|
| 1 | Demolition of brick work or stone boulder masonary built in cement mortaror cement lime mortar including all quoins,arches,pillars etccomplete all as specified and as directed . |
| 2 | Material and labour for Brick workusing odd size sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6complete all as specified and as directed |
| 3 | Demolition of cement concrete in ground floors and pavingn exc 15 cm thickness (below or above ground level) complete all as specified and as directed |
| 4 | Material and labour for 100 mm thick cement concrete type B-21:2:4 using 40 mm stone aggregates as in floors and paving etccomplete all as specified and as directed |
| 5 | Material and labour for forming expansion joint 12 mm thick filled with preformed bituminous filler and top 30mm primed and sealed withsealing compound grade \"B\" forconcrete slab of 100 mm thick complete all as specified and as directed |
| 6 | Material and labour for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed |
| 7 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for( reinforcement cut as required to facilitate demolition) complete all as specified and as directed |
| 8 | Material and labour for reinforced cement concrete type B-1 1:2:4 using 20mm graded stone aggregate in chajjas complete all as specified and as directed |
| 9 | Material and labour for reinforced cement concrete (nominal mix ) type B-1 1:2:4 using 20mm graded stone aggregate in walls, retaining walls, basements walls, ballast walls and the like, any thickness ; above top of footings including attached pilaster and butttresses complete all as specified and as directed |
| 10 | Material and labour for reinforced cement concrete (nominal mix ) type B-1 1:2:4 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies , canopies, deck slabs and in shelves and the like complete all as specified and as directed |
| 11 | Material and labour for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses etc flat, vertical or to batter for rough finished surface of concrete complete all as specified and as directed |
| 12 | Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work n.exc 200 mm thick horizontal or sloping for rough finished surface of concrete complete all as specified and as directed |
| 13 | Material and labour for formwork to chullah hoods, chajjas, troughs and similar item including edges, flat for rough finished surface of concrete complete all as specified and as directed. |
| 14 | Material and labour for mild steel TMT bar 10mm dia and over, cut to length, bent to shape as required including cranking bending spirally for hooping for column, hookingends and binding with and including mild steel wire (annealed ) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 15 | All as per serial item No.14 here-in-before mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders complete all as specified and as directed |
| 16 | Dismantling wrought iron or mild steel work of any description not otherwise provided for as angle iron or flat iron as in post and guard bar or grating etc complete all as specified and as directed |
| 17 | Supply and fixing mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors; ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe -290 Gde E-165 complete all as specified and as directed |
| 18 | Supply and fixing mild steel expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members n exc 4sqm /kg complete all as specified and as directed |
| 19 | Material and labour for preparation of newly or previously untreated steel surfaces, of any description, over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed |
| 20 | Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings,from fecurity walls etc complete all as specified and as directed |
| 21 | Supply and fixing pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws to steel frame work complete all as specified and as directed. |
| 22 | Taking down cement plaster of any description, any thickness from external surfaces of walls/soffits etc. including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed |
| 23 | Material and labour for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool , applying cement slurry on the under layer @ 3 kg of cement per square meter, top layer 15 mm cement plaster 1:1/2:2 (1 cement : 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippingscomplete all as specified and as directed |
| 24 | Material and labour for preparation of newly plastered surface and applying two coat ofacrylic Smooth exterior paint of required shade (Camouflage) applied @ 1.67 kg/10sqm over and including a coat of exterior walls primer applied @ 2.20 kg/10 sqm as per manufacturer\"s instructions complete all as specified and as directed |
| 25 | Material and labour for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6finished even and smooth without using extra cement complete all as specified and as directed. |
| 26 | Material and labour for rendering 5mm thick on concrete surfaces, RCC Surface as on ceilings in cement mortar 1:3,finished even and smooth without using extra cement complete all as specified and as directed. |
| 27 | Material and labour for rendering 15mm thick on brick work or concrete surfaces or in chajjas/parapet walls etc in cement mortar 1:4 mixed with liquid WPC as per manufacturer\"s instructions finished even and fair complete all as specified and as directed. Note: Liquid WPCcompound shall be measured and paid separately in respective item(s) |
| 28 | Material and labour for preparation of new plastered surfaces of wallsand applying twocoats of Oil bounddistemperover and including a coat of primer complete all as specified and as directed |
| 29 | Material and labour for preparation of newely plaster surfaces of walls and applying two coats of cement based paint on external plastered surfaces over and including a coat of primer complete all as specified and as directed |
| 30 | Material and labour for preparation of newely plaster surfaces of ceiling, concrete surface or RCC surfaceand applying three coats ofwhite washcomplete all as specified and directed |
| 31 | Supply only liquid water proofing compound complete all as specified and as directed. |
| 32 | Material and labour for removal of existing iron gates of Mags of any sizeby means of machinery and crane and refitted after repair i.e greasing, oiling and welding etc the same in same opening to the entire satisfaction of Engieer-in-charge complete all as specified and as directed.Note:-All T&P and manpower required will be arranged by contractor. |
| 33 | Material and labour for greasing and oiling to steel gates/rolling shutters of any size of Mags by means of macnine etc complete all as specified and as directed. |
| 34 | Supply and fixing in repair steel rolling shutters of 1 mm thickness of laths, with out ball bearing, as specified including top cover and spring to pull up, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete; push pull or manual type complete all as specified and as directed |
| 35 | Supply and fixing in repair safety lever locks mild steel with 4 levers for rolling shutter complete all as specified and as directed |
| 36 | Supply and fixingin repair ball bearing for rolling shutters complete all as specified and as directed |
| 37 | Supply and fixingMS pipe of 100 mm dia as shaft including two coats of aluminium paint over a coat of red oxide primer complete all as specified and as directed |
