RESPO Norms. 26 Laying, Stringing and final sagging of ACSR Weasel Conductor after binding from Insulator, as per RESPO/Drawing Norms. 27 Laying, Stringing and final sagging of ACSR Dog Conductor after binding from Insulator, as per RESPO/Drawing Norms.
