Repair/ Replacement Of Joinery, Floor/ Wall Tiling And Other Misc Works Of Officers Md Accn, Jcos/ Ors Md Accn, Defece Civilian Qtrs, B S Yard, Ge E/M Office Complex And Mes Installation Under Age B/R-I Of Ge E/M R R Hosp Delhi Cantt-10; 1 Demolition of brick work or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles all as specified. 2 M&L for brick work with sub class B Bricks (using old size bricks) straight or curved on plan exc 6m mean radius built in CM 1:6, complete all as specified and as directed. 3 M&L for brick work with sub-class `B bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed. 4 Taking down cement plaster of any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified & directed. 5 M&L for 15mm thick rendering on brick or concrete wall surfaces in cement mortar 1:6, finished the surface even and fair without using extra cemnent, complete all as specified. 6 M&L for 15mm thick rendering on brick or concrete wall surfaces in cement mortar 1:4, finished the surface even and fair without using extra cemnent, complete all as specified. 7 M&L for 5mm thick rendering on concrete ceiling surfaces in cement mortar 1:3, finished the surface even and fair without using extra cemnent, complete all as specified. 8 M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over 1 to 2mm thick cement base wall care putty, complete all as specified & directed. 9 M&L for preparation of newly plastered surfaces of walls and applying two coats of exterior grade weather proof paint over a coat of primer, complete all as specified and directed. 10 M&L for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper over 1 to 2mm thick cement base wall care putty, complete all as specified and as directed. 11 Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified & directed. 12 M&L 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor finishes, complete all as specified & directed. 13 M&L 10 mm thick screed bed or bedding layer in cement mortar (1:4) to receive wall tiles, complete all as specified & directed. 14 M&L for vitrified ceramic coloured tiles 8mm to 9mm thick (square/ rectangular) polished of light shade, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified. 15 M&L for vitrified ceramic coloured tiles 8mm to 9mm thick (square/ rectangular) polished of light shade, area of each tiles not exceeding 0.36 sqm, in dado/ skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified. 16 M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match, complete all as specified & directed. 17 M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in dado/ skirting etc, set and jointed in neat cement slurry and pointed in coloured cement to match, complete all as specified & directed. 18 M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match, complete all as specified & directed. 19 M&L for coloured glazed ceramic wall tiles as in vertical surfaces of size 450 mm x 300 mm x 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified & directed. 20 Taking down chowkats or frames including shutter (without taking off shutters from the frame) area n exc 1.50 Sqm each, complete all as specified & directed. 21 Taking down chowkats or frames including shutter (without taking off shutters from the frame) areaexc 1.50 Sqm but n.exc 4.00 sqm each, complete all as specified. 22 Taking down shutters of any description area exc 1.00 Sqm but n exc 2.00 sqm each, complete all as specified & directed. 23 S&F pressed steel frames made out of mild steel 1.25mm thick sheet, with with size of frame 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., and applying a shop coat of red oxide primer including prividing PCC 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregates) for filling back of chowkhats, complete all as specified & directed. 24 S&F pressed steel frames made out of mild steel 1.25mm thick sheet, with with size of frame 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., and applying a shop coat of red oxide primer including prividing PCC 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregates) for filling back of chowkhats, complete all as specified & directed. 25 M&L for rolled mild steel work in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe.290, Gde-E-165, complete all as specified and directed. 26 S&F 35 mm thick, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), supplied and fitted to chowkats second class hard wood, kiln seasoned and chemically pressure treated plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply. the size of rail and stile as per IS: 1003 (Part-I), complete all as specified. 27 M&L for 35mm thick 2nd class hard wood glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a), complete all as specified. 28 S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels commercial type with both faces, complete all as specified and directed. 29 S&F butt hinges, medium weight, cold rolled mild steel 100mm size, complete all as specified and directed. 30 S&F 150 mm long, aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed. 31 S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed. 32 S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing boltsand sliding bolts of extruded sections or cast aluminium complete alloy all as specified and directed. 33 S&F mild steel ordinary rat tail rod pattern springs including roller and roller plate complete 300mm length, complete all as specified and directed. 34 S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC color sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed. 35 S&F solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheetreinforced with MS square tube, complete all as specified. 36 S&F 100 mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed. 37 S&F 100mm size extruded aluminium alloy handles, fabricated type,complete all as specified and directed. 38 S&F aluminium door chowkhat with powder coating (minimum thickness of powder coating 50 micron) of 100x44x1.5mm section with rebate complete frame, complete all as specified and directed. 39 Supplying, fabricating & fixing in aluminium door shutters with powder coating (minimum thickness of powder coating 50 micron), vertical stile of door shutter of size 85mm x 44.45mm x 1.5mm thick, top, middle and bottom rail of size 85mm x 44.45mm x 1.5mm thick and fixing stainless steel wiremesh with aluminium beading and rubber gasket/ beading screws as directed. Three nos. aluminium hinges of size 100mm and two alumium tower bolts of 150mm size & 01 no. door hadnle 150mm for each shutter fixed, complete all as specified and directed by Engr-in-Charge. (Cost of wiremesh shall deemed to be included in the rate qouted for this item). 40 Supplying, fabricating & fixing in repairs aluminium partition wall with powder coating (minimum thickness of powder coating 50 micron) of aluminium section 100mm x 44mm x 1.5mm thick frame rectangular section and panel of ACP sheet and 5mm thick glass in top panel with rubber lining and aluminium beading around length including necessary fixing arrangements for bottom and top member of alumium frame in floor/ PCC/ Brick work as per site requirement with rawl plug etc, including chromium plated steel screws 60cm centre to centre, all as specified and directed by Engr-in-Charge.(Note: (Cost of sheet glass/ ACP sheet shall be measured and paid seperately). 41 Supply only for 5mm thick plain glass , complete all as specified. 42 Supply only, 4mm thick aluminium composite panel (ACP) sheetcomplete all as specified. 43 Supplying, fabricating & fixing aluminium powder coated (minimum thickness of powder coating 50 micron) glazed three track sliding window of frame 100x44x1.5mm and sliding shutter of section 40mmx19mm including 3mm thick sheet glass, ordinary quality exceeding 0.36 sqm in each pane, in two track shutter and in one track stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, all fitting such as aluminium handle of size 100mm and locking arrangement with each moving leaf, complete all as specified. 44 S&F aluminium window and ventilator shutters with powder coating (minimum thickness of powder coating 50 micron) of any colour, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21, 100mm long (2 no.), suitable handle (1 no.), complete all as specified 45 M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed. 46 S&F in replacement toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required, edges rounded and etching works etc and all kind of stainless steel patch fitting & fixtures, spider patch etc, complete all as specifed and directed. 47 S&F stainless steel handle 450mm long fixed to 12mm thick toughned glass door with and including all fixing accessories i.e. bolt, washer, adhesive etc, complete all as specifed and directed. 48 S&F stainless steel door lock, glass to glass type, suitable for 12mm frameless toughned glass door with and including all fixing accessories i.e. bolt, washer, screws, adhesive etc, complete all as specifed and directed. 49 M&L for prepration of new wooden surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthatic enamel paint over a coat of pink primer, all as specified and as directed. 50 S&F 140mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed. 51 Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones, complete all as specified. 52 S&F 4 mm thick sheet glass, ordinary quality and glazing with glazing clips/oil putty in squares not exceeding 0.5sqm in each pane, complete all as specified. 53 S&F 4 mm thick sheet glass, ordinary quality and glazing with glazing clips/oil putty in squares exceeding 0.5sqm in each pane, complete all as specified. 54 S&F 4mm thick figured glass, pin headed type in squares n.exc 0.5 sqm each pane, as in aluminum window/ ventilator/ door, including rubber packing and aluminium beading, complete all as directed. 55 S&F in repairs galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mmfixed with tinned tack or galvanised wire staples or fixed with nails and wooden beads, complete all as specified and directed. 56 S&F in repairs stainless steel curtain rod 20-22mm dia including brackets, side knobs etc, fixed to walls, complete all as specified and directed. 57 S&F in repair of ROLLER blinds vertical type 100% polyster (translucent) wt 230gm/sqm made out of fabric cloth of approved shade fixed as per the instructions of manufacturers, complete all as specified. 58 S&F in repairs venation blinds vertical type 100mm wide slats made out of fabric cloth of approved shade fied as per manufacturer instructions, complete all as specified and directed. 59 S&F in repairs 100 mm long butt hinges, medium weight, cold rolled mild steel and fixed, complete all as specified and directed. 60 S&F in repairs 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed, all as specified and directed. 61 S&F in repairs 100 mm long aluminium anodised, barrel tower bolts of extruded section and fixed, all as specified and directed. 62 S&F in repairs 150mm size aluminium alloy handle, fabricated type, anodised, complete all as specified and directed and directed. 63 S&F in repairs 100mm size aluminium alloy handle, fabricated type, anodised, complete all as specified and directed and directed. 64 S&F in repairs 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed. 65 S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of overall length 140mm, complete all as specified and directed. 66 S&F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specifed and directed. 67 S&F in repairs door closer aluminium (die casted) body, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed. 68 S&F in repairs brass mortice lock, vertical type, 4 lever of size 100 mm suitable for aluminium doors, complete all as specified and directed. 69 S&F in repairs brass mortice lock, vertical type, 2 lever of size 100 mm suitable for aluminium doors, complete all as specified and directed. 70 S&F in repair aluminium Deco grill with powder coating (minimum thickness of powder coating 50 micron), 7.5 mm size DG-102, fixed to E/H frames, 1.5mm thick, bar size 6.2mm and 7.5mm thick in required sizes, complete all as specified and directed. 71 S&Fdoor strip 50mm wide comprising of aluminium holds & rubber strip fixed at bottom of door shutter with screws, complete all as specified and as directed. 72 S&F inhasp & staple, 125 size, safety type aluminium anodised with mild steel hinge pin including bolt, to hinge plate and fixed with screws,complete all as specified and directed. 73 S&Fof cup board / drawer knob of stainless steel with matt finish fixed with screw, complete all as directed. 74 S&F brass two lever keys, locks, cupboard grade I of size 50mm suitable for cupboard door/ drawer, complete all as specified & directed. 75 S&F magnetic catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturers instructions complete all as specified and directed. 76 S&F solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and directed. 77 S&F frosted glass films sticked to toughned glasses including writing letters, logo, patterns etc if any, as directed by Engr-in-Charge and as per instructions of manufacturers, complete all as specified and directed. 78 Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, fillets etc, and removal of debries from site complete all as specified and directed. 79 M&L for exposed GI frame/ grid system duly powder coated for module size of 600 x 600 mm suitable for lay-in aluminium/ metal/ mineral fiber ceiling ties having main T runner of 24mm size, suspended at 1200 mmC/C and cross T runner of 24 mm size,suspended at 600 mm C/C with interlocking arrangement to form grid of 600 x 600 mm , perimeter runner/ channel of 15 mm size, main and cross T runner supported by 4mm dia GI rod from slab/ roof, wall angle etc with and including all fixing accessories and making good of disturbed wall surrfaces with POP and one coat of oil emulsion distemper, as required to match the existing surfaces, complete all as directed . 80 M&L for metal false ceiling, lay-in type, 0.5mm thick having tegular edge profile , duly powder coated, perforated type with glass fiber acoustic fleece, suitable for false ceiling grid/frame module of 595 x 595mm size, complete all as specified and directed. (Note : The grid/ frame shall be measured and paid separetly). 81 Demolition of stone slabs or tiles of any description or thickness in any position laid, bedded and pointed in any mortar, complete all as specified & directed by Engr-in-Charge. 82 M&L for 16-18mm thick granite of any type (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2), using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified & directed by Engr-in-Charge. 83 M&L for 18-20 mm thick machine cut kota stone slab flooring laid over and including 20 mm thick screed bed or bedding layer in CM1:6, jointed with grey cement slurry mixed with pigment to match the shade of slab including grinding, rubbing and polishing, complete all as specified and directed. 84 Providing edge moulding to 18-20mm thick granite stones of any description of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete
