Tender For Work Of Strengthening/Beautification In Office Premises. - civil work 2 MASONRY WORKS 3 150mm thick Block wall 4 Providing and Fixing of Pantry Cabinate Boxes made up of 30mm thick marble stone as partition and 18mm thick granite to be fixed for base of 15mm nano Stone type tile on it to make it 35mm as counter base. 5 REBARING (SLAB EXTENSION) 6 Providing and fixing of pantry overhead cabinate made up of century sainik Mr grade plywood 18mm with shutter and auto hinges of approved make as per design and drawing 7 Floor Screeding Works 8 Providing & Laying plain cement concrete 50 -60 mm thick , as required in 1:3:6 (1 Cement: 3 Coarse Sand : 6 Aggregate)with coarse sand, laid to required thickness not exceeding 50mm and slopes as marked in drawings in floor screenings laid in panels not exceeding 4 Sq.M. , consolidated finished fare and cured complete in all respect. or floor repairing if required on site. 9 Dismantling 10 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 11 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead 12 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 13 Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : 14 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 15 RCC cast in SITU 16 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement.1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 17 FINISHINGWORKS 18 Cement Plaster 19 Providing plastering in CM 1:4 12mm thick for walls including finishing to line and plumb for walls. 20 Cement Plaster 21 18 mm cement plaster in two coats under layer 12 mm thick cement plaster1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cementplaster 1:6 (1 cement : 6 fine sand). 22 Gypsum Plastering 23 Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/block/ RCC work on walls & ceiling at all floors and locations, finished insmooth line and level etc. complete. 24 Water Proofing 25 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 26 SANITARY FIXTURES & FITTINGS 27 EWC 28 Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete 29 URINAL 30 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mmwith white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe,spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I.trap with outlet grating and other couplings in C.P. brass, including painting of fittings andcutting and making good the walls and floors wherever required Single half stall urinal with 5 litre P.V.C. automatic flushing cistern 31 Wash Basin 32 Supply and fixing of wall mounted basin of approved make and model, CP waste coupling, inlet connection, 15mm NB angle type stop cock with approved make and CP wall cap etc complete as per specification and drawing details. 33 Supply and fixing pillar cock for wash basin with aerators of approved make 34 Health faucet 35 Supply and fixing ofCP health faucet along with braided tube and hanging hook etc as per approved make 36 Tissue paper holder 37 Supply and fixing of toilet paper holder with flap as per approved make. 38 Soap dispenser 39 Supply and fixing of toilet paper holder with flap as per approved make. 40 Floor trap 41 Supply and fixing of uPVC floor trap with stainless steel (SS) grating as per approved make. 42 C.P. Brass fittings 43 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore 44 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore 45 Providing and fixing C.P. brass angle valve for basin mixer and geyserpoints of approved quality conforming to IS:8931 46 MISCELLANEOUS WORKS 47 CINDER FILLING 48 Providing and filling lightweight cinder as specified in the drawings or as instructed by the Project Manager. The cinder material shall be approved by the Project Manager and shall be in the proportion of 1:15 (1 cement 15 cinder). Including cost of 50mm thick cement mortar of 1:2:4 The material shall be placed in layers of 150 mm and shall compacted to ensure dense filling with no voids. 49 GRANITE COUNTER 50 Providing and fixing 18 mm thick gang saw cut, mirror polished,Granite stone slab of colour black, Cherry/Ruby red premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing of edges to give high gloss finish etc. complete at all levels. 51 Interior work 52 PARTITIONS & ASSOCIATED WORKS 53 100mm thick Full height partition (From FFL till True ceiling soffit) 54 Providing and fixing partition upto ceiling height consisting of G.I. frameand required board, including providing and fixing of frame work madeof special section power pressed/ roll form G.I. sheet with zinc coating of120 gms/sqm(both side inclusive), consisting of floor and ceiling channel50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixedto the floor and ceiling at the spacing of 610 mm centre to centre withdash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, includingfixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the framework with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to beprovided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks) 55 12mm thick MDF PANELING 56 Providing and fixing panelling or paneling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebated to be measured). Panelling for panelled and glazed shutters 25 mm to 40 mm thick: Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 12 mm thick conforming to IS:14587 57 Gypsum panelling 58 Providing and fixing12.5mm thick gypsum board panelling with GI studs of size 48mm x 34mm x 36mm x 0.55mm thick section , at spacing not exceeding 600mm bothways (horizontal and vertical), fixed onto the floor and ceiling channels. The GI C-channels of size 50mm x 32mm x 32mm x 0.55mm thick to be fixed on the floor and ceiling to hold GI studs. Boards to be joint & finished so as to have flush look including fillingfinishing edges with jointing compound paper tape/cloth gauze. All exposed edges / Corners to be provided with proprietary Angle bead /edge bead sections/corner guard as per Architects instruction. Note: All necessary accessories and consumables to be of approved make and as per manufacturers specification. 59 Skirting 60 Providing and fixing 18mm thickskirting with Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and priming coat on unexposed surface complete : 61 FLOORING 62 Carpet Flooring 63 Providing & fixing approved carpet floor - 600mm x 600mm Imported Loop pile patterned carpet .Make INTERFACE / SHAW or Equivalent.base rate-rs.120/sq.ft 64 STONE FLOORING 65 Italian stone Flooring 66 Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointingwith white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified andas directed by the Engineer-in-Charge.With 18-20 mm thick Indian Stone and joint to be filled with white cement slurry mixed with pigment to match the shade of stone including exposed edge polishing, complete. 67 Tile Flooring and wall (Toilet) 68 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size 1200mm X 1200mm 69 CEILING 70 2 Ft. x 2 Ft. Grid ceiling 71 Providing and fixing 15 mm thick false ceiling tiles at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level on the existing frame work consisting of T-sections and Lsections suitably fixed according to tile size as per direction of Engineer-in-charge. 72 Item same as 2.1. but with 12mm thick Calcium silicate board instead of normal gypsum board complete with all respect. 73 Gypsum Ceiling 74 Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks). 75 wall panel 76 UV backlit Panel 77 Providing & Fixing uv panelwith 8mm thick ply over wooden base partition. complete as per the instructions of Architect. The panels must have8mm thk ply panel backing fixed with necessary frame work for the strength to support the backlit displayleds fastened at floor and ceiling level. finished in UV panel of approved shade & make. panel to be finished in shade and colourto architects approval, 78 Matt Laquered Panneling with Design Moulding Patterns 79 Providing and fixing of Matt laquered Finish Design Moulding Patterns with fixing ofmade out of base frame of 50mm x 50mm hardwood ( Treated with fire retardant paint and antitermite ), fixed with RCC / Brick slab/wall with s.s dash faster. 12mm bwp ply shall be fixed on it. Wooden planks shall be lined on it with grooves, metal stripps and grain as shown in drg including finsh of polish glossy / matt as per approved architect. The job shall include making vertical faces and cove, light points etc complete. All are included this item as mention in detail drg. (Base Rate of Venner @ 80/- Sqft) 80 Artificial green wall 81 Providing & Fixing artificial green wallwith 8mm thick ply over woode base partition. complete as per the instructions of Architect. The panels must have8mm thk ply panel backing fixed with necessary frame work for the strength to support the backlit displayleds fastened at floor and ceiling level. finished ofpanelsl of approved shade & make. panel to be finished in shade and colourto architects approval, 82 louver 83 Providing & Fixing pvc louvers The panels must be fixed with necessary frame work for the strength to support the backlit displayleds fastened at floor and ceiling level. finished ofpanelsl of approved shade & make. panel to be finished in shade and colourto architects approval, 84 Wallpaper 85 Providing, Fixing / Pasting of Wall Papers on wall as approved design, pattern with prepration of base in smooth finish with manf. adhesives, accesories complete in all reaspects all respect as per drawing/design and details Ref. Drawing (Wall Paper base rate @85/- Sqft) 86 Plain Fabric Panneling on Walls 87 P/F/P Fabric Panelling on side wall with 8mm Mdf with Hard wood Freaming ( If required) to be fixed on wall to paste fabric on it. All exposed area to be finished with fabric as per sample approvedall respect as per drawing/design and details Ref. Drawing (Fabric base rate @825/- Rmt) (Only Surface Area shall be measured for the payment) 88 rolling blinds 89 Providing & Fixing rolling blinds. These blinds consist of a single piece of fabric or material that smoothly rolls up and down with the help of a simple control mechanism with 45mm aluminium Super Heavy Duty Tube. This also includes a spring assist control for widths over 2400mm where the drop exceeds 1500mm... Material-Polyester Fabrics 90 MODULAR FURNITURE WORKS 91 MD/VC ROOM table 92 Supply and installation of modular table of following sizes and shapes as mentioned below, of approved make, supported on made of minimum of 18 gauge, MS powder coated leg and frame support with heavy duty levelers with race ways tray . The table top shall be made with 25mm thick MDF in approved finish and shade. The edges of the table shall be finished with matching imported rigid 2mm thick PVC lipping to the profile as per the detail drawings. The shade, make of , laminate/rubberwood, metal components and accessories shall be approved by the Architects. There shall be fliptop box as per the design intent to pass the cables below the table top. All the exposed surface of the MS shall be 60 micron thick powder coated frames. Single seater-Linear Fixed Workstation in Laminate finish of size - 1800 x 1550 Wx 750mm highas per the detail drawings. 93 Cabin table 94 Supply and installation of modular table of following sizes and shapes as mentioned below, of approved make, supported on made of minimum of 18 gauge, MS powder coated leg and frame support with heavy duty levelers with race ways tray . The table top shall be made with 25mm thick MDF in approved finish and shade. The edges of the table shall be finished with matching imported rigid 2mm thick PVC lipping to the profile as per the detail drawings. The shade, make of , laminate/rubberwood, metal components and accessories shall be approved by the Architects. There shall be fliptop box as per the design intent to pass the cables below the table top. All the exposed surface of the MS shall be 60 micron thick powder coated frames. Single seater-Linear Fixed Workstation in Laminate finish of size - 900 x 550 Wx 750mm highas per the detail drawings. 95 MEETING/CONFERENCE ROOM table 96 Supply and installation of modular table of following sizes and shapes as mentioned below, of approved make, supported on made of minimum of 18 gauge, MS powder coated leg and frame support with heavy duty levelers with race ways tray . The table top shall be made with 25mm thick MDF in approved finish and shade. The edges of the table shall be finished with matching imported rigid 2mm thick PVC lipping to the profile as per the detail drawings. The shade, make of , laminate/rubberwood, metal components and accessories shall be approved by the Architects. There shall be fliptop box as per the design intent to pass the cables below the table top. All the exposed surface of the MS shall be 60 micron thick powder coated frames. 97 Full height storage 98 Providing & fixing Storagecabinets made out of 19mm commercial board /prelaminatedboard duly GLASS shutter with 1.0mm laminatein facia and balancing laminate all inside adjustable laminated shelves,50X12mm veneered finish band alaround,100mm high skirting. All surfaces having hinges to be made of marine ply necessarily. Rate should be inclusive of necessary Hardware- 140high D shaped Hetitch handle code no.011869, Lock sets, self-closing hinges, spring loaded shutter latch inside, all cabinet hardware to be As/Architects approval. (Depth of Storage :- 500mm) 99 CHAIRS 100 Supply and installation ofChairs as per selection ) as per selection 101 SOFA SETS 102 Providing and installing a high-quality sofa with premium fabric upholstery, featuring a durable wooden frame for structural support. The sofa is designed for comfort and longevity, incorporating Sleepwell foam for superior cushioning and resilience 103 LOGO 104 Providing & Fixing logo of HPDA of size 1200X1200mm as per design & drgs made in acrylic/metal over desired mdf framing including cutting,lighting & making of logo to shape 105 LOGO 106 Providing & Fixing logo of HPDA of size 1200X1200mm as per design & drgs made in acrylic/metal over desired mdf framing including cutting,lighting & making of logo to shape. 107 INTERNAL PAINT FINISH 108 PUTTY 109 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 110 Emulsion paint 111 Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqmover and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. 112 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre 113 Texture paint 114 Providing and applying Texture paint of approved shade and finish as per design and Architects Instruction. The surface to be texture painted shall be sanded and prepared to the satisfaction of Architect.Then the surface shall be finished with approved range of ARMOUR COATmake texture paint as per the manufacturers catalogue and specifications. The shade of the paint shall be approved by the Architects.(the entire system of paint including primer, putty & paint should have VOC content less than 25gms per litre) Basic price - Rs. 200/Sft + taxes 115 Enamel paint 116 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade.Two or more coats on new work over an under coat of suitableshade with ordinary paint of approved brand and manufacture 117 GLASS WINDOW 118 UPVC WINDOW 119 Supply & Installation of Modular UPVC single glazed window, with 8mm toughend glass and equavalent make hardware as per approval from architect incharge. 120 Wooden door 121 Single leaf flush door 122 Providing and fixing ISI marked flush door shutters (Make - Greenlam) as per IS code. non decorative type core of block board construction with internal frame of first classhard wood and well matched commercial 3ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including providing and fixing 4 nos. 125mm long and 3.5 mm thick stainless steel hinges, 25 mm thick African teak wooden lipping all around, nails, screws, adhesive, all necessary hardware and fixing arrangement, cutting & fixing of louvers / vision panels with 5mm thick glass including if any & fixin and polish in desired shade over a coat of approved primer etc. complete as per specification but inclusive of hardware fittings, Handles, cylinder Locks with Master key, Floor Stopper, Door Closer. Make of Hardwares - , OzoneHaffele, Hettich or Equivalent. 123 ELECTRICAL 124 Providing, Fixing, Installation, Testing & Commissioning of internal Electrical work that includePVC Conducting (in conceal/surface), wiring in.slab / wall, chasing cutting in RCC / masonry &, making the surface good, fixing MS/GI Boxes, Switches & Sockets, DB, MCB, Sub-main, inlets & outlets, Fixtures & Fittings, connections for Electrical, Telephone, TV, intercom, , other utilities etc. work in club ncluding of all required fixtures & fittings and all required connection in cluband connecting and finishing in false ceiling work etc to make the club operational and complete in all respects as per drawing and direction of Engineer-in-charge. 125 Fixing, Installation & Testing9/wledlightsround 126 LED COB LIGHT 12 WATTS 127 Fixing, Installation & Testing of Led strip . 128 LED STRIP LIGHT WITH POWER SUPPLY 129 Fixing, Installation & Testing ofHanging light 130 LED HANGING LIGHT 1200 MM 5070 PROFILE 131 MAGNETIC TRACK CHANNEL 3METRES LENGTH 132 LED MAGNETIC LAZER BLADE LENIER 12 WATTS 133 JOINTERS 134 100 WATTS 48V DRIVER FOR MAGNETIC TRACK 135 Audio Video 136 Central Control Unit: High performance digital wired conference controller unit Directly connects up to 60 units, expandable to 250 units with extension modules, Maximum power consumption 120W, RS-232 control support for third-party central control integration (camera tracking, microphone management, and meeting modes), 4-in/1-out seamless HDMI switcher, supporting 4 cameras at 1080p@60Hzwith zeroswitching delay 137 Chairman Unit:High performance Chairman Unit with High-directivity gooseneck condenser micro phone with red LED indicator ring, Microphone stem length 220mm, Low-voltage DC24V operation for enhanced safety,Signal to Noise ratio ≥65dB, Chairman-specific controls: Priority override, Delegate microphone mute,Speech request approval and management, 1.8-inch color TFT display screen showing real-time meeting data, Third-party system integration via RS-232, enabling cameratracking and remote micro phone control 138 Delegate Unit: High performance DelegateUnit with High-directivity gooseneck condenser micro phone with red LED indicator ring, Microphone stem length 220mm, Low-voltage DC24V operation for enhanced safety,Signal to Noise ratio ≥65dB,1.8-inch color TFT display screen showing real-time meeting data,Third-party system integration via RS-232, enabling camera tracking and remote microphone control 139 Surface Mount Speakers : Full-Range Driver2-way full range speaker, 60W RMS/240W peak, 70V/100V/8 ohm operation, 6.5 LF + 1 tweeter, weatherised to meet IP55 standards,ABS cabinet, mounting yoke included 140 Mixer Amplifiers : Mixer amplifier total outputpower 480W : 4-16 ohm or 70V/100V operation, Bluetooth/USB/ FM radio media player, 6 zones with individual level control per zone, 2 Aux and 3 microphone inputs with echo, repeat & delay functions, bass, treble and master controls, siren & chime functions available,heavy duty toroidal transformer 141 Digital signal Processor : 8 input 8 output DSPMatrix processor, High performance 400MHz floating point DSP processor, 48KHz 24 bit ADC& DAC, VAL DSP control software 142 Video 143 75 Display: 75 4KUHD resolution LEDDisplay with Android 11, 400 nits brightness; 16 GB Memory, Built in Wifi andCromecast,Built-in Bluetooth, Hotel mode, Meeting Mode,20W built in speakers, HDMI 2.0 X 3, AV X 1, USB X 2, RJ45 X 1, SPDIF Out x1,24/7 operational. 144 PTZ camera: 12x zoom; Video Output (HD)Interface: HDMI / Ethernet / USB 3.0; Video S/N Ratio > 50dB; Preset Positions: 256;Interface: RS-232 / Ethernet / USB 3.0. 145 Wireless presenter: Easy wireless conferencingfor small meeting rooms and huddle spaces, Interactive features: touchback, annotation, and blackboarding, Operating system: Windows 10 and higher macOS 11, Video outputs: 4K UHD (3840*2160) @ 30Hz. HDMI 1.4b or USB-CDisplayPort 1.2 (only Gen2); Audio output: HDMI; USB 1 X USB-A, 1 X USB-C; ClickShareButtons 1 or 2; ClickShare App Desktop & Mobile; Maximum number of simultaneousconnections (with Buttons and/or App): 32. 146 AV Controller Programmable networkappliance to control AV; having features such as: Ultra-Fast 1600 MIPS processor; 512 MB Onboard RAM; 1 M Non-Volatile Memory; 1 10/100 LAN Interface; 4 Digital I/O Ports; 1RS-232/422/485 Port; 3 RS-232-Only Ports. 147 Cable Cubby HDMI and USB Ports passthrough 148 Cable Cubby USB C type pass through 149 70 Meters HDMI Tx RX Set 150 USB C-C cable 151 HDMI to HDMI cable 3 M 152 USB A to USB B cable 153 HDMI to HDMI cable 15 M 154 USB A to AF 10 M 155 USB A to BM 05 M 156 HDMI to HDMI cable 01 M 157 USB A to A Cable 158 HDMI to HDMI cable 15 M 159 HDMI to HDMI cable 20 M 160 Directors Cabin 161 75 Display: 75 4KUHD resolution LEDDisplay with Android 11, 400 nits brightness; 16 GB Memory, Built in Wifi andCromecast,Built-in Bluetooth, Hotel mode, Meeting Mode,20W built in speakers, HDMI 2.0 X 3, AV X 1, USB X 2, RJ45 X 1, SPDIF Out x1,24/7 operational. 162 All in One Conference System:-All-in-one USB conferencing device that brings premium audio and video to huddle spaces to medium-sized meeting rooms up to 6 × 6 meters (20 × 20 feet). With six automatic beam-steering microphones, a 4K ultra-HD camera, and signature sound, the Videobar VB1 helps you huddle up and getmore done 163 Wireless presenter: Easy wireless conferencingfor small meeting rooms and huddle spaces, Interactive features: touchback, annotation, and blackboarding, Operating system: Windows 10 and higher macOS 11, Video outputs: 4K UHD (3840*2160) @ 30Hz. HDMI 1.4b or USB-CDisplayPort 1.2 (only Gen2); Audio output: HDMI; USB 1 X USB-A, 1 X USB-C; ClickShareButtons 1 or 2; ClickShare App Desktop & Mobile; Maximum number of simultaneousconnections (with Buttons and/or App): 32. 164 Common Backend 165 12 Port PoE network switch 166 Speaker Cable-2 conductor 14 AWG stranded,twisted, and unshielded cable, Insulation:Semi-rigid polyvinyl chloride;Jacket: Polyvinyl chloride. 167 Conferencing cable 168 Twisted Pair Cable 169 Connectors and patch chords 170 Equipment Rack: 18U Equipment Rack forhousing all rack mountable equipments with internal wiring, front glass door; heat dessipation fans; power distribution units etc.
