Tender For Additional Facility To New Bus Stand In Mmc; 1 Installation of Vertical Bored cast in situ RCC piles of following diameter in all types of soils, using Standardised Concrete Mix of following grade, with sulphate resistant Cement or OPC/PPC, etc and Crushed Stone Sand and 20mm and down graded HBGS jelly coarse aggregate. The rate includes cost for placing of reinforcement cage in bore hole in correct position, cost of boring to the required depth with Bentonite solution with temprory casing of required length, conveyance of RMC to site and pouring concrete using Tremine pipes, conveyance of all materials to the site including all tools and plants, shifting the plants and equipments from one point to another, excavtion of mud pits for circulation of Bentonite soultion, closing the mud pits to original level and mud removal with initial lead and lift but including dismantling the concrete above the cut off level etc complete as directed by the departmental officers including socketing. The reinforcement cage should be welded properly for lifting. The concrete cubes to be tested as per IS 456-2000. Acceptance criteria by clause 16.1. Frequency of testing as per 15.2.2. Testing to be conducted at both the ends at site as well as RMC plant. Pile driving depth should be decided by the departmental officers at site. The length of pile for payment shall be measured from top of shoe to the bottom of the pile cap.( Cost of Reinforcement provided for Pile and Welding charges shall be measured and Paid separately ) 2 Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire) 3 Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers. 4 Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 5 Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers. -Mixing by manual means 6 Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require onlynominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener,side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid). 7 Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.- Mixing by manual means 8 Providing and laying in position, standardised concrete Mix M-20 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without inspiring strength and durability with about (5 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost ofreinforcement grill and fabricating charges, centering and shuttering and also including laying,vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc.,complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials). 9 Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification 10 Supplying , fixing and roofing with colour galvalume sheet of 0.47mm thick with allnecessary accessories such as J/V bolt and nuts of suitable length with suitablebitumen washers complete complying with standard specification and as directed bythe departmental officers. 11 Supply and filling in foundation and basement with Gravel in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 12 Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications 13 upplying and laying of Interlocking Paver Block Stone 60mm thickOver a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc complete complying with the standard specification and as directed by the departmental officers. 14 Supplying and filling in foundation, basement, etc with conveyed earth in layers of not more than 150mm thick layers well watered, rammed with surface vibrator andconsolidated including conveyance charges etc. complete complying with standard specification and as directed by the departmental officers. 15 Wiring with 2 x1.5 sq.mm.PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box on wall with 6A one way module switch with module front plate with painting of Suitable colour withcontinuous earth wire connection of 1.5 sq.mm copper wire forOpen MS conduit Light point / fan point (for electronic regulator) ( 5 points / Coil) Higher End (SD-235) 16 Supply and fixing of single box type 40 W LED fitting (Philips / Havells / Eq) with CRCA body complete with TW round blocks on wall or ceiling with 20 W LED tube with PVC unsheathed Copper leads from terminals to the fitting (SD-88). 17 supply and fixing of 18W LEDround type Recessedfitting with LED (Higher end) on false Ceilingwith suitable hanging support from ceilingwith PVC unsheathed copper leads from terminals to the fitting (SD-452). 18 supply and fixing of 40W LED 2x2 square type Recessedfitting with LED (Higher end) on false Ceiling with suitable hanging support from ceilingwith PVC unsheathed copper leads from terminals to the fitting (SD-448). 19 supply and fixing of 1200mm (48) sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end)with 300 mm down rod on the existingfan clamp . (SD-467) 20 Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos.6A one module switch with module cover plate (plastic) onsuitable module concealedBox (GI ) in flush with wall with connections. Higher End (SD-476). 21 Supply and fixing of 6 Watts LED Round Type Surface mounted Down Light with PVC unsheathed copper leads from terminal to the fitting (SOR -M-3018) 22 Supply and fixing of 7 segment 6 way triple pole neutral MCB distribution boardin sheet steel enclosure double door type with metal door with IP 42 protection with 63A 4 pole MCB isolator as incoming and 3Nos 63A DP RCCB as sub incomer and 18 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (The MCBDB andMCBs should be with Legrand / Hager make) (SD-560). 23 supply and fixing of 150W LED street light fitting with LED (Higher end) with 40mm dia. GI pipe (class B) with 1 no.40 mm GI bend complete on the existing post/ on wall with 1.5 sq.mm PVC unsheathed copper leads with MS clamps and withpainting . (SD- 539) 24 Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigidpipe Concealed inwall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion withsuitable colour .(SD-414) 25 Supply and run of 2 of 4 sq.mm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour (SD-57). 26 Supply and run of 4 of 6 sq.mm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour for 63A 4P MCB and 63A 3Phase DB. (SD-343). 27 Supply and Laying of 3.5C X 240 sq.mm. PVC armoured LTUG cablein suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good(SD -676) 28 Supply and providing cable end termination of 3.5Cx 240 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete (SD-230). 29 Design, supply, fabrication, erection, testing and commissioning of 200 A dust and vermin proof floor mounting cubical type panel board of size not less than (size 11ft x 6ft x1ft ) made up of 16SWGCRCA sheet steel for outer body and stifferness doors and switches supports and supply and fixing of following intermounting switches with centre bus bar chamber and two rows of switches with cable adopter chamber for all swiches with two coats of quality paint over the coat of red oxide primer and superscription of incoming and outgoing feeder cable, details and 2 Nos. metalic danger board complete mounted on base channel(3X 1.5X1.5) irn frame work aupport with following switch as confirming to IS specification. 1. 40A FP isolator(LegrandHager make) (SR) - 18nos 2. LED pilot Lamp arrangement with switch and with multification meter with necessary CT connection complete - 1 No. The incoming 200 A Fuse units should be connected to the bus with 1 X 14 copper bus bar & 18 Nos. 0f 40 A FP isolator should be connected to the bys by 6 sa.mm (840.3) PVC insulated single core multisrand FRLS flexible cu wire. The switches should be properly earted by solid copper flat as per IE rules and CEIG specification. (Data- 10) 30 commissioning of 200 a dust and vermin proof floor mounting cubical type panel board of size not less than (size 11ft x 6ft x1ft ) made up of 16SWGCRCA sheet steel for outer body and stifferness doors and switches supports and supply and fixing of following intermounting switches with centre bus bar chamber and two rows of switches with cable adopter chamber for all swiches with two coats of quality paint over the coat of red oxide primer and superscription of incoming and outgoing feeder cable, details and 2 Nos. metalic danger board complete mounted on base channel(3X 1.5X1.5) irn frame work aupport with following switch as confirming to IS specification. 1. 40A FP isolator(LegrandHager make) (SR) - 18nos 2. LED pilot Lamp arrangement with switch and with multification meter with necessary CT connection complete - 1 No. The incoming 200 A Fuse units should be connected to the bus with 1 X 14 copper bus bar & 18 Nos. 0f 40 A FP isolator should be connected to the bys by 6 sa.mm (840.3) PVC insulated single core multisrand FRLS flexible cu wire. The switches should be properly earted by solid copper flat as per IE rules and CEIG specification. (Data- 11) 31 Supply & erection of 200A rated dust &verminproofcubicle panel board of size not less than 5x6x1.5made out of 16SWG CRCA sheet steel with bus bar chamber, cable chambers, switching consoles with hinged doors etc. with necessary stifners on suitable angle iron frame supports with wall mounting arrangements complete with the following accessories. 32 Supply and fixing of 12 Mtr Mini Mast suitable for 180 km/hr wind speed and siitable for mounting Max 6.of luminaires consisting of : Head Frame, Movable lantern carriage,Double drum Winch 6mm 316 Grade, S.S Hoisting ropes of 7/19 construction Flexible Multicore cable Trailing cable - 5core X 4sq.mm 1per mast Foundation Bolts & Nuts Anchor Plate & Template,Lightning finial Twin aviation light (GLS type), Power tool (Integral) ,Feeder Pillar for automatic operation, Casting of Foundation and Installation / Testing & Commissioning Supply, installation of 8Nos of 150W LED fittings with CG boxes and lamps. 33 Supplying and fixing in position best quality PVC soil / waste pipes of various dia having6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level 34 Supply and Delivery of 3 Seater Waiting Area Sofa/Visitors Reception Heavy Chair in Stainless Steel.The rate is inclusive of the charges for cutting ,bending ,welding,grinding,polishing,conveyance,electrical charges,etc, 35 Supplying and erecting in position of following 500 liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.
