Tender For Interior Renovation (Civil & Electrical) And Furnishing Of Health Centre Room At Zee Blue Amenities Centre, Nit Puducherry Campus. => Limited; 1 Civil Works 2 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 3 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 4 Single rubber stopper 5 Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. 6 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 7 100mm 8 Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes,shelves,racks,almirah,cupboard and drawer etc. including necessary nails,screws etc.complete as per direction of Engineer-in-charge. 9 Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. 10 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 11 Single tee with door 12 110x110x110 mm 13 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 14 Bend 87.5° 15 110 mm bend 16 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hardwood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 17 110m 18 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 19 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps 20 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 21 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 22 20 mm nominal dia Pipes 23 Providing and fixing uplasticised PVC connection pipe with brass unions : 24 30 cm length 25 20 mm nominal bore 26 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893 27 15 mm nominal bore 28 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 29 For fixed portion 30 Powder coated aluminium (minimum thickness of powder coating 50 micron) 31 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 32 Powder coated aluminium (minimum thickness of powder coating 50 micron) 33 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer in- charge. 34 Pre-laminated particle board with decorative lamination on both sides 35 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 36 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 37 Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595 mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32 mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8 mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted witholyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. 38 With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.60) 39 Providing, supplying and fixing aluminium sliding door consisting of extruded aluminium frame and shutter sections, powder coated (minimum 15–20 micron anodic / powder coat, colour as approved), in two-track arrangement with anodised aluminium bottom and top tracks, fitted with adjustable nylon rollers having stainless-steel ball bearings, interlocking section between shutters, 6 mm thick clear float glass panels fixed with EPDM glazing gaskets, aluminium handles, floor guide, stoppers and locking arrangement; complete in all respects and fixed to the opening as per manufacturer’s specifications and directions of the Engineer-in-Charge. 40 Providing and fixing high-quality self-adhesive privacy glass film (Frosted) minimum 0.1 mm thick window glass film on specified glass surfaces including surface preparation custom cutting and bubble-free adhesion for optimum clarity and durability the film shall have feature of 99% UV protection and 80% glare reduction daytime privacy and energy efficiency through solar heat reduction. 41 Providing and fixing ceiling-suspended cubicle curtain track system made of 22x14mm high density powder coated aluminum ‘M’ track channel fixed to the 140x100mm ‘J’ type powder double track holder angles with internal running channel; complete with bends (radius ≤ 200 mm), internal joint plates, suspension rods /tubes (SS-304 or powder-coated steel/aluminium, dia. ≥ 12 mm) spaced max. 1.5 m c/c, ceiling fixing hardware (expansion bolts / anchor fasteners), decorative ceiling flanges, 30x15mm nylon sliding castor with high quality ‘Q’ PVC hooks and fixing 25x15mm adjustable screen and channel nylon stopper, installed at level and aligned to give finished curtain drop of 2100 mm from floor level (±50 mm) all complete as per direction of Engineer-In-charge. The cost is inclusive of charges towards Transportation, Manpower and Machinery. 42 Providing and supplying hospital cubicle curtain cloth made of 100% polyester or polyester–cotton blend (minimum 150 gsm), flame-retardant to IS 11871 / BS 5867 Part 2 Type B, and antimicrobial & antifungal treated to AATCC 100 / ISO 20743 (≥99% bacterial reduction). Curtain fabric to be opaque for privacy, colourfast (4–5 to ISO 105), machine washable at 60 °C without shrinkage, breathable, and with optional top mesh panel of 300–500 mm for air circulation. Curtain to have reinforced top hem with stainless steel grommets at 150 mm c/c, 25 mm double-fold side hems, double-stitched weighted bottom hem, stitched with polyester UV- and moisture-resistant thread. Curtain fullness to be minimum 1.5× of track length all work to be complete as per direction of Engineer-In-charge. The cost is inclusive of charges towards Transportation, Manpower and Machinery. 43 Supplying and fixing Notice board for size 6’ x 4’ made using 19mm thick BWR grade plywood by finishing with 1mm thick laminated mica for all sides with display cloth fixing in inner panel face using thermocol 25mm plain tile along with velveted fabric cloth. Providing 6mm thick plain glass sliding shutter with locking arrangements all work done as per the direction of Engineer- in- Charge. The cost is inclusive of charges towards Transportation, Manpower and Machinery. 44 Electrical Works 45 Supplying, installing, testing, and commissioning of 1.5 TR capacity wall-mounted split air-conditioner, including necessary copper tubings, power and control wiring, drain water system (up to 3 meters), remote control facility, copper condenser coil, etc with rotary compressor, eco-friendly refrigerant (R410a/R32), and inverter technology; operating on single-phase 230 V, 50 Hz AC power supply; supplying and fixing of powder-coated wall bracket for mounting the outdoor unit, including drilling holes and fixing with suitable anchor fasteners; supplying and fixing of wall-mounted voltage stabilizer (Make: V-Guard VG-400) of 4 kVA capacity with LV/HV cut-off, built-in time delay, auto-restart facility, suitable for input voltage range of 170–270 V and output of 220±10 V; and supplying and fixing of extra length of twin copper refrigerant pipeline (liquid and gas lines) duly insulated with nitrile foam rubber, including laying of suitable core 2.5 sq. mm PVC insulated copper cable for power and control wiring, tightly wrapped with packing tape, providing necessary clamps/supports, etc. all complete as required. 46 Supplying, installing, testing, and commissioning of 1.5 TR capacity wall-mounted split air-conditioner(Make: Voltas, Bluestar) (3 star) 47 Supply and installtion of outdoor unit stand 48 Suplly and inatallion of Voltage stabilizer (Make: V-Guard VG-400) 49 Supply and fixing of extra length of refrigerant pipeline and power/control cable with insulation and supports if required 50 Fixing only of 103 mm X 50 mm CMS along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (CMS and flexible cover will be provided at site. Accessories are not included.) (Make: Legrand) 51 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/CMS/U-PVC mini Trunking etc as required. 52 3 x 4 sq. mm (Red , Black, Green) (Make: Finolex/ Havells/ Kei) 53 Supplying and fixing 6 module modularplate and cover In existing 103 mm X 50 mm CMS, including providing and fixing2 nos 6/16 amps modular socket outlet and 2 nos6/16 amps modular switch, connection etc. as required. (Make: Legrand) 54 Supplying and fixing 3 module modularplate and cover In existing 103 mm X 50 mm CMS, including providing and fixing1 nos 6/16 amps modular socket outlet and 1 nos6/16 amps modular switch, connection etc. as required.. (Make: Legrand) 55 Supplying and fixing 3 module modularplate and cover In existing 103 mm X 50 mm CMS, including providing and fixing1 nos 6 amps modular socket outlet and 1 nos6 amps modular switch, connection etc. as required. (Make: Legrand) 56 Supplying and fixing 6 module modularplate and cover In existing 103 mm X 50 mm CMS, including providing and fixing2 nos 6 amps modular socket outlet and 2 nos6 amps modular switch, connection etc. as required. (Make: Legrand) 57 Supplying and fixing of 2 module PVC surface box with modular plate and cover in front on surface or in recess i/c providing and fixing 3 pin 25 amps modular socket outlet with 25 amps plug top includingconnection, painting etc as required. (For A.C.Connection,socket and plug top to be fixed separately in different location as per the direction of the Engineer-in-charge). (Make: Legrand) 58 Supplying and fixing of 2 module PVC surface box with modular plate and cover in front on surface or in recess i/c providing and fixing25 amps motor starter, connection, painting etc as required. (For A.C.Connection, starterto be fixed separately in different location as per the direction of the Engineer-in-charge). (Make: Legrand) 59 Supplying and fixing of 20 W LED fitting (Make: Philips/Havells) 60 Supplying and fixing of wall mounting type fan (Make:Crompton/Havells) 61 Supplying and fixing of 2 module PVC surface box with modular plate and cover in front on surface or in recess i/c providing and fixing 3 pin 6 amps modular socket outletincludingconnection, painting etc as required. (Make: Legrand)
