Tender For Construction Of 33Kv S/S Building & B-Wall At Liyadra. - Earth work in excavation by mechanical means (Hydraulic Excavator)/Manual means in foundation trenches or drains (not exceeding 1.50 m in width or 10 Sqm on plan) including dressing of sides and ramming of bottoms,lift upto 1.5 mtrs including taking out the excavated soil and depositing and refilling of jhiri with waterng and ramming and disposal of surplus excavated soil as directed within a lead of 50 mtrs. All kinds of soils. (B-44/1.8) 2 Providing & laying in position cement concrete including curing, compaction etc .complete in specified grade excluding the cost of centering & shuttering.All work upto plinth level 1:4:8. (B-54/3.1.6) 3 Randam Rubble stone masonary for with hard stone in foundation & plinth in cement sand mortar 1:6 for above 30 cm thick walls. (B-69/6.1.6) 4 Randam Rubble stone masonary with hard stone in super structure above plinth level & upto five level for walls upto 30cm or less in thicknessin cement sand mortar 1:6 (B-69/6.2.6+6.3.4) 5 Randam Rubble stone masonary with hard stone in super structure above plinth level & upto five level for above 30 Cm thick walls in CM 1:6. (B-69/6.2.6) 6 Add exra for facing as per design & detailled specification including additional cost of stone forCourse Rubble Facing Second Sort.(B-70/6.4.2) 7 Add extra for Randam Rubble stone masonary with hard stone in Square or Rectangular Pillars. (B-69/6.3.1) 8 Providing & laying in position specified grade of cement concrete for all RCC structural elements up to plinth level including curing, compaction, finishing with rendering in CM 1:3 & making good the joints & cost of plastizers (if required) excluding the cost of centering, shuttering & reinforcement. M-20 Grade. Nominal/Design Mix. (B-59/4.1) 9 Providing & laying in position specified grade of cement concrete for RCC structural elements up to five level including curing, compaction, finishing with rendering in CM 1:3 & making good the joints & cost of plastizers (if required) excluding the cost of centering, shuttering & reinforcement for Beams, suspended floors,roofs, landings, balconies, shelves, chhajjas, lintels, staircases etc. M-20 Grade. Nominal/Design Mix. (B-59/4.3) 10 Centering & Shuttering with plywood or steel sheets including strutting, propping, bracing bothways & removal of formwork for Foundation, footings, srap beams, rafts, bases of columns etc.(B-61/4.9) 11 Centering & Shuttering with plywood or steel sheets including strutting, propping, bracing bothways with steel props & removal of formwork up to floor five level for suspeded floors, roofs, landings, balconis, girders, cantilevers, sills, chhajjas, lintels, beams, plinth beams etc.(B-61/4.10.2) 12 Providing & Fabricating steel reinforcement for RCC work including straightening, cutting, bending, placing in position &binding (incl. cost of binding wire).All complete upto floor five level. Cold twisted deformed bars. (IS:1786). (B-62/4.13.1) 13 P & L in cement concrete including curing,compaction etc. complete in retaining walls, return walls, walls including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, fillets, levelling course etc upto floor five level excluding the cost of C& S. M-10 Grade Nominal Mix 1:3:6.(B-55/3.2.4) 14 Half brick masonary in super structure above plinth level upto floor V level using bricks of designation 75 with providing & placing 2 Nos. 6mm MS bars at every third course in CM 1:6. (B-66/5.8.3+5.9) 15 Brick work in partition in super structure upto five storey 7 cm thick ( brick on edge) using bricks of class designation 75 with providing & placing2 Nos. 6mm MS bars at every third course in CM 1:4. (B-66/5.10.2) 16 Supplyng & Fixing in walls machine cut & polished stone shelves, tands & sills in CM 1:3 with machine cut edges. Kota stone minimum 30 mm thick.(B-72/6.17.3) 17 Providing & Fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joints mitred, welded & grinded including hold fast of steel lugs 13x3mm, 15 cm. long embedded in CC blocks 15x10x10 Cm. of 1:3:6 nominal concrete & including fixing of pivoted hinges of superior quality, Window shutters made out of 50x25 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred & grinded including 10x10 mm Square bars welded to frame for paitam fixing float glass 4 mm thick panes with glazing clips & metal sash putty & fixing of shutters frame peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing & jointing with frame hinges priming coat with steel primer complte in all respect as per direction of Engineer-in-charge. Window openable. (B-102/9.28.1). 18 Supplying & Fixing of fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3 mm with suitable screw at not exceeding 150 mm distance.(B-102/9.26) 19 P & F square bars or other flates welded to window, ventilators etc.(B-102/9.27) 20 Pointing on stone masonary in CM 1:3. Deep groove pointing.(B-143/12.31.3) 21 Pointing on stone masonary in CM 1:3.Flush/ Ruled/ Struck or Weathered Pointing.(B-143/12.31.1) 22 Plaster on new surface on walls in CM 1:4 including racking of joints etc. complete fine finished.25 mm thick.(B-139/12.2.1) 23 Plaster on new surface on walls in CM 1:6 including racking of joints etc. complete fine finished.25 mm thick. (B-139/12.3.1) 24 Plaster on new surface on walls in CM 1:6 including racking of joints etc. complete fine finished. 20 mm thick. (B-139/12.3.2) 25 6mm cement plaster to ceiling of mix 1:3.(B-139/12.5) 26 P & L broken glazed tiles on roof (broken glazed tiles not less than 9 Kg/Sqm) on top of hot bitumen @1.70 Kg/Sqm. (1.40 Kg of VG-40 (30/40) grade & 0.30 Kg/Sqm of VG-10 (80/100) grade) joints filled with CM 1:2 (1Cement:2 Marble dust mixed with water proofing compound) all complete as per directions of Engineer-in-charge. (B-109/10.24) 27 P & F machine cut fine dressed red/pink sand stone dasa or coping, with fuul moulding if required laid on CM 1:4 including pointing with admixture of pigment matching with the stone shade. 75 mm thick. (B-72/6.19.3) 28 P & F pressed steel door frames confirming to IS:4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead & if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.25 mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel strike-plate & shock absorber as specified & applying a coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4 (M-15 Grade) complete as directed by Engineer-in-charge. Profile- B. (B-99/9.6.1) 29 P & L in position cement concrete including curing,compaction etc .complete in specified grade excluding the cost of C & S.All work upto plinth level 1:2:4.(B-55/3.1.2) 30 P & L in cement concrete including curing,compaction etc. complete in retaining walls, return walls, walls including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, fillets, levelling course etc upto floor five level excluding the cost of C& S. M-15 Grade Nominal Mix 1:2:4.(B-55/3.2.2) 31 Cement Concrete flooring 1:2:4 finished with a floating coat of neat cement including cement slurry, making of lines or grooves etc. completebut excluding the cost of nosing of steps etc. complete. 75 mm thick with 20 mm thick nominal size aggregate. (B-128/11.3.2) 32 Providing Gola 75x75 mm in cement concrete (1:2:4) including finishing with CM 1:3 as per standard design. (B-109/10.22) 33 Finishing with neat cement (Punning). (B-140/12.7) 34 Stone slab roofing on groung floor with fine grained stone slab from approved quarry including filling of joints parapet & slab on both sides in cement sand mortar 1:4 with ceiling pointing in cement sand mortar 1:3 complete as per specification & instruction of Engineer In Charge. (B-107/10.16) 35 P&F 1 mm thick MS sheet garrage door shutter with frame of 40x40x6 mm angle iron 3 mm MS gusset plates at the junction & corners including all fittings & applying a coat of approved steel primer. (Excluding cost of frames) Using flats 30x6 mm for diagonal braces & central cross piece. (B-100/9.12.2) 36 S & F in Cement Mortar welded hand railing made out of MS round or square bars,flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paid extra) with priming coat of red oxide. (B-99/9.7) 37 Providing & Fixing steel gate grating & grills made of angles, tees, square bars or other flats, black pipe with holdfasts & fittings complete as per design & drawing including cutting, welding & fabrication with priming coat of red oxide. (B-99/9.8) 38 Structural steel work riveted, bolted or welded in built up sections, trusses & framed work including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer all complete. (B-98/9.2) 39 P & F G.I. Barbed wire of size 2.5x2.0 mm fixed with G.I. staples etc. (B-103/9.33+9.35) 40 Polished chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing & cleaning etc. complete on 20 mm thick bed of CM 1:4. Dark shade using ordinary cement. (B-131/11.17.3+11.17.5) 41 P & F external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal,dehydreresin in glue both sides with approved steel fittings complete as per Annexure-A. 30 mm thick. Commercial Veneer both side. (B-93/8.13.2.1) 42 Kota stone slabs 25 mm thick in risers of steps, skirting, dado & pillars laid on 12mm(Av.) thick CM 1:3 & jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing & polishing complete for area of each slab from 2001 to 5000 Sq.cm. (B-132/11.19.2) 43 Kota stone slab flooring 25 mm thick over 20 mm (Av.) thick baselaid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of CM 1:4. For area of each slab from 2001 to 5000 Sq.cm. (B-132/11.18.2) 44 Kota stone slab flooring 25 mm thick over 20 mm (Av.) thick baselaid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of CM 1:4. For area of each slab from 901 to 2000 Sq.cm. (B-132/11.18.1) 45 P & F 1st quality standard white, grey, ivory, fume red brown, light green, light blue & other light shades Glaged Tiles confirming to IS: 13753 & IS: 15622 of size 300x200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of the time complete (excluding the cost of cement plaster on walls & pillar). (B-86/7.12). 46 P and F 1st quality MAT finished ceremic tiles size 300mm x 300mm confirming to IS:13755 & IS: 15622 colour such as white, grey, ivory, fume red brown, light green, light blue & other light shades infloors, steps, pillars etc laid on a bed of neat cement slurryfinished with flush pointing in white cement mixed with pigment to match the shade of tile complete (including the cost of cement mortar bed). (B-86/7.13) 47 P & F of Rolling shutters of approved make,made of 80x1.25mm MS laths interlocked together through their entire length & jointed together at the end by end locks mounted on specially designed pipe shaft with brackets,side guides & arrangement for inside & outside locking with push & pull operation complete incl. cost of spring hooks, P & F necessary 25.3 cm. long wire spring grade No.2 & MS top cover 1.25 mm thick for rolling shutters as per design & IS: 6248-1979.(Clear openable area to be measured for payment). (B-100/9.13) 48 P & F of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80x25x1.25 mm thickwith 1 mm MS sheet to spot welded including holdfast of 15x3 mm, MS oxidised fittings such as butt hinges, sliding doors bolts, handles, tower bolts & twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate & spray painting in approved shade with deco paint of approved quality complete as per direction of Engineer In Charge. (B-104/9.39) 49 Making grooves as per design in plaster 10 to 20 mm wide.(B-141/12.19) 50 Clearing grass & removal of rubbish up to distance of 50 mtr outside the periphery of area cleared. (B-49/1.32) 51 Earth work in surface excavation not exceeding 30 Cm in depth but exceeding 1.50 M in width as well as 10 Sqm on plan including disposal of excavated earth up to 50 M lead lift up to 1.50 M disposed soil to be levelled & neatly dressed. All kinds of soil. (B-43/1.1) 52 Providing & Laying of Paver blocks as per IS:15658:2006 (Indian standard for precast concrete block for paving specifications) & IRC: SP63-2004 (Guidelines for the use of interlocking concrete block pavements). M-40, 80 mm thick to be used in medium traffic ( Medium traffic is defined as a daily traffic of 150-450 commercial vehicles exceeding 30 KN laden weight or an equivalent of 0.50 to 2.0 MSA for a design life of 20 years) like City streets, small & medium market roads, low volume roads, utility cuts on arterial roads etc. Category-C not denated on any of its faces like Hexagonal, rectangular, square shape as per IRC: SP63-2004. (B-136/11.38.3(C)) 53 P & L cement concrete Kerb Stones of different sizes in M-30 Grade (Manufactured with fully mechanised dry cast process with firced action mixer whose arms revolve along the main axis & rotate about its own axis also, having humidity sensor for moisture control of w/c ratio in concrete mix. Manufactured with steel moulds (Milled & manufactued in CSI diamond or CSI Nitro process for accuracy) on steel base of min 16 mm thick, having vibration & pressing action both together with the help of multiple synchronised vibrators. Power of hydraulic station should be min 50 KW for compaction & curved in controlled chambers having humidity control & automated air circulation system in position to the required line, level & curvature jointed with CM 1:3 including making of joints, drainage opening wherever required. (B-208/17.21) 54 S & L & Transporting of gravel/mooram binding material having PI not less than 4 to 6 complete in required grade & camber including all lead & lift. 55 White washing with lime to give an even shade including all scaffolding.New work (three or more coats). (B-143/12.34.1) 56 Finishing wall with water proofing cement paint of approved brand & manufacture & or required shade to give an even shade including all scaffolding. New work (Two or more coats applied @ 3.84 Kg/10 Sqm). (B-145/12.41.1) 57 Painting with synthetic enamel paint of approved brand & manufacture to give an even shade.Two or more coats on New work.(B-146/12.46.1) 58 P & F Indian type White Glazed Vitreous China 1st quality W.C. Orissa Pan IS:2556 Mark) with 100 mm vitrous china P or S trap including cutting & making good the walls & floors of size 580x440 mm.(BS-217/1.2.2) 59 P & F WVC Wash Basin (1st quality, IS:2556 Mark) of approved make with C.I. brackets duly painted, 1No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall of size 510x440 mm.(BS-221/1.36.2) 60 P & F Chlorinated Poly Vinyl Chloride (CPVC) pipes (IS:15778:2007 code) having thermal stability for hot & cold water supply including all CPVC plain & Brass threaded fittings including fixing the pipe with clamps at 1 meter spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement & the cost of cutting chases & making good the same including testing of joints complete as per directions of Engineer In Charge. (Concealed work including cutting chases & making good the walls etc.). 15 mm Nominal size. (BS-240/2.38.1) 61 P & F Chlorinated Poly Vinyl Chloride (CPVC) pipes (IS:15778:2007 code) having thermal stability for hot & cold water supply including all CPVC plain & Brass threaded fittings including fixing the pipe with clamps at 1 meter spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement & the cost of cutting chases & making good the same including testing of joints complete as per directions of Engineer In Charge. (Concealed work including cutting chases & making good the walls etc.). 25 mm Nominal size. (BS-240/2.38.3) 62 P & F Chlorinated Poly Vinyl Chloride (CPVC) pipes (IS:15778:2007 code) having thermal stability for hot & cold water supply including all CPVC plain & Brass threaded fittings, this includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per directions of Engineer In Charge. (External work) . 15 mm Nominal size. (BS-240/2.39.1) 63 P & F Bib Cock (IS:8931 Mark) Superior quality of approved make C.P. Brass Bib Cock 15 mm. (B-232/2.7.3) 64 P & F Bib Cock (IS:8931 Mark) Superior quality of approved make. Brass 400 gm. 15 mm nominal bore. (B-232/2.7.1) 65 P & F Inlet Connection (Angle Valves) Superior quality of approved make for Wash Basin, Gyser etc. C.P. Inlet Connection 15mm Brass. (IS:8931 marked. (B-233/2.12.1) 66 P & F Ball Cock (IS:1703 Mark) with Rod & PVC Ball complete : Brass wt. not less than 300 gm. 15 mm. (B-232/2.11.1) 67 P & F 15 mm dia. Connection pipe of approved quality/make. PVC pipe with C.P. Brass nuts up to length 450 mm. (B-233/2.13.3) 68 P & F Flush Cock/Flush Valve (IS:9758 Mark) for WC of approved make. C.P. Brass push type, 20mm nominal bore. (B-233/2.14.2) 69 P & F Full-way (IS:778 Mark) or Wheel valve of approved make :Gun-metal 15 mm nominal bore. (B-233/2.15.1) 70 P & F Full-way (IS:778 Mark) or Wheel valve of approved make :Gun-metal 25 mm nominal bore. (B-233/2.15.3) 71 P & F PVC Storage Tank ISI Marked (IS:12701, Indicating BIS license No.) of approved make with cover, 25 mm dia. 1 M long G.I. over flow pipe & 25 cm long wash out pipe with plug & socket, including making connection etc. complete of approved design. 500 litres capacity. (B-236/2.26.3). 72 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type B for sciland waste discharge system (IS:13592:1992 Marked) of approved quality/make. 75 mm Dia. (B-257/3.44.1) 73 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type B for sciland waste discharge system (IS:13592:1992 Marked) of approved quality/make. 110 mm Dia. (B-257/3.44.2) 74 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipe fittings type B for sciland waste discharge system (IS:13592:1992 Marked) of approved quality/make. Bend 87.5 Dg. 110 mm Dia. (B-257/3.45.4(ii)) 75 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipe fittings type B for sciland waste discharge system (IS:13592:1992 Marked) of approved quality/make. Single Tee with Door, 110 mm Dia. (B-258/3.45.17(ii)) 76 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipe fittings type B for sciland waste discharge system (IS:13592:1992 Marked) of approved quality/make. Vent Cowel 110 mm. (B-259/3.45.30) 77 P & F Square-mouth Gully Trap A grade (IS:651-1992 Marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in CM 1:6, 100 mm thick C.C. 1:5:10 base concrete, 40 mm thick C.C. M-15 grade coping, 12 mm thick cement plaster in CM 1:3 complete as per approved design & type. Trap size 150x100 mm, RCC cover of size 300x300 mmwith frame, Internal Chamber size 300x300 mm.(B-244/3.5.1) 78 Construction of Manhole in all type of soils inner size 90x60 cm., 300 mm thick masonary in CM 1:6, 10 cm. thick C.C. 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6 finished with floating neat cement, 50 mm thick M-15 grade C.C. flooring, making channels, 80 mm thick stone slab covering with 40 mm thick M-15 grade C.C. flooring, Cement cover with frame of 450 mm dia. earthwork etc. complete as per design including disposal of surplus earth within 50 Mtr. lead. Depth upto 0.50 Mtr. (B-250/3.19.1) 79 Construction of Soakage Well in all type of soils 300 mm thick dry masonary, top & bottom 300 mm course in CM 1:6, 80 mm thick stone slab, jointing of slab in CM 1:3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C. flooring, earthwork etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 Mtr. of size 240 cm dia. outside & 240 cm depth. (B-252/3.22.3) 80 Making Connection of G.I. distribution branch with main including all fitting upto 25 mm dia. (B-231/2.3.1) 81 P & F Looking Mirrors with PVC frame of approved make as per directions of Engineer-In-Charge. of size 500x400 mm . (B-223/1.45.1) 82 P & F towel rail or ringof approved quality/make. C.P. brass towel rail with bracket600x20 mm.(B-223/1.47.4) 83 Construction of Cement Concrete Chamber 125 mm dia. Stainless Steel sheet grating. (B-255/3.38.4) 84 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR Short point (up to 3 mtr.)E-01/1.1.1 85 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSRMedium point (up to 6 mrt.) E-01/1.1.2 86 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSRLong point (up to 10 mrt) E-01/1.1.3 87 Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) inrecessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & its ISI marked (IS:3419-1988)accessories, Hot Dipped GalvanizedModular box of 1.2 mm thick with earth terminal, 10 A modularswitch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR. On board E-02/1.3.1 88 S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along withISI marked (IS:3419-1988) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure A attached with this BSR. 25 mm E-02/1.4.2 89 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR. 2x2.5 Sq mm + 1x1.5 Sq mm E-04/4.1.7 90 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR . 2x4 Sq mm. + 1x2.5 Sq. mm. E-04/4.1.14 91 Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification ofWiring accessories refer ChapterE - 07related item & For additional technical parameters of product / work refer Annexure A attached with this BSR. E-07/7.37 92 P & F 1.2 mm thickG. I. / M .S. Sheet boxes duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in recessed/surface as required.For additional technical parameters of product / work refer Annexure A attached with this BSR. 250mm x 300mm x 75mm E-05/13/5.1.1.11 93 P & F 1.2mm thickM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure A attached with this BSR. E-05/15/5.9 94 P & Fof IP-65 IK08, IP-66 rated integrated SMD mid power LED bulk head type light fixture made from pressure die cast AL housing suitable with integral driver, system lumen efficiency >100 Lm/Watt output, THD<10%, PF>0.95, CRI>80, life time of minimum 50000 burning hours with 70% of initial Lumen maintened till life ends, CCt 3000K/4000K/5700K/6000K/ 6500K (AS per ANSI Bin), maximum power consumption should not be more than the specified rating & fixture shall be of BIS standard & trade mark certificate (TC). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing, surge protection 4 KV. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate/Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of product/work, refer Annexure A attached with this BSR. Minimum Lumen output 1000 Lm. (E-17/17.6.1). 95 Pipe Earthingas per IS:3043- 1987 with 3.0 Mtr. Long, 40 mm dia. B class G.I. Pipe IS: 1239 (Part-1) 2004, Equivalent to BS : 1387 with perforated holes of 12 mm dia ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . E-14/73/14.1 96 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR 6 A to 32 A rating E-06/17/6.1.1.2 97 Providing & Fixing of 240/415 V Isolator ISI marked IS:13947-III/confirming to IEC:60947-3, suitable for AC22A utilization category, 4 KV impulse withstand voltage, true contact indication, red colour dolly/lever shall have single mould covering over all poles for operation, two position din rail mounting, minimum phase minimum phase termination capacity of 35sq.mm. , IP 20 contact protection and fitted inexisting distribution board/sheets including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR. Double Pole Isolator of 30/40 A rating E-06/18/6.2.1.1 98 P & F of Recessed/Surface mounting heavy duty enclosure made out from Galvanized steel/CRCA sheet not less than 1.2 mm thick confirming to IS:8623-1 & 3/IEC:61439-1 & 3. Powder painted complete with din bar making integral DB terminations with copper lugs, detachable gland plate including making connections, testing ect. as required. For additional technical parameters of product / work refer Annexure A attached with this BSR. Suiatable for 6/8 Module for MCB/RCCB. (E-06/21/6.9.2). 99 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 1170mm (+/-10%) LED batter with min. lumen output 2200 lm E-17/87/17.1.1 100 Providing & Fixing of energy efficient direct fit (Retrofit)Polycarbonate/ GlasshousingSMD Mid Power LED tube rod(with integral driver & alumn. heat sink ), on existing fixture.system lumen efficacy ≥ 100 lm/Watt output, internal surge protection of 2.5 KV ,THD < 20% ,p.f.≥0.95,CRI >80 , life time of minimum35000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80)certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 600mm , Min Lumens output 1800 lm LED Tube rod with Polycarbonate housing E-17/87/17.2.1 101 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,making connection with GI/Cu purity purity >95%thimble etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 10 SWG G.I. (Hot Dipped) wire E-14/75/14.6.9 102 Providing & Fixing of IS 11037:1984markednon modular socket size flush type 180 watt rotary minimum 5 step fan regulator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .E-07/30/7.21 103 Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 1200 mm Sweep E-15/81/15.7.3 104 SITC of Monoblock motor pump set ISI marked (IS:9079-2002) with TEFC motor, motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,& IS12615:2011. with Stainless steel Impellor, Stainless steel shaft, Mechanical seal, Single/Three phase ( 240 - 440 V ) permanent split capacitor type (PSC), fitted with thermal overload protection, Including cost of hardware etc on existing platform complete. Pump shall have following HP Rating, phase, Head, minimum Discharge respectively complete in all respect. OEM shall have submitNABL / CPRI / ERDA accrediatedlab type test certificate before execution. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 0.5 HP E-21/115/21.7.1 105 S & F of Office Steel table heavy duty of size 4x26x26 with 3-Drawers having separate lock & partition below each drawer of sheet 22g, square pipe 1, 16g. Top of table having 18 mm ISI marked particle board with teak wood beading & polish & fixed on square pipe 1 & one footrest of same section. 106 S & F of standard sizeheavy duty Steel Office chair full arm with Maharashtra Cane seat back in tubular pipe 1, 16g. 6 sut pipe inserted in 1 pipe at every turn or pipe. Seat of size 430x380 mm resting over pipe & back to be held on pipe dully painted with enamel paint of superior quality. 107 Supply of steel 3 seated chair set made of iron 62 in length & each seat of size 17x18 with hand rest structure made of round pipe 2 & square pipe 2x1 & 1/2 round pipe frame in which perforated sheet 20g is fixed which is dully factory painted with powder coated of superior quality complete in all respect. 108 Supply & Fixing of steel stool 12x1218 with 19 mm board sunmica top with beading pipe 1,18g with angle iron frame of angle 25x25x2 mm. 109 Supply of different varieties of Trees/shrubs/climbers accordingto height & age of the plant at side including loading/unloading & transportation etc. complete. Diffrent flowering plants 900 to 1500 mm. (B-273/1.11.1) 110 Supply of different varieties of Bongainvileas in poly bags/earthen pots according to height growth & age of plant at site including loading/unloading & transportation complete. Different varieties of Bongainvillea 600 to 900 mm. (B-273/1.12.2) 111 Supplying & Fixing of Direction & Place Identification Sign Board made out of 2 mm thick MS sheet framed to angle iron 40x40x5 mm & two vertical posts of angle iron of size 50x50x5 mm, 3 mtrs. long with holdfasts, grouting in concrete mix 1:3:6 block of size 0.30x0.30x0.45 mtr. stove enamelled paint with reflective letter symbol complete of size 90x60 cm.
